Académique Documents
Professionnel Documents
Culture Documents
Command: rectangle
Chamfer/Elevation/Fillet/Thickness/Width/<First corner>: 1,1
Other corner: 37.44,19.94
Command: linetype
Command: osnap
Command: bhatch
Select objects: 1 found
Command: mirror
Select objects: Other corner: 2 found
Select objects:
First point of mirror line:
Second point: 1,1
Delete old objects? <N>
Command: explode
Select objects: 1 found
Select objects:
Hatch boundary associativity removed.
Command: offset
Offset distance or Through <Through>: 3.22
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <Through>: 18.22
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <18.2200>: 0.97
Select object to offset:
Side to offset?
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 8 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: offset
Offset distance or Through <Through>: 2.5
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <2.0000>: 1.6
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 7 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: offset
Offset distance or Through <1.1000>: .05
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <0.0500>: 3
Select object to offset:
Side to offset?
Select object to offset:
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 8 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: line
From point:
To point: @.5,0
Command: circle
3P/2P/TTR/<Center point>: 8.42,10.47
Diameter/<Radius>: .2
Command: offset
Offset distance or Through <3.0000>: 2.22
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <2.2200>: 7.97
Select object to offset:
Side to offset?
Command: break
Select object:
Enter second point (or F for first point): F
Enter first point:
Enter second point:
Command: offset
Offset distance or Through <7.9700>: 3.8
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <3.8000>: 1
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 16 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: fillet
(TRIM mode) Current fillet radius = 1.2222
Polyline/Radius/Trim/<Select first object>: R
Enter fillet radius <1.2222>: 2
Command: fillet
(TRIM mode) Current fillet radius = 2.0000
Polyline/Radius/Trim/<Select first object>:
Select second object:
Command: fillet
(TRIM mode) Current fillet radius = 2.0000
Polyline/Radius/Trim/<Select first object>:
Select second object:
Command: offset
Offset distance or Through <1.0000>: 12.62
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <12.6200>: .45
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <0.4500>: 2.22
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 34 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: fillet
(TRIM mode) Current fillet radius = 3.0000
Polyline/Radius/Trim/<Select first object>: R
Enter fillet radius <3.0000>: 6
Command: fillet
(TRIM mode) Current fillet radius = 6.0000
Polyline/Radius/Trim/<Select first object>:
Select second object:
Command: fillet
(TRIM mode) Current fillet radius = 6.0000
Polyline/Radius/Trim/<Select first object>:
Select second object:
Command: offset
Offset distance or Through <2.2200>: 3.8
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <3.8000>: 3.1
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 36 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: break
Select object:
Enter second point (or F for first point): f
Enter first point:
Enter second point:
Command: offset
Offset distance or Through <0.5000>: 6.3
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 28 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: osnap
Command: circle
3P/2P/TTR/<Center point>:
Diameter/<Radius> <0.2000>: 1.9
Command: osnap
Command: line
From point:
To point:
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 28 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: mirror
Select objects: Other corner: 43 found
Select objects:
First point of mirror line:
Second point:
Delete old objects? <N>
Command: circle
3P/2P/TTR/<Center point>: 19.22,10.47
Diameter/<Radius> <1.9000>: 1.9
Command: offset
Offset distance or Through <4.9000>: .1
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <0.1000>: .05
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <0.0500>: .85
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <0.8500>: .5
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 97 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: offset
Offset distance or Through <0.5000>: .75
Select object to offset:
Side to offset?
Command: offset
Offset distance or Through <0.7500>: 1
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 84 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: offset
Offset distance or Through <4.4500>: .3
Select object to offset:
Side to offset?
Command: trim
Select cutting edges: (Projmode = UCS, Edgemode = No extend)
Select objects: Other corner: 73 found
Select objects:
<Select object to trim>/Project/Edge/Undo:
Command: line
From point:
To point: @-.4,0
Command: line
From point:
To point: @.4,0
Command: osnap
Command: bhatch
Select objects: 9 found
Select objects:
Command: mirror
Select objects: 5 found
Select objects:
First point of mirror line: Second point:
Delete old objects? <N> Y
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 36.4400
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 18.9400
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 26.0000
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 14.0000
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 30.0000
Command: dimradius
Select arc or circle:
Dimension text = 1.9000
Dimension line location (Mtext/Text/Angle):
Command: dimradius
Select arc or circle:
Dimension text = 3.0000
Dimension line location (Mtext/Text/Angle):
Command: dimradius
Select arc or circle:
Dimension text = 6.0000
Dimension line location (Mtext/Text/Angle):
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 3.0000
Command: dimlinear
First extension line origin or press ENTER to select:
Second extension line origin:
Dimension line location (Mtext/Text/Angle/Horizontal/Vertical/Rotated):
Dimension text = 1.0000
Command: mtext
Current text style: STANDARD. Text height: 0.4889
Specify first corner:
Specify opposite corner or [Height/Justify/Rotation/Style/Width]:
Command: '_zoom
All/Center/Dynamic/Extents/Previous/Scale(X/XP)/Window/<Realtime>:
Press Esc or Enter to exit, or right-click to activate pop-up menu.
Command: bmpout
Select objects: Other corner: 120 found