Académique Documents
Professionnel Documents
Culture Documents
&""EN"ION''' $erform all (or)s onl* (hen the machine is disconnected from the mains suppl* &n* (or)s on electrical components should onl* be performed b* s)illed electricians' +&N,E- O. /I.E''
-emove the (ater tan) and ta)e off the bean container lid -emove the coffee grounds container on the left side and the drip tra* 0nscre( the t(o cross!head scre(s in the bean container In some models there ma* be an additional cover on top of the bean container funnel "his cover can onl* be removed later on 1e careful (hen reassembling as the rear scre( is longer than the one in front' Empt* the bean container using a vacuum cleaner or 2ust pour them out
&d2usting )nob for the grinding degree (regulates the fineness of grind of the coffee po(der%
"he 8,&CO9 (ater tan) seal is located under this cover -emove the cross!head scre( in the hole under the coffee bean container "he scre(driver blade must feature a length of at least : ; cm for this Other(ise *ou cannot reach the scre( through this deep hole <hen reassembling, it is easier to scre( in this scre( before putting on the cover Other(ise it is 5uite difficult to place the scre( correctl* through the hole
No( remove the t(o cross!head scre(s in the service room under the machine cover No( the upper part of the housing is loose and can be ta)en off $ull it slightl* front(ards on the left side and in the middle such that it does not collide (ith the edge of the operating unit
Slightl* shift the upper part of the housing left(ards such that the safet* catch of the hot (ater )nob
becomes visible on the right side -elease the safet* catch b* means of a pointed ob2ect and pull out the )nob
-emove the cable from the holder at the bottom side and unlatch the base plate at the openings at the bottom side of the machine b* means of a flat scre(driver
On the next picture *ou can see ho( this safet* catch loo)s inside'
$lease thoroughl* clean this gap before reassembling as remaining coffee po(der or bean particles ma* cause that the carrier plate does not latch in properl* (hen pushing the plate bac) into its position' Vie( from top into the opened machine
Power switch
&""EN"ION'
& long cross!head scre( is located here "his scre(, (hich secures the carrier plate, must be removed
Control and power electronics Solenoid of the coffee powder dosing unit The micro switch which signals if the desired powder quantit has been reached is located under this solenoid!
3=
No( ta)e the carrier plate at the bottom side of the front (approx at the height of the solenoid% and forcefull* but smoothl* pull it up(ards out of the housing &ttention' It ma* get stuc)ed a bit at the brac)et of the micro s(itch of the coffee grounds container' No( *ou have removed the carrier plate of the module from the machine and *ou have an open vie( on all components "here are no more obstacles for a repair
Vie( onto a Saeco Vienna (ithout rapid steam heating (ith boiler heating element
$%&' Pump
Cover of the bre( group drive (gear% "o reach the drive, all scre(s must be removed and the cover must be ta)en off'
#lixon temperature fuse "he pin can be pressed in again after the fuse has been triggered'
$ump pressure relief valve (old version% Supplies (ater via the "eflon tube to the boiler and discharges the excessive (ater via the thic) silicone tube into the drip tra* in case of overpressure or bloc)ings, etc '
Vie( onto a Saeco Vienna (ne( model% (ithout rapid steam heating (ith ne( instantaneous (ater heater of stainless steel
#lixon temperature fuse (? fuses in this case''% "he pin can be pressed in again after the fuse has been triggered'
"he micro s(itch including mechanical parts for the contact of the drip tra* and coffee grounds container is located here
$ump pressure relief valve (ne( version% Supplies (ater via the "eflon tube to the instantaneous (ater heater of stainless steel and discharges the excessive (ater via the thic) silicone tube into the drip tra* in case of overpressure or bloc)ings, etc '
"hermostat (#lixon% s(itches automaticall* 3:DE micro temperature fuseF if it has been triggered it is defective and needs to be replaced
Connection of the t(o fluid tubes (incoming>outgoing% (hich are fixed b* means of a suspension clamp (t(o sealing rings per tube% "he ne(er models have a scre( connection instead (self!sealing>conicall* sealing%
If *ou are not sure, do not hesitate to call us <e (ill be glad to help *ou' CD7-:4BB!B4D337B