Académique Documents
Professionnel Documents
Culture Documents
Pattern Book. Each pattern is shaded to make it easier to see where to cut and where not to cut. To navigate from page to page, simply use the vertical scrollbar on the right hand side of the screen, or the Go To buttons located at the top and bottom of the screen. To print, simply click on the Printer Icon at the top of the screen, or choose Print from the File pull-down menu. Be sure to specify which page numbers you want to print, and the number of copies. You can determine the page number from the Page # box 4 of 107 at the bottom of the screen. When finished, click the First Page button to go back to the beginning to choose another section to view.
GREAT AMERICAN PATTERNS TM
Country Plate
Country Plate
Rim Design
Stock: 1/8 - 1/4 Left pattern piece
Rim Design
Center Overlay
Stock: 1/16 - 1/4
Attach hinges of your choice. Small dashed lines indicate placement of Overlay.
Drill starter hole and cut on the solid line for Back Insert. After inserting the photo/mirror, secure the Back in place with a small amount of glue or silicone.
Center Frame
Stock: 1/4
Small dashed lines indicate placement of Overlay. Secure with glue or silicone.
Drill in the corner and cut on the solid line for Back Insert. After inserting the photo/mirror, secure the Back in place with a small amount of glue or silicone.
Top
1 2
Back
3/4
Foot Instructions
1. Attach pattern with repositionable spray. 2. Cut out rear shape 3. Cut out the top shape 4. Attach Foot with glue and finishing nails or silicone
3
Back
Assembly Instructions
Assemble by first attaching the Top to the Frame with glue and finishing nails or silicone. Next attach the music box movement to the topside of the Bottom with screws or silicone. Before the silicone sets, be sure to position the Frame over the Bottom to make sure the music box movement is aligned correctly. Then secure the Bottom to the Frame. Next, attach the Arch and Feet where indicated, securing with wood glue or silicone. Now attach the metal turntable to the bottom of the wood Turntable with silicone and then attach the Figure to the Top. Finally, attach the turntable and key to the music box, and finish as desired. NOTE: It is important that the music box movement bottom is in contact with the wood (topside of the Bottom) in order to have the best tone. If using silicone, be careful to not use too much as it may squeeze out from between the 2 pieces and get into the movement itself.
Frame
Stock: 1 1/2
Arch
Stock: 1/4
Arch Support
Stock: 1/4, cut 2
Figure
Stock: 3/8 Front
Foot
Stock: 3/4, cut 3
Top / Bottom
Stock: 1/4, cut 1 each. Dashed line indicates placement of Frame
Cut slots in Top only. Adjust slot, if necessary, for thickness of material used. Drill 3/8 in Top for turntable shaft and in Bottom for key.
Roundover top edge by sanding. Small dashed lines indicate placement of Foot on Bottom.
Turntable
Stock: 1/4, countersink the bottomside with a 1 forstner bit 1/16 deep. Secure the metal turntable with super glue or silicone.
Shelf Back
Stock: 3/8"
Shelf Back
Stock: 3/8"
Shelf Top
Stock: 3/8"
Attach to Back with glue and #18 x 3/4 finishing nails or countersink for #4 x 5/8 F.H. screws.
Victorian Rocker
Assembly Instructions
To assemble, first insert Seat tab and Back tab into one side. Then attach remaining Side. Tip: to customize this rocker for your favorite seamstress, add a pin cushion to the top of the Seat and secure with glue or silicone.
Seat
Stock: 1/4
Victorian Rocker
Side
Stock: 1/4, cut 2 Left pattern piece.
Side
Stock: 1/4, cut 2 Right pattern piece.
Victorian Rocker
Back
Apply a small amount of glue to each side tab before assembly.
Stock: 1/4
Bird House
E F F F B F A H E C
Cover (E)
Stock: 1/4", cut 2
A
F F
Bird House Description Item Qty Front Back Bottom Side Cover Roof Overlay Top Floor A B C D E F G H 1 1 1 2 2 6 2 1
Side (D)
Stock: 3/8
Assembly Instructions
Assemble by first attaching the Sides, Top Floor and Bottom to the Front. Next attach the Back to this assembly. Now attach the Roof sections beginning with the bottom section on each side. Then attach the Covers, Overlays, Roof dowel and perch pegs.
Front (A)
Stock: 3/8"
Bottom
Side
Side
Bird House
3/8" dowel
Sto ver ck lay :1 /1 6 ( G "- ) 1 /8
,c
ut
Top Floor
Back (B)
Stock: 3/8" Dashed line indicates placement of Cover.
Side
Bird House
Bottom (C)
Stock: 3/8
Roof (F)
Stock: 1/4, cut 6
For bottom 2 Roof sections, place the nails closer together to accommodate overhang. Attach Roof with #18 x 5/8 finishing nails. Top
Bird House
Bracket
Stock: 1/8, cut 2
Bottom
Stock: 1/8
Divider
Stock: 1/8, cut 3
Cut 1 center Divider on this line. Cut 2 outer Dividers on this line.
Side
Stock: 1/4, cut 2 Adjust slots, if necessary, for the thickness of material used.
Side
Stock: 1/4, cut 2 Stock: 1/4 Use glue and #18 x 5/8 finishing nails to attach Shelves and Crest to Sides.
Crest
Sto helf c k: 1 /4
, c
ut
Crest
Stock: 1/4
Attach to front edge of Roof with glue and #18 x 5/8 finishing nails.
Frame
Stock: 3/4 Top pattern piece
Roof
Bore 2 3/8 holes for 2 3/4 O.D. weather instrument inserts. Stock: 1/4 Cut 2
Frame
Stock: 3/4 Bottom pattern piece 1/4" R Typ.
81 9
20
1 2 3 4
7 8 9 5 6 1
16 15
17 1
81 9
16 15
17 1
81 9
16 15
17 1
12 13 14 11
12 13 14 11
12 13 14 11
20 20
1 2 3 4
1 2 3 4
7 8 9 5 6 1 7 8 9 5 6 1
0 0
Side Insert
Stock: 1/4, cut 2
Attach to backside of 3/4 Frame stock with glue and #18 x 5/8 finishing nails.
Base
Stock: 3/4 Right pattern piece
Base
Pattern overlap line Stock: 3/4 Left pattern piece
Victorian Clock
Crest (A)
Stock: 3/8"
Note: Assemble all parts with #18 x 5/8 finishing nails and glue.
Victorian Clock
Base (B)
Stock: 3/8" Left pattern piece Stock: 3/8" Right pattern piece
Victorian Clock Description Item Qty Crest Base Front / Back Side Front Rail End Rail Roof Blank A B C D E F G H 1 1 1 ea 2 1 2 2 1
Base (B)
Assemble by first attaching the Sides to the Back, securing with glue and #18 x 5/8 finishing nails. Next, attach the Front. Now, attach the Roofs and the Crest to the front of the Roofs. Then, center the Blank from side to side on the Base and 3/8 in from the back of the Base, and secure in place with glue and finishing nails. Continue, by placing the clock assembly over the Blank and securing in place with glue and nails. Now, attach the Front Rail and End Rails to the edges of the Base, and finish as desired.
A G
C
11 10 3 9 4 8 7 6 5 12 1 2
Assembly Instructions
H F B
Victorian Clock
Victorian Clock
Note: assemble all parts with #18 x 5/8 finishing nails and glue.
Victorian Clock
Cut top at 28
Side
Side
Stock: 3/8 Cut 2 Bottom pattern piece
Pattern overlap line Attach to edge of Blank with glue and #18 x 5/8 finishing nails.
Victorian Clock
Blank (H)
Stock: 3/8
Victorian Clock
Cut Roof at 28
Back
Roof (G)
Stock: 3/8" Cut 2
Front
Frame
Stock: 1/4 - 3/8 Left pattern piece
Frame
Stock: 1/4" - 3/8" Right pattern piece
Roundover 1/4" R
Frame / Back
Stock: 1/4" - 3/8" Top pattern piece
Note: Factory made beveled mirrors are not 100% consistent in size and shape. Therefore, we recommend that you position the mirror in place on the pattern and trace around it with a red pen. Then cut on this solid line for the mirror to fit properly.
Frame / Back
Stock: 1/4 - 3/8 Bottom pattern piece
Work piece
Beveled mirror
Side view of beveled mirror details Side view of hand cut mirror detail
1/4" R typ. 3/8" 1/4" 3/8" 1/8" 1/4" BAC 1/4" R typ. Front
Silicone adhesive
Frame
Stock: 1/4" - 3/8" Left pattern piece
Frame
Stock: 1/4" - 3/8" Right pattern piece
Frame
Stock: 1/4" - 3/8" Left pattern piece
Silicone adhesive
Frame
Stock: 1/4 - 3/8 Right pattern piece
Cut on this line for hand cut mirror and rabbet backside as shown in the section drawing. Pattern overlap line
3/8"
SILICON ADHESIV E
1/8" 1/4"
Large Shelf
Back
Stock: 3/4 Left pattern piece
Drill with a 1/16 drill bit to start bevel cut. Cut clockwise with table tilting down to the right at 3 1/2 or cut counterclockwise with table tilting down to the left at 3 1/2.
Large Shelf
Back
Stock: 3/4 Right pattern piece
Large Shelf
Insert
Stock: 1/4
Insert
Stock: 1/4
Large Shelf
Insert
Stock: 1/4"
Note: Optional - cut another blank backing of contrasting material for visual effect as desired.
Large Shelf
Bracket
Stock: 3/4 Cut 2
Large Shelf
Drill and countersink to attach Shelf to Bracket and Back with #8 x 1 1/2 FH. screws.
Top
Top
Stock: 3/4 Right pattern piece.
Large Shelf
Victorian Basket
Frame
Stock: 3/4 Left pattern piece
Drill 1/8 pivot hole before sawing basket free. After routing 1/4 R countersink for #6 x 1 1/4 FH screws.
Drill a 1/16 hole to start bevel spiral cut. Saw at 3 1/2 with table tilting down to the left and using a #9 blade.
.
Pattern overlap line
1/8 drill & countersink. Attach pivot foot with #6 x 3/4 FH screw.
Victorian Basket
Frame
Stock: 3/4 Right pattern piece
Planter Basket
End
Stock: 3/4 Cut 2
Planter Basket
Top / Base
Stock: 3/4, cut 1 each Left pattern piece.
Drill and countersink bottomside of Base to attach Sides with #& x 1 1/2 FH. screws.
End
Drill a 1/16 hole to start bevel cut. Cut clockwise with table tilting down to the right at 3 or cut counterclockwise with table tilting down to the left at 3.
Top / Base
Stock: 3/4, cut 1 each Right pattern piece.
Planter Basket
Insert
Stock: 1/4 Cut 2
Planter Basket
Insert
Planter Basket
Insert
Stock: 1/4" Cut 2
Planter Basket
Side
Stock: 3/4, cut 2 Right pattern piece
End
Planter Basket
Side
Drill and countersink to attach Ends with #7 x 1 1/2 FH. screws. Stock: 3/4, cut 2 Left pattern piece
Frame
Stock: 3/4 Top pattern piece
11
12
10
Drill with a 1/16 bit and cut with table at 90 (flat). Roundover both edges 1/4 R.
Drill a 1/16 hole to start bevel cut. Saw clockwide with table tilting down to the right at 5 1/2 or cut counterclockwise with table tilting down to the left at 5 1/2.
Drill 1/8 pivot hole before sawing basket free. After routing 1/4 R countersink for #6 x 1 1/4 FH. screws.
Frame
Base
Stock: 3/4 Left pattern piece Drill and countersink bottomside for #9 x 1 1/2 FH screws.
Base
Stock: 3/4 Right pattern piece Pattern overlap line
Crest
Stock: 1/4
Side
Trinket Box
Lid Support
Stock: 1/4 Cut on this line to separate Lid and Lid Support. Attach hinges of your choice.
Lid
End Side
Trinket Box
Assembly Instructions
Assemble by first attaching the Sides and Bottom to the Front. Then attach the Back. Attach Lid Support to top of Back with glue and #18 x 5/8 finshing nails. Next, secure the Lid to the Lid Support, and attach the Crest.
Stock: 1/4
Bottom
End End
Frame
Stock: 3/4
1/4" R Typ.
3/4 "
11 10
12
1 2 3
9 4 8 7 6 5
Insert
Stock: 1/4
Insert
Stock: 1/4
Insert Base
Stock: 3/4 Drill and countersink bottomside for #7 x 1 1/2 FH screws.
Stock: 1/4
Harley Silhouette
Right Tree
Stock: 1/16 - 1/8 Spacers: 1/8, cut 3
Left Tree
Stock: 1/16 - 1/8 Spacers: 1/8, cut 3
Eagle
Stock: 1/16 - 1/8 Spacers: 1/8, cut 3
Spacers
Harley Silhouette
Drill to hang.
Frame
Stock: 1/4 Left pattern piece
Harley Silhouette
Frame
Stock: 1/4 Right pattern piece
Foot
Top view.
Front
Top
1 2
Back
Foot Instructions
1. Attach pattern with repositionable spray adhesive. 2. Cut out rear shape 3. Cut out the top shape 4. Attach Foot with glue and finishing nails or silicone
3
Back
Top Handle
Sand or cut ends 45. Stock: 1/4
3/4
Side Trim
Bottom Handle
Stock: 1/4
Lid
Fretted Box
Stock: 1/4
Side
End Side
End
Bottom
Fretted Box
Stock: 1/4
Side
End
Assembly Instructions
Assemble by first attaching the Sides to the Ends. Then secure this assembly to the Bottom. Attach the Lid support to the bottomside of the Lid, and then attach the Handle Support and Handle. Now attach the Feet with glue and finishing nails. Then attach the Front, Back and Side Trim. Finally, secure the music movement in place. Adjust slot, if necessary for the thickness of material Side
Side
Stock: 1/4, cut 2
End
Stock: 1/4, cut 2
Lid Support
Moose Silhouette
Overlay
Frame
Moose Silhouette
Frame
Dashed lines indicate placement of Overlays.
Frame
Frame
Stock: 3/4" Bottom pattern piece 1/4" R Typ.
3/4"
Dashed line indicates placement of Insert on backside. Glue in place. Rabbet backside for fretted insert
Stock: 1/4
Insert
Stock: 1/4
Insert
Stock: 1/4
Insert
Base
Stock: 3/4 Right pattern piece
Base
Roundover top edges 1/4 R Stock: 3/4 Left pattern piece
Mini Clock
11 10
12
1 2 3
9 4 8 7 6 5
Frame
Stock: 1/4" - 3/8"
Base
Stock: 1/4" - 3/4" Use glue to attach Frame to Base.
Mini clock
11 10
12
1 2 3
9 4 8 7 6 5
Frame
Stock: 1/4 - 3/8
Base
Stock: 1/4 - 3/4 Use glue to attach Frame to Base
Mini clock
11 10
12
1 2 3
9 4 8 7 6 5
Frame
Stock: 1/4 - 3/8
Base
Stock: 1/4 - 3/4 Use glue to attach Frame to Base
Shelf
Stock: 1/4
Si
Ad thic just sl kne ot, i ss o f ne f m cess ater ary ial , for use d.