Académique Documents
Professionnel Documents
Culture Documents
___________________________Features
o Input Range: Up to 40V o 5A On-Chip Power Switch o Fixed Outputs: 5V (MAX787) 3.3V (MAX788) 3V (MAX789) o 100kHz Switching Frequency o Excellent Dynamic Characteristics o Few External Components o 8.5mA Quiescent Current o TO-220 Package
MAX787/MAX788/MAX789
______________Ordering Information
PART MAX787CCK MAX787ECK MAX788CCK MAX788ECK MAX789CCK MAX789ECK TEMP. RANGE 0C to +70C -40C to +85C 0C to +70C -40C to +85C 0C to +70C -40C to +85C PIN-PACKAGE 5 TO-220 5 TO-220 5 TO-220 5 TO-220 5 TO-220 5 TO-220
_______________________Applications
Distributed Power from High-Voltage Buses High-Current, High-Voltage Step-Down Multiple-Output Buck Converter
50H
OUTPUT 5V AT 5A
MAX789
__________________Pin Configuration
FRONT VIEW
MAX787
VC 2.7k GND 0.01F SENSE
MBR745 470F
5 4 3 2 1
Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = 25V, Tj = TMIN to TMAX, unless otherwise noted.) PARAMETER Input Supply Voltage Range ISW = 1A Switch-On Voltage (Note 1) ISW = 5A Switch-Off Leakage Supply Current (Note 3) Minimum Supply Voltage Switch-Current Limit (Note 5) Maximum Duty Cycle Tj = +25C Switching Frequency VOUT = VSENSE = 0V (Note 5) Switching Frequency Line Regulation Error-Amplifier Voltage Gain Error-Amplifier Transconductance Error-Amplifier Source Current Error-Amplifier Sink Current VSENSE = VOUT - 10% VSENSE = VOUT + 10% 8V VIN 40V 1V VC 4V Tj = +25C Tj = +25C Tj = +25C Tj = +25C 3000 100 0.6 Tj +125C Tj = +25C VIN = 25V, VSW = 0V VIN = 40V, VSW = 0V VIN 40V, VSENSE = 5.5V Normal Mode Start-Up Mode (Note 4) Tj 0C Tj < 0C 5.5 85 90 85 20 0.03 2000 5000 140 1.0 9000 225 1.7 0.10 %/V V/V mho A mA Tj 0C Tj < 0C Tj 0C Tj < 0C Tj = +25C Tj = +25C 5 10 8.5 7.3 3.5 3.5 6.5 90 100 CONDITIONS MIN 8.0 TYP MAX 40.0 1.85 2.10 2.30 2.50 300 500 11 8.0 4.8 5.0 8.5 110 120 kHz A % V A mA V UNITS V
_______________________________________________________________________________________
MAX787/MAX788/MAX789
Tj = +25C
VOUT (nominal) = 5V (MAX787), 3.3V (MAX788), or 3V (MAX789); Tj = +25C all conditions of input voltage, Tj = TMIN to output voltage, and load TMAX current 8V VIN 40V 0% duty cycle 0% duty cycle Tj = +25C Tj = TMIN to TMAX
Output Voltage Line Regulation VC Voltage VC Voltage Temperature Coefficient Thermal Resistance Junction to Case (Note 6)
2.5
Note 1: Do not exceed switch-to-input voltage limitation. Note 2: For switch currents between 1A and 5A, maximum switch-on voltage can be calculated via linear interpolation. Note 3: By setting the SENSE pin to 5.5V, the VC pin is forced to its low clamp level and the switch duty cycle is forced to zero, approximating the zero load condition. Note 4: For proper regulation, total voltage from VIN to GND must be 8V after start-up. Note 5: To avoid extremely short switch-on times, the switch frequency is internally scaled down when VSENSE is less than 2.6V (MAX787), 2.0V (MAX788), or 1.8V (MAX789). Switch-current limit is tested with VSENSE adjusted to give a 1s minimum switch-on time. Note 6: Guaranteed, not production tested.
______________________________________________________________Pin Description
PIN 1 NAME SENSE FUNCTION SENSE Input is the internal error amplifier's input, and should be directly connected to VOUT. SENSE also aids current limiting by reducing oscillator frequency when VOUT is low. Error-Amplifier Output. A series RC network connected to this pin compensates the MAX787/MAX788/ MAX789. Output swing is limited to about 5.8V in the positive direction and -0.7V in the negative direction. VC can also synchronize the MAX787/MAX788/MAX789 to an external TTL clock in the 115kHz to 170kHz range. See MAX724/MAX726 data sheet. Ground requires a short, low-noise connection to ensure good load regulation. The internal reference is referred to GND, so errors at this pin are multiplied by the error amplifier. Internal Power Switch Output. The Switch output can swing 35V below ground and is rated for 5A. VIN supplies power to the internal circuitry and also connects to the collector of the internal power switch. VIN must be bypassed with a low-ESR capacitor, typically 200F or 220F.
VC
3 4 5
_______________________________________________________________________________________
D L2
J1
L L1 C1 B e J2 J3
INCHES MAX MIN 0.190 0.140 0.040 0.015 0.022 0.014 0.650 0.560 0.420 0.380 0.067 BSC 0.055 0.045 0.270 0.230 0.115 0.080 0.580 0.500 0.161 0.139 0.120 0.100
A E Q H1 P F
DIM A B C1 D E e F H1 J1 L P Q
J1
C1
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
4 ___________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600 1995 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.