Académique Documents
Professionnel Documents
Culture Documents
Dell E1909Wc
Table Of Contents
Description Page Description Page Table Of Contents...........................................1 Revision List................................................2 ECN History................................................3 Important Safety Notice...........................4 1.Monitor Specifications.....................................5 2.LCD Monitor Description.......6 3.Operation Instructions..........................7 3.1.Control Buttons.............................7 3.2 Adjusting the Picture.....................9 4.Input/Output Specification.....................17 4.1.Input Signal Connector.............................17 4.2.Factory Preset Display Modes...........................18 4.3.Power Supply Requirements.............................18 4.4.Panel Specification.......................19 4.5 Incoming inspection standard...................................21 5. Block Diagram...25 5.1.Software Flow Chart.............25 5.2.Electrical Block Diagram............27 6.Mechanical Instruction.............29 7.Schematic Diagram.......................................34 7.1Main Board............................................34 7.2 Power Board.......................................38 7.3 Key Board....40 8.PCB Layout............................................41 8.1.Main Board..........................................41 8.2.Power Board........................................43 8.3.Key Board.....................................44 9.Maintainability.......................................45 9.1.Equipments and Tools Requirement..............45 9.2.Trouble Shooting.............................45 10.White-Balance, Luminance adjustment........51 11.ISP Instruction..................................53 12.Monitor Exploded View.............57 13.BOM List.....................................................59 14.Different Parts List...71
SAFETY NOTICE ANY PERSON ATTEMPTING TO SERVICE THIS CHASSIS MUST FAMILIARIZE HIMSELF WITH THE CHASSIS AND BE AWARE OF THE NECESSARY SAFETY PRECAUTIONS TO BE USED WHEN SERVICING ELECTRONIC EQUIPMENT CONTAINING HIGH VOLTAGES. CAUTION: USE A SEPARATE ISOLATION TRANSFOMER FOR THIS UNIT WHEN SERVICING
Dell E1909Wc
A00
Jun.-16-2008
Initial Release
A01
Aug.-12-2008
T9RMMAHKX5DFHC T9RAMAHKX5DFHC
Dell E1909Wc
Cut-in date
MSR
Dell E1909Wc
Proper service and repair is important to the safe, reliable operation of all AOC Company Equipment. The service procedures recommended by AOC and described in this service manual are effective methods of performing service operations. Some of these service operations require the use of tools specially designed for the purpose. The special tools should be used when and as recommended. It is important to note that this manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It is also important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. AOC could not possibly know, evaluate and advise the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, AOC has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by AOC must first satisfy himself thoroughly that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected. Hereafter throughout this manual, AOC Company will be referred to as AOC.
WARNING
Use of substitute replacement parts, which do not have the same, specified safety characteristics may create shock, fire, or other hazards. Under no circumstances should the original design be modified or altered without written permission from AOC. AOC assumes no liability, express or implied, arising out of any unauthorized modification of design. Servicer assumes all liability. FOR PRODUCTS CONTAINING LASER: DANGER-Invisible laser radiation when open. AVOID DIRECT EXPOSURE TO BEAM. CAUTION-Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. CAUTION -The use of optical instruments with this product will increase eye hazard. TO ENSURE THE CONTINUED RELIABILITY OF THIS PRODUCT, USE ONLY ORIGINAL MANUFACTURER'S REPLACEMENT PARTS, WHICH ARE LISTED WITH THEIR PART NUMBERS IN THE PARTS LIST SECTION OF THIS SERVICE MANUAL. Take care during handling the LCD module with backlight unit -Must mount the module using mounting holes arranged in four corners. -Do not press on the panel, edge of the frame strongly or electric shock as this will result in damage to the screen. -Do not scratch or press on the panel with any sharp objects, such as pencil or pen as this may result in damage to the panel. -Protect the module from the ESD as it may damage the electronic circuit (C-MOS). -Make certain that treatment persons body is grounded through wristband. -Do not leave the module in high temperature and in areas of high humidity for a long time. -Avoid contact with water as it may a short circuit within the module. -If the surface of panel becomes dirty, please wipe it off with a soft material. (Cleaning with a dirty or rough cloth may damage the panel.)
Dell E1909Wc
Max. Resolution
Plug & Play EPA ENERGY ON Mode STAR OFF Mode Input Connector
480i/480p/576i/576p/720p/1080i/1080p (Support HDCP) Operating Temp: 5 to 35C Operating Humidity: 10% to 80% Storage Temp.: -20 to 60C Weight with packaging: 13.54 lbs (6.14 kg)
Weight
Weight with stand assembly and cables: 10.27 lbs (4.66 kg) Weight without stand assembly: 7.80 lbs (3.54 kg) Weight of stand assembly: 2.23 lbs (1.01 kg)
Dell E1909Wc
The LCD monitor will contain a main board, power board, and a key board which house the flat panel control logic, The power board will provide AC to DC Inverter voltage to drive the backlight of panel and the main board chips each voltage.
CCFL Drive.
Power board
Main Board
Dell E1909Wc
Use the buttons on the front of the monitor to adjust the image settings.
Front panel Button A Menu B Brightness&Con trast /Adjust UP C Automatic Adjust /Adjust Down
Description Use the MENU button to launch the on-screen display (OSD) and select the OSD Menu.
Use this button to directly access the "Brightness/Contrast" menu or to increase the values of the selected menu option.
Use Auto Adjust to activate automatic setup/adjustment or to decrease the values of the selected menu option. The following dialog appears on a black screen as the monitor self-adjusts to the current input:
Auto Adjustment allows the monitor to self-adjust to the incoming video signal. After using Auto Adjustment, you can further tune your monitor by using the Pixel Clock (Coarse) and Phase (Fine) controls under Image Settings. D Use this button to select the input source or select an OSD menu option. Use the Input Source Select/Select Input source button to select one of the two different video signals that may be connected to your monitor: VGA input 7
Dell E1909Wc
< to image the for seconds 2 or 1 take may It source. input selected currently indicate messages following see will you inputs through cycle>
or
or
If either VGA or DVI-D input is selected and both VGA and DVI-D cables are not connected, a floating dialog box as shown below appears.
or
E Power indicator)
Use the Power button to turn the monitor on and off. The Blue LED indicates the monitor is on and fully functional. An amber LED
Dell E1909Wc
2.Push the
and
buttons to move between the setting options. As you move from one icon to another, the
option name is highlighted. See the following table for a complete list of all the options available for the monitor. 3.Push the 4.Push the 5.Push button once to activate the highlighted option. and buttons to select the desired parameter. or button, according to the indicators on the menu, to
make your changes 6.Press the Menu button once to return to the main menu to select another option or press the Menu button two or three times to exit from the OSD menu. The table below provides a list of all the OSD menu options and their functions.
Dell E1909Wc
Brightness
Push the
button
to decrease brightness (min 0 ~ max 100). Contrast Adjust Brightness first, and then adjust Contrast only if further adjustment is necessary.
Push the
button to
decrease contrast (min 0 ~ max 100). The Contrast function adjusts the degree of difference between darkness and lightness on the monitor screen. Auto Adjust Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use with your particular setup.
Input Source
Use the INPUT SOURCE menu to select between different video signals that may be connected to your monitor.
10
Dell E1909Wc
VGA
Select VGA input when you are using the analog (VGA) connector. Push
to select the VGA input source. DVI-D Select DVI-D input when you are using the Digital (DVI) connector. Push
to select the DVI input source. Color Settings Use the Color Settings to adjust the color setting mode and color temperature. There are different color setting sub-menus for VGA/DVI-D and Video input.
Choose the RGB option if monitor is connected to a PC or a DVD using a VGA or DVI cable. Choose the YPbPr option if monitor is connected to a DVD by a YPbPr to VGA or YPbPr to DVI cable or if the DVD color output setting is not RGB.
Mode Selection
You can choose Graphics or Video according to the input signal. Select Graphics if connecting a PC to your monitor; for connecting DVD, STB or VCR to your monitor, Video is recommended.
11
Dell E1909Wc
When you select Graphics, you can choose Standard, Multimedia, Game,
If you view media application like photo, clip etc via PC, choose "Multimedia" preset; If you play a game in PC, choose "Gaming" preset; If you prefer a lower color temperature (5700K), choose "Warm" preset; If you prefer a higher color temperature, choose "Cool" preset; Custom (R, G, B) Preset offers a range of 6500K colors; Choose "Standard" to utilize the panel native color format; Select Warm preset for a reddish tint. This color setting is used for color-intensive applications (photograph image editing, multimedia, movies, etc.)
Select Cool preset for a bluish tint. This color setting is used for text based applications (spreadsheets, programming, text editors, etc.) Select Custom preset to increase or decrease each of the three colors (R, G, B) independently, in single digit increments, from 0 to 100.
When you select Video, you can choose Movie, Game, Sports, or Nature preset: For playing a movie, choose "Movie" preset; For playing a sport program, choose "Sports" preset; For playing a game, choose "Game" preset; For general picture or web or watch TV, choose Nature preset. You can adjust the Hue(Tint)/Saturation based on your preference. If you want to restore default color settings, choose Color Reset; Select Color Reset preset to restore default (factory) Color settings. This setting is also the sRGB standard default color space. 12
Dell E1909Wc
Hue
This feature can shift color of video image to green or purple. This is used to
adjust the desired flesh tone color. Use from '0' to '100' .
or
to increase the green shade of the video image to decrease the purple shade of the video image
This feature can adjust the color saturation of the video image. Use
to adjust the saturation from '0' to '100'. to increase the monochrome appearance of the video image to decrease the colorful appearance of the video image
13
Dell E1909Wc
Horizontal Position Use the or buttons to adjust image left and right. Minimum is '0' (-). Maximum is '100' (+). Vertical Position Use the or buttons to adjust image up and down. Minimum is '0' (-). Maximum is '100' (+). Sharpness This feature can make the image look sharper or softer. Use
or Pixel Clock
The Phase and Pixel Clock adjustments allow you to adjust your monitor to your preference. These settings are accessed through the main OSD menu, by selecting 'Image Settings'.
or
If satisfactory results are not obtained using the Phase adjustment, use the Pixel Clock (coarse) adjustment and then use Phase (fine), again.
Select this option to adjust the settings of the OSD, such as, the languages of the OSD, the amount of time the menu remains on screen, and so on.
14
Dell E1909Wc
Language
Language option to set the OSD display to one of seven languages (English, Espanol, Francais, Deutsch, Portugues,Simplified chinese or Japanese).
or Menu Timer
OSD Hold Time: Sets the length of time the OSD will remain active after the last time you pressed a button.
Use the
or
increments, from 5 to 60 seconds. Menu Lock Controls user access to adjustments. When 'Lock' is selected, no user adjustments are allowed. All buttons are locked except the menu DDC/CI button.
DDC/CI (Display Data Channel/Command Interface) allows your monitor parameters (brightness, color balance etc) to be adjustable via software on your PC. You can disable this feature by selecting "Disable". Enable this feature for best user experience and optimum performance of your monitor.
15
Dell E1909Wc
Helps reduce minor cases of image retention. Depending on the degree of image retention, the program may take some time to run. You can enable this feature by selecting "Enable".
Factory Reset Reset all OSD settings to the factory preset values.
16
Dell E1909Wc
DVI Connector:
6 7 8
17
Dell E1909Wc
18
Dell E1909Wc
The display supports the WXGA+(1440(H)X900(V))screen format and 16.7M clors.All input signal are 2 signal LVDS interface compatible This module does not contain an inverter card for backlight.
19
Dell E1909Wc
Ta= 25C, VLCD=5.0V, fV=60Hz fCLK=54MHz, IBL=7.5mA
20
Dell E1909Wc
21
Dell E1909Wc
22
Dell E1909Wc
23
Dell E1909Wc
24
Dell E1909Wc
2 N 4
5 Y 6
N Y
10 Y N 12 Y 14
11
13 Y 15 Y 17
16
18
19 Y 25
Dell E1909Wc
9) Save the power key status into EEprom. Turn on the LED and set it to green color. Scalar initializes. 10) In standby mode? 11) Update the lifetime of back light. 12) Check the analog port, are there any signals coming? 13) Does the scalar send out an interrupt request? 14) Wake up the scalar. 15) Are there any signals coming from analog port? 16) Display "No connection Check Signal Cable" message. And go into standby mode after the message disappears. 17) Program the scalar to be able to show the coming mode. 18) Process the OSD display. 19) Read the keyboard. Is the power key pressed?
26
Dell E1909Wc
EEPROM M24C16 (U403) Scalar TSUM5PEHL-LF-2 (Include MCU, ADC, OSD) (U401)
RXD TXD
R G B D-Sub
H V
Connector (CN101) Digital video signal DVI Connector (CN102) DDC_SCL_DVI, DDC_SDA_DVI EEPROM M24C02 (U103)
27
Dell E1909Wc
CN902 5V
12V ON/OFF Rectify and Lamp Output Over Voltage Protect DC Convert Circuit PWM Control IC MOSFET
Feedback Circuit
28
Dell E1909Wc
Remove stand Button Press the buttonat the same time pull out the hinge cover follow the arrowhead direction and remove it, then remove the hinge.
rear cover: 1.Remove the two screws and remove the base by Torque A.
29
Dell E1909Wc
2.Pry the monitor up then find out the hooks position, use the tool (like the picture or other card) to insert into the gap of bezel and rear cover, then turn over the monitor and take off the rear cover.
Remove the key board Remove the screws remarked in red by KEPC cable Torque B or by manual
30
Dell E1909Wc
Remove shield: 1.Remove the screws remarked in red by Torque B or by manual and disconnect connector remarked in green.
2.Remove the four screws and remove the main frame by manual or torque = 3kgF.Cm
3. Remove the main frame and at the same time disconnect the LVDS connector and remove the EVA washers. Install: Note: Make LVDS connectors metal side adown
31
Dell E1909Wc
Remove the Power Board, Main Board: Remove the screws remarked in red by Torque B or by manual and disconnect connector remarked in green.
32
Dell E1909Wc
The panel
33
Dell E1909Wc
DSUB_B+
DSUB_H DSUB_V
2 2
D109 BAT54C
DSUB_B-
DSUB_SOG DSUB_G+
2 2
DDC1_SCL
DDC1_SCL
DSUB_SCL 15 14 13 DSUB_SDA 12 11
VGA_PLUG DSUB_5V VGA_BVGA_B+ ZD104 VGA_G- RLZ5.6B VGA_G+ VGA_RVGA_R+ C124 0.1uF 16V ZD105 RLZ5.6B VGA_G+ VGA_R+ 1 2 3
FOR EMI
U10 3
DSUB_G-
FB101 BEAD 2 R116 75R 1/16W 5% VGA_RR115 100R 1/16W 5%C111 0.047uF DSUB_R+ 2
U10 1
DVI_5V
CN102 VSY NC SY NC GND DDC SCL DDC SDA +5V HPD 1/3shield 2/4shield 0/5shield clk shield DAT0+ DAT0DAT1+ DAT1DAT2+ DAT2DAT3+ DAT3DAT4+ DAT4DAT5+ DAT5clk+ clk8 15 6 7 14 16 11 3 19 22 18 17 10 9 2 1 13 12 5 4 21 20 23 24 DVI_HPD DVI_5V FB109 R120 10K 1/16W 5% 300 OHM C115 0.1uF/16V R126 R127 R128 R129 R130 R131 10R 10R 10R 10R 10R 10R 1/16W 1/16W 1/16W 1/16W 1/16W 1/16W 5% 5% 5% 5% 5% 5% RX0P RX0N RX1P RX1N RX2P RX2N R118 100R 1/16W 5% R119 100R 1/16W 5% DDC2_SCL DDC2_SDA DDC2_SCL DDC2_SDA 2 2
D104 BAT54C
R140 NC R122 NC R121 NC R123 C116 10K 1/16W 5% 0.22uF R125 U101 4K7 1/16W 5% 8 1 7 VCC A0 2 A1 3 6 WP SCL A2 5 4 SDA VSS M24C02-WMN6TP CMVCC FB104 FB105 DVI_5V 3 HDCP_CTRL 2 Q101 NC R124 4K7 1/16W 5% DDC1_SCL DDC1_SDA 2 DDC_WP
2 2 2 2 2 2
26 25
JACK
GND GND
R132 R134
RXCP RXCN
2 2
D108 BAT54C
300 OHM
C122 1000pF
1 2 3
ESD_VCC 6 5 4 C120 NC 1 2 3
ESD_VCC 6 5 4 C118 NC 1 2 3
ESD_VCC 6 5 4 C119 NC
R133 10K 1/16W 5% DVI_HPD R135 10K 1/16W 5% 6K8 1/16W 5% DET_CABLE 2 R137 4K7 1/16W 5% DDC2_SCL DDC2_SDA 2 DDC_WP R138 4K7 1/16W 5%
C117 0.22uF 1 2 3 4
VGA_PLUG R139
U1 07
GND POWER DGND
U1 05
U1 06
M24C02-WMN6TP T P V ( Top
Key Component
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL NEW Q SERIES TPV MODEL PCB NAME Sheet 2 of 6 17W~22W
Size Rev
B D <>
Date
34
Dell E1909Wc
CN301
1 2 3 4
U301 S S S G D D D D
8 7 6 5 PANEL_VCC
C303 NC
Q301 AO3401
NC\AO4411
PPWR_ON#
Q302 2N3906S-RTK/PS
C304 NC R305
C301 0.1uF/16V
CONN
3D 1 G AO3401L 2 S
+ C305 100uF25V
T P V ( Top
Key Component
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL NEW Q SERIES TPV MODEL PCB NAME Sheet 3 of 6 17W~22W
Size Rev
A D <>
Date
35
Dell E1909Wc
CN701 1 2 3 4 5 6
C705 CMVCC CMVCC BKLT-VBRI BKLT-EN SM340A D701 MVCC Q702 KN2907AS 0.1uF/16V
+ C704 100uF/25V
VCC3.3
R705 10K 1/16W 5% Q703 KN2907AS BKLT-VBRI VCC3.3 R706 adj_BACKLIGHT 2 1K 1/16W 5%
R708 NC
lock type
DGND 1,2,3
VCTRL
D702
VCC3.3 VCC3.3 MVCC R703 10K 1/16W 5% MVCC on_BACKLIGHT 2 Q701 4K7 1/16W 5% 2N3904S-RTK/PS + C706 100uF/25V C708 0.1uF/16V FB703 300 OHM C711 0.1uF 16V U701 3 VIN VSS VOUT 2 C707 C709 0.1uF/16V + 100uF/25V
NC BAT54C
R701
NC VCC3.3
0R05 1/4W NC NC
AP1117E33LA 1
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL NEW Q SERIES TPV MODEL PCB NAME Sheet 4 of 6 17W~22W
Size Rev
B D <>
Date
36
Dell E1909Wc
Del C209 10uF/50V
0.1uF/16V 0.1uF/16V
8 14
98
16
24
32 49 56 75
51 66 82
34
VCC3.3 FB404 VCTRL LVA3P LVA3M LVACKP LVACKM LVA2P LVA2M LVA1P LVA1M LVA0P LVA0M 81 54 55 58 59 60 61 62 63 64 65 PA0 PA1 PA2 PA3 PA4 PA5 PA6 PA7 PA8 PA9 VCTRL 300OHM
VMPLL VCC3.3 VDVI R403 0 OHM +-5% 1/8W C414 0.1uF/16V C415 0.1uF/16V
AVDD_MPLL
AVDD_PLL
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
DSUB_R+ DSUB_RDSUB_G+ DSUB_GDSUB_SOG DSUB_B+ DSUB_BDSUB_H DSUB_V DDC1_SDA DDC1_SCL RX2P RX2N RX1P RX1N RX0P RX0N RXCP RXCN DDC2_SDA DDC2_SCL
23 22 20 19 21 18 17 27 28 30 31 3 4 6 7 9 10 12 13 100 1
RIN0P RIN0M GIN0P GIN0M SOGIN0 BIN0P BIN0M HSY NC0 VSY NC0 DDCA_SDA/RS232_TX DDCA_SCL/rs232_RX R+ RG+ GB+ BCK+ CKDDCD_SDA DDCD_SCL
AVDD_ADC
AVDD_DVI AVDD_DVI
VDDC
C413 0.1uF/16V
PA[0..9] 67 68 69 70 71 72 73 74 77 78 36 45 46 41 42 35 47 85 86 87 88 89 90 91 92 93 94 95 99 R415 R416 R417 R419 R420 100R 1/16W 5% 100R 1/16W 5% 100R 1/16W 5% 56 OHM 1/16W 120R 1/16W 5% KEY 1 KEY 2 R409 100R 1/16W 5% EE_WP PB0 PB1 PB2 PB3 PB4 PB5 PB6 PB7 PB8 PB9 PB[0..9]
PA[0..9] PB[0..9]
3 3
AVDD
TSUM5PEHL-LF-2
LVB3P LVB3M LVBCKP LVBCKM LVB2P LVB2M LVB1P LVB1M LVB0P LVB0M NC NC NC GPIO_P23 GPIO_P22
NC
VCC3.3
Internal EDID
CMVCC
External EDID 22K 1/16W 5% 10K 1/16W 5% 0.1uF/16V 2N3904S-RTK/PS 10K 1/16W 5% 10K 1/16W 5%
NC NC NC NC NC NC
C401 0.22uF16V R412 10K 1/16W 5% WP 1 2 3 4 U402 CE# VDD SO HOLD# WP# SCK VSS SI 8 7 6 5 37 38 39 40 48 84 R421 100K 1/16W 5% C420 47pF SDO SCZ SCK SDI GPIO_P27/PWM1 RST
LVDS
GPIO_P15/PWM0 PWM2/GPIO_P24 GPIO_P12 PWM1/GPIO_P25 RSTN GPIO_P00/SAR1 GPIO_P01/SAR2 GPIO_P02/SAR3 GPIO_P06 GPIO_P07 PWM0/GPIO_P26 GPIO_P13 GPIO_P14 GPIO_P16/PWM2
WP on_BACKLIGHT 4 adj_BACKLIGHT 4
SST25LF020A-33-4C-SAE 3 PPWR_ON# C419 MVCC + 10uF/50V R423 0R05 1/16W X401 14.31818MHz
C418 0.1uF/16V
96
XIN
R425
100R 1/16W 5%
C421 47pF
XOUT
BY PASS GPIO_P10/I2C_MCL GPIO_P11/I2C_MDA GND GND GND GND GND GND GND GND GND GND 44 43 R429 R431 100R 1/16W 5% 100R 1/16W 5% MSCL MSDA POWER_KEY # KEY 1 KEY _RIGHT R437 KEY 2 R439 KEY _Source KEY _Menu KEY _LEFT 2K OHM 1/16W 2K OHM 1/16W LED_GRN/BLUE 2 4 6 8 CONN
52 53
MODE[0] MODE[1]
2 5 11 29 33 50 57 76 79 83
FFC CONNECTOR
CN401CN402LAY
C423 0.22uF16V
24LC16B/SNG
KEY 2 KEY 1 POWER_KEY # LED_GRN/BLUE LED_ORANGE C431 0.1uF/16V C432 0.1uF/16V C433 0.1uF/16V C434 0.1uF/16V R411 10K 1/16W 5% C435 0.1uF/16V R408 10K 1/16W 5%
T P V ( Top
Key Component
Victory
Electronics
Co . ,
Ltd. )
OEM MODEL NEW Q SERIES TPV MODEL PCB NAME Sheet 5 of 6 17W~22W
Size Rev
C D <>
Date
37
Dell E1909Wc
+12V 2 ZD902 RLZ16B R921 100 OHM 2W R929 1K 1/8W C931 1uF 1 2 ZD901 NC Q902 KTD1028 C910 1000pF 1
BD901
R908 100K 2W 5
7 R935 100 1/4W C929 0.001uF L903 1.1uH C915 470uF/16V D907 31DQ06FC3 + C939 1000uF/25V R924 180R 1/10W 5% 2 +
!
R933 300K OHM 1/4W R932 300K OHM 1/4W + C908 22uF/50V 5 6 7 8 2
6 1
+5V
C916 0.47uF
!
2
FG
L902 1
2 ZD903 RLZ22B
E BAW56
IC901 LD7552BPS
Q901 STP10NK70ZFP
C902 0.001uF/250V
C901 0.001uF/250V
4 3 2 1
FB901 BEAD
D903
12
ZD921 RLZ16B IC903 PC123X2Y FZOF R925 1K 1/10W 1% D915 LL4148 C924 0.1uF/25V 1 1
ZD922 RLZ5.1B
C907 0.1uF 1
4 30mH
ZD904 RLZ22B
D916 LL4148
C909 470pF/25V
R926 1K 1/10W 1%
R942 1K 1/10W 1%
C928 0.001uF
C921 0.0047UF/400V
+5V
CN902 CONNECTOR
1uF
DIM
FG
SOCKET 2 3 ON/OFF 1 GND1 GND 1 2 Title PWPC8942MY A1 FOR DELL 19 POWER CIRCUIT Size B Date: Document Number G2853-1-2-X-3-080703 Thursday , July 03, 2008 Sheet 1 of 2 Rev 1
CN901
!
FG
38
Dell E1909Wc
HV LV CN801 CONN
!
C801 10pF/6KV
!
5 6 7 8 C839 1000pF 1 2 R828 10K 1/10W R822 1K 1/10W 1% 2 C841 1000pF R858 33 1/4W T802 8 POWER X'FMR C823 0.0022uF 3 1 R814 1K5 1/10W 1% C811 10pF/6KV 9 D802 BAV99 HV LV CN802 CONN
4 3 2 1
Q811 PMBS3904
1 2 4 3 5 6 7
Vref
Q812 PMBS3906 1
C803 470uF/25V +
C805 0.1uF
R857 33 1/4W
!
B 3 C E
1 D808 BAW56 2 R834 10K 1/10W R812 1K 1/10W 1% 2 C816 0.0022uF 3 1 R816 1K5 1/10W 1% D804 BAV99
1 2
HV LV CN804 CONN
!
Q803 AO4828L 4 3 2 1 G1 S1 G2 S2 D1 D1 D2 D2 5 6 7 8 3 C840 1000pF
Q806 PMBS3904
1 2 R833 10K 1/10W R809 1K 1/10W 1% 2 C815 0.0022uF 3 1 R815 1K5 1/10W 1% D803 BAV99
HV LV CN803 CONN
D809 LL4148
R802 NC
C842 0.01uF
C822 1uF/25V
IC801 1IN+ 2IN+ 1IN2INFEEDBACK REF DTC OUTPUT CTRL CT VCC RT C2 GND E2 C1 E1 TL494IDR 16 15 14 13 12 11 10 9
D814 LL4148
R818 1K 1/10W 1%
D806 LL4148
C821 0.1uF/25V
R854 68K 1% 1/10W R807 47K 1/10W R826 1K 1/10W 1% R824 1K 1/10W 1%
Q809 RK7002
C820 220pF
C817 NC
C834 0.1uF/25V
R835 1M 1/10W 5%
Title PWPC8942MY A1 FOR DELL 19POWER CIRCUIT Size Document Number Custom G2853-1-2-X-3-080703 Date: Thursday , July 03, 2008 Sheet 2 of 2 Rev 1
39
Dell E1909Wc
CONN
10SW
MENU
LED
GND
Key Board
715G2801-B-2
Sheet 1 of
Rev A 1
40
Dell E1909Wc
41
Dell E1909Wc
42
Dell E1909Wc
43
Dell E1909Wc
44
Dell E1909Wc
No power
Press power key and look if the picture is normal OK Please reinsert and make sure the AC of 100-240 is normal OK Measure U701 PIN2=3.3V C904(+)=1.8V OK NG Check CN701 or replace U701, Q702,Q703 NG Reinsert or check the Adapter/Inverter section
Replace X401
Check U401
45
Dell E1909Wc
No picture
NG
NG
Replace X401
OK Check reset circuit of U401s normal Measure U701 PIN2=3.3V C904(+)=1.8V OK NG OK Replace U401 NG Check Correspondent component
Replace X401
Replace U401
46
Dell E1909Wc
White screen
NG
OK
NG
Replace X401
Replace PANEL
Replace U401
47
Dell E1909Wc
OK
NG
Check AC input
Check the voltage of C905(+) NG OK Check bridge rectified circuit and F901 circut
Check start voltage for the pin8 of IC901 NG OK Check R904,R932,R933 and Change IC901
Check the auxiliary voltage is bigger than 10V and smaller than 20V NG OK 1) Check IC901 2) Check IC901 over current protect circuit
48
Dell E1909Wc
NG OK
Check IC801 PIN10, 9 have the output of square wave at short time NG Change IC801 OK Check Q803,Q802 PIN5, 6, 7, 8 have the output of square wave at short time. NG Check Q802, Q803,Q801, Q804, Q811 ,Q812, OK
49
Dell E1909Wc
50
Dell E1909Wc
51
Dell E1909Wc
b. The Minimum brightness is < 40% of Max luminance (max luminance = max contrast + max brightness) Test conditions: Set <Brightness> Brightness, Contrast to the min.
52
Dell E1909Wc
(5). Update the firmware Step 1: Double click the ISP_Tool v3.772.exe icon and click Connect, bring up Fig.2
Fig.2
53
Dell E1909Wc
Fig.3
54
Dell E1909Wc
Fig.4
Fig.5
55
Dell E1909Wc
Fig.6 Step 5: When appear Verify OK, writer finished as shown Fig.7
Fig.7
56
Dell E1909Wc
E
57
Dell E1909Wc
Remark
052G6019 1 052G6022 1500 070GHDCP500HDC E08902 E08902 E08902 E08903 E08903 E08907 089G 728CAA 2D 089G 728GAA 2D 089G 728LAA 2D 089G1748GAA 1D 089G1748LAA 1D 089G179E30N513 089G402A18NYHD 0M1G 130 6120 0M1G 330 5120 0M1G1730 6120 0M1G2940 10225 CR3 705GQ815009 019G 588 3 0M1G 130 6120 Q15G0289201 Q15G0290201 Q15G0341101 Q20G6044101 E750 E750 750GLU90W1022Z000D 750GLU90W1032Z000D 756GQ8CB DL00A U402 SMTC-U402 056G1133 81 100GDMA9000NT1 A33G0392 VH 1X0100 040G 45762412B CN701 CN701 CN701 033G3802 6B Y 033G3802 6B Y 033G3802 6B Y
2nd source
2nd source
2nd source
Dell E1909Wc
033G801930F CH JS 067G 3151007KV 067G 3151014KV 067G215V100 7N 067G215V101 4N 067G215V101 4N 067G215V101 4N 088G 35315F H 088G 35315F HJ 088G 35424F J 088G 35424F N 093G 22 53 J 056G 562570 056G 662 13 056G 662 13 056G 662 13 056G 662 13 056G 662 13 056G1133 34 056G1133 34 056G1133 81 056G113356A 056T 585 4A 057G 417 12 T 057G 417 12 T 057G 417 13 T 057G 417 22 T 057G 417 22 T 057G 763 1 061G0402000 061G0402100 061G0402100 061G0402100 061G0402100 061G0402100 061G0402100 061G0402100 061G0402100
Dell E1909Wc
Dell E1909Wc
Dell E1909Wc
Dell E1909Wc
Dell E1909Wc
056G 139 3A 056G 139 5A 061G 58080 WT 061G152M104 64 063G107K224 UM 063G107K474 6S 065G 6J1006ET 065G 6J1006ET 065G305M1022BP 065G305M1022BP 065G306M4722BP 067G215D4714KV 067G215D4714KV 067G215D6814KV 067G215D6814KV 067G215S10115N 067G215S4713KV 067G215V102 4N 073G 174 65 S2 073G 253191 S 073G 253191 S 080GL19T 24 H 080GL19T 24 H 080GL19T501 N 087G 50132B DL 093G 50460 28 093G3006 1 1 095G 825 9E513 095G 825 9X513 705GQ857008 051G 200 1
EC 1000UF 25V KY25VB1000M-CC3 12.5*20MM LINE FILTER 30MH MIN IND CHOKE 1.1UH IND CHOKE 1.1UH XFMR INVERTER 740MH DADON XFMR INVERTER 740MH DADON XFMR POWER 650UH+-5% YUVA AC SOCKET BRIDGE DIODE KBP208G LITEON 31DQ06FC3 NIHON INTER WIRE HARNESS 9P(SCN)-6P(PLUG) WIRE HARNESS 9P(SCN)-6P(PLUG) Q901 ASS'Y OIL FOR DISAPPEAR STP10NK70ZFP SCREW HEAT SINK D906 ASS'Y OIL FOR DISAPPEAR FMEN210A TO-220 SANKEN 64 2nd source
Q901
D906
093G 60500
Dell E1909Wc
Dell E1909Wc
RST CHIPR 3.6K OHM +-1% 1/10W RST CHIPR 3.6K OHM +-1% 1/10W RST CHIPR 3.6 KOHM +-5% 1/10W RST CHIPR 3.6 KOHM +-5% 1/10W RST CHIPR 47 KOHM +-1% 1/10W RST CHIPR 560 KOHM +-5% 1/10W RST CHIPR 68K RST CHIPR 68K RST CHIPR 68K RST CHIPR 68K RST CHIPR 68K OHM +-1% 1/10W OHM +-1% 1/10W OHM +-1% 1/10W OHM +-1% 1/10W OHM +-1% 1/10W
RST CHIPR 91 KOHM +-5% 1/10W RST CHIPR 9.31 KOHM +-1% 1/10W 10 OHM 1/10W 10 OHM 1/10W RST CHIPR 100KOHM +-1% 1/8W 1ST CHIPR 100 RST CHIPR 1K OHM +-5% 1/8W OHM +-5% 1/8W
RST CHIPR 10K OHM +-5% 1/8W RST CHIPR 220 OHM +-5% 1/8W RST CHIPR 33 OHM +-5% 1/8W RST CHIPR 33 OHM +-5% 1/8W RST CHIPR 47K OHM +-5% 1/8W RST CHIPR 51K OHM +-1% 1/8W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W RST CHIPR 0 OHM +-5% 1/4W 66
Dell E1909Wc
RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 100 OHM +-5% 1/4W RST CHIPR 300K OHM +-5% 1/4W RST CHIPR 300K OHM +-5% 1/4W RST CHIPR 300K OHM +-5% 1/4W RST CHIPR 33 OHM +-5% 1/4W RST CHIPR 33 OHM +-5% 1/4W RST CHIPR 33 OHM +-5% 1/4W RST CHIPR 33 OHM +-5% 1/4W RST CHIPR 510 KOHM +-5% 1/4W RST CHIPR 510 KOHM +-5% 1/4W RST CHIPR 510 KOHM +-5% 1/4W RST CHIPR 620 KOHM +-5% 1/4W RST CHIPR 620 KOHM +-5% 1/4W RST CHIPR 620 KOHM +-5% 1/4W CHIP 0.01UF 16V X7R CAP CHIP 0603 0.1UF K 25V X7R CAP CHIP 0603 0.1UF K 25V X7R CAP CHIP 0603 0.1UF K 25V X7R CAP CHIP 0603 0.1UF K 25V X7R CAP CHIP 0603 0.1UF K 25V X7R CHIP 2200PF 25V X7R CHIP 2200PF 25V X7R CHIP 2200PF 25V X7R CHIP 2200PF 25V X7R CAP CHIP 0805 1000PF J 50V NPO CAP CHIP 0805 1000PF J 50V NPO CAP CHIP 0805 1000PF J 50V NPO CAP CHIP 0805 1000PF J 50V NPO CHIP 1000P 50VX7R 0805 CHIP 1000P 50VX7R 0805 67
Dell E1909Wc
Dell E1909Wc
Q52G6020117 Q52G6025 13140 Q70G9002700 1A Q85G0098101 E08907 S89G179T30N513 089F80001703AG 033F303FH10BK3 033F303FJSHK30 Q40G 19N70010A Q40G0001700 4A
69
Dell E1909Wc
Remark
Diversity of T9RSMAHKX5DFHN compared with T9RAMAHKX5DFHN Location Part No. 705GQ815010 Q15G0341201 E750 E750 750GLS90M3172Z000D 750GLS90M31CCZ000D 756GQ8CB DL00S SMTC-U402 100GDMS9000N11 PWPC8942SYA1 R861 061G0603270 3F Q34G0412 VH 3S0130 Description MAIN FRAME ASS'Y 19W MAINFRAME PANEL LTM190M2-L31 CLD(5TS) SZ SEC PANEL LTM190M2-L31 CTN(5TZ) FQ SEC MAIN BOARD-CBPCRMADEQ1 MCU ASSY-056G1133 81 POWER BOARD G2853-1-2-X-2-080703 RST CHIPR 270KOHM +-1% 1/10W REAR COVER 19W 2nd source Remark
Diversity of T9RSMAHKX5DFHC compared with T9RAMAHKX5DFHN Location Part No. 705GQ815010 Q15G0341201 E750 E750 750GLS90M3172D000D 750GLS90M31CCD000D 756GQ8CB DL00S SMTC-U402 100GDMS9000N11 PWPC8942SYA1 R861 061G0603270 3F Q34G0412 VH 3S0130 Description MAIN FRAME ASS'Y 19W MAINFRAME PANEL LTM190M2-L31 CLD(5TS6) SZ SEC PANEL LTM190M2-L31 CTN(5TZ7) FQ SEC MAIN BOARD-CBPCRMADEQ1 MCU ASSY-056G1133 81 POWER BOARD G2853-1-2-X-2-080703 RST CHIPR 270KOHM +-1% 1/10W REAR COVER 19W 2nd source Remark
70
Dell E1909Wc
Remark
Diversity of T9RAMAHKX5DFHC compared with T9RAMAHKX5DFHN Location E750 E750 Part No. 750GLU90W1022D000D 750GLU90W1032D000D Description PANEL M190PW01 V00A SZ AUO PANEL M190PW01 V00B SZ AUO 2nd source Remark
Diversity of T7RCMEHJFDDFNC compared with T9RAMAHKX5DFHN Location Part No. 044G9003210 089G401A18NHRA 705GQ715020 M015 M015 E750L E750L Q15G0250 3 SQ15G02503 750GLC170A7H13D0DL 750GLC170A7H23D0DL 756GQ8CB DL004 SMTC-U402 100GDMC7000N11 Q07G 1 5D35 X Description CORNER PAPER POWER CORD MAIN FRAME ASS'Y 17 DELL E178FPc Mainframe MAIN FRAME PANEL CLAA170EA07HS 7H4 FZ CPT PANEL CLAA170EA07HS 7J4 FZ CPT MAIN BOARD-CBPCRMADEQ1 MCU ASSY-056G1133 81 WOODEN PALLET RATING LABEL E178FP PIG FOR JA 2nd source Remark
71