Vous êtes sur la page 1sur 3

2011 Cooper Bussmann

www.cooperbussmann.com/wireless
Description
1211 Page 1 of 3 Data Sheet # 7908 BU-SB11836
Features
150/220/400/869MHz, 5mW-5W, DFSK
(1)
, 3.6-19.2kbps radio
communications to 35m/56Km with multi-hop repeating.
(2)
Able to connect similar/dissimilar industrial protocols and vendor devices
(incorporating: Master/Slave, Slave/Slave, Master/Master networks).
Simple to complex, point to multi-point communications with forward-
error correction (FEC), data inte.g.,rity check (CRC) and data encryption.
Eight configurable digital I/O with I/O expansion via ELPRO 115S range.
AC/DC/battery power options with UPS battery charger.
Module diagnostics including read/write of re.g.,ister I/O, reporting of
signal strength indication (RSSI), communications logging and internal
measurement of low/normal and battery supply voltages.
Specifications
Transmitter/Receiver
Modulation DFSK
(1)
Transmit Power 148 - 174MHz, 0.1 - 5W
220 - 235MHz, 0.1 - 5W
360 - 512MHz, 10mW - 5W
869.525MHz, 500mW
869.875MHz, 5mW
Receiver Sensitivity 150/220/400MHz: 112dBm
869MHz: 108dBm
Data Rate 150/220/400MHz: 3.6 kbps
869MHz: 19.2kbps
Line Of Sight
Range
(2)
150/220/400MHz: 10mW EIRP to 2km,
500mW EIRP to 10km, 5W EIRP to 50km
869MHz: 5km (500mW), 1km (5mW)
Antenna Connector 150/220/400MHz: BNC female coaxial
(with gas discharge arrestor).
869MHz - SMA female (with gas discharge arrestor).
Input/Output
Onboard D I/O
(1)
Eight non voltage/FET I/O: 30Vdc/500mA
Ethernet Port - model/protocol dependent
Ethernet Port 10/100Mbps, RJ45 - IEEE802.3
LEDs Link/100Mbps
Note: Specifications subject to change.
1) DFSK - Digital Frequency Shift Key.
2) Actual radio distances dependent on terrain/obstacles. Country re.g.,ulations and
module dependant.
Continued on back.
Applications
Similar/dissimilar data-bus SCADA/
DCS to PLC-PLC communications
Moving machinery PLC-PLC/HMI
connection/operation
Data-bus cable replacement
Smart instrument interface and
connection (e.g., gas analyzer)
Multi I/O data concentrator/
repeater for large networks
105U-G Wireless Gateway
Data-bus Interface and Conversion
ELPRO wireless gateways provide the interface and communication between
industrial data-bus devices and field devices (e.g., Modbus to Profibus to
EtherNet/IP: PLCs to SCADA/DCS etc). Connected via RS232/RS485/RJ-45,
re.g.,ister allocated data-bus values are transmitted/received by radio to and
from field and control room devices.
ELPRO 105U-G series products can multi-hop repeat up to five times,
support a variety of industrial protocols and can be combined with ELPRO
105U/505U-K and 115S series products to create I/O and data-bus networks.
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehen-
sive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211 Page 2 of 3 BU-SB11836 Data Sheet # 7908
Specifications
Serial Port
RS232 9pin DB9 female connector
RS485 Terminal connector (serial expansion module option: cable
<2000m)
Data Rate
Configurable
9600 baud, 8 bits, no parity, 1 stop bit (programming)
300 - 38400, 7/8 bits, N/O/E, Parity, 1/2 Stop. Modbus/DF1
Protocols and Configuration
105U-G-MD1
Modbus RTU
(Master/Slave), DF1
Up to 4300 I/O points: analog and/or discrete
Modbus - RS232/485: 300 - 38400bps
DF1 (full duplex) - RS232: 300 - 38400bps
105U-G-ET1
EtherNet/IP (Level
2I/O Server)
Modbus/TCP (Class 0, 1: partially class 2 Slave)
TCP/IP functions; embedded web system (dynamic HTTP); on-
board file system for downloadable web pages via FTP server; email
(SMTP)
2048 bytes input/2048 bytes output: up to 4300DI/O or
1024AI/1024AO. 10/100Mbps, RJ45 connector
105U-G-PR1
Profibus DP Slave to
EN 50170 standard
416I/O bytes (up to 1952DI/ 1952DO or up to 122AI/ 122AO)
RS-485 optically isolated with onboard DC/DC converter
Automatic baud rate detection: 9600bps - 12Mbps
105U-G-PR2
Profibus DP Master
to EN 50170
standard
2048 bytes input/2048 bytes output: up to 4300 DI/O or
1024AI/1024AO
RS-485 optically isolated with onboard DC/DC converter
Automatic baud rate detection: 9600bps - 12Mbps
105U-G-DE1
DeviceNet Slave
512 bytes input/512 bytes output (up to 4300DI/O or 256AI/
256AO)
Re.g.,ister size 16 bit - number of remote 905U addresses 500
RS422 optically isolated (selectable baud rate between 125, 250,
500kbps)
105U-G-M+1
Modbus+Slave
Global database transactions: routing up to six networks
2048 bytes input/2048bytes output (up to 4300DI/O or
1024AI/1024AO) RS485 optically isolated: standard baud rate
1Mbps
User Configuration E-Series configuration utility
LED Indication
ACTIVE (ACT) Micro processer/ Module operational
OK Mains/ battery power supply available
SERIAL TX & RX Serial port transmitting; Serial port receiving
RADIO TX & RX Radio transmitting; Radio receiving
I/O LED markers I/O inputs and/or outputs status
Data-bus Interface and Conversion
105U-G Wireless Gateway
General
Size 5.1 x 7.3 x 2.4 (130 x 185 x 60mm)
Weight 2.2lbs (1Kg)
Temperature 105U-G-MD1 150/220/400MHz: -30 to +60C (-22 to 140F)
105U-G-MD1 869MHz: -40 to +60C (-40 to 140F)
105U-G-ET1/PR1/PR2/DE1/M+1: -30 to +60C (-22 to 140F)
Humidity 105U-G-MD1: RH Non-condensing 0-99%
105 U-G-ET1/PR1/PR2/DE1/M+1: RH Non-condensing 0 - 95%
Housing Extruded aluminum
Mounting DIN rail mounting
Terminal strip Removable: up to 2.5mm
2
(12AWG)
Approvals EMC: FCC Part 15, AS3548, EN 301 489
Radio: EN 300 220, FCC Part 90, RSS 119, AS4295, AS4768.1,
EN 300 113
Safety: EN 60950, Class I Division 2 hazardous areas (USA/
Canada)
Power Supply
Nominal Supply 12-24Vac/9-30Vdc: over-voltage/reverse power protected
Quiescent Current 105U-G-MD1: +12V, 150mA: 24V, 90mA: add 5mA per I/O point
105U-G-ET1/PR1/PR2/DE1/M+1: +12V, 270mA: 24V, 170mA:
add 5mA per I/O point
Transmission Current 450mA @ 13.8Vdc (0.5W)
600mA @ 13.8Vdc (1W)
800mA @ 13.8Vdc (2W)
1.25A @ 13.8Vdc (5W)
Battery Supply 11.5-15.0Vdc (battery supply volts internal I/O value)
Battery Charge
Circuit
Suitable for 12Vdc sealed lead acid batteries, max charge
current 2.0A (5W), 0.9A (500mW)
Note: Specifications subject to change.
1) Configurable as inputs/outputs.
2011 Cooper Bussmann
www.cooperbussmann.com/wireless
1211
The only controlled copy of this Data Sheet is the electronic read-only version located on the Cooper Bussmann Network Drive. All other copies of this document are by definition uncontrolled. This bulletin is intended to clearly present comprehen-
sive product data and provide technical information that will help the end user with design applications. Cooper Bussmann reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of
any products. Cooper Bussmann also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications.
Product Code Description Data
Sheet #
Antennas 148 - 174MHz
UDP150-5 Dipole Antenna: BNC Male, 0dBi gain, 16 (5m) Coaxial cable 7939
Antennas 220 - 235MHz
UDP200-C Dipole Antenna: N-type Female, 0dBi gain 7939
UDP200-3 Dipole Antenna: BNC Male, 0dBi gain, 9 (3m) Coaxial cable 7939
Antennas 360 - 512MHz
UDP400-C Dipole Antenna: BNC Male, 0dBi gain, 9 (3m) Coaxial cable 7940
UDP400-3 Dipole Antenna: N-type Female, 0dBi gain, 9 (3m) Coaxial cable 7940
YU-3/400 Yagi Antenna: 3 element, N-type, 10dBi gain 7940
YU-6/400 Yagi Antenna: 6 element, N-type, 9dBi gain 7940
YU-16/400 Yagi Antenna - 16 element, N-type, 15dBi gain 7940
BU-3/400 Collinear Antenna: N-type Female, 5dBi gain 7940
BU-6/400 Collinear Antenna: N-type Female, 8dBi gain 7940
Antennas 869MHz
CFD890EL Dipole Antenna: SMA, 2dBi, 16 (5m) RG58, bracket 7942
SG900EL Collinear Antenna: N-type Female, 5dBi gain 7942
SG900-6 Collinear Antenna: N-type Female, 8dBi gain 7942
DG800-5 Whip Antenna: SMA Male, -2dBi gain, 16 (5m) RG174, bracket 7942
YU6/870 Yagi Antenna: 6 element, N-type, 9dBi gain 7942
Cables
CC3/10/20-SMA Coaxial Cable Kit - 10 (3m)/33 (10m)/66 (20m), N-type to SMA 7932
CC10/20-BNC Coaxial Cable Kit - 33 (10m)/66 (20m), N-type to BNC 7932
CCTAIL-SMA-F/M Coaxial Cable Tail - 2 (600mm), SMA to N-type Female/Male 7932
CCTAIL-BNC-M Coaxial Cable Tail - 2 (600mm), BNC to N-type male 7932
SER-DB9 Serial RS232 Cable - DB9 male to DB9 female straight through 7932
Surge Diverters
CSD-SMA-2500 SMA Surge Diverter for use with CC10, CC20 - SMA 7936
CSD-N-6000 Coaxial Surge Divertor, Bulkhead N Female to N Female 7936
MA15/D/1/SI Power Supply Surge Diverter, 110Vac/15A 7936
IOP32/IOP32D Signal Surge Diverter, 2 wire/4 wire 7936
Power Supplies
PS-DINAC-12DC DIN Rail Power Supply, 100 - 250Vac, 12Vdc/2.5A 7935
PS-DINAC-24DC DIN Rail Power Supply, 100 - 250Vac, 24Vdc/2A 7935
Mounting Brackets
BR-YAGI-KIT Mounting Bracket Kit for Yagi Antenna 7933
BR-COL-KIT Mounting Bracket Kit for Collinear Antenna 7933
Accessories
The following accessories can assist with compatibility when commissioning.
Ordering
To order, select product code from the table and specify country of application.
Product Code Description Frequency RF Power
Industrial Protocol - Devicenet Slave
105U-G-DE1-150-5W Gateway, DeviceNet Slave 148-174MHz
(2)
0.1 - 5W
105U-G-DE1-220-5W Gateway, DeviceNet Slave 220-235MHz
(2)
0.1 - 5W
105U-G-DE1-xxx
(1)
-5W Gateway, DeviceNet Slave 360-512MHz
(2)
0.5 - 5W
105U-G-DE1-xxx
(1)
-500M Gateway, DeviceNet Slave 360-512MHz
(2)
10 - 500mW
105U-G-DE1-868-500M Gateway, DeviceNet Slave 869.525MHz 500mW
105U-G-DE1-868-5M Gateway, DeviceNet Slave 869.875MHz 5mW
Industrial Protocol - Ethernet/IP, Modbus TCP
105U-G-ET1-150-5W Gateway, Ethernet 148-174MHz
(2)
0.1 - 5W
105U-G-ET1-220-5W Gateway, Ethernet 220-235MHz
(2)
0.1 - 5W
105U-G-ET1-xxx
(1)
-5W Gateway, Ethernet 360-512MHz
(2)
0.5 - 5W
105U-G-ET1-xxx
(1)
-500M Gateway, Ethernet 360-512MHz
(2)
10 - 500mW
105U-G-ET1-868-500M Gateway, Ethernet 869.525MHz 500mW
105U-G-ET1-868-5M Gateway, Ethernet 869.875MHz 5mW
Industrial Protocol - Modbus Plus Slave
105U-G-M+1-150-5W Gateway, Modbus Plus Slave 148-174MHz
(2)
0.1 - 5W
105U-G-M+1-220-5W Gateway, Modbus Plus Slave 220-235MHz
(2)
0.1 - 5W
105U-G-M+1-xxx
(1)
-5W Gateway, Modbus Plus Slave 360-512MHz
(2)
0.5 - 5W
105U-G-M+1-xxx
(1)
-500M Gateway, Modbus Plus Slave 360-512MHz
(2)
10 - 500mW
105U-G-M+1-868-500M Gateway, Modbus Plus Slave 869.525MHz 500mW
105U-G-M+1-868-5M Gateway, Modbus Plus Slave 869.875MHz 5mW
Industrial Protocol - Modbus RTU/DF1
105U-G-MD1-150-5W Gateway, Modbus/DF1 148-174MHz
(2)
0.1 - 5W
105U-G-MD1-220-5W Gateway, Modbus/DF1 220-235MHz
(2)
0.1 - 5W
105U-G-MD1-xxx
(1)
-5W Gateway, Modbus/DF1 360-512MHz
(2)
0.5 - 5W
105U-G-MD1-xxx
(1)
-500M Gateway, Modbus/DF1 360-512MHz
(2)
10 - 500mW
105U-G-MD1-868-500M Gateway, Modbus/DF1 869.525MHz 500mW
105U-G-MD1-868-5M Gateway, Modbus/DF1 869.875MHz 5mW
Industrial Protocol - Profibus Master/Slave
105U-G-PRx
(3)
-150-5W Gateway, Probus 148-174MHz
(2)
0.1 - 5W
105U-G-PRx
(3)
-220-5W Gateway, Probus 220-235MHz
(2)
0.1 - 5W
105U-G-PRx
(3)
-xxx
(1)
-5W Gateway, Probus 360-512MHz
(2)
0.5 - 5W
105U-G-PRx
(3)
-xxx
(1)
-500M Gateway, Probus 360-512MHz
(2)
10 - 500mW
105U-G-PRx
(3)
-868-500M Gateway, Probus 869.525MHz 500mW
105U-G-PRx
(3)
-868-5M Gateway, Probus 869.875MHz 5mW
Note: Available RF power and frequency may vary depending on country of application.
1) Represents frequency band (370, 390, 410, 430, 440, 460, 480, 500).
2) Ordering code requires the frequency selected.
3) 1 - Profibus Master or 2 - Profibus Slave.
Data-bus Interface and Conversion
105U-G Wireless Gateway
Page 3 of 3 BU-SB11836 Data Sheet # 7908

Vous aimerez peut-être aussi