Académique Documents
Professionnel Documents
Culture Documents
A. K. H. KWAN* AND F. T. K. AU
Department of Civil Engineering, University of Hong Kong, Hong Kong
SUMMARY
Flanged sections are often used for long-span concrete beams to maximize their structural efficiency. However,
although for the same sectional area a flanged section could render a higher flexural strength, it would also lead
to a lower flexural ductility, especially when heavily reinforced. Thus, when evaluating the flexural performance
of a beam section, both the flexural strength and ductility need to be considered. In this study, the post-peak flex-
ural behaviour of flanged sections is evaluated by means of an analytical method that uses the actual stress–strain
curves of the materials and takes into account strain reversal of the tension reinforcement. From the numerical
results, the flexural strength–ductility performance of flanged sections is investigated by plotting the strength and
ductility that could be simultaneously achieved in the form of design graphs. It is found that (1) at the same
overall dimensions and with the same amount of reinforcement provided, a flanged section has lower flexural
ductility than a rectangular section; (2) at the same overall dimensions, a flanged section has inferior strength–
ductility performance compared to a rectangular section; and (3) at the same sectional area, a flanged section has
better strength–ductility performance compared to a rectangular section. Copyright © 2004 John Wiley & Sons,
Ltd.
1. INTRODUCTION
When a reinforced concrete beam section is subjected to flexure, the applied bending moment is resis-
ted jointly by the compressive force developed in the concrete and the tensile force developed in the
steel reinforcement, which are equal and opposite to each other and together form a couple, as illus-
trated in Figure 1(a). Let the compressive force in the concrete and the tensile force in the reinforce-
ment be denoted by C and T respectively and the lever arm, i.e. the distance between C and T, be
denoted by a. Since the applied bending moment is always equal to C or T times a, for given C and
T, the flexural strength of the beam section increases with the lever arm a. Hence, a larger lever arm
would lead to a better structural efficiency of the beam section. One way to increase the lever arm is
to increase the depth of the beam section, but very often the depth of a beam section is limited because
of the headroom or other geometric requirements and cannot be increased without affecting the overall
layout of the structure. If the depth of the beam section cannot be increased, an alternative is to change
the beam section to a flanged section, as shown in Figure 1(b). In a flanged section, such as a T- or
box-shaped section, most of the concrete is located near the extreme compression fibre and thus the
line of action of C is at a larger distance from that of T. Because of the larger lever arm in a flanged
section than in a rectangular section, the structural efficiency of a flanged section is generally larger
than that of a rectangular section.
* Correspondence to: Professor A. K. H. Kwan, Department of Civil Engineering, The University of Hong Kong, Pokfulam
Road, Hong Kong. E-mail: khkwan@hku.hk
Copyright © 2004 John Wiley & Sons, Ltd. Received December 2002
Accepted February 2003
30 A. K. H. KWAN AND F. T. K. AU
la
la
It is sometimes argued that the concrete near the geometric centre of the section is of little use
because it develops small compressive stresses and contributes little to the flexural strength, and that
the higher structural efficiency of a flanged section is attained mainly by relocating the concrete near
the centre of the section to the flange area near the extreme compression fibre where much higher
compressive stresses would be developed (Ferguson, 1981). In actual fact, apart from contributing to
the shear and torsional strengths of the beam section, the concrete near the centre also contributes sig-
nificantly to the flexural ductility of the beam section. At the post-peak stage, when the peak bending
moment has already been reached and the moment resisting capacity of the beam section is decreas-
ing, the concrete near the extreme compression fibre would gradually lose its strength and the neutral
axis of the section would move towards the tension reinforcement. Consequently, the concrete near
the centre would at the post-peak stage develop much higher compressive stresses than before and
contribute significantly to the residual moment resisting capacity of the section. Because of this, a rec-
tangular section, which has relatively more concrete near the centre, is generally more ductile than a
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 31
flanged section. In other words, although a flanged section has a higher structural efficiency in terms
of flexural strength, it might at the same time have a somewhat lower flexural ductility.
Since ductility may also be a governing factor determining the safety of a structure, when evaluat-
ing the structural performance of a beam both the flexural strength and ductility need to be consid-
ered. Maximizing the flexural strength or the structural efficiency in terms of flexural strength without
paying proper attention to the flexural ductility may not produce the best overall structural perform-
ance. The best way to evaluate the flexural strength–ductility performance of a beam section is to eval-
uate the flexural strength and flexural ductility that could be simultaneously achieved at various levels
of reinforcement, as will be illustrated in this paper. However, while the flexural strength of a beam
section can be determined quite easily using the ordinary beam bending theory, it is not possible to
evaluate the flexural ductility using any simple analytical method. To evaluate the flexural ductility
of a beam section, it is necessary to carry out non-linear flexural analysis, extended well into the
post-peak range so that the ability of the beam section in withstanding inelastic curvature without
excessive loss in flexural strength may be determined. Such kind of analysis is highly non-linear and
involves stress path dependence of the constitutive materials during strain reversal at the post-peak
stage.
In most books on reinforced concrete design, the analysis of flanged beams is just treated as a
straightforward extension of that for rectangular beams. That is probably the reason why, compared
with investigations on the structural behaviour of rectangular beams, much less work has been done
on flanged beams. Moreover, the previous work on flanged beams generally concentrated on aspects
other than the post-peak flexural behaviour. For example, Swamy et al. (1973) studied the shear resist-
ance of T-beams with varying flange widths and found that the shear resistance of T-beams was
significantly increased by the flange width, the percentage of tension steel and the amount of web
reinforcement. Desayi et al. (1978) conducted tests of reinforced concrete T-beams and rectangular
beams to study the influence of the flange on the torsional strength of reinforced concrete T-beams.
The results indicated that the torsional strength contribution of the flange may be estimated by the
plastic theory of torsion. Prakash Rao (1982) presented a comprehensive summary of the research
done in Europe on the design of webs and web–flange junctions under combined bending and shear,
taking into account the interaction between various forces acting on the section. Subedi et al. (1992)
and Subedi (1993) carried out experimental work focusing on the failure behaviour of thin-walled
reinforced concrete flanged beams and observed that the major modes of failure were flexure, diago-
nal splitting and web crushing. So far, there has been little research on the post-peak flexural behav-
iour of flanged beams.
At the University of Hong Kong, a new method of non-linear flexural analysis that uses the actual
stress–strain curves of the materials and takes into account stress path dependence of the tension
reinforcement has recently been developed and applied to study the post-peak flexural behaviour of
singly and doubly reinforced rectangular beam sections (Ho et al., 2003; Pam et al., 2001). It has been
found from these studies that at the post-peak stage both the line of action of C and the neutral axis
of the section would gradually shift towards the tension reinforcement and then at a certain point the
axial strain of the tension reinforcement would start to decrease, causing strain reversal in the tension
reinforcement and consequently stress path dependence of the tensile stress developed therein. Using
this newly developed method, the effects of various structural parameters including the concrete grade,
the tension and compression steel yield strengths and the tension and compression steel area ratios on
the flexural ductility of rectangular beam sections have been quite thoroughly studied (Kwan et al.,
2003).
In the present study, the aforementioned method of analysis has been extended to deal with flanged
sections. Using the extended analysis method, the non-linear flexural behaviours of typical flanged
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
32 A. K. H. KWAN AND F. T. K. AU
sections have been analysed and compared to those of rectangular sections with the same overall
dimensions. After gaining a better understanding of the non-linear flexural behaviour of flanged sec-
tions, the flexural strength and ductility that could be simultaneously achieved by flanged sections of
different shapes have been evaluated. From the numerical results obtained, the flexural strength–duc-
tility performance of flanged sections has been studied by plotting the flexural ductility against the
flexural strength in the form of graphs that may in fact be used as design charts. The results revealed
that in the design of flanged beam sections more attention to the provision of sufficient flexural duc-
tility is generally needed.
2. METHOD OF ANALYSIS
The constitutive model for unconfined concrete developed by Attard and Setunge (1996), which has
been shown to be applicable to a broad range of concrete strength from 20 to 130 MPa, is adopted in
the moment–curvature analysis. The stress–strain curve of the constitutive model is given by
2
K1 (e c e co ) + K2 (e c e co )
s c fco = 2
(1)
1 + ( K1 - 2)(e c e co ) + ( K2 + 1)(e c e co )
in which sc and ec are the compressive stress and strain at any point on the stress–strain curve, fco and
eco are the compressive stress and strain at the peak of the stress–strain curve, and K1 and K2 are coef-
ficients dependent on the concrete grade. It should be noted that fco is actually the in situ compressive
strength, which may be estimated from the cylinder or cube compressive strength using appropriate
conversion factors. Figure 2(a) shows some typical stress–strain curves so derived.
For the steel reinforcement, a linearly elastic–perfectly plastic stress–strain curve is adopted. Since
there could be strain reversal in the steel reinforcement at the post-peak stage despite monotonic
increase of curvature (Ho et al., 2003; Pam et al., 2001), the stress–strain curve of the steel is stress-
path dependent. It is assumed that when strain reversal occurs, the unloading path of the stress–strain
curve is linear and has the same slope as the initial elastic portion of the stress–strain curve. Figure
2(b) shows the resulting stress–strain curve of the steel reinforcement.
Only three other basic assumptions have been made in the analysis: (1) plane sections before
bending remain plane after bending, (2) the tensile strength of concrete is negligible, and (3) there is
no bond-slip between concrete and steel. These assumptions are widely accepted in the literature (Park
and Paulay, 1975). The moment–curvature behaviour of the beam section is analysed by applying pre-
scribed curvatures to the beam section incrementally starting from zero. At a prescribed curvature, the
strain profile in the section is first evaluated based on the above assumptions. From the strain profile
so obtained, the stresses developed in the concrete and the steel reinforcement are determined from
their respective stress–strain curves. The stresses developed have to satisfy the axial equilibrium con-
dition, from which the neutral axis depth is evaluated by iteration. Having determined the neutral axis
depth, the resisting moment is calculated from the moment equilibrium condition. The above proce-
dure is repeated until the curvature is large enough for the resisting moment to increase to the peak
and then decrease to 50% of the peak moment. Details of the analysis procedure have been presented
in Ho et al. (2003) and Pam et al. (2001).
The method of analysis previously applied to solid rectangular sections is extended to deal with
flanged sections by taking the width of the section as a variable instead of a constant. For instance, in
the following equations governing the axial and moment equilibrium conditions of the flanged beam
section shown in Figure 3:
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 33
80
70 fco
fco=30MPa
60 ffco=50MPa
co
Stress (MPa)
50 fco=70MPa
fco
40
30
20
10
0
0 0.001 0.002 0.003 0.004 0.005 0.006
Strain
(a) Concrete
fy ss = fy
Stress
unloading
ss =Es(es-ep)
Es ep Es
Strain
dn
P = Ú s c bdx + Â Ascs sc - Â Asts st (2)
0
dn
M = Ú s c bxdx + Â Ascs sc (dn - D1 ) + Â Asts st ( D - dn ) (3)
0
where P is the applied axial load (compressive force taken as positive), M is the resisting moment
(sagging moment taken as positive) and b is the width of the section at x from the neutral axis, the
width b is taken as a variable during the numerical integration. Because of the variable width of the
flanged section, a more sophisticated numerical integration technique has to be used when integrating
over the concrete section to determine the axial force and the resisting moment contributed by the
stresses developed in the concrete. In the present study, Romberg integration (Gerald and Wheatley,
1999), which can significantly improve the accuracy of the simple trapezoidal rule when the integrand
is known at equispaced intervals, has been adopted.
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
34 A. K. H. KWAN AND F. T. K. AU
B
Asc
D1
Df ssc
b dn
x
Neutral
axis D
Ast
sst
Bw
Stress
Section distribution
Bw =400mm Bw =800mm
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 35
are named Section A, Section B and Section C. Section A is a T-shaped section with web breadth and
flange depth given by Bw = 400 mm and Df = 400 mm respectively, while Section B is a T-shaped
section with web breadth and flange depth given by Bw = 800 mm and Df = 400 mm respectively. On
the other hand, Section C is a solid rectangular section. In each section, the same amount of tension
reinforcement given by Ast = 40,000 mm2 is provided. However, no compression reinforcement is pro-
vided in any of the three sections. For a preliminary study, the in situ concrete compressive strength
fco is fixed at 50 MPa, while the yield strength fyt and Young’s modulus Es of the steel reinforcement
are fixed at 460 MPa and 200 GPa respectively.
30
25
Bending moment (MNm)
20
Section C
15
Section B
10 Section A
0
0 2 4 6 8 10 12 14 16 18 20
Curvature ( X10-3 radian/m)
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
36 A. K. H. KWAN AND F. T. K. AU
m = fu f y (4)
where fu and fy are the ultimate curvature and yield curvature respectively. The ultimate curvature fu
is taken as the curvature of the beam section when the resisting moment of the beam section has, after
reaching the peak value of Mp, dropped to 0·8 Mp. On the other hand, the yield curvature fy is taken
as the curvature at the hypothetical yield point of an equivalent linearly elastic–perfectly plastic system
with an elastic stiffness equal to the secant stiffness of the section at 0·75 Mp and a yield moment
equal to Mp.
25
fco=30MPa.
fco Section A
20 fco=30MPa,
fco Section B
Curvature ductility factor m
fco=30MPa,
fco Section C
15 fco=70MPa,
fco Section A
fco
fco=70MPa, Section B
fco=70MPa,
fco Section C
10
0
0 20,000 40,000 60,000 80,000 100,000 120,000
Tension steel area, Ast (mm2)
Figure 6. Variation of curvature ductility factor m with tension steel area Ast
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 37
the same amount of reinforcement, a change in sectional shape from rectangular to flanged shape could
lead to a change of failure mode from ductile tension failure to brittle compression failure. This is
because in general a flanged section has a smaller balanced steel area (the tension steel area at which
balanced failure occurs) than a rectangular section.
It is also evident from Figure 6 that at the same tension steel area the flexural ductility increases
slightly with the concrete grade, albeit a higher-grade concrete should be less ductile. This may also
be explained by looking at the degree of the beam section being under- or over-reinforced. The balance
steel area is larger when the concrete grade is higher. Thus, relatively, at the same tension steel area,
the tension to balanced steel ratio (the ratio of the tension steel area to the balanced steel area) is
smaller when a higher-grade concrete is used. The tension to balanced steel ratio may be interpreted
as a measure of the degree of the beam section being under/over-reinforced. When the tension to bal-
anced steel ratio is smaller, the degree of the beam section being under-reinforced is higher and the
degree of the beam section being over-reinforced is lower. Therefore, at the same tension steel area,
the degree of the beam section being under-reinforced increases with the concrete grade and as a result
the flexural ductility increases slightly with the concrete grade.
From the above, it is obvious that one major structural parameter determining the flexural ductility
is the tension to balanced steel ratio, which is denoted hereafter by l. Figure 7 shows the variation of
the curvature ductility factor m with the tension to balanced steel ratio l for the beam sections analysed
at different concrete grades. It is seen that regardless of the concrete grade and the shape of the beam
section, m decreases as l increases and then remains roughly constant when l > 1·0. In general, at the
same concrete grade and the same tension to balanced steel ratio, the m-value of a flanged section is
slightly higher than that of a rectangular section with the same overall dimensions when l < 0·85
(when the sections are lightly reinforced) and the m-value of a flanged section is slightly lower than
that of a rectangular section with the same overall dimensions when l > 0·85 (when the sections are
heavily reinforced). Nevertheless, since a flanged section has a smaller balanced steel area compared
to that of a rectangular section, at the same tension steel area, a flanged section has a higher tension
to balanced steel ratio and therefore a lower flexural ductility, especially when the section is heavily
reinforced. Figure 7 also reveals that at the same tension to balanced steel ratio, regardless of the sec-
25
ffco=30MPa.
co Section A
20 ffco=30MPa, Section B
Curvature ductility factor m
co
ffco=30MPa,
co Section C
15 ffco=70MPa,
co Section A
ffco=70MPa,
co Section B
ffco=70MPa,
co Section C
10
0
0.0 0.2 0.4 0.6 0.8 1.0 1.2
Tension to balanced steel ratio l
Figure 7. Variation of curvature ductility factor m with tension to balanced steel ratio l
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
38 A. K. H. KWAN AND F. T. K. AU
tional shape, the flexural ductility decreases as the concrete grade increases, for the simple reason that
a higher-grade concrete is generally less ductile.
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 39
Df/D=0.1,
Df /D Bw/B=0.1
Bw /B Df/D=0.3, Bw/B=0.1
D f /D B w /B
20 Df/D=0.1,
D f /D
Bw/B=0.2
Bw /B 20 Df/D=0.3,
D Bw/B=0.2
Bw /B
f /D
Df/D=0.1,
D f /D
Bw/B=0.3
Bw /B Df/D=0.3,
D Bw/B=0.3
Bw /B
f /D
Df/D=0.1,
D f /D
Bw/B=0.4
Bw /B Df/D=0.3,
D Bw/B=0.4
Bw /B
f /D
15 Df/D=0.2, Bw/B=0.1
Bw /B 15
Df /D Df/D=0.4,
Df /D Bw/B=0.1
Bw /B
Df/D=0.2, Bw/B=0.2
B w /B Df/D=0.4, Bw/B=0.2
Bw /B
m
m
Df /D Df /D
Df/D=0.2,
Df /D B w /B
Bw/B=0.3 Df/D=0.4,
D f /D Bw/B=0.3
Bw /B
10 10
Df/D=0.2,
D f /D
Bw/B=0.4
Bw /B Df/D=0.4,
D f /D Bw/B=0.4
Bw /B
Rectangular Rectangular
5 5
0 0
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
Mp /BD 2 (MPa) Mp /BD 2 (MPa)
Df/D=0.1,
D f /D Bw/B=0.1
Bw /B Df/D=0.3,
D f /D
Bw/B=0.1
B w /B
20 Df/D=0.1,
D f /D Bw/B=0.2
Bw /B 20 Df/D=0.3,
D f /D
Bw/B=0.2
Bw /B
Df/D=0.1,
D f /D Bw/B=0.3
Bw /B Df/D=0.3,
D f /D Bw/B=0.3
Bw /B
Df/D=0.1,
Df /D Bw/B=0.4
Bw /B Df/D=0.3,
D f /D Bw/B=0.4
B w /B
15 Df/D=0.2, Bw/B=0.1 15 Df/D=0.4, Bw/B=0.1
Df /D Bw /B Df /D Bw /B
Df/D=0.2,
D f /D
Bw/B=0.2
Bw /B m Df/D=0.4,
D /D Bw/B=0.2
B w /B
m
f
Df/D=0.2,
D f /D
Bw/B=0.3
Bw /B Df/D=0.4,
D f /D Bw/B=0.3
Bw /B
10 10
Df/D=0.2,
D Bw/B=0.4
Bw /B Df/D=0.4,
D f /D Bw/B=0.4
Bw /B
f /D
Rectangular Rectangular
5 5
0 0
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
2
Mp /BD (MPa) M p /BD 2 (MPa)
Df/D=0.1,
D f /D
Bw/B=0.1
Bw /B Df/D=0.3, Bw/B=0.1
D f /D Bw /B
20 Df/D=0.1,
D f /D Bw/B=0.2
Bw /B 20 Df/D=0.3, Bw/B=0.2
D f /D Bw /B
Df/D=0.1,
D /D Bw/B=0.3
B w /B Df/D=0.3,
D Bw/B=0.3
f f /D B w /B
Df/D=0.1,
D f /D Bw/B=0.4
Bw /B Df/D=0.3,
D f /D Bw/B=0.4
B w /B
15 Df/D=0.2,
D Bw/B=0.1
Bw /B 15 Df/D=0.4, Bw/B=0.1
f /D Df /D Bw /B
Df/D=0.2,
Df /D Bw/B=0.2
Bw /B Df/D=0.4,
D f /D
Bw/B=0.2
Bw /B
m
Df/D=0.2,
Df /D B
Bw/B=0.3
w /B Df/D=0.4,
D f /D
Bw/B=0.3
Bw /B
10 10 Df/D=0.4, Bw/B=0.4
Df/D=0.2,
D f /D Bw /B
Bw/B=0.4 Df /D Bw /B
Rectangular Rectangular
5 5
0 0
0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0 0.0 2.0 4.0 6.0 8.0 10.0 12.0 14.0 16.0 18.0 20.0
2 2
M p /BD (MPa) M p /BD (MPa)
generally have much better flexural strength–ductility performances. The advantage of using high-
strength concrete is thus obvious. Although a high-strength concrete is more brittle than a normal-
strength concrete, its higher compressive strength, which leads to a larger balanced steel area, does
allow a higher flexural strength–ductility performance of the beam section to be achieved. In other
words, the use of high-strength concrete could allow a higher flexural strength to be achieved at the
same flexural ductility, or a higher flexural ductility to be achieved at the same flexural strength, or
both a slightly higher flexural strength and a slightly higher flexural ductility to be achieved at the
same time.
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
40 A. K. H. KWAN AND F. T. K. AU
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 41
Df/D=0.1,
D f /D
Bw/B
Bw /B=0.1 Df/D=0.3,
D f /D
Bw/B
B w /B=0.1
20 Df/D=0.1,
Df /D Bw/B
Bw /B=0.2 20 Df/D=0.3,
D f /D
Bw/B
Bw /B=0.2
Df/D=0.1,
Df /D Bw/B
Bw /B=0.3 Df/D=0.3,
D f /D Bw/B
B w /B=0.3
Df/D=0.1,
D f /D
Bw/B
Bw /B=0.4 Df/D=0.3,
D f /D
Bw/B
Bw /B=0.4
15 Df/D=0.2,
D Bw/B
Bw /B=0.1 15 Df/D=0.4, Bw/B
f /D Df /D Bw /B=0.1
Df/D=0.2,
Df /D Bw /B=0.2
Bw/B Df/D=0.4, Bw/B
Bw /B=0.2
m
m
Df /D
Df/D=0.2,
Df /D Bw /B=0.3
Bw/B Df/D=0.4,
Df /D Bw/B
Bw /B=0.3
10 10
Df/D=0.2,
Df /D Bw/B
Bw /B=0.4 Df/D=0.4,
D f /D Bw/B
Bw /B=0.4
Rectangular Rectangular
5 5
0 0
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0
Mp /A c D (MPa) Mp /A c D (MPa)
Df/D=0.1,
Df /D Bw/B=0.1
Bw /B Df/D=0.3,
D f /D
Bw/B=0.1
B w /B
Df/D=0.1,
Df /D Bw/B=0.2
Bw /B Df/D=0.3,
D f /D Bw/B=0.2
Bw /B
20 20
Df/D=0.1,
Df /D Bw/B=0.3
Bw /B Df/D=0.3, Bw/B=0.3
B
D f /D w /B
Df/D=0.1,
Df /D Bw/B=0.4
Bw /B Df/D=0.3, Bw/B=0.4
D f /D B w /B
Df/D=0.2,
Df /D Bw/B=0.1
B w /B Df/D=0.4, Bw/B=0.1
15 15 D f /D Bw /B
Df/D=0.2,
Df /D Bw/B=0.2
Bw /B Df/D=0.4,
D f /D Bw/B=0.2
Bw /B
m
Df/D=0.2,
Df /D Bw/B=0.3
m
Bw /B Df/D=0.4, Bw/B=0.3
Df/D=0.2, Bw/B=0.4 Df /D Bw /B
D f /D Bw /B
10 10 Df/D=0.4,
D f /D
Bw/B=0.4
Bw /B
Rectangular
Rectangular
5 5
0 0
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0
M p /A c D (MPa) Mp /A c D (MPa)
Df/D=0.2,
D Bw/B=0.4
Bw /B Df/D=0.4,
D f /D
Bw/B=0.3
Bw /B
f /D
10 10 Df/D=0.4, Bw/B=0.4
Rectangular D f /D Bw /B
Rectangular
5 5
0 0
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0
Mp /Ac D (MPa) Mp /A c D (MPa)
If, however, not just the overall dimensions, but also the sectional shape of the beam section (i.e.
Bw /B and Df /D) have already been fixed, then Figure 9 may also be used for the design. The proce-
dures are the same as before except that instead of plotting the point (Mp /BD2, m) on the charts, the
point (Mp /AcD, m) is to be plotted on the various charts in Figure 9.
6. CONCLUSIONS
The post-peak flexural behaviour of flanged beam sections cast of normal- and high-strength concrete
has been studied by an analytical method that uses the actual stress–strain curves of the materials and
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
42 A. K. H. KWAN AND F. T. K. AU
takes into account strain reversal of the tension reinforcement. It was revealed that although the con-
crete in the web contributes little to the peak resisting moment, it does contribute to the residual resist-
ing moment at the post-peak stage and thus the flexural ductility of the section. In other words, at the
same overall dimensions and with the same materials used, a flanged section would generally have a
lower flexural ductility compared to that of a rectangular section. It was also found that regardless of
the sectional shape, at the same tension steel area, the flexural ductility increases slightly with the
concrete grade but at the same tension to balanced steel ratio the flexural ductility decreases as the
concrete grade increases.
A parametric study has been carried out to evaluate the effects of various structural parameters on
the flexural strength–ductility performance of flanged sections. Based on the numerical results, the flex-
ural strength–ductility performance of different beam sections was compared by plotting the flexural
strength and flexural ductility that could be simultaneously achieved in the form of graphs. The graphs
showed that at the same overall dimensions the flexural strength–ductility performance of a flanged
section is inferior to that of a rectangular section. Hence, although at the same overall
dimensions a flanged section has a smaller sectional area than a rectangular section, its flexural
strength–ductility performance is not as good. However, at the same sectional area, the flexural
strength–ductility performance of a flanged section is better than that of a rectangular section. Hence,
even with the lower flexural ductility discounted, the change from a rectangular to a flanged section
would at the same sectional area improve the flexural strength–ductility performance. Lastly, by com-
paring the performance curves for beam sections cast of different grades of concrete, it was shown that
for the same sectional shape and dimensions a beam section cast of a higher-strength concrete would
have better flexural strength–ductility performance. Hence, although a high-strength concrete is gen-
erally more brittle, its use could at the same flexural strength lead to an increase in flexural ductility.
The flexural strength–ductility performance curves developed may also be used as design charts for
the preliminary design of beam sections even before the shape of the section and the concrete grade
are decided. A numerical example illustrating the use of these charts has been presented.
ACKNOWLEDGEMENTS
The work described in this paper was carried out with financial support provided by the Croucher
Foundation of Hong Kong.
REFERENCES
Attard MM, Setunge S. 1996. The stress strain relationship of confined and unconfined concrete. ACI Materials
Journal 93(5): 432–444.
Desayi P, Sundara Raja Iyengar KT, Venkatakrishnaiah M. 1978. Influence of flange on the torsional strength of
reinforced concrete T-beams. Journal of the Institution of Engineers (India), Part CV: Civil Engineering Divi-
sion 58(CI 5): 243–246.
Ferguson PM. 1981. Reinforced Concrete Fundamentals (4th edn). Wiley: New York.
Gerald CF, Wheatley PO. 1999. Applied Numerical Analysis (6th edn). Addison-Wesley: Reading, MA.
Ho JCM, Kwan AKH, Pam HJ. 2003. Theoretical analysis of post-peak flexural behavior of normal- and high-
strength concrete beams. Structural Design of Tall and Spec Buildings 12: 1–17.
Kwan AKH, Ho JCM, Pam HJ. 2003. Effects of concrete grade and steel yield strength on flexural ductility of
reinforced concrete beams. Computers and Structures (in press).
Kwan AKH, Ho JCM, Pam HJ. 2003. Flexural strength and ductility of reinforced concrete beams. Proceedings
of the Institution of Civil Engineers, Structures and Buildings 152: 361–369.
Pam HJ, Kwan AKH, Ho JCM. 2001. Post-peak behavior and flexural ductility of doubly reinforced normal- and
high-strength concrete beams. Structural Engineering and Mechanics 12(5): 459–474.
Park R, Paulay T. 1975. Reinforced Concrete Structures. Wiley: New York.
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)
FLEXURAL STRENGTH–DUCTILITY PERFORMANCE 43
Prakash Rao DS. 1982. Design of webs and web flange connections in concrete beams under combined bending
and shear. Journal of the American Concrete Institute 79(1): 28–35.
Subedi NK. 1993. Reinforced concrete flanged beams: test and analysis. ACI Materials Journal 90(6): 601–615.
Subedi NK, Rahem A, Abdel-Rahman GT. 1992. Slender reinforced concrete flanged beams: experimental work.
Proceedings of the Institution of Civil Engineers, Structures and Buildings 94(4): 439–468.
Swamy RN, Bandyopadhyay AK, Erikitola MK. 1973. Influence of flange width on the shear behaviour of rein-
forced concrete T beams. Proceedings of the Institution of Civil Engineers, Part 1 55(2): 167–190.
NOTATION
Asc, Ast = areas of compression and tension steel reinforcement
B = breadth of beam section
Bw = breadth of the web or total breadth of the webs
b = breadth at x from neutral axis
D = effective depth of beam section
Df = depth of compression flange
D1 = depth of compression reinforcement
dn = depth of neutral axis
Es = Young’s modulus of steel reinforcement
fco = in situ uniaxial compressive strength of concrete
fyc, fyt = yield strengths of compression and tension steel reinforcement
M = moment acting on beam section
Mp = peak resisting moment of beam section
P = axial load acting on beam section
x = distance from neutral axis
e = strain in beam section
ec = strain in concrete
eco = strain in concrete at peak stress
esc, est = strains in compression and tension reinforcement
f = curvature of beam section
fu, fy = ultimate and yield curvatures of beam section
l = tension to balanced steel ratio
m = curvature ductility factor
sc = stress developed in concrete
ssc, sst = stresses developed in compression and tension reinforcement
Copyright © 2004 John Wiley & Sons, Ltd. Struct. Design Tall Spec. Build. 13, 29–43 (2004)