Académique Documents
Professionnel Documents
Culture Documents
2010
CUBE-15XL
SERVICE NOTES
Issued by RJA
Table of Contents
Cautionary Notes ..............................................................2 Specifications .....................................................................2 Location of Controls .........................................................3 Location of Controls Parts List........................................3 Exploded View (Cabinet).................................................4 Exploded View (Cabinet) Parts List ...............................5 Exploded View (Chassis) .................................................6 Exploded View (Chassis) Parts List................................7 Parts List .............................................................................8 Verification of Operation ...............................................10 Block Diagram .................................................................12 Circuit Board (Main, PRE, PS1, Power Squeezer Board)................................................................................13 Circuit Diagram (Main, PRE, PS1, Power Squeezer Board)................................................................................14
Sep. 2010
CUBE-15XL
Cautionary Notes
Before beginning the procedure, please read through this document. The matters described may differ according to the model.
Specifications
CUBE-15XL: Guitar Amplifier Rated Power Output
15 W
No User Data
This product cannot save user data. Backing up user data during servicing is not required.
Part Replacement
When replacing components near the power-supply circuit or a heatgenerating circuit (such as a circuit provided with a heat sink or including a cement resistor), carry out the procedure according to the instructions with respect to the part number, direction, and attachment position (mounting so as to leave an air gap between the component and the circuit board, etc.).
Speakers
20 cm (8 inch)
Controls
[POWER] Switch [SELECT] Switch [POWER SQUEEZER] Switch <CLEAN Channel> [VOLUME] Knob TYPE Switch (OVERDRIVE, DISTORTION, METAL ZONE, EXTREME), [GAIN] Knob, [VOLUME] Knob [BASS] Knob, [MIDDLE] Knob, [TREBLE] Knob
Parts List
A component whose part code is ******** will not be supplied as a service part because one of the following reasons applies. Because it is supplied as an assembled part (under a different part code). Because a number of circuit boards are grouped together and supplied as a single circuit board (under a different part code). Because supply is prohibited due to copyright restrictions. Because reissuance is restricted. Because the part is made to order (at current market price). Because it is carried in electronic data on the Roland web site. Because it is a package or an accessory irrelevant to the function maintenance of the main body. Because it can be replaced with an article on the market. (battery or etc.)
Indicators
CLEAN Channel LEAD Channel
Connectors
INPUT Jack AUX IN Jack RECORDING OUT/PHONES Jack
Power Consumption
Circuit Diagram
In the circuit diagram, NIU is an abbreviation for Not in Use, and UnPop is an abbreviation for Unpopulated. They both mean non-mounted components. The circuit board and circuit board diagram show silk-screened indications, but no components are mounted.
18 W
Dimensions
335 (W) x 240 (D) x 335 (H) mm 13-3/16 (W) x 9-1/2 (D) x 13-3/16 (H) inches
Weight
7.1 kg / 15 lbs 11 oz
Accessories
Owners Manual Multilanguage (#5100016037) Owners Manual Chinese (#5100016325)
* 0 dBu = 0.775 Vrms * In the interest of product improvement, the specifications and/or appearance of this unit are subject to change without prior notice.
Sep. 2010
CUBE-15XL
Location of Controls
fig.panel-15XL.eps
6 10
11
12
1 2
5100016756 ROTARY POTENTIOMETER * This unit includes the following parts. 17048630 VR ACCESSORY NUT M9 40452178 VR WASHER M9 5100004351 R-KNOB
2 3
5100016755 ROTARY POTENTIOMETER * This unit includes the following parts. 17048630 VR ACCESSORY NUT M9 40452178 VR WASHER M9 5100004351 02456390 13449252 22150756 01348745 22497521R0 13449146 22150756 R-KNOB 3.5MM JACK 6.5MM JACK JACK NUT 2 SWITCH (PUSH) PUSH BUTTON 6.5MM JACK JACK NUT 2
3 4 5 6 7
5100016754 ROTARY POTENTIOMETER * This unit includes the following parts. 17048630 VR ACCESSORY NUT M9 40452178 VR WASHER M9 5100004351 03349989 03349978 R-KNOB LED (GREEN) LED (RED)
8 9 10 11
5100016825 SWITCH * This unit includes the following parts. 40128923 HEX NUT M7 17048651 VR ACCESSORY WASHER M7 5100004351 02897801 R-KNOB SEESAW SWITCH
11 12
Sep. 2010
CUBE-15XL
j 7
9 i e
g b 1
c 6 4
d a 3 e 2 8 i
Sep. 2010
CUBE-15XL
(W0804-431A) 20CM/4OHM
4 6 7 8 5
5100016544 CABINET ASSY * This unit includes the following parts. ******** CABINET 5100015010 CORNER PROTECTOR 5100015012 TRIM SASH 12359104 RUBBER FOOT SD000035 HANDLE WITH ESCUTHEON * This unit includes the following parts. 5100011381 HANDLE 5100011382 HANDLE PLATE 5100011383 HANDLE HOLDER ******** 40230789 40011689 40010367 SD000370 40010689 SD000975 SD000430 40564601 40010667 5100005098 CHASSIS ASSY SCREW 3X10 SPEED NUT M3 SCREW M4X25 PLATE WASHER SCREW 4X25 SCREW M4X35 PLANE WASHER SCREW M5X35 SCREW 4X16 SCREW 3X16
G-5R
9 a b c d e f g h i j
Sep. 2010
CUBE-15XL
12 g 4 h k 5 9 2 m d
e f 6 5 k o c
a 11 o p n j 3 b n l 1 q 8 10
Sep. 2010
CUBE-15XL
2 3 4 5 6
5100016555 MAIN BOARD ASSY * This unit includes the following parts. ******** MAIN BOARD ******** PRE BOARD ******** PS1 BOARD ******** POWER SQUEEZER BOARD SD000967 SD000968 02897801 SD000053 SD000026 5100016776 03903834 22150518 40237101 40012878 40013067 40128923 17048651 17048630 40452178 40011889 22150756 40565489 40011756 40230245 40011767 40010301 40347534 TRANSFORMER TRANSFORMER SEESAW SWITCH PCB SPACER HEATSINK FUSE FUSE STANDOFF SCREW M3X8 SCREW M3X10 SCREW M3X8 HEX NUT M7 VR ACCESSORY WASHER M7 VR ACCESSORY NUT M9 VR WASHER M9 EXTERNAL TOOTH WASHER M4 JACK NUT 2 SCREW M4X25 FLANGE HEX NUT M3 SCREW M4X12 FLANGE HEX NUT M4 SCREW M3X20 WASHER M4
8 9 10 11 12
PT BG433L 100V/117V PT BG433H 230V/240V SDDJE13200 94V-0 SCC-6 94V-0 5ST 500-R 500MA/250V (for low voltage) 5ST 250 (for high voltage) HEX.BOSS 5.5X15 M3 PAN MACHINE W/SW+SMALL PW BZC PAN MACHINE W/SW+PW ZC PAN MACHINE W/SW+SMALL PW ZC M7X12X0.5 NO.476
a b c d e f g h j k l m n o p q
FECM PLASTIC/BLK PAN MACHINE W/SW BZC ZC (except for 220VCN) PAN MACHINE W/SW+PW BZC FE ZC BINDING MACHINE BZC SPRING BZC
* Attach the No. 10 PCB Spacer from the circuit-board side using KONISHI BOND CYEREX 100 (#40231345). * Apply KS-64 SILICON GREASE (#40347934) to the No. 11 heat sink and power IC.
Sep. 2010
CUBE-15XL
Parts List
fig.-part1-e.eps
Safety Precautions: The parts marked have safety-related characteristics. Use only listed parts for replacement.
Due to one or more of the following reasons, parts with parts code ******** cannot be supplied as service parts. Part supplied only as a component in a complete assembly Copyright does not permit the part to be supplied Part is sold commercially
Note: The parts marked # are new. (initial parts) The description Qty means a necessary number of the parts per one product.
5100016544 5100016519
1 1
5100015015
CHASSIS
5100004351 22497521R0
7 2
1 2 1
1 1 1
SPEAKER
(W0804-431A) 20CM/4OHM
5100016555 MAIN BOARD ASSY * This unit includes the following parts. ******** MAIN BOARD ******** PRE BOARD ******** PS1 BOARD ******** POWER SQUEEZER BOARD
100/117V
1 1 1 1 1
03349978 03349989 POTENTIOMETER # 5100016754 # 5100016756 # 5100016757 # 5100016755 FUSE, FUSE HOLDER # 5100016776 03903834 # 5100000592
L-34HDSL-FPB L-34GDSL-FPB
1 1
2 1 2 1
1 1 2
WIRING, CABLE # # # # # #
1 1 2 1 1 1
TRANSFORMER TRANSFORMER
1 1
Sep. 2010
CUBE-15XL
AC CORD ASSY (Installed) SD000177 SD001068 # 5100012741 SD000912 5100005807 SD000914 SD000913 SD000915
AC CORD PSE AC CORD ASSY AC CORD AC CORD ASSY AC CORD AC CORD ASSY AC CORD ASSY AC CORD ASSY
SP-18A WITH TERMINAL 100V SP-18B 115V(2P) 181-BG429-BL 117VBL 2.5M SP-20 117V(2P) 181-BG429-CNLF-220VCN 2.5M SP-61 230VE(2P) SP-026A 230V(2P) SP-501 240V(2P)
for 100V for 115VTW for 117VBL for 117VU, 117VU/CS for 220VCN for 230VE for 230VEU for 240VA
1 1 1 1 1 1 1 1
SCREWS 40230789 5100005098 40010667 40010689 40013067 40237101 40012878 40010301 40230245 40010367 40565489 SD000975 40564601 40128923 22150756 40011756 40011767 40011689 17048630 SD000430 40011889 17048651 40452178 SD000370 40347534 22150518 MISCELLANEOUS # 5100015010 # 5100015012 SD000017 SD000035 5100011381 5100011382 5100011383 12359104 12369410 5100010992 5100004359 # 5100015944 # 5100015946 # 5100015945 # 5100011023 5100011022 # 5100016835 # SD000026 # 5100015949 # 5100016838 5100005099 # SD000053 # 5100005211 # 5100015942 # 5100000603 40231345 40347934 ACCESSORIES (Standard) # 5100016036 # 5100016037 # 5100016325 SCREW 3X10 SCREW 3X16 SCREW 4X16 SCREW 4X25 SCREW M3X8 SCREW M3X8 SCREW M3X10 SCREW M3X20 SCREW M4X12 SCREW M4X25 SCREW M4X25(302-P8402551LF) SCREW M4X35 SCREW M5X35 HEX NUT M7 JACK NUT 2 FLANGE HEX NUT M3 FLANGE HEX NUT M4 SPEED NUT M3 VR ACCESSORY NUT M9 PLANE WASHER EXTERNAL TOOTH WASHER M4 VR ACCESSORY WASHER M7 VR WASHER M9 PLATE WASHER WASHER M4 STANDOFF OVAL MACHINE BZC TRUSS TAPPING A BZC TRUSS TAPPING A FE BZC TRUSS TAPPING A FE BZC PAN MACHINE W/SW+SMALL PW ZC PAN MACHINE W/SW+SMALL PW BZC PAN MACHINE W/SW+PW ZC BINDING MACHINE BZC PAN MACHINE W/SW+PW BZC BINDING MACHINE BZC PAN MACHINE W/SW BZC ORIGINAL TRUSS BZC OVALHEAD MACHINE BZC PLASTIC/BLK ZC FE ZC F-TYPE D11 D4.1 T1 BLACK/323-BG-405LF FECM M7X12X0.5 NO.476 4.2X10X0.5T FEBC SPRING BZC HEX.BOSS 5.5X15 M3 2 4 24 7 7 5 1 2 3 4 2 4 2 1 2 2 3 2 6 4 1 1 6 4 2 5
CORNER PROTECTOR TRIM SASH BADGE HANDLE WITH ESCUTHEON HANDLE HANDLE PLATE HANDLE HOLDER RUBBER FOOT CORD BAND CORD COVER CORD HOOK EVA PACKING EVA PACKING EVA PACKING EVA PACKING EVA PACKING EVA PACKING HEATSINK HIMELON HIMELON LOCKING CABLE TIE PCB SPACER SEAL ACETATE TAPE TERMINAL BOND SILICON GREASE
G-5R 1702B 40285-021 25X15X1T W/ADH 85X15X1T W/ADH 85X22X1T W/ADH 110X10X1T W/ADH 110X15X1T W/ADH 268X35X1T W/ADH 6X50X0.5T W/ADH 10X270X1T W/ADH 120X2.5X1T DAIHWA SCC-6 94V-0 UL LIGHTNING FLASH #156A 35X25XT0.25 PT1870502 KONISHI BOND CYEREX100 330ML KS-64 100G
4 1 1 1 1 1 2 4 2 1 2 1 1 1 2 1 1 1 3 1 3 3 1 2 2 -
1 1 1
Sep. 2010
CUBE-15XL
5. 6. Set LEAD TYPE to METAL ZONE, and verify that the output value between the red and black speaker wires is +14.52.0 dBm. Set LEAD TYPE to EXTREME, and verify that the output value between the red and black speaker wires is +3.02.0 dBm.
Verification of Operation
Items Required
Signal generator Noise meter
Connections
For Verifying Speaker Output
Disconnect the speaker wires from the speaker, connect a 4- load resistor between the red and black wires, then connect the noise meter.
Input a 4-kHz sine wave at -60 dBm to the INPUT jack. Verify that the output value between the red and black speaker wires is +2.02.0 dBm.
3.
2. 3. 4. 5. 6. 7.
Connect the signal generator to the INPUT jack and input a 1-kHz sine wave at -40 dBm. Verify that the output value between the red and black speaker wires is +2.02.0 dBm. Connect the signal generator to the left channel of the AUX IN connector and input a 1-kHz sine wave at -20 dBm. Verify that the output value between the red and black speaker wires is 3.02.0 dBm. Connect the signal generator to the right channel of the AUX IN connector and input a 1-kHz sine wave at -20 dBm. Verify that the output value between the red and black speaker wires is 3.02.0 dBm. 4. 5. 2. 3.
Input a 100-Hz sine wave at -40 dBm to the INPUT jack. Adjust the EQUALIZER BASS control to 10, then 0, then 10, and verify that the output value between the red and black speaker wires changes as shown below. After verifying, adjust the control to 10. When at 10: When at 0: +6.52.0 dBm -1.52.0 dBm
Input a 1-kHz sine wave at -40 dBm to the INPUT jack. Adjust the EQUALIZER MIDDLE control to 10, then 0, then 10, and verify that the output value between the red and black speaker wires changes as shown below. After verifying, adjust the control to 10. When at 10: When at 0: +2.02.0 dBm -5.52.0 dBm
Input a 10-kHz sine wave at -40 dBm to the INPUT jack. Adjust the EQUALIZER TREBLE control to 10, then 0, then 10, and verify that the output value between the red and black speaker wires changes as shown below. After verifying, adjust the control to 10. When at 10: When at 0: +17.52.0 dBm +9.52.0 dBm
2. 3. 4.
Input a 300-Hz sine wave at -60 dBm to the INPUT jack. Set LEAD TYPE to OVERDRIVE, and verify that the output value between the red and black speaker wires is +1.52.0 dBm. Set LEAD TYPE to DISTORTION, and verify that the output value between the red and black speaker wires is +8.02.0 dBm.
10
CUBE-15XL
2. 3.
Input a 1-kHz sine wave at -40 dBm to the INPUT jack. Verify that the left and right output values of the PHONES jack are both at +1.52.0 dBm.
11
Sep. 2010
CUBE-15XL
Block Diagram
fig.block-15XL.eps
CLEAN VOLUME
LEAD-CH LEAD GAIN EXTREME METAL ZONE DISTORTION OVERDRIVE LEAD VOLUME
POWER AMP
SPEAKER 4
12
Sep. 2010
CUBE-15XL
13
Sep. 2010
CUBE-15XL
14
Sep. 2010
CUBE-15XL
fig.d-main.eps@R
15