Académique Documents
Professionnel Documents
Culture Documents
UNIT MASONRY
1. PART 1 - GENERAL
1.01 SECTION INCLUDES
A.
1.02 REFERENCES
A.
B.
C.
ASTM A 153
ASTM C 33
ASTM C 90
Specification
for
Hollow
Concrete Masonry Units
Load-Bearing
ASTM C 144
Specification
Mortar
for
ASTM C 150
ASTM C 207
Specification
for
Masonry Purposes
ASTM C 270
ASTM C 426
ASTM E 149
for
Aggregate
Steel
Hydrated
Wire
Masonry
Lime
for
Concrete
Building
SSA 145
SSA 186
1.03 SUBMITTALS
A.
B.
C.
drawings
profiles
unit
B.
C.
Unit Masonry
2.
D.
Concrete
Unit
Masonry:
Test
for
strength, weight and water absorption.
compressive
2. PART 2 - PRODUCTS
2.01 MATERIALS
A.
masonry
of uniform
required
and
2.
3.
04200-3
Unit Masonry
B.
C.
3.
4.
5.
2.
3.
4.
5.
Coarse
Grout:
Consist
of
fine
and
coarse
aggregates conforming to ASTM C 404, size No. 89.
6.
Water: Clean,
materials.
potable
and
free
of
deleterious
2.
3.
Type
for
04200-4
Unit Masonry
D.
4.
5.
Do
not
add
air-entraining
agents
or
other
admixtures
to
mortar
or
grout
materials unless otherwise indicated
on
Drawings
or instructed by the Engineer.
6.
Reinforcing Bars
1.
E.
Masonry Accessories
1.
(2)
2.
3.
b.
slots
as
with
filler
strips,
hot-dip
galvanized
04200-5
Unit Masonry
above.
c.
4.
3. PART 3 - EXECUTION
3.01 INSTALLATION
A.
B.
C.
D.
Cut
E.
F.
masonry
units
with motor-driven
saws
to
provide clean, sharp, un-chipped
edges. Cut units as required to
provide
continuous
pattern
and to fit adjoining
construction. Use full-size units without cutting where
possible.
Unit Masonry
04200-6
Unit Masonry
G.
Lay-up
walls
to
comply
with
specified construction
tolerances,
with
courses
accurately
spaced
coordinated with other construction.
and
H.
I.
Fill
space
between
hollow
masonry solidly with mortar.
metal
frames
and
2.
J.
K.
2.
3.
4.
04200-7
Unit Masonry
L.
M.
5.
6.
2.
For
single-width
walls,
space
continuous
horizontal reinforcement at 400 mm on center,
unless otherwise indicated on Drawings.
3.
Control Joints
1.
Provide
control
joints
in
block
partitions, finished
or
unfinished
at
not
more than 6
m on
centers unless indicate otherwise on Drawings.
2.
Unit Masonry
N.
O.
3.
4.
Top
dress
control
joints
with
a
sealant
conforming to the requirements of Section 07900 SEALANTS. Color of sealant shall be as selected
and approved by the Engineer.
2.
b.
c.
Lintels
1.
2.
3.
4.
Unless otherwise
for each 100 mm
number not less
meter of opening
5.
04200-9
Unit Masonry
U-shaped
lintel
units
with
reinforcing
bars
placed as shown and filled with Type M mortar or
coarse grout.
6.
B.
C.
3.03 CURING
A.
When temperature
of a masonry wall
the wall
unit
sack or
days.
END OF SECTION
Unit Masonry
04200-10
Unit Masonry