EDFA EV Board Computer cabe !S"#" moded DB$ e%tention cabe &'V( &#.#V )o*er Supp+ EDFA Input EDFA ,utput -ote: ma.e sure t/e testing station are ESD protected( connect t/e cabe as t/e diagram be0ore turn on po*er supp+. EVBoard Connecter: !S"#" Connector "1)in Connector 2pin Connector #1 pin connector &'V &#.#V 3-D 1#"# 3reat 4a Dr.( 4ipitas( CA $'1#' Engineering Version 1.1 Te:5167'1#76666( Fa%: 5167'1#76$66 1 #. So0t*are Insta and Setup: Software Install: 8og on t/e computer as administrator !un 9in:ip program to e%tract dis.1.:ip to +our destination director+ E%ecute t/e setup.bat 0ie in t/e director+ T/en run t/e !S"#"EV.e%e program. -ote: T/e setup.bat incude t*o command ine( 0irst insta t/e VB!un21.e%e( t/en run regsvr#" mscomm#".oc% to register mscomm#".oc% active% contro. I0 t/e regsvr#" doesn;t run during setup( insure t/e s+stem pat/ incudes t/e pat/ t/at regsvr#" ocated or +ou can edit t/e setup.bat 0ie to incude t/e pat/ be0ore t/e command regsvr#". I0 +ou using t/is program in ot/er anguage version microso0t operating s+stem( +ou can use contro pane7regiona setting to set t/e *indo*s environment to Engis/ environment under 9indo*"111 or 9indo*s<). RS232 interface setting: In t/e !S"#"EV program +ou can Con0igure !S"#" inter0ace using t/e Con0igure !s"#" button )ort: seect seria port( de0aut vaue is seria port 1. Setting: de0aut vaue is: $211( n( 6(1 $211: setting baud rate( n: no parit+ c/ec.( 6: data bits 1: stop bit 5. Command Instruction: Command list and instruction: In t/e program +ou can use t/ese command to communicate *it/ EDFA. Running Mode Command: =ou can use C4D_Set!unning4ode and C4D_!ead!unning4ode to set or read t/e EDFA current running mode.
CMD_ReadRunningMode !ead EDFA running mode( !unning mode 1: A)C !unning mode 1: constant pump drive current mode CMD_SetRunningMode Set running mode. !unning mode 1: A)C( !unning mode 1: constant pump drive current Setting parameter Command: >sing t/e setting parameter command to set t/e parameter o0 t/e EDFA( suc/ as pump drive current( output po*er. 1#"# 3reat 4a Dr.( 4ipitas( CA $'1#' Engineering Version 1.1 Te:5167'1#76666( Fa%: 5167'1#76$66 " CMD_SetargetIp Set target pump drive current( unit is 1.1mA( t/e imit is 0rom 1 to #111? 1 to #11mA@ CMD_Setarget!out Set target output po*er( unit is 1.11dBm( t/e imit is 0rom A"111 to 1"11?7"1 to 1"dBm@ Reading parameter command: >sing t/ese command to read parameters 0rom t/e EDFA. CMD_ReadIp !ead pump drive current( resut unit is 1.1 mA CMD_Read!out !ead output po*er( unit is 1.11dB CMD_Read"dBac#!ower !ead )ump rear monitored po*er( unit is m9? 0or re0erence on+. CMD_Read$larm%ord !ead Aarm *ord( see aarm *or. de0ine tabe. CMD_ReadempIn&'() !ead temperature in modue( unit is BC ED*$ control command: >sing t/ese command to contro EDFA s/ut do*n( turn on and reset t/e program. CMD_S+utDown S/ut do*n EDFA CMD_urn,n Turn on EDFA CMD_SoftReset !eset EDFA $larm %ord Define a-le: Bit 1 I)_,VE! )ump drive current over imit Bit 1 ,>T)>T_8,9 ,utput po*er is ess t/an setting output po*er ?C1dB@ Bit " ,>T)>T_,VE! ,utput po*er is over t/an setting output po*er ?D1dB@ Bit # 8D_A84 8D po*er is ess t/an 'm9 o0 setting pump po*er Bit 5 TE4)_,VE! Temperature o0 t/e modue is over 2' BC '. E%ampe a. A)C mode e%ampe: >sing t/e C4D_Set!unning4ode to set EDFA to A)C mode ?mode 1@( ne%t >sing C4D_SetTarget)ump)o*er to set target output po*er( 0or e%ampe( set target output po*er to 1111?11dBm@( t/en can read output po*er b+ t/e command C4D_!ead)out. b. Constant pump drive current mode e%ampe >sing t/e C4D_Set!unning4ode to set EDFA to constant pump drive current ?mode 1@( ne%t using command C4D_SetTargetI) to set target drive current. For e%ampe setting target drive current to "111?"11mA@. 1#"# 3reat 4a Dr.( 4ipitas( CA $'1#' Engineering Version 1.1 Te:5167'1#76666( Fa%: 5167'1#76$66 #