0 évaluation0% ont trouvé ce document utile (0 vote)
73 vues2 pages
The lock is equipped with three mechanical keys for manual lock operation. By Default, the lock is configured to grant any fingerprint access to unlock. The lock can set 4 administrators and ID number will be 96--99.
The lock is equipped with three mechanical keys for manual lock operation. By Default, the lock is configured to grant any fingerprint access to unlock. The lock can set 4 administrators and ID number will be 96--99.
The lock is equipped with three mechanical keys for manual lock operation. By Default, the lock is configured to grant any fingerprint access to unlock. The lock can set 4 administrators and ID number will be 96--99.
1. The lock is equipped with three mechanical keys for manual lock operation. Remove mechanical keys from the package and keep them in a safe place. 2. To power the lock, four alkaline AA batteries (not included) are required. The lock has low battery voltage alarm (Red LED flashes and six beeps when you active the lock) to prompt replace battery. Non-alkaline and rechargeable batteries ARE NOT RECOMMENDED. 3. By Default, the lock is configured to grant ANY fingerprint access to unlock. 4. By Default, the lock is configured can not read ID card. Please refer to RFID Card Function to enable card reading function. 5. Please avoid strong light direct to the lock. This will normally be an official in the company or the host of a family who will have administrator permissions and will be able to do various operations. The lock can set 4 administrators and ID will be 96--99. This will be a user under administrator's management who will be granted access to open the lock. The lock can set 95 normal users and ID number will be 01--95. User Operation Quick Operation Mode Normal user The Nixie tube prompting characters The LED status -- Bule LED flashes Red LED light Red LED flashes Red LED fast flashing Bule LED fast flashing Bule and Red LED flashes Long Voice Six beeps Three Beeps Two Beeps Short music voice Need administrator identification. Delete user who is identified by fingerprint or card. Delete all the users. ID range for normal users. (95 users capacity) ID range for administrators.(4 administrators capacity) Ad FP AL 01-95 96-99 Normal open function: Open the door without fingerprint or card verification on the lock, which is fit for meeting room and some places free to in or out. Enable: Verify any registered fingerprints or cards on lock and press key. Disable: Press key directly. Normal Open Function RFID Card Function: Enable this function the lock can read ID cards. The battery lifespan can be doubled after disabling the RFID Card Function. Enable: Verify any registered fingerprint on lock and press key. Disable: Verify any registered fingerprint on lock and press key. RFID Card Function Administrator L100D II/L100II Home & Business Smart Lock User Manual (V2.1) OK C 8 9 10 11 12 13 14 15 2 4 7 5 1 3 6 16 LED indicator Fingerprint sensor Card area Mechanical key hole Restart button Rubber key cover 9V emergency power terminal Battery box cover Battery area Add key Delete key Nixie tube OK Confirm Key C Cancel Key Factory Debug Port Mechanical key 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 - - Character Description Description Initialization Button Initialize The Fingerprint Lock Initializing the fingerprint lock means all of the user will be deleted and back to factory mode. Operation: The Initialization Button is in the inside panel of the lock, and holding the Initialization Button until the lock prompts the voice of initialization. When initialization is completed, the fingerprint lock will restart automaticly. Note: Fingerprint Lock Initialization must be supplied with power.
User Introduction Register User (Register user without administrator.) Structure Before Connecting, operating or adjusting this product, please read the instructions completely. Keep this manual you will need it again. is registered trademark of Anviz Global Inc. in the United States and other countries. It cannot be used without the permission of Anviz. Status LED -1- -2- -3- -4- Delete User (Delete user without administrator.) Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. Pressing key. 1 2 3 OK When the Nixie tube flashes, please press and key to select FP, AL or ID number and press . 4 1 2 3 4 5 6 Activation status. Activation status. Place same finger or swipe same card again. Delete user status / low battery voltage alarm. Place same finger or swipe same card again to delete. Unregistered finger or card . Need administrator verify. The Buzzer status Description Status Buzzer 1 2 3 4 5 The lock under initial states and be activated. Enable or Diable work mode. Finger or Card Verification failed. Operation succeedful. Delete all the user / low battery voltage alarm. Place finger in the center of the sensor. Place finger flat on the sensor surface. The Nixie tube will display normal user ID: 01. Please press and key to select and press to enter the registration status. (User ID range is 01-95) 4 OK OK Next ID number will be displayed after successful registration. Press to continue register user or press key to exit register status. 6 C * Note: One ID only can register one fingerprint or one card. Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. 1 2 5 3 Place one user finger twice on the fingerprint sensor or swipe card on the card area twice. Pressing key. OK OK C If "FP" selected, Press key need to place finger twice on the sensor or swipe card twice to delete. Press key to continue delete other users or press key to exit delete status. 5 OK If "AL" selected, Press key after six beeps form the lock all of the normal users will be delete. The lock will auto logout deletion status. OK C If "ID" selected, press to delete the appointed user. Press key to exit delete status or press and key to continue select ID number delete the appointed user. -5- -6- -7- -8- -9- Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. Hold key for 3 sec. Then it shows Ad. Please verify Admin FP or swipe Admin card to enter the registration status. It shows ID number, press or key to select ID then press to confirm. Place one user finger twice on the fingerprint sensor or swipe card on the card area twice (Please enable card function). Next ID number will be displayed after successful registration. Press to continue register user or Press key to exit registration status. 1 2 3 4 5 6 7 8 Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. Pressing key. Then it shows Ad Please verify Admin FP or swipe Admin card to enter the registration status. The Nixie tube will display normal user ID: 01. Please press and key to select and press to enter the registration status. (User ID range is 01-95) Place one user finger twice on the fingerprint sensor or swipe card on the card area twice. Next ID number will be displayed after successful registration. Press to continue register user or press key to exit exit register status. 1 2 3 4 5 6 7 8 OK OK C C - - - - - * Note: One ID only can register one fingerprint or one card. Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. 1 2 5 6 3 4 Place one Admin finger twice on the fingerprint sensor or swipe card on the card area twice. Next ID number will be displayed after successful registration. Press to continue register user or press key to exit register status. C When it shows admin ID: 96, press or to select ID then to confirm. (range : 96-99) OK Hold key for 3 sec. Register First Administrator (The first time uses lock to register administrator.) Register other Administrators Register Normal User Delete User Delete Administrators Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. Pressing key. Then it shows Ad Please verify Admin FP or swipe Admin card to enter the registration status. OK When the Nixie tube flashes, please press and key to select FP, AL or ID number and press . 1 2 3 4 5 6 Remove the battery box cover. Press any key to activate the lock. The Nixie tube shows --. Hold key for 3 sec. Then it shows Ad Please verify Admin FP or swipe Admin card to enter the registration status. When the Nixie tube flashes please. press and key to select FP. AL or ID number. Then press . 1 2 3 4 5 6 OK OK OK OK Normal Operation Mode 7 OK If "AL" selected, Press key after six beeps form the lock all of the administrators will be delete. The lock will auto logout deletion status. OK C If "ID" selected, press to delete the appointed administrator. Press key to exit delete status or press and key to continue select ID number delete the appointed administrator. OK OK C If "FP" selected, Press key need to place administrator finger twice on the sensor or swipe card twice to delete. Press key to continue delete other administrator or press key to exit delete status. 7 OK OK C If "FP" selected, Press key need to place finger twice on the sensor or swipe card twice to delete. Press key to continue delete other users or press key to exit delete status. OK If "AL" selected, Press key after six beeps form the lock all of the normal users will be delete. The lock will auto logout deletion status. OK C If "ID" selected, press to delete the appointed user. Press key to exit delete status or press and key to continue select ID number delete the appointed user.