Vous êtes sur la page 1sur 21

Objective

Know How To Drive Test Initial Tuning Know Software for Initial Tuning : mcom , katherein scala, static analyzer Know Initial Tuning Report

INITIAL TUNING

Preparation
Software :
- Tems Investigation 4 - Map Info - MCOM - Kathrein Scala (additional) - Static Analyzer (additional)

Tools :
- 2 Tems MS (T68) - GPS - Laptop - Camera - Other ( inverter, rigger tools)

Preparation
Basic Knowledge :
GSM Generally Drive Test (plus Scanning Freq n Time Slot Check)

Data :
Map CDD + MO (dump + process) - daily Update Kathrein Analog STS database daily update (additional)

About MCOM
Create New Project Import new mcom site Import CDD dump (neigbor+carrier) CDD Should be updated daily Check BCCH and interference Check neighbor MCOM workspace will be used as MapInfo workspace

About MCOM
Check BCCH and Interference sample

About MCOM
Check Neighboring sample

About Kathrein Scala & Katalog


Know antenna type and specification Know how antenna downtilt affects coverage area in Kathrein Scala

About Static Analyzer


Check Performance Site Basic KPI Statistic (drop rate, SDCCH success rate, handover success rate) Database Should be Updated Daily

About Static Analyzer


Sample 1 : TCH Drop Rate

BAD

GOOD

About Static Analyzer


Sample 1 : SDCCH Success Rate

BAD

GOOD

About Static Analyzer


Sample 1 : Hand Over Success Rate

BAD

GOOD

About CDD n MO
Cell Design Data (contain data such as frequency, neighboring, etc) Management Object (contain data such as site config, alarm, etc)

Initial Tuning Activity


Preparation (tools and site data) Site + Neighbors Audit and Change (Coordinate, tilt, orientation/bearing,
panorama, antenna type, height, area)

Drive Test
Tuning Site Band 900: First : MS1 = Dedicated Lock 900, MS2 : Idle Locked to BCCH, Second : MS1 = Dedicated Normal, MS2 : Idle Locked to BCCH, TS Check, Freq Scanning Tuning Site Band 1800: MS1 = Dedicated Normal, MS2 : Idle Locked to BCCH, TS Check, Freq Scanning

Report..

TimeSlot Check and Freq Scan


How?
5 minutes for Freq Scan each cells / sector 15 minutes for Time Slot Check each cells / sector using Tems Layer 3 Control

Telkomsel Freq Scan : 50-88 (900 band)


576 820 (1800 band)

Target
Target Drive Test
No Blocked Call, No HandOver Fail, No Dropped Call Good CI plot Rx Lev, Rx Qual, SQI Idle Rx Lev vs TCP Plot

Target KPI Statistik - DCR, HOSR, SDSUCC

Target Drive Test


Parameter Call Setup Success Rate Dropped Calls GSM (lock Band) 100% 0% DCS 100% 0% Note Dedicated Dedicated

HOSR Rx Qual 0 - 5

100% >= 97.00%

100% >= 98.50%

Dedicated dedicated, pada level >= -90 dBm dedicated, pada level >= -90 dBm, in Full Rate or EFR condition.

SQI >=18

>=95.00%

>=96.00%

Plot Rx Level

>=95.00%

>=95.00%

Level Idle vs TCP Plot sample

Target KPI Stats


AVERAGE VALUE SDSR HOSR TDR

Dense Urban 900 / ST DCS Dense Urban 1800 Urban 900 / ST DCS Urban 1800 Rural 900/ ST DCS Rural 1800

90,00% 93,35% 86,00% 89,20% 84,00% 91,20%

94,00% 94,85% 94,80% 97,30% 94,50% 97,50%

1,08% 0,59% 1,70% 0,81% 2,10% 1,10%

Problems
Site Down (Power?, Transmisi?) -- call Tuning Engineer / Coordinator Site On but not Servin -- call Tuning Engineer / Coordinator Cannot making call -- call Tuning Engineer / Coordinator Cannot HO (Neighbor Relation not created yet) call Tuning Engineer / Coordinator HO Failure (Interference, Co BSIC, Congestion), need parameter / frequency changing -- call Tuning Engineer / Coordinator Pingpong HO (Cross feeder, orientation problem) -- call Tuning Engineer / Coordinator Difficult HO DCS (Layer 6) to GSM (Layer 7) -- call Tuning Engineer / Coordinator Bad Quality (Interference), need frequency changing -- call Tuning Engineer / Coordinator. Low signal strength (wrong tilt / orientation) Installation Problem (cross feeder, antenna tilt n orientation), take any logfiles / photos -- call Tuning Engineer / Coordinator Coordinate problem, different between planned coordinate and actual coordinate -need any changing -- call Tuning Engineer / Coordinator Drive Test Route Problem Community Problem, Cannot access to site call Tuning Engineer / Coordinator Dll

Making Report
Export Logfiles KPI calculation (optional using macro) Plot in Map Info Others.

Vous aimerez peut-être aussi