Vous êtes sur la page 1sur 25

ELEC166 on Mac

Chapter 1
Basics of Electricity 1.1 Static Electricity. Atoms and Electrons

You have probably all noted some of the peculiar phenomena - crackling and hair on end which may occur when dry hair is combed. Such phenomena were noticed centuries ago (before plastic combs were invented), for example when amber was rubbed with a cloth. The Greek word for amber was electron - and hence words were coined such as electric and electronic to describe these and related phenomena. For much of the time until the last century, it was considered that electricity was some kind of fluid. Observations such as transfer of electricity from one object to another seemed to support this idea, It was also thought that this fluid could be present in arbitrarily small quantities. Likewise it was thought that all substances can be divided into arbitrarily small parts. It turned out that there is a limit to this division and so the atomic theory was conceived. Atomic theory - which says that matter is made up of very small objects called atoms - also provides insight into the nature of electricity. We will review here its key concepts. Atomic theory (at its simplest) describes atoms as made up of three different components. In the centre of an atom there is a small and dense nucleus , made up of protons and neutrons. There is normally quite a few of them, and the number of protons is roughly similar to that of neutrons. Substances are made up of various atoms, which differ in their number of protons1. An important point for us is that the proton has a special property called charge. Charge is a basic quantity underpinning all electrical phenomena. Charge in a proton is conventionally denoted as positive, and as a result the nucleus is positively charged. In addition to protons and neutrons, an atom has electrons. The number of electrons in atoms is equal to the number of protons2. Electrons are lighter than protons, and also have the property of charge, which is negative and equal to that of a proton. Electrons hover near the atomic nucleus, being attracted to positive charge (Figure 1.1). They remain quite close to the nucleus, so that a typical atom is about 10-10 m across and, as a whole, has a net charge of zero. This is because the number of protons is equal to the number of electrons, and they have opposite charge.

1 Protons and neutrons are small, they have the same mass, about 1.7 x 10-27 kg, and

their size is about 10-15 m .


2 The numbers of protons and electrons in atoms are equal if atoms have not been

tampered with. Later we describe how to make these numbers unequal.


1.1

ELEC166 on Mac

We know now that in many substances, such as for example amber, plastics or metals, it is possible to make some electrons either part with their parent atoms for good, or at least move to a considerable distance. This can be done by friction (very effective for amber, synthetic fibres etc.), or exposing atoms to light (practically used in photocopying machine), or attaching the ends to a battery. In all these cases electrons are made to go away, or move, thus leading to movement of charge. Positively charged nuclei in atoms are heavier, and firmly stuck in the substance, and they do not move. As a result we have a net separation of charge - negative electrons go one way, leaving positive charge behind. At this point we notice that electrical phenomena start to set in. Usually some electrons leave the substance or the object, while an equal amount of electrons flows to the object from the other end, so the object retain its net zero charge. Movement of charges is very important in technology; later we will call this movement a current. We now reiterate what we just learned. Electricity has to do with electrons, which are all identical and have a property called electron charge that is, by definition, negative. Larger bodies can also have charge, either negative or positive. Negatively charged bodies have an excess of electrons compared to uncharged bodies. These electrons could have been transferred intentionally from another charged body, or in the process of a natural phenomenon, such as lightning strike, friction etc. Objects can also be positively charged, in which case some of their electrons are missing. This once again can arise through friction, charge transfer, etc. Negative charges are capable of cancelling or neutralising positive charges, if present in adequate numbers (and the other way round). The degree to which a body is charged can be specified by giving the number of excess (or missing) electrons. This is not a very convenient quantity, as a single electron charge is very small. The charge of a single electron qe is qe = 1.6 x 10-19 C (Coulomb) Since the discovery of electricity, a number of useful devices and appliances have been invented that changed our lives forever. They mostly involve moving charges (currents).
1.2

ELEC166 on Mac

Applications of static charges remain quite rare; the most familiar one is in the photocopying machine. Inside, a special drum made of the element selenium acquires a pattern of positive charge that corresponds to the original pattern - by being exposed to light reflected off the original document. Then it has negatively charged black particles (the toner) poured over it. The positive spots on the drum attract negatively charged toner. Now the resulting black pattern is rolled on to a sheet of paper. The paper is heated to fix the pattern and a copy is then produced. 1.2 Conductors, Insulators ...

We distinguish two basic types of substances, which differ in the way their electrons are allowed to move around. The substances in which electrons can move or less freely are called conductors, those in which electrons cannot move are called insulators. This is just a rough division, because there are many substances in which electrons have some degree of freedom of movement, so they are sort of in-between. There are also materials where only a few electrons are allowed to move freely. These are very important in electronics because semiconductors belong to this group. It is important to be able to distinguish conductors from insulators in practice. A typical conductor is a metal, such as for example aluminium, gold, copper, steel (although steel is not such a good conductor as copper) and many others (see Table 1.1). Metals all have a characteristic property that they are shiny when polished; this feature is also related to the presence of electrons. So, if you see an unknown substance and it is shiny, it is very likely to be a good conductor. A typical insulator is a compound substance, and good examples are most plastics, rubber and glass. The ability to identify good insulators is important and may be lifesaving. We will now spend some time talking about these issues. ________________________________________________ Metal Resistance (Ohms) ________________________________________________ Silver 2.02 Copper 2.16 Gold 3.11 Aluminium 3.59 Tungsten 7.13 Iron 12.7 Nichrome 191 ________________________________________________ Table 1.1 The resistance of 100-metre long wires with a diameter of 1 millimetre. First of all we concentrate on water and other liquids. Chemically pure water is an insulator, which is practically irrelevant, because most of the water in our environment - tap water, rain water, sweat etc. is NOT chemically pure and conducts electricity quite easily due to dissolved salts. We should then always assume that water is essentially a conductor3. On the other hand organic liquids such as petrol are insulators - but it needs
3 Therefore you should NEVER use a hairdryer, or other electrical appliances, in a

bathtub.
1.3

ELEC166 on Mac

to be noted that many are flammable and special safety requirements apply if these are to be used near electrical appliances or devices, like a car. Any object which is moist conducts electricity, and many everyday objects do. Wood often may contain moisture, so a fresh branch can also conduct electricity. Dry wood, however, can be considered as an insulator. Air can also be quite humid, and may conduct electricity too. This can easily be noticed, as on a humid day static electricity generated when combing hair disperses quickly. On the other hand, when humidity is low, many of us are having notorious bad-hair days, as charges cling on to hair for ages. The ground contains some moisture too and can conduct electricity quite well. Finally, all substances, even perfect insulators, will conduct electricity if they are sufficiently thin. An example is a lightning passing through air, which is essentially an insulator. In a thunderstorm a huge amount of charge is accumulated in the cloud and, despite a large distance to the ground, the charge alters the air along a path, making a conductive track - and then rushes to the ground. Similar effects may occur in a highvoltage cable. If the plastic shielding on a high-voltage cable is worn out and too thin, electric discharge from this cable will take place. This is why electricians use pliers and other tools which are specially rated. These tools are covered in thick plastic which prevents electric shock. Exercise 1.1 Which of the following everyday objects may potentially be used to rescue someone from a live electrical wire. Remember that bare hands may not be used. a damp bathroom towel, a painted metal chair, a wooden chair, a branch found in the garden. Current and Voltage Currents

1.3 1.3.1

The most popular way of producing a flow of electrons or current is to make the righthand end of a wire attract electrons and the left-hand end repel them, thus causing an overall drift of electrons to the right. For historical reasons a drift of electrons to the right is described as current flowing to the left . This is summarised in saying that the conventional direction of currents is opposite to the movement of electrons. So, the current - by tradition - is regarded as motion of positive charges, although modern science knows very well that this is not true. We could measure currents in units of electrons per second. The accepted unit is the ampere (A), where 1 ampere = 1 coulomb/sec.

1.4

ELEC166 on Mac

________________________________________________ Power station 1000 A Starter of a car 100 A Light bulb 1A Small radio 10 mA = 10 x 10-3 A Wristwatch 1 A = 1 x 10-6 A ________________________________________________ Table 1.2 Typical values of currents. You should remember that current measures the rate of flow of electrons through a conductor. However it does not indicate how hard it was to make electrons move - there is another quantity (voltage) to describe this. 1.3.2 Electric Potential - Voltage

Many issues discussed in electronics are fairly abstract. Even the concept of electricity at the very beginning of your studies may feel a bit unreal. Electricity is hard to see; we can observe some of its effects - such as lightning - but generally cannot sense it, unless a current is passing through our body. This inability to see electricity makes it difficult to develop an intuitive understanding. To facilitate this intuitive understanding we will use models. One in particular will be quite important, namely the water model of electricity. We all know how water flows in a hose and what happens if the hose is pinched at one point. We know that water generally flows downwards - to carry it upwards we need water pumps. The water model is not perfect, but illustrates a number of features of electricity. Consider two water tanks, connected by a pipe (Figure 1.2). If we place the two tanks on a table for a while, we would have the situation (at the left) where both tanks have the same water level, and there is no flow of water in the pipe. If we lifted one tank up in the air, water would flow from it into the lower reservoir. The greater is the difference in height, the greater would be the flow.

1.5

ELEC166 on Mac

Similarly, we can increase the flow of electricity in a wire by changing the conditions at its end, in a way similar to lifting one tank, which leads to difference in height and hence in water pressure. This changed condition is referred to as creating a difference in electrical potential between the ends of a wire. If there is no potential difference, then current would not flow. For a small potential difference, the current would be small. A large potential difference leads to a large current flow. Also currents flow from the higher to the lower potential. Water in our tanks behaves in exactly the same way as current in electric circuits. We emphasis here that the water analogy describes the conventional direction of currents, i.e. currents regarded as the motion of positive charges, Potential difference, often simply referred to as voltage difference, is measured in units called volts. Note that the term voltage difference refers to measurements between one end of the conductor and the other; we talk then of the voltage across the conductor. Occasionally we speak of the voltage at a point. This colloquial expression means the potential difference between that point and some standard reference point. Remember: current flows through conductors, while voltage is measured across conductors.

1.6

ELEC166 on Mac

Chapter 2
Electronic Components and Circuit Diagrams 2.1 General Comments

Electronics is concerned with various electronic components joined together in a particular way to form an electronic circuit. It provides methods to calculate currents in particular sections of such circuits, and voltages across various components of the circuit. The components are joined by conductors; in particular these are just pieces of wire of various kinds. Simple circuits may contain the following electronic elements: a) Batteries or voltage sources which make electrons move around the circuit. They have two metal buttons, or two metal stripes (terminals) which generate a certain voltage difference. One terminal is usually referred to as negative and the other as positive. When a battery is connected to the circuit, the current in this circuit is made to flow from the positive to negative terminal1. We will discuss voltage sources in more detail later on. b) Switches, which allow us to control whether the current flows or not. When the switch is open current cannot flow - as it cannot jump from one side of the switch to the other in normal circumstances. When the switch is closed it behaves as a piece of wire and current flows unimpeded. There is no general rule as to what they look like (often there are two metal strips on the two sides, and we put them in the circuit by joining circuit wires to these strips). There are also more sophisticated switches, such as 3-way and 4-way ones. c) Resistors are essentially conductors, but not extremely good ones, and the current does flow through them, but not too easily. A measure of how hard it is for current to flow through a given resistor is called its resistance. Resistance is measured in units called ohms. If the resistance is large, then the current flows with great difficulty. If it is small, then the current flows very easily and it may reach very large values. Resistors often look like tiny painted cans with two wires, one at each end. The two wires are identical and it does not matter which way they are connected in the circuit. The simplest resistors are carbon film, which is a thin layer of carbon on a ceramic rod, or metal film/metal oxide on glass rods. Wire-wound resistors are used where the resistor has to dissipate a lot of heat. Some resistors are designed to change value when heated. They are called thermistors and are used in temperature-measuring circuits. Some resistors change in value when exposed to light. They are called light-dependent resistors. Variable resistors are also available. These can be operated by means of a knob or a slider on the control panel2.

1 The current flowing from the positive to the negative terminal is this historically

accepted movement of positive charges.


2 More about resistors later in this chapter.

2.1

ELEC166 on Mac

d) Inductors and capacitors3. Simple inductors are made up of tightly wrapped multiple wire loops. For constant currents (called DC for direct currents) they behave like ordinary conductors, or - with plenty of fine wire in the loops - rather like resistors. Real differences arise when the currents through them vary in time. Capacitors are made of two conductive plates separated by a very thin insulating film. Constant current is unable to flow through them, but charge can be stored on the metal plates. Capacitors start to behave in an interesting way when the voltage applied to the plates varies with time. This actually makes current flow through a capacitor. e) Various electronic devices and integrated circuits. Electronic catalogues are full of them. For information purposes only we list here a couple of names, such as diodes, bipolar junction transistors, FETs (field-effect transistors), diode lasers, photodiodes ... the list is almost endless. What they all have in common are thin metal wires or strips attached to them, called terminals . These terminals are meant to be connected to wires or conductive paths in circuits. Sometimes we have two terminals (in diodes, laser diodes, photodiodes), sometimes we have three (in transistors), sometimes eight or more (in complicated electronic components called operational amplifiers) and in very complicated electronic chips in a computers, such as the Pentium chip, there may be many more. It is a job of an electronics technician to know what should be connected to these terminals. The recipes are sometimes quite complicated. Some devices, for example diodes, may be connected only one way round and not the other in a particular circuit. Some others, such as operational amplifiers, must have a special power supply connected to two particular terminals, and resistors must be connected between two others. We will not be dealing with what is inside of these electronic components. This approach, whereby we learn what to do with component terminals, and do not bother about its insides, treating devices as black boxes, will be our main approach in this unit. We can also connect meters in a circuit to learn what happens in the circuit when it operates. Various meters can be used, most importantly ammeters which measure currents and voltmeters to measure voltages. One can also measure resistance using ohmmeters. Sometimes these three functions are combined together in one instrument called a multimeter. The meters may be placed intentionally in various parts of the circuit in order to monitor currents, voltages or resistances. The meters are quite complicated and large instruments, compared with other electronic components. A multimeter can be say 5 cm by 10 cm by 2 cm. More about these in the following sections. The arrangement of all the components a) - e) can be shown on a layer diagram, which is like a photograph of the actual circuit. However it is easier to see how the circuit works on the circuit diagram. A circuit diagram represents components as symbols and shows connections as lines. Every circuit component is conventionally assigned a certain symbol, as shown in Figure 2.1. The way the components may be joined together is presented in Figure 2.2. Circuit diagrams are useful for designers and of use for servicing work, although an additional layout diagram is very handy - but rarely available.

3 Capacitors and inductors will also be discussed in detail later.

Their key role in

circuits will also be given.


2.2

ELEC166 on Mac

Some important ways of joining components are illustrated in Figure 2.3 a) which shows components joined in series and in Figure 2.3 b) which shows components joined in parallel. The choice of elements does not matter, it is just their arrangement which is relevant. To make matters more difficult, mixed kinds of circuits are also possible; these do not have special names. One is shown in Figure 2.4.

2.3

ELEC166 on Mac

Exercise 2.1 Draw an electronic circuit in which two resistors are joined in parallel with a capacity, and all this in series with a voltage source and a diode. Exercise 2.2 A capacitor and an inductor are connected in parallel and the two are connected in series with a constant voltage source. Will current flow through the circuit? 2.2 Electrical Quantities and Measurements

So far we have learned that there are three electrical quantities: current measured in amperes, voltages measured in volts, and resistances measured in ohms. These can be measured by instruments called ammeters, voltmeters and ohmmeters, respectively. They used to be manufactured as separate instruments, but nowadays they are often combined into one instrument called a multimeter. A multimeter is portable and usually batteryoperated4.
4 Batteries need replacement from time to time.

2.4

ELEC166 on Mac

Measurements are made using a number of selectable ranges covering both large and small values, e.g. ranges having maximum values of 10 mA and 1,000 V. There is also a switch allowing the user to select the ammeter, voltmeter or ohmmeter function. If we want to measure the current flowing through a component, we place the ammeter in series with that component as shown in Figure 2.5. Then the current flowing through the ammeter and the component should be unchanged, or very close to equal. The ammeter, like any other electronic component, has some resistance. In modern meters this resistance is small, so it may have a negligible effect on the value of the current being measured. If we want to measure the voltage difference across a component, we connect a voltmeter in parallel with the component, as shown in Figure 2.5 bottom. The voltmeter should not affect the potential difference being measured, and is therefore made to have very high resistance.

When we switch the multimeter from current to voltage, its resistance automatically changes from very small to very large. It should be noted that if, by mistake, we connect a multimeter in series into the circuit, and switch it to a voltage range, then the large resistance will cause the current to effectively stop. Ohmmeters need to be connected across the component being measured. The component must be removed from the circuitry and measured in isolation, otherwise the measured resistance would involve other components in the circuit as well. When a moving-coil multimeter is being used as an ohmmeter, it brings into action an internal battery which
2.5

ELEC166 on Mac

cause a small current flow through the components. Then this current is measured and the resistance obtained, by comparing with the current for zero ohms. Typically a moving-coil ohmmeter has zero ohms on the right-hand end of the scale, unlike the voltmeter and ammeter, which have zero on the left. Nowadays many multimeters are digital, rather than analogue. They are more accurate than traditional analogue multimeters, which have a scale and a needle. 2.3 Simple Circuits

In this section we will learn - or revise for those of you who studied this in high school how to calculate various electrical quantities in simple electronic circuit. These simple circuit will contain only: a) b) c) batteries, resistors, connecting wires.

The name circuit is appropriate, because there must be a complete return path for current which leaves the positive terminal of the battery to return to the negative one5 . The battery does not take on any overall charge. The wires have sufficiently low resistance that it can be ignored for all practical purposes. In practice, batteries may be replaced by larger instruments called power supplies, connected to a power point. The calculations are based on a few simple rules and we will go through them one by one. 2.3.1 Rule I - Ohms Law For a large variety of metallic conductors, the relationship between the current through a given conductor and the voltage across it (with certain restrictions) is very simple, and called Ohms law. Ohm used a circuit rather like that in Figure 2.6. He applied a series of voltages, measured the resulting currents and found a simple linear relationship that the current I is proportional to the voltage V. This is normally written as: V = IR where R = V/I is called the resistance of the load. This is quite a good name, as R measures to what extent the resistor resists the flow of electrons. Ohms law is only an approximate rule; there are various deviations, exceptions etc. Some materials and devices, such as for example diodes, have a completely different relationship between I and V , sometimes very nonlinear. But Ohms law applies - with constraints - to a large variety of conductors, and particularly well to commercial resistors, but also to most wires. This is why it is so useful.

5 Current is historically understood as a motion of positive charge.

This was an

unfortunate choice.
2.6

ELEC166 on Mac

It is to be remembered that 1 ohm = 1 volt / 1 ampere Students seldom get Ohms law V = I R wrong, but they often apply it wrongly, forgetting that V must be the voltage ACROSS R. 2.3.2 Rule II - Kirchhoffs First Law

This law says that the total current flowing into a junction is zero. i1 + i2 + ... + in = 0 Note that each current has an arrow to indicate its direction. If the current value is positive, then current flows in the direction of the arrow and if it is negative then it flows in the opposite direction to the arrow. Thus in Figure 2.7, for the top junction in the gray circle, we would write: -I1 + I2 + I3 = 0 where we write -I1 because the current out of the junction is I1, so the current in is -I1. The first law simply results from the observation that, if the current into a point were not zero, this point would then steadily accumulate electrons, which is not possible. Note that water in a network of connecting tubes would behavein exactly the same way. The total flow of water flowing into a junction of pipes must be equal to the total flow of water flowing out of the junction.

2.7

ELEC166 on Mac

2.3.3

Rule III - Kirchhoffs Second Law

This law says that the total voltage difference around any circuit loop (Figure 2.9) is zero. V1 + V2 + ... + Vn = 0 The second law implies that if we imagine an electron going around the loop, then, when it gets back to its point of origin, it has gained no energy. A good analogy is to imagine a circuit loop to behave like an artificial waterfall with a re-circulating system (and therefore a water pump). The water falls down the waterfall and this downward fall corresponds to a potential difference across the resistor. The potential at point B is smaller than at point A. Similarly the height at the bottom of the waterfall is smaller than at the top. Then water flows horizontally and turns back to the pump. This part corresponds to the current flowing through the wire - there is practically no potential difference across the wire. Then the water gets to the pump and is raised to the top of the waterfall. In an electrical circuit this function is fulfilled by the battery. One should be aware that the water pump needs to have power provided so we have to plug it into the mains. In the case of a battery the extra energy needed to raise electrons to higher potential is provided by chemical reactions6. Finally the water gets to the top of the waterfall and the process is repeated (Figure 2.8).

6Because of these chemicals we should dispose of batteries in a responsible way.

2.8

ELEC166 on Mac

When we look at this waterfall and its re-circulating system, we see that the water is lifted up by exactly the same distance as it falls down. So the sum of the two height DIFFERENCES is zero. Kirchhoffs second law tell that the sum of the voltage differences around the circuit loop is zero, in complete analogy. In the circuit with one resistor of value RAB and the battery with the voltage difference of E as in Fig. 2.8 the current I, the resistance R AB and the battery voltage E are related through: E - I x R AB = 0. Now we apply this rule to the circuit shown in Figure 2.7. For the left-hand loop, we would write: E 1 - R 3 I3 - R 1 I1 = 0 and E 2 - R 2 I2 - R 1 I1 = 0 for the right-hand loop. It is useful to keep in mind that currents flow very much like water. Ohms law and the behaviour of various resistors can be understood by the analogy of resistors and thin and thick tubes. Large resistors behave like very thin and long tubes, or pinched tubes which do not allow large currents of water. Small resistors behaves like very wide tubes, where large water currents can flow easily. Although the water model is useful, it is important to realise its limitations. A break in an electric circuit causes the electricity to stop flowing; it does not spill out of the end of the wire like water would from a broken pipe. An electric circuit is NOT analogous to a sprinkler system used to water lawns. Similarly to a valve which blocks a flow of water, a switch puts a gap in the conducting path to stop the flow of electricity.

2.9

ELEC166 on Mac

2.4

Potential Divider (Voltage Divider)

A potential divider is often used to get a desired voltage from an available larger one. As this requirement is common in practical circuits, potential dividers are used very often. The voltage divider circuit is presented in Figure 2.10.

The way the potential divider works is as follows. A common current I flows through R1 and R2. Clearly V I = V o + V s, VS = I x R1, VO = I x R2 VI = I x R2 + I x R1 From equations 2.2 and 2.3 VO/ VS = R2 /R1. (2.5) (2.1) (2.2) (2.3) (2.4)

That is, the input voltage is divided into two parts (V o , V s ), each proportional to the resistance across which they appear. Also, VO = I x R2 = VI x R2 /(R2 + R1) , (2.6)

which is obtained from equation 2.4. That is, the output voltage Vo is a fraction of the input voltage V I. The fraction is equal to the resistance connected across the output divided by the sum of the two resistances. You are expected to remember equation 2.6 and the meaning of its symbols.

2.10

ELEC166 on Mac

Example 2.1 Given a supply of 15 V obtain an output of 5 V. Answer: VO/ VI = 1/3 = R2 /(R1 + R2) so we require R1 to be twice as big as R2 . There are no standard resistance values7 in this ratio, so we could perhaps make R2 = 1 k and R1 = 2 k , the latter one perhaps made up of two 1k resistors in series. 2.5 Resistors in Series and in Parallel

Now we will work through the specifics of how to calculate the combined (equivalent) resistance of resistors connected in series and in parallel. The recipes are fairly simple, but useful, and often allow us to quickly simplify relatively complex circuits. The recipes can be derived from the three laws of circuits described earlier. 2.5.1 Series Connection

Two resistors connected in series are shown in Figure 2.11. The combined (equivalent) resistance is the SUM of the two. Rcombined = R1 + R2 If there are more than two resistors (say, three, four or more), then their resistances should be added.

2.5.2

Parallel Connection

Two resistors connected in parallel are shown in Figure 2.12. The combined (equivalent) resistance Rcombined is given by: 1/Rcombined = 1/R1 + 1/R2 If there are three resistors , then we add them similarly 1/Rcombined = 1/R1 + 1/R2 + 1/R3 ;
7Standard resistance values are given in the Appendices.

2.11

ELEC166 on Mac

likewise for four, five, etc.

Example 2.2 Now we show how to use the above rules to simplify a complicated arrangement of resistors as in Figure 2.13a. The object of our calculation is the value of the combined (equivalent) resistance between the points A and B. This is how to do it. You are requested to perform and verify all calculations. First we calculate the resistors that will substitute for the two parallel connections marked by the circles. The upper one turns out to be 800 , and the lower one 1200 . Then we replace the circled connections with the calculated resistors as in Figure 2.13b. Now we circle the series connection in the upper branch and in the lower branch and calculate the equivalent resistors. We come up with 2000 and 3000 . We are left with two resistors in parallel only as in Figure 2.13c. We calculate the combined (equivalent) resistance which is 1200 (Figure 2.13d).

2.12

ELEC166 on Mac

2.6

Equivalent Circuits

In the two previous sections we learned how to replace arrangements of resistors by a sequence of equivalent circuits. If a circuit is replaced by an equivalent circuit then ALL measurements performed on the external terminals of the circuit give exactly the same VALUES as those on the corresponding terminals of the original circuit. In most cases we measure the voltage and the current. So if the circuit is enclosed in a black box, we would not be able to distinguish the original circuit from its equivalent just by testing the terminals. However in the last two sections we learned only how to build equivalent circuits for circuits made of resistors only. In this section we will take one step further; we will show you the way to find equivalent circuits for circuits with resistors and voltage sources arranged in a variety of ways. Such circuits have their own name of Thevenin equivalent circuits . We will learn a simple recipe how these circuitS may be determined. A Thevenin equivalent circuit is a way to simplify any connection of DC voltage sources and resistors which are connected to two terminals A and B to become a single voltage and a single resistor (Figure 2.14). It makes no difference in which order the two components are placed in series. If either of these circuitS were placed in a box with two terminals labelled A and B, then no measurement or test using those terminals would be able to distinguish between the two circuits.

To specify the Thevenin equivalent circuit we need to give the value of the Thevenin resistor R Th and the Thevenin voltage V Th . We can find these values in one of two ways. In the first, measurement, approach we need to have access to the actual circuit and not only to its circuit diagram. First, we connect a voltmeter across the output, that is between terminal A and terminal B, to find the open-circuit voltage V oc. Then we connect an ammeter to find the short-circuit current Isc. The voltmeter provides the open-circuit conditions, because its very large resistance should not allow current to flow. The ammeter provides the short-circuit current because its very small resistance means we should not
2.13

ELEC166 on Mac

have a voltage difference across its terminals. Once we have these two measurements, we can find the Thevenin voltage V Th and the Thevenin resistance R Th . V Th is simply equal to the open-circuit voltage V oc and R Th = V oc / I sc . This method is easy to apply if we have a real circuit to measure (provided that it can withstand a short circuit).. In the second method the desired quantities, Voc and Isc, have to be calculated from the circuit diagram. Then the same relationships are used: V Th = V oc , R Th = V oc / Isc . This can be done as in the following example. Example 2.3 Derive the Thevenin equivalent for the circuit shown in Figure 2.15 left. The equivalent is actually shown in Figure 2.15 on the right.

The open-circuit voltage is just equal to the sum of the two voltages V1 and V2 and is thus: VTh = V1 + V2 . To find RTh , we have to divide VTh by Isc, the current which flows when we connect a resistanceless wire from A to B. Application of Kirchhoffs laws and Ohms law gives the equation: V1 - Isc R1 + V2 - Isc R2 = 0, Isc = (V1 + V2) / (R1 + R2) Then RTh = VTh / Isc = R1 + R2. 2.7 Real Voltage Sources

There are several ways of generating a voltage, but only two are of importance for everyday purposes. Batteries are the most familiar method, and the invention of the first battery by Alessandro Volta in 1799 made it possible to study comparatively large currents at voltage levels from 3 V to several hundred volts. A battery is, strictly speaking, a stack of cells, each cell converting chemical action into electrical voltage. In the course of this, a metal is dissolved into a metal salt, enabling a current flow. A cross-section through a
2.14

ELEC166 on Mac

battery is snown in Figure 2.16.

Some types of cells are rechargeable, so that we can pass an appropriate current through such a battery in the reverse direction and convert the metal salt back to metal. This process uses more energy than is received out of the cell. As always, no energy is created out of nowhere. Another way of generating a steady voltage was discovered by Michael Faraday in 1817. He demonstrated the first dynamo, which worked by rotating a metal disc between the poles of a magnet, using the energy of whatever was turning the disc (Faradays hand first, and later a steam engine) into an electrical voltage that could provide current (Figure 2.17). This principle is now widely used in steam- and petrol-powered generators, hydroelectricity and electricity generated by wind.

2.15

ELEC166 on Mac

If we need to generate higher voltages then our options are twofold. First, one can connect voltage sources in series. The resulting voltage is then a sum of the individual voltages of the voltage sources. Secondly, in the case of time-varying voltages, such as these provided by dynamos/generators, a component called a transformer can be used. Transformers are built of two different coils of wire wrapped around an iron core as in Figure 2.18. They step up/down the voltage in proportion to the ratio of wire loops on the two arms. All consumer electronics contains inside a small transformer which steps down the mains voltage of 230 V into lower voltages, more useful for providing power to electronic circuits. Some appliances, such as TV sets, have a step-up transformer. In colour TV the voltage is stepped up to about 2,500 V which is very high8.

Another factor that needs to be considered in the context of real voltage sources is how much current we can draw from them. We will concentrate here on the example of a simple battery. Even if we join the two terminals of a battery with an ideal conductor of zero resistance, we would not be able to draw an arbitrarily large current. All batteries are known to have internal resistance, which we should imagine as a small resistor sitting somewhere inside of a battery and not able to be separated from it. So, in a circuit we have to replace the battery with this resistance in series with a voltage source. The maximum current drawn is then Imax = Vbattery / Rinternal .

8This voltage causes the TV set to collect charged dust particles.

2.16

ELEC166 on Mac

Example 2.4 What to do if we need to draw more current from a battery than this maximum value, Imax? This may happen for example when one tries to start a car after a freezing night. The cold engine needs then more current than usual to get started. If your existing battery does not suffice, then we can take a second battery with the same voltage and connect it in parallel. We will get twice as much current as from a single battery. 2.8 Power

A useful aspect of electricity is that we can make it do a large variety of useful jobs for us. This is possible thanks to a quantity called electric power. Electric motors allow us for example to drill, lift, and drive vehicles. Power is measured in units called watts (W) and is best visualised when thinking of lifting heavy objects. About 10 watts is the amount of power needed to lift 1 kilogram by 1 metre in one second. If the lifted weight were 30 kg, still lifted by 1 m in one second, the power used would be 300 W. If the lifting occurred slowly, say 30 kg by 1 m in 10 second, then the power would only be 30 W. Light globes used in your house are likely to use 60 - 100 watts. Note that, if you were to generate that much power yourself, you would have to keep on lifting 6 - 10 kg weights by one metre in one second, which look like quite a heavy workout. The electrical power P is calculated as: P=VxI where V is the voltage across the load and I is the current through the load. If the voltage varies in time, the current would also vary and the power would vary as well. This applies to the power used in the house by light globes and other electrical appliances. In this case it is useful to talk about an average power9. 2.9 Conversion of Power to heat

If a constant voltage is applied across a resistor R we have I=V/R because of Ohms law. The power generated in the resistor is then P = V x I = V 2 /R = I2 x R . This power is dissipated in the form of heat. This effect may sometimes be useful, but more often than not for electronics it is a real nuisance. Useful applications include electric kettles, hot plates, irons, and dryers etc10. In electronics, if parts of a circuit are getting too hot, the components may malfunction. Precautions need to be then taken so that the heat is properly taken away to the environment, for example by cooling fans. Some electric
9Average power is discussed later in Chapter 3. 10Light globes get hot too, which, has to be kept in mind when changing them.

2.17

ELEC166 on Mac

components, which use high currents, have special metal plates attached and these are joined to large strange-looking metal objects called heat sinks which can be found inside many instruments. Electronic components in particular are extremely susceptible to excess heat and may stop working if their temperature is too high. This poses some problems in laptops - which have no cooling fans - and major problems in supercomputers. We cannot avoid generation of heat in electrical circuits, but in most circumstances it is undesirable and we want to minimise it. For example in an electrical motor, designed to do mechanical work, we would like as much electricity as possible to produce mechanical power, and not be wasted on heating the surroundings. This ability is numerically expressed as the efficiency. Efficiency is the ratio of useful power to the total electrical power delivered to the instrument/device. This useful power is the difference between the total delivered power and the heat, Q, generated in the device11.

= Puseful / Ptotal = (Ptotal - Q) / Ptotal


A good device, which does not waste electricity, has a high efficiency, close to one. Low efficiency means a device will generate proportionally large amounts of heat. It is interesting to compare the efficiencies of everyday objects, for example different light sources. In light sources the useful part of the electrical power is converted to light power; heat is of course unwanted. The most popular and one of the oldest light sources is the incandescent light globe, invented by Thomas Edison back in the 19th century. Not much progress has been made in this area since then, and the efficiency of the standard globes is about 3 - 5%. (The remaining electrical power is wasted on warming the ceiling.) Fluorescent lamps are quite a bit better, with efficiencies approaching 10 %. Light emitting diodes - the little indicator lights, red, yellow, and green, that you might have seen on stereos, videos, TVs and other consumer electronics - have efficiencies approaching 20%. Now researchers are working on replacing all lights with light emitting diodes, hoping to greatly improve energy savings. This example shows that energy can often be more efficiently used through technological progress. 2 . 1 0 FAQ Students often ask: Surely we cannot be expected to know all this material; what are the important things we really must know? Another (related) complaint is that there are too many equations to learn. If you regard every sentence of your notes as isolated fact which must be memorised you are certainly in real trouble. However, the number of truly independent facts and principles is quite small, enough to be manageable. Most of the content of these notes is a logical development of these few starting points. These few points need to be memorised, and the
11 Heat is measured in watts, the same unit as power, but is not as easily measured. To

measure heat you would need to enclose the device in a thermally insulating box, measure temperature increase, measure how heavy is the device and work out what it is made of and do a couple of calculations. This cumbersome task we normally leave to the manufacturer and then we look at the device efficiency provided in their specification.
2.18

ELEC166 on Mac

rest of the development can easily be reproduced. 1) It is vital to understand the distinction between voltage and current. Current flows through components but voltage appears across them. The analogy of current with water flow and voltage with height or water pressure may be helpful. 2) Ohms law needs to be remembered: V = I R, where I is the current through R and V is the voltage ACROSS R. The difference between voltage at a point (between this point and an arbitrary reference) and the voltage difference across a component must be understood. Other Laws of Circuits: a) b) the sum of currents into a junction is zero, and the sum of voltage differences is zero

should be memorised. They are easy to apply, but the sign convention may sometimes leave students confused. Hence once again the water analogy is useful. Resistors in series and resistors in parallel - expressions for combined resistance must be memorised. The potential divider circuit and its function needs to be remembered and understood. The potential divider often appears amidst other circuitry. Voltmeters and ammeters and what they do are an essential part of this unit of study. You will need to know how to connect them correctly in the circuits. An equivalent circuit cannot be distinguished from the original by measuring the current through and the voltage between the terminals. For Thevenin equivalent circuits we need to know the open-circuit voltage VTh and the short-circuit Isc; these divided give the value of the Thevenin resistance RTh. Power P = V x I.

2.19

Vous aimerez peut-être aussi