Académique Documents
Professionnel Documents
Culture Documents
Harvesting System
Hamid Abdi
Center for Intelligent Systems Research
Deakin University
Waurn ponds 3216, Victoria, Australia
hamid.abdi@deakin.edu.au
Navid Mohajer
Center for Mechatronics and Automation
School of Mechanical Engineering, University of Tehran
Tehran, Iran
namohajer@yahoo.com
AbstractEnergy harvesting for wireless sensors and consumer
electronic devices can significantly improve reliability and
environmental sustainability of the devices by eliminating
dependency to rechargeable batteries and using clean and renewable
energy sources. Energy harvesting from different energy sources is
widely discussed among researchers and entrepreneurs including
harvesting energy in micro scale. This topic is receiving more
attention due to increasing number of low power consumer electronic
devices and wireless sensors and increasing demand for convenience
and availability of them. Among different sources, the energy
harvesting from humans passive motions is specifically useful for
consumer electronic devices such as mp3 players, Implantable
Medical Devices (IMD), and in future it can be used for other
devices. This paper presents a feasibility study for an energy
harvesting system from humans breathing. The system is based on a
modified pants belt integrated with a piezoelectric film and
harvesting circuit for generating electricity from reciprocal
abdominal motions of the user. The proposed system allows a safe
and convenient energy harvesting with no influence on the lungs
movements. The results of the simulation for this model are
presented.
Keywords Energy harvesting, Piezoelectric, Human passive
Motion, Energy Scavenging, Consumer electronic devices, Wireless
sensor, Implantable medical devices
I. INTRODUCTION
Green and renewable energy is of the interest of many
researchers, governments and public because of the upraising
environmental impacts of greenhouse gas emission and
increasing costs of the energy from fossil sources [1]. In
addition, the dependency to rechargeable batteries of portable
electronic devices and the requirement for regular access to
electric networks limits the performance of the devices [2].
Among the various subjects in the field of green and
renewable energy, the subject of energy harvesting for
wireless sensors and consumer electronic devices are widely
discussed by researchers to increase the users convenience
including reducing or eliminating the need for rechargeable
batteries and minimizing the necessity for regular access to the
electric network [3], [4], [5], [6].
Generally speaking, small size energy harvesters for such
devices can produce energy form (a) kinetic energy sources
such as wind, waves, or vibrating structures; (b)
electromagnetic energy sources such as wireless
communication spectrum; (c) solar energy; (d) thermal energy
sources such as humans body temperature and vehicles
motor heat; (e) energy from biological mechanisms such as
bio-fuels [7].
Although small electronic devices are mostly powered by
batteries, there are an increasing number of wireless sensors
using energy harvesters instead of the batteries [8], [1]. For
consumer electronic devices, there are different emerging
technologies that are under research or in commercialization
stages [2]. Solar powered mobile phone and Apples
yoyo
battery charger for iPhone
developed a kinetic
watch powered by human movement. It dispensed the
conventional batteries, being the human arm movement used
instead. The potential of this system to power larger devices is
limited by the slowness how people move.
In small scale power harvesters there are already several
types of these generators use mechanical vibrations or periodic
humans arms or knees motions for generating electricity.
According to [8], the American and British armies have tried
to power up sensors placed in soldiers boots. These devices
allow radiotelephone operation, which is often equipped with
heavy batteries. However, these energy harvesting devices
were not sufficiently robust to withstand extreme conditions
[15].
In the early 90s, freeplay
} [
] {
} (1)
In this matrix equation T, D, S and E are stress, electrical
displacement, strain and electrical field, respectively. In the
matrix of coefficients c, e and are Youngs Modulus (elastic
stiffness), piezoelectric stress constant and permittivity (ability
of electrical charge production), respectively.
The mechanical energy can be any kind of compression,
tension and bending forces [15], [21]. These transducers have
been used for many applications from industrial measurement
systems to research measurement as well as in generating
mechanical waves in ultrasonic transducers and medical
applications. A distributed pressure load applied on a
piezoelectric film causes an electrical charge displacement as
depicted in Figure 5.
Figure 4. Piezoelectric transducer used to harvest energy caused by a normal
distributed force
Various configurations of piezoelectric material can be
used for energy harvesting purpose. For instance piezoelectric
transducers have been recently used to design energy
harvesting shoes. They can scavenge some power from
walking energy and the dynamics of the force on the heel and
toes [22]. The average power produced by the shoe mounted
system was up to 8.4mW per foot strike and during the walk
which is an active process. Thus, besides being able to apply
this energy in MP3 players and mobile phones will be also
possible to use, not only for IMD, but also for any kind of
portable device. One of the most recent method use a pad of
piezoelectric or micro fluidic generator placed in humans
shoes. The pad is able to generate electricity during humans
walking and it was shown to be enough for recharging the
batteries for Mobile phones [23].
Figure 5. Mounting of piezoelectric material in an insole [22]
Another application that uses walk movement to generate
energy considers the mounting of the piezoelectric materials in
the floor. In this case, the floor beneath our feet acquires,
accumulates and converts the energy generated by the passage
of people into electricity, rather than applying it to the shoe
[4]. According to studies conducted by [5], each step produces
8W. This power is absorbed by the floor, being possible to
capture at least 30W of that energy. In this context, it is
possible to imagine a dance floor where the floor is designed
to reduce vibration and disperse energy, capturing it and
generating electricity, as it is equipped with energy scavengers
under the surface.
The other innovative idea for harvesting human passive
motion during walking was considered the backpack. Firstly
[24] regarded the vertical movement of backpack to produce
electrical energy. A mechanism was used in this work to allow
a load move vertically relative to frame fixed to the backpack.
In another work the authors considered the significant tension
force in the strap of a backpack [25]. They designed the
energy harvester by replacing the strap buckle with a
mechanically amplified piezoelectric stack actuator, as shown
in Figure 6.
Figure 6. Piezoelectric stack actuator replaced by strap buckle in a normal
wearable backpack [25]
C. Discussion
Among various methods, harvesting energy from the
passive body motions is particularly preferred because it is
more convenient than the active motions. The main problems
with the passive methods include (a) they can generate a small
amount of electricity and (b) the generator could be still
inconvenient. It is critical to optimally address these
constraints in body motion harvesting systems. This is
because, the more convenient the better chance for being used.
Among the different methods for generating electricity for
portable equipment from body passive motions piezoelectric
are common because of efficiency and frequency matching.
There have been some implementations of power generation
based on piezoelectric including electricity from talking,
walking and arm moving. However, they are still inconvenient
and require specific activities such as walking and placing or
removing them in the shoes. Besides, such method will not be
used by a lot of customers because of the possible foot smell
and/or short lifetime of such shoes.
III. ENERGY HARVESTER FROM BREATHING
This section proposes design of a pants belt with an integrated
energy harvesting capability.
A. Breathing and humans stomach pressure
During the respiration, when air moves in and out of our
lungs, the internal pressure of our body changes, accordingly
the size of stomach increased or decreased. When a pant belt
is worn, then it results in an increasing and decreasing
pressure on the belt too. A stomach pressure measured by a
medical breathing rate measurement belt is shown in Figure 7
that is for two cases of after mild exercise and during a rest
measurement [26]. For the case of after a mild exercise, the
pressure varies between 3.4kPa to 4.9kPa with the rate of
0.35Hz, and in the rest case, it varies between 3.2kPa to
4.2kPa with the rate of 0.25Hz. We have developed an image
processing code to separate the curves and digitize them.
These digitized pressure signals are used for simulation
purpose that is presented later in the paper. The comparison
between the pressure and the digitized data is shown in the
Appendix shown at the end of the paper.
Figure 7. Pressure waveforms on the abdomen relative to atmosphere
pressure after mild exercise and at rest [26]
This stomach pressure is applied directly to the belt and
by fabricating a piezoelectric film into the belt. It is possible to
transduce the variation of the pressure to electricity. The
electricity that is generated depends on the specifications of
the transducer, pressure magnitude, frequency, and stomach
shape change during respiration process.
B. Design of the harvester
To design the harvester, we need to determine the size of
piezoelectric film and the location to be mounted to achieve
high efficiency, comfortability and low cost. It is important to
not fabricate piezoelectric film into unstrained surfaces due to
the parasitic effects that declines the harvesters efficiency. To
select the size, we assume a normal pressure applied to the
front half of the belt. An ANSYS model shown in Figure 7 has
been developed to show distribution of strain. This model
shows that only the frontmost part of belt senses high amount
of strain which is selected to determine the size of
piezoelectric transducer. Table 1 shows technical
specifications of the selected transducer.
TABLE I. PIEZOELECTRIC TRANSDUCERS SPECIFICATIONS
Density 1.78 (g/cm
3
)
Relative Permittivity (
) 12
Piezo Strain Constant
d33 -3310
-12
(C/N) or (m/V)
d31 2310
-12
(C/N) or (m/V)
Piezo Stress Constant
e33 -33010
-3
(Vm/N)
e31 21610
-3
(Vm/N)
Electromechanical Coupling Factor (kt) 14 %
Capacitance in surface unit (Co) 380 (pF/cm
2
)
Young Modulus (c or E) 3.110
9
(N/m
2
)
Length (L) 171 (mm)
Width (W) 22 (mm)
Piezo Film Thickness (t) 52 (m)
Figure 8. Distribution of strain on front half of normal pants belt
The piezoelectric transducer is under various
compressions, extension or bending forces. For any case from
the specifications and size of the transducer, it is possible to
calculate the charge and voltage that will be produced. For our
case, a PVDF piezoelectric transducer is placed within a
Dacron-tape pants belt as shown in Figure 9. The piezoelectric
transducer is attached inside the belt and in the place of buckle
because of the higher strain region and the buckle is shifted
accordingly. PVDF piezoelectric is selected here due to its
flexibility in contrast in compare with fragile PZT.
Figure 9. Energy harvesting system from abdominal passive motion using
SOLIDWORKS
PVDF film is also suitable due to wide frequency range
(0.001-10
9
Hz) and dynamic range, low acoustic impedance,
low density and light weight. Among these, the acoustic
impedance is close to humane tissue impedance that results to
more efficient transducing. It is also worth mentioning that the
piezoelectric films properties change when excitation
frequency and temperature change, however these changes are
small for our case, therefore they are neglected.
Since the belt is under regular pressure increase and
decrease, a parallel compression force is applied to the
transducer, and the film is bent due to stomach surface
curvature. This implies the operating modes of 31 and 33 as
shown in Figure 10. However due to the fact that small area
results in a correspondingly higher stress for the same value of
pressure, the mode 31 produces higher charge and voltage
than mode 33.
Figure 10. Piezoelectric elements and operating modes
If a parallel or perpendicular force in mode 3n is applied to
the transducer, then the charge and open-circuit voltage are
obtained by:
(2)
(3)
In these equations
(4)
Where
(5)
Where
is relative permittivity,
is absolute permittivity
and the other parameters describe the size of piezoelectric film
introduced in Table 1. The relevant capacitances obtained
from both methods are nearly the same and it equals to 14.3nF
for our case. Due to the low frequencies of the abdominal
motions, the generated voltage is equivalent DC voltage
generator. A simple model of the harvesting system is shown
in Figure 12.
Figure 12. Scheme of Piezoelectric film inclined by stomach shape form and
the equivalent RC Circuit
By this model, the harvester acts as a high pass filter and
as a result of that there will be a cut-off frequency given by:
(6)
By assuming R
L
to be large enough, the open-circuit
voltage will be close to the load voltage. However taking into
consideration the low frequency of abdominal motion, the
open-circuit voltage is:
(7)
Broadly speaking, by measuring the voltage on the load
and figuring the
).
TABLE II. AVERAGE VALUES FOR USING RESISTIVE LOAD
Applied
Pressure
VL (V) Vo (V) PL (uW) Po (uW)
Power
Efficiency
At Rest
( )
2.2 6.3 5.1 28.3 18%
After Mild
Exercise
( )
4.3 10.8 18.5 83.4 23%
From this table it can be seen that by increasing operating
frequency towards resonance frequency that is normally large
, the harvested power and power efficiency will be increased.
In the next step an interface circuit is used to convert the semi-
AC current of the transducer to a DC signal. In this work a
self-powered interface circuit is used as shown in Figure 13.
The proposed Proteus circuit is compact with low energy
dissipation and produces a 3.3VDC.
Figure 13. Compact and self-powered interface circuit to provide 3.3 VDC
The LTC3588-1 used here is an ultralow quiescent current
power supply that integrates a low-loss full-wave bridge
rectifier with a high efficiency buck converter [27].
IV. MODELING AND SIMULATION
In this section a detailed mathematical and simulation model
of the belt harvester is introduced. As was mentioned earlier,
the piezoelectric film is under bending and compression forces
and mode 31 dominates the mode 33. Detailed modeling will
help to validate this fact as well.
For the piezoelectric film shaped in the belt of Figure 13,
the abdominal pressure produced the strain in 1-direction of:
(8)
Where is the angle of film deflection caused by stomachs
curvature and length of the film, P is the pressure magnitude
and the other parameters were explained in Table 1. We
obtained the value of
(9)
The parameters in this equation were introduced in section
2. After integration over the thickness and with the assumption
that D
3
(I), E
3
(V), and S all are set in the same frequency rate
( ), the voltage is obtained by:
(8)
And so the average value of power will be obtained by:
||
(9)
Figure 14 shows the variation of average power versus
different resistive loads for two cases of at rest and after mild
exercise.
Figure 14. Average of extracted power for different resistive loads in two
cases of at rest and after mild exercise
From this figure, with the optimum resistive loads the
maximum power that could be extracted are 1.2 and 2.3mW
for the rest and after mild exercise, respectively. Accordingly,
the magnitude of voltage depends on resistance value as stated
by (8). For instance the average voltages for a 1 resistive
load are 7.4V and 11.7V for the rest and after mild exercise,
respectively.
The method used to obtain the voltages and powers does
not consider the power loss in the elements that exists in
practice and therefore a difference is observed between
theoretical and practical solution. On the other hand due to
high impedance of piezoelectric element, the produced voltage
tends to be orders of magnitude more than the induced current
as predicted before. Under this circumstance use of the
conditioning circuit is essential for optimal power
transmission.
This model has been simulated in Matlab Simulink in
order to analyze the operation detail of the system and for
future improving of the design performed in this paper. The
simulation model consists of three stages of humans
abdominal motions model, the belt and piezoelectricity effect
model and the interface circuit as shown in Figure 15.
Figure 15. Simulink model of proposed energy harvesting system
Humans Abdominal Motions Model: This part of the model
shown by blue region in Figure 15 uses a digitized table of
pressure values corresponding to the pressure curve of Figure
7. The digitization method was explained earlier and the
matching of it with the actual pressures is shown in the
Appendix. These pressure data are the P1 and P2 bus line of
Simulink model and the simulation of the them are shown in
Figure 16-first scope.
0 50 100 150
0
0.5
1
1.5
2
2.5
Resistive Load (MOhms)
E
x
t
r
a
c
t
e
d
P
o
w
e
r
(
m
W
)
At Rest
After Mild Exercise
Figure 16. Pressure, voltage and power curves from the first and second parts
of simulation model-for the rest (lower) and after mild exercise (upper)
and 1 resistive load
Belt and Piezoelectric Effect Model: The model of the belt and
the piezoelectric film is based on the equations 6-9. The
voltage and power of this model with the actual pressure data
of Figure 7 are shown in Figure 16 in the second and third
scope.
Harvester Circuit: The Simulink model of the harvester circuit
was displayed in Figure 15 which is the green block. Using the
simulation model of this section we have observed that a
3.3VDC was provided by this harvester circuit after a very
short fluctuation and the average of power is specified by the
value of resistive load that is 1 in the Simulink model.
V. CONCLUSION
This paper discussed existing methods of energy
harvesting from humans body motion and introduced a novel
system for harvesting energy from abdominal motion. The
presented method allowed the harvesting to occur from
completely passive motion with an special focus on the user-
friendliness of the harvester.
The harvester was designed by integrating a PVDF
piezoelectric transduced with a normal pants belt after
calculating the maximum strain region of the belt. The system
including piezoelectric transducer was modeled by Matlab and
the results showed that it can provide up to 1.2mW in rest time
and 2.3mW after mild exercise time. This amount of energy is
sufficient to power an mp3 player or IMD.
Acknowledgement: This research is fully funded by the
Centre for intelligent systems research as the IP holder.
Appendix: The below figure shows the digitized pressure
curves for the rest and mild exercise using an image
processing method. In the image processing method, we
selected a curve and filtered in, then read the pixel and scaled
it to the range of the time and pressure as shown in Figure 17.
Figure 17. Digitized pressures (left side images) using the image processing method and matching of it with the image data (right side figures)
REFERENCES
[1] G. S. Tewolde, "Current trends in low-power embedded
computing," in Electro/Information Technology (EIT),
2010 IEEE International Conference on, 2010, pp. 1-6.
[2] S. Chalasani and J. M. Conrad, "A survey of energy
harvesting sources for embedded systems," in
Southeastcon, 2008. IEEE, 2008, pp. 442-447.
[3] A. Khaligh, Z. Peng, W. Xiaochun, and X. Yang, "A
hybrid energy scavenging topology for human-powered
mobile electronics," in Industrial Electronics, 2008.
IECON 2008. 34th Annual Conference of IEEE, 2008,
pp. 448-453.
[4] A. Khaligh, Z. Peng, and Z. Cong, "Kinetic Energy
Harvesting Using Piezoelectric and Electromagnetic
Technologies-State of the Art," Industrial Electronics,
IEEE Transactions on, vol. 57, pp. 850-860, 2010.
[5] J. J. H. Paulides, J. W. Jansen, L. Encica, E. A.
Lomonova, and M. Smit, "Human-powered small-scale
generation system for a sustainable dance club," in
Electric Machines and Drives Conference, 2009. IEMDC
'09. IEEE International, 2009, pp. 439-444.
[6] R. Want, K. I. Farkas, and C. Narayanaswami, "Guest
Editors' Introduction: Energy Harvesting and
Conservation," Pervasive Computing, IEEE, vol. 4, pp.
14-17, 2005.
[7] J. Paulo and P. D. Gaspar, "Review and Future Trend of
Energy Harvesting Methods for Portable Medical
Devices," in World Congress on Engineering,
Proceedings of the London, U.K., 2010, pp. 1-6.
[8] J. A. Paradiso and T. Starner, "Energy scavenging for
mobile and wireless electronics," Pervasive Computing,
IEEE, vol. 4, pp. 18-27, 2005.
[9] P. Spies, M. Pollak, and G. Rohmer, "Energy harvesting
for mobile communication devices," in
Telecommunications Energy Conference, 2007.
INTELEC 2007. 29th International, 2007, pp. 481-488.
[10] Y. Jaeseok, S. N. Patel, M. S. Reynolds, and G. D.
Abowd, "Design and Performance of an Optimal Inertial
Power Harvester for Human-Powered Devices," Mobile
Computing, IEEE Transactions on, vol. 10, pp. 669-683,
2011.
[11] N. Ben Amor, O. Kanoun, A. Lay-Ekuakille, G.
Specchia, G. Vendramin, and A. Trotta, "Energy
harvesting from human body for biomedical autonomous
systems," in Sensors, 2008 IEEE, 2008, pp. 678-680.
[12] J.-A. Heslin and K. J. Nolan, The Calorie Counter, 5 ed.,
2010.
[13] F. Maier, M. Sturmlechner, and S. Dierneder, "Novel
energy harvester with low friction losses," in Systems,
Signals and Devices, 2009. SSD '09. 6th International
Multi-Conference on, 2009, pp. 1-6.
[14] Q. Li, V. Naing, and J. M. Donelan, "Development of a
biomechanical energy harvester," Journal of
NeuroEngineering and Rehabilitation, vol. 6:22, 2009.
[15] M. N. Fakhzan and A. G. A. Muthalif, "Vibration based
energy harvesting using piezoelectric material," in
Mechatronics (ICOM), 2011 4th International
Conference On, 2011, pp. 1-7.
[16] C. A. Howells, "Piezoelectric energy harvesting," Energy
Conversion and Management, vol. 50, pp. 1847-1850, 7//
2009.
[17] R. D. Kornbluh, R. Pelrine, Q. Pei, R. Heydt, S.
Stanford, S. Oh, et al., "Electroelastomers: applications
of dielectric elastomer transducers for actuation,
generation, and smart structures," pp. 254-270, 2002.
[18] J. Y. Hayashida, "Unobtrusive Integration of Magnetic
Generator Systems into Common Footwear," Bachelor of
Science, Department of Mechanical Engineering,
MASSACHUSETTS INSTITUTE OF TECHNOLOGY,
2000.
[19] J. Kymissis, C. Kendall, J. Paradiso, and N. Gershenfeld,
"Parasitic power harvesting in shoes," in Wearable
Computers, 1998. Digest of Papers. Second International
Symposium on, 1998, pp. 132-139.
[20] L. Wang and F. G. Yuan, "Vibration energy harvesting
by magnetostrictive material," Smart Mater. Struct. 17
045009, vol. 17, p. 14, 2008.
[21] S. Sherrit, "The physical acoustics of energy harvesting,"
in Ultrasonics Symposium, 2008. IUS 2008. IEEE, 2008,
pp. 1046-1055.
[22] N. S. Shenck and J. A. Paradiso, "Energy scavenging
with shoe-mounted piezoelectrics," Micro, IEEE, vol. 21,
pp. 30-42, 2001.
[23] (2012). Shoe Power Generation. Available:
http://www.kaajakari.net/
[24] L. C. Rome, L. Flynn, E. M. Goldman, and T. D. Yoo,
"Generating Electricity While Walking with Loads,"
Science, vol. 309, pp. 1725-1728, September 9, 2005
2005.
[25] J. Feenstra, J. Granstrom, and H. Sodano, "Energy
harvesting through a backpack employing a
mechanically amplified piezoelectric stack," Mechanical
Systems and Signal Processing, vol. 22, pp. 721-734, 4//
2008.
[26] "Sensor Accessories-Breathing Rate Belt ", D. H. G.
Ltd., Ed., ed, 2010.
[27] "Piezoelectric Energy Harvesting Power Supply," L. T.
Corporation, Ed., ed, 2010.