Académique Documents
Professionnel Documents
Culture Documents
Applied Machines: /
Machine MC-504*
DF-625
OC-512*
When installing the machine and associated options as a system, follow the order shown on the upper. Caution: For the detailed installation procedures for each option, follow the instructions given in the corresponding installation manual and perform the procedures correctly. (Optional devices must be installed after completing the main body installation.) Once the Power Switch is turned ON, do not turn OFF it until the installation work has been completed. Lifting the machine in an awkward position or transporting it in a poorly balanced position could result in personal injury. When transporting the machine, assign an adequate number of persons to the job and ensure that each person can take a good position of not being excessively loaded. <Machine mass> OC-512 and MB-505 included as standard: Approx. 29 kg (63-15/16 lb) OC-512 or MB-505 included as standard: Approx. 27.5 kg (60-5/8 lb) OC-512 and MB-505 not included as standard: Approx. 26 kg (57-5/16 lb) *OC-512: Original Cover MB-505: Multi Bypass Tray
A3PEIXC001DA
1BS0830301
E-1
A3PE-9620-00
1038 (40-7/8)
After unpacking, be sure to get rid of the packaging materials and keep them out of the reach of children. Putting the head in the plastic bag involves danger of suffocation.
1388 (54-5/8)
Note: This manual provides the illustrations of the accessory parts and machine that may be slightly different in shape from yours. In that case, instead of the illustrations, use the appearance of your machine to follow the installation procedure. This does not cause any significant change or problem with the procedure.
A3PEIXC002DA
E-2
A3PEIXC005DA
A3PEIXC006DA
A3PEIXC007DA
A3PEIXC025DA
A3PEIXC008DA
E-3
5. Unscrew the screws shown in the illustration to remove the imaging unit. (Two screws) Note: Do not touch or scratch the photoconductor. Cover the imaging unit, which has been removed, with a protective cloth or similar material.
A3PEIXC009DA
3. Open the right and front doors. 4. Remove the cover shown in the illustration and unplug the connector. (One screw)
A0XXIXC012MA
6. Close the front door. 7. Remove the protective tape. 8. Push the ends of the transfer roller shaft in the direction of the arrow to remove the fixing brackets that fix the transfer roller.
A3PEIXC010DA
A3PEIXC011DA
E-4
10. Slide out the drawer and remove the developer and cushioning material.
2. Unscrew the screws that secure the drum unit, and then take out the drum unit by slightly opening the lower part (the shadowed area) of the drum unit. (Five screws) Note: Do not open the lower part wide, otherwise the charger may drop. Do not touch or scratch the photo conductor. Cover the drum unit, which has been removed, with a protective cloth or similar material.
Developer
A3PEIXC012DA
Drum unit
A0XXIXC014MA
E-5
4. Ready a packet of the developer and cut off one corner of the aluminum packet with scissors. 5. While turning the gear in the direction of the arrow, pour the developer evenly into the developer chamber. Note: Turn the magnet roller in the direction of its normal rotation, and not the backward. Be sure not to let the developer get inside the collar. Collar
7. Install the front of the drum unit first, and then the rear part. Then, secure the screws. (Five screws) Note: Do not open the lower part wide, otherwise the charger may drop. Clean the screw groove before securing them. Do not touch or scratch the photo conductor. 8. Attach the imaging unit connector that is removed in step 1.
Temporarily tighten the screw first. Temporarily tighten the screw first.
A0XXIXC015MA
6. Reinstall the developing unit cover, ensuring that its tabs are fitted properly into the slits. (Three screws) Note: Do not tilt the developing unit or imaging unit after the developer is poured. Temporarily tighten the screw first.
A0XXIXC017MA
9. Slide the imaging unit into the machine, and then secure the screws. (Two screws) Note: Make sure that the right door is open when sliding the imaging unit into the machine. Align the shaft of the imaging unit with the guide of the machine.
A0XXIXC016MA
A0XXIXC019MA
E-6
10. Plug the connector, and then attach the cover. (One screw)
A3PEIXC014DA
Tape
A3PEIXC003DA
E-7
4. Aligning the tip of the bottle tab with the mark, insert the toner bottle all the way in. 5. Check that the toner bottle is all the way in, and then turn the toner bottle in the direction of the arrow to lock it.
A0XXIXC050MA
A3PEIXC004DA
A3PEIXC024DA
E-8