Académique Documents
Professionnel Documents
Culture Documents
SCAN-100
FUNCTION SELECTION
Check the Trouble Code
Preceding Work: Perform the Entering Diagnosis Procedures
2. The DIAGNOSTIC TROUBLE CODEs screen is displayed and it shows the trouble. NOTE
If there is not any fault, NO TROUBLE DETECTED message appears.
3. When selecting a trouble code, then if you press : Displays the sensor data for the detected trouble (Freeze Frame Mode). : Displays the help tips for the detected trouble.
if you press
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
31
SCAN
in FUNCTION
3. Select the items you want to see and press key to freeze them. NOTE
You can freeze up to 5 items (*: selected items).
DIAGNOSIS
ACTYON SM - 2006.03
ECU
32
SCAN-100
Actuator Check
Preceding Work: Perform the Entering Diagnosis Procedures
in FUNCTION
2. The screen shows 19 items. Select the item you want to see and press .
3. For example, if you select 02] GLOW PLUG item and press , the screen as shown in figure is displayed.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
4. If you want to operate the glow plug relay, press key. The ACTIVATING message appears and the relay operation alarm sounds.
33
SCAN
key in
DIAGNOSIS
ACTYON SM - 2006.03
ECU
34
SCAN-100
in
2. The DIAGNOSTIC TROUBLE CODEs screen is displayed and it shows the trouble. NOTE
C = Current trouble, H = History trouble
3. Fix the trouble and go back to 1] TROUBLE CODE screen and check if the trouble has been changed to H (History trouble code) code.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
4. If the trouble has been change to H (History trouble code) code, press key to go back to FUNCTION SELECTION screen. In this screen, select 4] TROUBLE CODE CLEAR and press .
35
SCAN
5. The TROUBLE CODE CLEAR screen is displayed. If you press , only the history trouble codes will be cleared. NOTE
Current trouble codes will not be cleared. Check the trouble codes after clearing the trouble codes.
DIAGNOSIS
ACTYON SM - 2006.03
ECU
36
SCAN-100
ECU Identification
Preceding Work: Perform the Entering Diagnosis Procedures
2. The ECU IDENTIFICATION screen that shows the VIN, ECU software number, ECU software version and programming date is displayed.
to input the
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
37
SCAN
2. The INJECTOR (C2I) CORRECTIONS screen that shows current C2I coding values of #1 to #4 injector is displayed.
3. If you replaced the ECU, enter the C2I value of the relevant injector.
DIAGNOSIS
ACTYON SM - 2006.03
ECU
38
SCAN-100
NOTE
The C2I value of replacing injector is recorded in the label. C2I coding number: 16 digits (ex, B1 B9 D4 1B 43 C6 0E 4F)
1) If you enter the invalid C2I value of the relevant injector, the message as shown in figure appears with alarm sound. NOTE
If you want to go back to previous screen, press key. You can see the previous C2I value.
2) If you enter the valid C2I value of the relevant injector, the message as shown in figure appears with alarm sound.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
39
SCAN
Leak Detection
Preceding Work: Perform the Entering Diagnosis Procedures NOTE
This item is for checking the high fuel pressure after the IMV supply line of HP pump in DI engine fuel system. If you still suspect that the fuel pressure system is defective even after no trouble is detected, perform the fuel pressure test again by using a fuel pressure tool kit.
in
2. The LEAK DETECTION screen that shows the checking conditions as shown in figure is displayed.
DIAGNOSIS
ACTYON SM - 2006.03
ECU
40
SCAN-100
Preceding page
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
41
SCAN
Variant Coding
Preceding Work: Perform the Entering Diagnosis Procedures
in
2. When the VARIANT CODING screen is displayed, . select 1] READ VARIANT VALUE and press
DIAGNOSIS
ACTYON SM - 2006.03
ECU
42
SCAN-100
4. The VARIANT CODING screen that shows currently equipped devices is displayed.
ENGINE
CHASSIS
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
43
SCAN
Selection
NO/YES NO/YES
Description
ECU
is automatically selected.
Select only for the vehicle with PTC type supplementary heater (in DI engine). Select Select only for the vehicle with auto cruise system. only for the vehicle with immobilizer system.
No remote starter system is applied to this model. However, must select to confirm that this vehicle doesnt have remote starter. CAN Select. Select Select only for the vehicle with ABS or ESP system. only for the vehicle with part time TC system.
Vehicle speed signal ABS or ESP TOD/Part time TC (4WD) Air conditioner
Select only for the vehicle with A/C system. (W/O Aircon : NO) Select only for the vehicle with M/T neutral switch.
NO/YES(WIRE)/CAN
Selection
D20DT/G23D DOM/GENERAL/EU Yes/No MT/DC5AT/BTRA AT ION(BTRA)/DC LEVER/DURA LEVER NA/ABS/TCS/ESP NO/YES NA/TOD/PT 4WD/ AWD/PT 4WD (W/O 4L) SEDAN/LIMOUSINE ACTYON CODING COMPLETED NA/ECS/EAS(2)/EAS(4) NO/YES NO/YES
Description
Select the appropriate engine. Select the region. W/ Telematics: Yes W/O Telematics: No Select the appropriate system. Select the appropriate selector lever. (For DI engine equipped vehicle, select ION (BTRA)) Select the appropriate system. Select only for the vehicle with ECPS system.
Select the appropriate system. Select SEDAN - Automatic coding. Select ACTYON - Automatic coding. Select the coding status. Select the appropriate system. Select Yes only for the vehicle with EPB system. - Automatic coding Select only for the vehicle with TPMS system.
DIAGNOSIS
ACTYON SM - 2006.03
44
SCAN-100
4. If you need to change the variant coding, press key to go back to VARIANT CODING screen. In the screen, select 2] WRITE VARIANT CODING and press .
5. When the WRITE VARIANT CODING VALUE screen is displayed, change the item by using arrow keys.
6. If you press , the message as shown in figure appears. And, then VARIANT CODING screen is displayed.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
45
SCAN
* Chassis variant coding should be done in the same procedures as for Engine variant coding.
DIAGNOSIS
ACTYON SM - 2006.03
ECU
46
SCAN-100
ECU Replace
Preceding Work: Perform the Entering Diagnosis Procedures 1. Select 9] MISCELLANEOUS and press FUNCTION SELECTION screen. in
in
3. Before starting ECU replace, check the ECU S/W version of old ECU and new ECU.
4. When the ECU REPLACE (STEP 2) screen is displayed followed by ECU REPLACE (STEP 1) screen, turn the ignition OFF and remove the currently installed ECU. NOTICE
Do not turn off the Scan-100 at this time. Record the below data: 1) Vehicle identification number 2) Variant coding value 3) C2I coding value 4) Multi calibration
DIAGNOSIS
ACTYON SM - 2006.03 CHANGED BY EFFECTIVE DATE AFFECTED VIN
SCAN-100
5. Install the new ECU.
47
SCAN
, the message as shown in figure 1 (system 6. If you turn the ignition switch to ON position and press initialization) appears, and then MULTI CALIBRATION screen (figure 2) is displayed. figure 1 figure 2
DIAGNOSIS
ACTYON SM - 2006.03
ECU
48
SCAN-100
9. If the multi calibration is completed successfully, ECU REPLACE (STEP 5) screen is displayed. Backup data: 1) Multi calibration value 2) VIN value 3) Variant code value 4) Injector (C2I) value
10. In immobilizer equipped vehicle, the immobilizer coding should be done after completed the multi calibration.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
11. Press for the vehicle equipped with immobilizer system.
49
SCAN
12. Follow the instructions on the display of Scan-100. - Identification of VIN number - Immobilizer coding
#1
#2
#4
#3
#5
#6
DIAGNOSIS
ACTYON SM - 2006.03
ECU
50 #7
SCAN-100 #8
# 10
#9
# 11
# 12
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
13. Press to return to MAIN MENU screen.
51
SCAN
DIAGNOSIS
ACTYON SM - 2006.03
ECU
52
SCAN-100
in
3. If the versions of ECUs are not matched, program the new ECU after replacement.
4. VIN/Variant Data/C21 Data is not read from ECU. Press to run the multi calibration.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
5. Select the appropriate model in MULTI CALIBRATION SELECTION screen. 1) Vehicle with A/T: 2] Dom/Gen A/T 2) Vehicle with M/T: 4] Dom/Gen M/T
53
SCAN
6. If the multi calibration is completed successfully, the message screen shown in the figure is displayed. 7. The VIN/Variant Data/C21 Data should be input manually.
8. To enter the data, press ESC on the screen in Step 5 and go back to main screen. 9. To enter the VIN, select 5] ECU IDENTIFICATION . and press
10. Press
DIAGNOSIS
ACTYON SM - 2006.03
ECU
54
SCAN-100
11. Enter the VIN into the number plate on the screen. To change the number to the character, use the arrow keys.
12. Select 6] INJECTOR (C2I) CORRECTIONS and press in FUNCTION SELECTION screen. Remove the engine acoustic cover and enter the 16 digits code on each injector label for all of five injectors. If any of digits is wrong, you should enter full code again. Make sure that the VIN code is correct. The nearest injector from the radiator is number 1 and the number goes higher as it moves away.
13. Select 8] VARIANT CODING and press PRESS in FUNCTION SELECTION screen. When the VARIANT CODING screen is displayed, select 2] WRITE VARIANT CODING and press PRESS. When the WRITE VARIANT CODING screen is displayed, change the item by using arrow keys.
DIAGNOSIS
ACTYON SM - 2006.03
SCAN-100
55
SCAN
DIAGNOSIS
ACTYON SM - 2006.03
ECU
56
SCAN-100
3. Enter the current rail pressure value and press [ENTER] to reset the offset value.
4. The screen returns back to step 3 after displaying the [RAIL PRESSURE RESET IS SUCCESSFUL] message. NOTICE
If the offset value is not set to 0, check the fuel pressure and other DTC generations before starting the rail pressure reset operation.
DIAGNOSIS
ACTYON SM - 2006.03