Académique Documents
Professionnel Documents
Culture Documents
SET SCREW
PLUG
ELEMENT
PIN 3
IMPEDANCE
SELECTION SOCKET
IMPEDANCE SELECTION
RECEPTACLE END OF MICROPHONE
FIGURE 1
GENERAL
The UNISPHERE I 565 Series microphones are dual-impedance, unidirectional dynamic microphones with a strong,
wire-mesh, spherical front grille that contains a highly effective
wind and pop filter.
Shipped connected for low-impedance operation, 565 Series microphones provide excellent vocal or speech reproduction on lecterns and stages, and are a popular choice for use in
public auditoriums, churches, convention halls, and schools.
FEATURES
S Selectable dual impedance operation
S Silent magnetic reed on/off switch with lock-on option
S Cardioid dynamic
S Frequency response: 50 to 15,000 Hz
MODEL VARIATIONS
Model 565SD-CN: Supplied with 6.1 m (20 ft) XLR cable.
Model 565SD-LC: No cable supplied.
CONNECTIONS
When using the microphone with a balanced input, pins 2
and 3 are the audio signal carriers. When using the microphone
with an unbalanced input, use a cable wired with pin 2 as the signal carrier and pin 3 connected to the cable shield (ground),
such as the Shure C20HZ high-impedance cable.
IMPEDANCE SELECTION
The microphone is shipped connected for low impedance
operation. To change to high impedance, proceed as follows
(refer to Figure 1):
1. Remove plug element at receptacle end of microphone by
turning slotted setscrew in (counterclockwise) and carefully
withdrawing plug element from case.
2. Disconnect 2-terminal impedance selection socket from
rear of plug element.
3. Reconnect 2-terminal impedance selection socket in reverse position so that pin 3 of plug element is inserted in
socket terminal H (White).
4. Reassemble plug element into microphone and seal setscrew securely by turning out (clockwise).
POLARITY
All cables and microphones should be tested to ensure
that they have the same polarity. To test two microphones
and/or their cables for proper polarity, connect them to an amplifier and talk or sing into them while holding them three or four
inches apart. The sound from the speakers should be the same
when talking into either microphone or directly between them.
If the sound drops drastically, or if a dead spot is found when
talking between the two microphones, either the microphones
or their cables have opposite polarity.
To change the polarity of a microphone cable, either use
a Shure A15PRS phase reverser or interchange the wires connected to pins 2 and 3 of the three-pin connector at one end of
the cable. To change the polarity of a microphone, the microphone cartridge leads must be interchanged. This should be
performed by your dealer, the Shure Factory Service Department, or other qualified service personnel.
SPECIFICATIONS
Type
Dynamic
Frequency Response
50 to 15,000 Hz (see Figure 2)
Polar Pattern
Cardioid (unidirectional)uniform with frequency, symmetrical about axis (see Figure 3)
lmpedance
Dual. Microphone rating impedance is 150 ohms (250
ohms actual) for connection to microphone inputs rated
at 19 to 300 ohms and High for connection to high-impedance microphone inputs.
Wired for low impedance as supplied. To change impedance, see sections on lmpedance Selection and Connections.
Output Level (at 1,000 Hz)
L
H
Open Circuit Voltage* . . . . . . . . . . 56.0dB
34.0 dB
(1.6 mV)
(20 mV)
*0 dB = 1 volt per Pascal (1 Pa = 94 dB SPL)
Printed in Mexico
OPTIONAL ACCESSORIES
Line Matching Transformer . . . . . . . . . . . . . . . . . . A95 Series
Desk Stand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . S37A, S39A
Isolation Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A55M
Dual Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A26M
Windscreen . . . . . . . . . . . . . . . . . . . . . . . . . . . A58WS Series
Cable, LOZ (7.6 m [25 ft]) . . . . . . . . . . . . . . . . . . . . . . . C25J
Cable, HI-Z (6.1 m [20 ft]) . . . . . . . . . . . . . . . . . . . . . . C20HZ
ARCHITECTS SPECIFICATIONS
The microphone shall be a moving coil (dynamic) type with
a frequency response of 50 to 15,000 Hz. The unit shall have
a cardioid polar characteristic. The cancellation at the sides
shall be approximately 6 dB, and the cancellation at the rear
shall be 15 to 20 dB. The microphone shall be dual impedance
with a rated impedance of 150 ohms for connection to microphone inputs rated at 19 to 300 ohms and High for connection
to highimpedance microphone inputs. lmpedance change
shall be solderless at the microphone connector.
The microphone output shall be:
Low lmpedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56.0 dB
(0 dB = 1 volt per Pascal)
High lmpedance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34.0 dB
(0 dB = 1 volt per Pascal)
The microphone shall have an XLR, threepin professional
audio connector and shall be equipped with a magnetic reed
OnOff switch.
The microphone shall be provided with a swivel adapter,
adjustable through 90_ from vertical to horizontal, and suitable
for mounting on a stand having a 5/827 thread.
The overall dimensions of the microphone shall be 162 mm
(623/64 in.) in length and 51 mm (2 in.) in diameter.
The microphone shall be the Shure Model 565SD-LC,
565SD-CN, or equivalent.
Polarity
Positive pressure on diaphragm produces positive voltage on pin 2 (with respect to pin 3). See Figure 4.
Switch
Built-in magnetic reed on/off switch with lockplate. To
lock switch in the ON position, remove screw on
lockplate and turn lockplate 180_. Reassemble and tighten screw.
Cartridge Shock Mount
Internal rubber vibration-isolator
Cable
565SD-CN: 6.1 m (20 ft) two-conductor shielded, rubberjacketed, detachable, with XLR connectors.
Swivel Adapter
Positive action, adjustable through 90_ from vertical to
horizontal, permits easy removal for handheld use, suitable for mounting on stand with 5/827 thread
Case
Chrome-plated die casting with steel mesh grille
Dimensions
See Figure 5
Net Weight (less cable)
298 grams (10 1/2 oz)
CERTIFICATIONS
Eligible to bear CE Marking. Conforms to European EMC
Directive 89/336/EEC. Meets applicable tests and performance criteria in European Standard EN55103 (1996) parts 1
and 2, for residential (E1) and light industrial (E2) environments.
FURNISHED ACCESSORY
Swivel Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A25D
REPLACEMENT PARTS
Cartridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R65
Screen and Grille . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS65
Plug Element . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK169P
180o
150o
150o
120o
dB
20
50
100
TRANSFORMER
GREEN
YELLOW
5 dB
30o
30o
30o
0
2000 Hz
4000 Hz
8000 Hz
161 mm
(6 7/16 in.)
XLR CONNECTOR
22 mm
(7/8 in.)
93 mm
(3 11/16 in.)
RED
51 mm
(2 in.)
WHITE
YELLOW
60o
10 dB
BLUE
BLACK
60o
125 Hz
500 Hz
1000 Hz
CODED TERMINAL
GREEN
15 dB
60o
10 dB
Hz
CARTRIDGE
90o
20 dB
30o
REED
SWITCH
90o
5 dB
3 4 5 6 7 89
10000 20000
150o
120o
15 dB
10
3 4 5 6 7 89
1000
90o
60o
180o
120o
20 dB
120o
90o
+10
150o
23 mm
(15/16 in.)
BLACK
IMPEDANCE SELECTION SOCKET
(SHOWN IN LOW IMPEDANCE POSITION)
34 mm
(1 11/32 in.)
OVERALL DIMENSIONS
FIGURE 5
INTERNAL CONNECTIONS
FIGURE 4
2
GNRALITS
Les UNISPHERE I srie 565 sont des microphones lectrodynamiques unidirectionnels double impdance, munis dun
grille sphrique rsistante contenant un filtre trs efficace
contre le vent et le bruit.
Tous les cbles et tous les microphones doivent tre tests pour vrifier quils ont la mme polarit. Pour tester la polarit de deux microphones et/ou de leurs cbles, les brancher
un amplificateur et parler ou chanter en les tenant carts denviron 8 10 cm. Le son en provenance des hautparleurs doit
tre le mme quand on parle dans lun ou lautre des microphones ou directement entre eux. Si le son baisse de faon significative ou si une zone morte est dtecte lorsquon parle entre
les deux microphones, ces derniers ou leurs cbles ont une polarit oppose.
Livrs pour une utilisation en basse impdance, les microphones srie 565 permettent une excellente reproduction des
chants et de la parole sur pupitres et scnes ; ils sont une solution apprcie pour les salles dauditions, les lieux de cultes, les
salles de congrs et les coles.
AVANTAGES
S
S
Dynamique cardiode
VARIANTES
Modle 565SDCN : Fourni avec un cble XLR de 6,1 m.
CARACTRISTIQUES
Type
Dynamique
BRANCHEMENTS
Si le microphone est utilis sur une entre symtrique, les
broches 2 et 3 sont les porteuses du signal audio. Si le microphone est utilis sur une entre asymtrique, le cble doit tre
connect la broche 2 en tant que porteuse du signal et la broche 3 doit tre branche au blindage du cble (masse), telle que
le cble Shure C20HZ haute impdance.
Rponse en frquence
50 15 000 Hz (voir Figure 2)
dB
SLECTION DE LIMPDANCE
Le microphone est livr pour une utilisation en basse impdance. Pour passer une haute impdance, procder comme suit (consulter la figure 1):
1.
2.
3.
4.
10
+10
20
50
100
3 4 5 6 7 89
1000
3 4 5 6 7 89
10000 20000
Hz
VIS DARRT
150o
120o
150o
120o
180o
150o
120o
120o
LMENT
FICHE
90o
90o
90o
90o
20 dB
20 dB
15 dB
60o
15 dB
60o
10 dB
60o
30o
5 dB
30o
0
125 Hz
500 Hz
1000 Hz
BROCHE 3
PRISE DE SLECTION
DIMPDANCE
SLECTION DE LIMPDANCE
PRISE FEMELLE DU MICROPHONE
FIGURE 1
30o
30o
0
2000 Hz
4000 Hz
8000 Hz
60o
10 dB
5 dB
lmpdance
Double. Limpdance nominale du microphone est de
150 ohms (250 ohms rels) pour le branchement des
entres microphone aux valeurs nominales comprises
entre 19 et 300 ohms et de type Haute impdance pour
branchement des entres microphone haute impdance.
Fourni cbl pour impdance basse. Pour changer limpdance, consulter les sections Slection de limpdance
et Branchements
ACCESSOIRES EN OPTION
Transformateur dadaptation de ligne . . . . . . . . . . Srie A95
Socle de pupitre S37A, S39A
Silentbloc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A55M
Bonnette . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Srie A58WS
Montage jumel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A26M
Cble, LOZ (7,6 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . C25J
Cble, HIZ (6.1 m) . . . . . . . . . . . . . . . . . . . . . . . . . . . C20HZ
L (Basse) H (Haute)
Tension de circuit ouvert* . . . . 56,0 dB
34,0 dB
(1,6 mV)
(20 mV)
*0 dB = 1 volt par Pascal (1 Pa = 94 dB NPA)
Polarit
Une pression acoustique positive sur le diaphragme produit une tension positive sur la broche 2 par rapport la
broche 3. Voir Figure 5.
Interrupteur
Interrupteur intgr marchearrt lame magntique
avec plaque de verrouillage. Pour verrouiller linterrupteur sur la position MARCHE, retirer la vis de la plaque
de verrouillage et tourner la plaque de 180 degrs. Remonter et resserrer la vis.
CARACTRISTIQUES DARCHITECTURE
Le microphone est de type bobine mobile (dynamique)
avec une rponse en frquence comprise entre 50 et 15 000 Hz.
Lunit est munie dune configuration polaire cardioque. Le facteur de rjection des cts doit tre denviron 6 db et le facteur
de rjection larrire doit tre compris entre 15 et 20 dB. Le
microphone est double impdance avec une impdance nominale de 150 ohms pour le branchement aux entres microphone dont la valeur nominale est comprise entre 19 et 300
ohms et de type Haute impdance pour un branchement des
entres microphone haute impdance. Le changement dimpdance doit tre sans soudure au connecteur du microphone.
Corps
Moulage chrom avec grille ARMO-DUR et cran en
acier inoxydable
Dimensions
Voir Figure 4
161 mm
22 mm
Les dimensions horstout du microphone sont les suivantes : 162 mm en longueur et 51 mm de diamtre.
93.3 mm
23.2 mm
51 mm
INTERRUPTEUR
LAME
CAPSULE
TRANSFORMATEUR
BORNE CODE
33.9 mm
VERT
NOIR
BLEU
JAUNE
BLANC
NOIR
VERT
ROUGE
JAUNE
NOIR
HOMOLOGATION
BRANCHEMENTS INTERNES
FIGURE 5
POLARITT
Smtliche Kabel und Mikrofone sollten geprft werden,
um sicherzustellen, da sie dieselbe Polaritt aufweisen. Zum
Prfen zweier Mikrofone und/oder ihrer Kabel auf richtige Polaritt werden diese an einem Verstrker angeschlossen; dann in
die Mikrofone sprechen oder singen, wobei sie 7 bis 10 cm auseinandergehalten werden. Der von den Lautsprechern ausgehende Ton mu derselbe sein, ganz gleich, ob in eines der beiden Mikrofone oder direkt zwischen ihnen gesprochen wird.
Falls der Ton erheblich abfllt oder wenn beim Sprechen zwischen den beiden Mikrofonen ein toter Punkt festgestellt wird,
weisen entweder die Mikrofone oder ihre Kabel umgekehrte Polaritt auf.
TECHNISCHE EIGENSCHAFTEN
S Whlbarer Doppelimpedanzbetrieb
S Lautloser magnetischer Ein/AusZungenschalter mit wahlweiser Sperrvorrichtung
S Dynamisches Nierenmikrofon
S Frequenzgang: 50 bis 15.000 Hz
MODELLVARIANTEN
Modell 565SDCN: Wird mit 6,1 mXLRKabel geliefert.
Modell 565SDLC: Kabel nicht im Lieferumfang.
ANSCHLSSE
Bei Verwendung des Mikrofons an einem symmetrischen
Eingang fhren die Pins 2 und 3 das Tonsignal. Bei Verwendung
des Mikrofons an einem unsymmetrischen Eingang ein mit Pin
2 verdrahtetes Kabel als Signaltrger verwenden und Pin 3 an
die Kabelabschirmung (Masse), wie z.B. das hochohmige Kabel Shure C20HZ, anschlieen.
TECHNISCHE DATEN
Typ
Dynamisch (Tauchspule)
Frequenzgang
50 bis 15.000 Hz (siehe Abbildung 2)
dB
10
+10
IMPEDANZAUSWAHL
Das Mikrofon wird beim Versand fr niederohmigen Betrieb geschaltet. Zum Umschalten auf hochohmigen Betrieb wie
folgt vorgehen (siehe Abb. 1):
1. Das Steckelement am Buchsenende des Mikrofons entfernen, indem die geschlitzte Stellschraube nach innen (gegen den Uhrzeigersinn) gedreht wird und das Steckelement vorsichtig aus dem Gehuse gezogen wird.
2. Den Impedanzwahlsockel mit 2 Anschluklemmen vom
hinteren Teil des Steckelements abnehmen.
3. Den Impedanzwahlsockel mit 2 Anschluklemmen in umgekehrter Lage wieder anschlieen, so da Pin 3 des Stekkelements in die Sockelklemme H (Wei) eingesteckt
wird.
4. Das Steckelement wieder in das Mikrofon einbauen und die
Stellschraube sicher festziehen, indem sie nach auen (im
Uhrzeigersinn) gedreht wird.
20
50
100
3 4 5 6 7 89
1000
3 4 5 6 7 89
10000 20000
Hz
TYPISCHER FREQUENZGANG
ABBILDUNG 2
Richtcharakteristik
Nierencharakteristik (unidirektional)mit gleichfrmigem
Frequenzgang und Achsensymmetrie (siehe Abbildung 3)
180o
150o
150o
150o
180o
150o
STELLSCHRAUBE
120o
120o
120o
120o
STECKELEMENT
90o
90o
90o
90o
20 dB
20 dB
15 dB
60o
15 dB
60o
10 dB
60o
5 dB
30o
5 dB
30o
0
125 Hz
500 Hz
1000 Hz
PIN 3
IMPEDANZAUSWAHLSOCKEL
IMPEDANZAUSWAHL
BUCHSENENDE DES MIKROFONS
ABBILDUNG 1
30o
30o
0
2000 Hz
4000 Hz
8000 Hz
TYPISCHE RICHTCHARAKTERISTIKEN
ABBILDUNG 3
5
60o
10 dB
MITGELIEFERTES ZUBEHR
lmpedanz
Die Nennimpedanz des Doppelimpedanzmikrofons betrgt 150 Ohm (Istwert: 250 Ohm) beim Anschlu an Mikrofoneingnge mit Nennimpedanzen von 19 bis 300
Ohm und hochohmig beim Anschlu an hochohmige
Mikrofoneingnge.
Im Lieferzustand auf niederohmigen Betrieb geschaltet.
Zum ndern der Impedanz siehe die Abschnitte Impedanzauswahl und Anschlsse.
Schwenkadapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A25D
ERSATZTEILE
Kapsel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R65
Filter und Grill . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS65
Steckelement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RK169P
SONDERZUBEHR
L
H
Leerlaufspannung* . . . . . . . . . . . 56,0 dB
34,0 dB
(1,6 mV)
(20 mV)
*0 dB = 1 Volt je Pascal (1 Pa = 94 dB Schalldruckpegel)
Polaritt
Positiver Druck an der Membran erzeugt positive Spannung an Pin 2 (in bezug auf Pin 3). Siehe Abbildung 5.
Schalter
Integrierter magnetischer Ein/AusZungenschalter mit
Sperrvorrichtung. Zum Sperren des Schalters in der Stellung ON, die Schraube an der Verriegelungsplatte entfernen und die Verriegelungsplatte um 180_ drehen. Wieder
zusammenbauen und die Schraube festziehen.
KONSTRUKTIONSDATEN
Das Mikrofon ist ein (dynamisches) Tauchspulenmikrofon
mit einem Frequenzgang von 50 bis 15.000 Hz. Das Mikrofon
weist eine Nierenrichtcharakteristik auf. Die Unterdrckung betrgt an den Seiten ungefhr 6 dB und an der Rckseite ungefhr 15 bis 20 dB. Bei dem Mikrofon handelt es sich um ein Doppelimpedanzmikrofon mit einer Nennimpedanz von 150 Ohm
beim Anschlu an Mikrofoneingnge mit Nennimpedanzen von
19 bis 300 Ohm und hochohmig beim Anschlu an hochohmige Mikrofoneingnge. Die Impedanznderung erfolgt ltfrei am
Mikrofonanschlu.
Kapselschwingungsdmpfung
Eingebauter Gummischwingungsdmpfer
Kabel
565SDCN: 6,1 m langes zweipoliges, abgeschirmtes,
gummiumhlltes, abnehmbares Kabel mit XLRStekkern.
Schwenkadapter
Formschlssig, im 90_Bereich von der Senkrechten zur
Waagerechten einstellbar; ermglicht einfaches Abnehmen zum Handgebrauch, eignet sich zur Montage auf
einem Stativ mit 5/827Gewinde.
niederohmig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56,0 dB
(0 dB = 1 Volt je Pascal)
hochohmig . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34,0 dB
(0 dB = 1 Volt je Pascal)
Das Mikrofon verfgt ber einen dreipoligen XLRTonstekker und ist mit einem magnetischen Ein/AusZungenschalter
ausgestattet.
Gehuse
Verchromtes Spritzgugehuse mit ARMODURGrill
und EdelstahlAbschirmung
Abmessungen
Siehe Abbildung 4.
161 mm
22 mm
93.3 mm
23.2 mm
51 mm
KAPSEL
ZUNGENSCHALTER
33.9 mm
TRANSFORMATOR
XLRSTECKER
CODIERTER ANSCHLUSS
GESAMTABMESSUNGEN
ABBILDUNG 4
GRN
GRN
ROT
BLAU
SCHWARZ
GELB
ZERTIFIZIERUNG
WEISS
SCHWARZ
GELB
SCHWARZ
INTERNE ANSCHLSSE
ABBILDUNG 5
6
GENERALIDADES
Los UNISPHERE I serie 565 son micrfonos dinmicos unidireccionales de impedancia doble con una rejilla esfrica de
malla de alambre que contiene un filtro contra viento y chasquidos sumamente eficaz.
Los micrfonos de la serie 565 se suministran configurados
para conexin de baja impedancia y proporcionan una reproduccin excelente para oradores o cantantes en atriles o escenarios y son una alternativa popular para uso en auditorios pblicos, iglesias, salas de convencin y escuelas.
Someta todos los cables y micrfonos a prueba para asegurarse que tengan la misma polaridad. Para probar la polaridad
de dos micrfonos y/o sus cables, conctelos a un amplificador
y hable o cante por ellos mientras los mantiene separados entre
s de 8 a 10 cm. El sonido reproducido por los altavoces debe
ser igual al hablar por cualquiera de los micrfonos, o en un
punto entre ellos. Si el sonido pierde intensidad de modo significativo, o si se descubre un punto muerto al hablar entre los dos
micrfonos, los micrfonos o sus cables tienen polaridades
opuestas.
CARACTERISTICAS
S Seleccin de dos configuraciones de impedancia
S Silencioso interruptor de activacin de lengeta magntica
con bloqueo opcional
S Dinmico, patrn de captacin de cardioide
S Respuesta de frecuencia: 50 a 15.000 Hz
VARIEDADES DE MODELOS
Modelo 565SDCN: Suministrado con cable tipo XLR de
6,1 m de largo
Modelo 565SDLC: Se suministra sin cable.
ESPECIFICACIONES
Tipo
Dinmico
CONEXIONES
Cuando se usa el micrfono con una entrada equilibrada,
las clavijas 2 y 3 portan la seal de audio. Cuando se usa el micrfono con una entrada desequilibrada, use un cable y conector cuya clavija 2 porte la seal y cuya clavija 3 se conecte al
blindaje del cable (tierra), tal como el cable Shure C20HZ de alta impedancia.
Respuesta de frecuencia
50 a 15.000 Hz (vea la Figura 2)
dB
10
+10
20
50
100
3 4 5 6 7 89
1000
3 4 5 6 7 89
10000 20000
Hz
Patrn polar
Cardioide (unidireccional) uniforme respecto a la frecuencia, simtrico respecto al eje del micrfono (vea la
Figura 3)
180o
150o
TORNILLO DE FIJACION
150o
120o
150o
120o
180o
150o
120o
120o
ELEMENTO DEL
ENCHUFE
90o
90o
90o
90o
20 dB
20 dB
15 dB
60o
15 dB
60o
10 dB
60o
30o
5 dB
30o
0
125 Hz
500 Hz
1000 Hz
CLAVIJA 3
PUENTE SELECTOR DE
IMPEDANCIA
SELECCION DE IMPEDANCIA
EXTREMO DEL RECEPTACULO DEL MICROFONO
FIGURA 1
60o
10 dB
5 dB
30o
30o
0
2000 Hz
4000 Hz
8000 Hz
Impedancia
Doble. La impedancia nominal del micrfono es de 150
ohmios (250 ohmios real) para conectarlo a enchufes de
entrada con impedancia nominal de 19 a 300 ohmios y la
impedancia es alta para conectarlo a enchufes de entrada de alta impedancia.
Se despacha configurado para conexin de baja impedancia. Para cambiar la impedancia, vea las secciones
Seleccin de nivel de impedancia y Conexiones.
ACCESORIO SUMINISTRADO
Adaptador giratorio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A25D
REPUESTOS
Cpsula . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . R65
Malla y rejilla . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS65
Elemento del enchufe . . . . . . . . . . . . . . . . . . . . . . . . . RK169P
ACCESORIOS OPCIONALES
Transformador de impedancia . . . . . . . . . . . . . . . . Serie A95
Pedestal de escritorio . . . . . . . . . . . . . . . . . . . . . . S37A, S39A
Montaje con aislamiento . . . . . . . . . . . . . . . . . . . . . . . . A55M
Pantalla . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Serie A58WS
Montaje doble . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A26M
Cable de baja impedancia (7,6 m) . . . . . . . . . . . . . . . . . C25J
Cable de alta impedancia (6,1 m) . . . . . . . . . . . . . . . . C20HZ
Alta (H)
Caja
Moldeado a troquel con chapado en cromo, rejilla
ARMODUR y malla de acero inoxidable.
Dimensiones
Vea la Figura 4
161 mm
22 mm
93.3 mm
51 mm
23.2 mm
INTERRUPTOR
DE LENGETA
DIMENSIONES GENERALES
FIGURA 4
CAPSULA
TRANSFORMADOR
CONECTOR XLR
BORNE CIFRADO
VERDE
VERDE
ROJO
AZUL
NEGRO
BLANCO
AMARILLO
AMARILLO
NEGRO
NEGRO
CERTIFICACIONES
Califica para llevar las marcas CE. Cumple la directiva europea 89/336/EEC de compatibilidad electromagntica. Se ajusta a los criterios correspondientes de verificacin y funcionamiento establecidos en la norma europea EN 55103 (1996),
CONEXIONES INTERNAS
FIGURA 5
8
POLARIT
Tutti i cavi e i microfoni devono essere provati per verificare che abbiano la stessa polarit. Per provare due microfoni o
i rispettivi cavi (o i microfoni e i cavi allo stesso tempo), collegateli ad un amplificatore e parlate o cantate tenendo i microfoni
a 710 centimetri di distanza luno dallaltro. Il suono emesso
dai diffusori deve essere lo stesso sia che si parli verso luno o
laltro microfono sia che si parli direttamente tra di essi. Se il volume diminuisce notevolmente o si rileva una zona morta quando si parla tra i microfoni, questi o i cavi hanno polarit opposta.
I microfoni serie 565 sono spediti con la connessione pronta per il funzionamento a bassa impedenza, permettono riproduzioni di grande qualit del suono di oratori e cantanti e costituiscono una scelta diffusa per auditori, chiese, sale da riunione
e scuole.
CARATTERISTICHE
S
DATI TECNICI
Tipo
Dinamico
Risposta in frequenza
Da 50 Hz a 15.000 kHz (vedi Figura 2)
dB
+10
SELEZIONE DELLIMPEDENZA
Il microfono spedito con la connessione pronta per il funzionamento a bassa impedenza. Per selezionare limpedenza
alta, procedete come segue (vedi Figura 1):
1.
2.
3.
4.
10
20
50
100
3 4 5 6 7 89
1000
3 4 5 6 7 89
10000 20000
Hz
Diagramma polare
Cardioide (unidirezionale), uniforme in frequenza, simmetrico rispetto allasse (vedi Figura 3)
180o
150o
150o
150o
180o
150o
VITE DI FERMO
ZOCCOLO DI SELEZIONE
IMPEDENZA
120o
ELEMENTO
A SPINA
120o
90o
90o
120o
120o
90o
90o
20 dB
20 dB
15 dB
60o
15 dB
60o
10 dB
60o
30o
5 dB
30o
30o
PIEDINO 3
125 Hz
500 Hz
1000 Hz
SELEZIONE DELLIMPEDENZA
ESTREMIT PER IL CONNETTORE NELLA PARTE TERMINALE DEL MICROFONO
FIGURA 1
60o
10 dB
5 dB
30o
0
2000 Hz
4000 Hz
8000 Hz
ACCESSORI IN DOTAZIONE
lmpedenza
Doppia. Limpedenza nominale uguale a 150 ohm (250
ohm effettivi) per collegamenti ad ingressi microfonici
con impedenza compresa tra 19 e 300 ohm; ed High
(Alta) per collegamenti ad ingressi ad alta impedenza.
Alla spedizione la connessione stata eseguita per il
funzionamento a bassa impedenza. Per cambiare impedenza, seguite le istruzioni riportate nella sezione corrispondente.
Alto
34,0 dB
(20 mV)
Polarit
Una pressione sonora positiva sul diaframma produce
una tensione positiva sul piedino 2 rispetto al piedino 3.
Vedi Figura 5.
Interruttore
On/off, con rel reed che ne assicura la silenziosit, e
placca di bloccaggio. Per bloccare linterruttore in posizione on, togliete la vite della piastra e girate questultima
di 180 gradi. Non dimenticate di riavvitare la vite.
SPECIFICHE DI PROGETTAZIONE
Il microfono a bobina mobile (dinamico) con risposta in
frequenza compresa tra 50 e 15.000 Hz. Il diagramma polare
cardioide. La cancellazione laterale uguale a circa 6 dB e la
cancellazione sulla parte posteriore compresa tra 15 e 20 dB.
Il microfono a doppia impedenza. Limpedenza nominale
uguale a 150 ohm, per collegamenti ad ingressi microfonici
con impedenza tra 19 e 300 ohm; e pu avere valore Alto se
lingresso microfonico a cui collegato ad alta impedenza.
possibile variare limpedenza invertendo il collegamento del
connettore del microfono, senza bisogno di eseguire saldature.
Involucro
Pressofuso, in cromo, placcato, con griglia ARMO
DUR e schermo di acciaio inossidabile.
Dimensioni
Vedi Figura 4.
161 mm
22 mm
93.3 mm
23.2 mm
INTERRUTTORE
REED
DIMENSIONI COMPLESSIVE
FIGURA 4
CAPSULA
TRANSFORMATORE
CONNETTORE XLR
CODED TERMINAL
VERDE
VERDE
ROSSO
BLU
NERO
BIANCO
GIALLO
CERTIFICAZIONI
Contrassegnabile con il marchio CE. Conforme alla direttiva europea sulla compatibilit elettromagnetica 89/336/CEE.
Conforme ai criteri sulle prestazioni e alle prove pertinenti specificati nella norma europea EN 55103 (1996) parti 1 e 2, per
ambienti residenziali (E1) e industriali leggeri (E2).
GIALLO
NERO
NERO
ZOCCOLO DI SELEZIONE IMPEDENZA (ILLUSTRATO
NELLA POSIZIONE DI BASSA IMPEDENZA)
CONNESSIONI INTERNE
FIGURA 5
10
11
12