Académique Documents
Professionnel Documents
Culture Documents
Ujian 1 : / 10%
Ujian 2 : / 10%
Tugasan 1 : /10%
Tugasan 2 : /10%
Tugasan 3 : /15%
Ujian Akhir : /40%
Kehadiran :
JUMLAH /100%
Command: ZOOM
ZOOM
Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: ALL
Regenerating model.
Memaparkan keamatan skala
Command: GRID
Command: LINE
Specify first point: 70,70
@160,0 bermaksud titik kedua
adalah 160 unit kekanan paksi x
Specify next point or [Undo]: @160,0 dari titik awal (koordinat 70,70)
dan 0 unit pada paksi Y.
Specify next point or [Undo]: @0,90 Dimana paksi Y tidak berganjak
Command: LINE
Specify first point: 90,90
@120<0
Specify next point or [Undo]: @120<0 @120 adalah jarak lurus dari titik
awal
Specify next point or [Undo]: @50<90 <0 merujuk kepada arah 00 iaitu arah
kekanan
Specify next point or [Close/Undo]: @120<180 Perhatikan rajah dibawah
Command: LINE
Specify first point: 100,100
1800 00
Specify next point or [Undo]: @100<0
Command: LINE
Specify first point: 110,110
3D SOLID EDITING
Arahan EXTRUDE dan UNION
Command:
Command: limits
Reset Model space limits:
Specify lower left corner or [ON/OFF] <0.0000,0.0000>: 0,0
Specify upper right corner <420.0000,297.0000>: 297,210
Command: z
ZOOM
Specify corner of window, enter a scale factor (nX or nXP), or
[All/Center/Dynamic/Extents/Previous/Scale/Window] <real time>: all
Regenerating model.
Command: pline
Specify start point: 0,0,0
Current line-width is 0.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @80<0
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @20<90
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: 20,80
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @20<180
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @80<-90
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]:
Command: extrude
Current wire frame density: ISOLINES=4
Select objects: last
1 found
Select objects:
Specify height of extrusion or [Path]: -20
Specify angle of taper for extrusion <0>:0
Command: pline
Specify start point: 0,0,0
Current line-width is 0.0000
Specify next point or [Arc/Halfwidth/Length/Undo/Width]: @80<0
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @80<90
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @80<180
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]: @80<-90
Specify next point or [Arc/Close/Halfwidth/Length/Undo/Width]:
Command: m
MOVE
Select objects: last
1 found
Select objects:
Specify base point or displacement: 0,0,0
Specify second point of displacement or <use first point as displacement>:
0,0,-20
Command: extrude
Current wire frame density: ISOLINES=4
Select objects: last
1 found
Select objects:
Nota Pelajar Disediakan Oleh:
TKP2314(CAD/CAM/CAE for Prodoction) Naziran Khalis Omar
TKM JMTi Sebuah KEJAYAAN terhasil daripada USAHA yang berterusan dengan penuh KESABARAN
Command: CIRCLE
CIRCLE Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 100,100
Specify radius of circle or [Diameter]: 90
Command: EXTRUDE
Current wire frame density: ISOLINES=4
Select objects: LAST
1 found
Select objects:
Specify height of extrusion or [Path]: -30
Specify angle of taper for extrusion <0>:
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 100,170
Specify radius of circle or [Diameter] <90.0000>: 10
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 170,100
Specify radius of circle or [Diameter] <10.0000>: 10
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 100,30
Specify radius of circle or [Diameter] <10.0000>: 10
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 30,100
Specify radius of circle or [Diameter] <10.0000>: 10
Nota Pelajar Disediakan Oleh:
TKP2314(CAD/CAM/CAE for Prodoction) Naziran Khalis Omar
TKM JMTi Sebuah KEJAYAAN terhasil daripada USAHA yang berterusan dengan penuh KESABARAN
Command: EXTRUDE
Current wire frame density: ISOLINES=4
Select objects: ALL
5 found
Select objects: REMOVE
Remove objects: 100,190
1 found, 1 removed, 4 total
Remove objects:
Specify height of extrusion or [Path]: -10
Specify angle of taper for extrusion <0>:
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 100,100
Specify radius of circle or [Diameter] <10.0000>: 40
Command: EXTRUDE
Current wire frame density: ISOLINES=4
Select objects: LAST
1 found
Select objects:
Specify height of extrusion or [Path]: -30
Command: SHADE
Command: <Grid off>
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: <Snap on>
<Grid on> <Coords on> <Grid off> 100,100
Command: EXTRUDE
Select objects:
Command: POLYGON
Enter number of sides <4>: 6
Command: EXTRUDE
Select objects:
Command: MOVE
MOVE
Select objects: LAST
1 found
Select objects:
Specify base point or displacement: 0,0,0
Specify second point of displacement or <use first point as displacement>:
0,0,-15
Command: COPY
Select objects:
Specify base point or displacement, or [Multiple]: 0,0,0
Nota Pelajar Disediakan Oleh:
TKP2314(CAD/CAM/CAE for Prodoction) Naziran Khalis Omar
TKM JMTi Sebuah KEJAYAAN terhasil daripada USAHA yang berterusan dengan penuh KESABARAN
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 100,100,-105
Command: EXTRUDE
Select objects:
Command: CIRCLE
Specify center point for circle or [3P/2P/Ttr (tan tan radius)]: 100,100,-135
Command: EXTRUDE
Select objects:
Command: VPOINT
Command: SHADE