Vous êtes sur la page 1sur 8

HERCULES

15




EQUIPMENT INVENTORY
Page 1 Updated 9/01/04
Hercules Drilling Company Rig 15

TYPE: - Baker Marine Big Foot III Shallow water draft. Independent leg jackup
with four (4) cylindrical legs outfitted for 20,000 ft. drilling in a maximum
of 85 ft. of water. Approved by the American Bureau of Shipping as an
(Maltese Cross) A-1 Mobile Offshore Drilling Unit. Built under the United
States Coast Guard rules for Mobile Offshore Drilling Units

BUILDER: - Baker Marine Corporation

ELEVATING SYSTEM: - Baker Marine Sixteen (16) pinions, four (4) per leg, electro hydraulic rack
and pinion. Continuously engaged for elevating speeds to one (1) foot
per minute at full variable load.

PRINCIPAL CHARACTERISTICS:
LENGTH OVERALL 155'-9"
BREADTH OVERALL 110'-0"
DEPTH HULL 15'-0"
SLOT 35' X 35'
LENGTH OF LEGS (MEASURED TO TIP OF SPUD CAN) 173'-0"
LEG DIAMETER 8'-0"
SPUD CAN DESCRIPTION:
LENGTH OVERALL 30' -0"
BREADTH OVERALL 30' -0"
DEPTH 5' -0"
CENTER TO CENTER OF AFT & BOW LEGS 121' -0"
CENTER TO CENTER OF PORT TO STARBOARD 80' -0"

DESIGN OPERATING CONDITIONS:
NON-HURRICANE OPERATING
HURRICANE PLUS DRILLING LOADS

CONDITION A CONDITION B CONDITION C
MAXIMUM VARIABLE LOAD (KIPS) 3,000 3,000 3,000
STILL WATER DEPTH (FT.) 85' 85' 85'
MAX. WAVE HEIGHT (FT.) 38 20' 30'
CORRESPONDING WAVE PERIOD 14 sec. 8 sec. 10 sec.
MAX. WIND VELOCITY 100 kn. 100 kn. 100 kn.
ONE MINUTE AVERAGE) AIR GAP (FT.) 40' 40' 40'
LEG CAN PENETRATION (FT.) 15' 15' 15'

OPERATING WATER DEPTH 9' to 85'
VARIABLE LOADS: (EXCLUSIVE OF HOOK, ROTARY &
SETBACK LOADS):

NORMAL DRILLING 2,000 kips plus 1000 kips hook load
MOVING WITH SPUD CANS:
BUOYANT 2,200 kips
J ACKING 3,000 kips

MAXIMUM ALLOWABLE DRILL FLOOR LOADING: 1,300 kips
HOOK LOAD 1,000 kips
ROTARY LOAD 750 kips (including impact)
SETBACK 500 kips

Note: (A) Above listed loads also include riser tension load, if applicable
EQUIPMENT INVENTORY
Page 2 Updated 9/01/04
Hercules Drilling Company Rig 15


Drill Floor Loading
(Well Ctr. in Ft.) Aft of Stern

Well on Centerline

Well 6' of Centerline Port or Starboard
0 - 7'6" 1,300K 800K
12'-6" 1,000K 800K
17'-6" 1,000K 800K

QUARTERS:
ACCOMMODATIONS 58 men
TREATMENT ROOM 2 each
GALLEY & MESS ROOM 2 each
ONE RECREATION ROOM 1 each
OFFICES 2 each
CONTROL ROOM 1 each
RADIO ROOM 1 each

HELIPORT:
WIDTH 55' -0"
LENGTH 55' -0"
HELICOPTER CRITERIA: 11,500 lb. G.M.C. Rated for Bell 212 or Dauphin 365

EXPENDABLE CAPACITIES:
DIESEL FUEL 1,924 bbls
DRILL WATER 5,668 bbls
POTABLE WATER 1,118 bbls
LUBE OIL 10 bbls
BULK MUD & CEMENT (6 TANKS) 6,600 cu. ft.
SACK STORES 3,000 sacks
ACTIVE & RESERVE MUD PITS (4 TANKS) 1,360 bbls
SLUGGING PIT 115 bbls
SAND TRAP & SOLIDS CONTROL PITS (3 TANKS) 152 bbls

CONTRACTOR FURNISHED STANDARD EQUIPMENT
DRILLING EQUIPMENT:
DERRICK: - Dreco API Standard 4E 147' X 30' X 30' derrick with 14'
square top and racking capacity of 270 stds. of 5" drill pipe

CROWN BLOCK: - Dreco 760 ton with eight (8) 60" O.D. sheaves grooved for
1 3/8" wire rope complete with safety platform

STABBING BOARD: - Air operated 30' adjustable stabbing board

WIRELINE ANCHOR: - Superior F10 with M.D. cell

DRAWWORKS: - Dreco Model D-2000E with double drum complete with
catheads driven by two each EMD Model D79 traction
motors, air cooled by blowers driven by 7.5 HP motors

BRAKE: - ELMAGO 7838

DRILL LINE: - 1-3/8" diameter 6 X 19 EIPS drill line

ROTARY: - Gardner Denver Model RT 3750 independently driven by
an EMD Model D79 D.C. electric traction motor through
two speed transmissions 2010 Oilwell Transmission

SWIVEL: - National P-500, 500 ton
EQUIPMENT INVENTORY
Page 3 Updated 9/01/04
Hercules Drilling Company Rig 15


HOOK/BLOCK: - National 660-G. 550 ton. Traveling block with six (6) 60"
sheaves. Baash Ross/J oy 500 ton Return-A-Matic hook

WIRELINE UNIT: - One (1) .092 wireline measuring unit powered by a 25 HP
electric motor

DRILLERS CONSOLE: - Martin Decker Model AWB9-5; (1) One Martin Decker EB
weight indicator, (2) Two Martin Decker 0-5000 PSI mud
gauges.

KELLY: - One (1) Omsco 5-1/4" Hex X 40' long X 3" I.D.IF

KELLY BUSHING: - Varco

KELLY SPINNER: - Varco series 6600

SAFETY VALVES: - One (1) Omsco 10,000 psi upper "kelly cock", 6 5/8"
regular. One (1) 6 1/2" 10,000 psi Hydril lower safety
valve, 5 X IF connection. One (1) Hydril inside BOP

BRAKE COOLING UNIT: - One (1) 1,260 gallon brake cooling tank with heat
exchanger and two (2) 2 X 3 centrifugal pumps driven by
25 HP motors.

WELL CONTROL EQUIPMENT:
RAM PREVENTERS: - One (1) Cameron Type "U" 13-5/8" double ram type
preventers. 10,000 psi W.P. with flanged top and bottom,
four (4) 4-1/16" (10,000#) flanged side outlets
- One (1) Cameron Type "U" 13-5/8" single ram type
preventer. 10,000 psi W.P. with flanged top and bottom,
four (4) 4-1/16" (10,000#) flanged side outlets.

ANNULAR PREVENTERS: - One (1) Shaffer 13-5/8" annular 5,000 psi W.P. with a
5,000 psi W.P. studded top and 10,000 psi W.P. flanged
bottom. H2S trim

VALVES: - One (2) hydraulically operated gate valves, 4 1/16" ,
10,000 psi W.P. with flanged ends. One more of same
"manually operated"
- Two (2) 2-2/16", (15,000#) manually operated gate valves,
10,000 psi W.P. with flanged ends.

CHOKE MANIFOLD: - Shaffer 3-1/8", 10,000 psi W.P. with two (2) Shaffer 3",
10,000-psi W.P. hand adjustable chokes, one (1) 4" full
flow line. (Super Choke Rental by Operator). H2S trim

STANDPIPE MANIFOLD: One (1) Demco 5" 5,000 psi dual standpipe manifold

BOP CONTROL UNIT: Koomey Type 80 with 18 each 11-gallon bottles, 340-gallon
reservoir. One (1) triplex pump and three (2) air pumps.
Complete with remote control panels

MUD/GAS SEPARATOR: One (1) 48" I.D. X 14' long vertical mud/gas separator
complete with two (2) top-side 4" inlets for lines from
choke/kill manifold, one (1) 6" top exit to flare line, one (1)
8" bottom discharge
EQUIPMENT INVENTORY
Page 4 Updated 9/01/04
Hercules Drilling Company Rig 15


MUD SYSTEM:
MUD PUMPS: - Two (2) Gardner Denver Model PZ11, 7" X 11" triplex
pumps. Each driven by two (2) D-79 EMD motors. Pumps
fitted with pulsation dampeners and safety valves

AUXILIARY PUMPS: - Two (2) 6" X 8" centrifugal pumps driven by 100 HP
electric motors for super charging
- Two (2) 6" X 8" centrifugal pumps driven by 100 HP
electric motors for mixing and backup degassing
- Two (2) Mission Magnum 6" X 8" centrifugal pumps
driven by 100 HP electric motors
- One (1) - Desilting/Mud Cleaning
- One (1) - Desander

SHALE SHAKER: Two (2) Fluid System linear motion shale shakers

DESILTER: One (1) Brandt Quadraflow Fluid Conditioner

DEGASSER: One (1) Swaco degasser

TRIP TANK: One (1) 40 barrel trip tank system

MUD AGITATORS: - Eight (8) 10 HP Radicon Model AB200 Mud Agitators for
active and reserve system
- One (1) HP Brandt Mud Agitator for chemical mixing and
slugging tank

MUD HOPPERS: Two (2) Demco Model 612-B mud hoppers

BULK SYSTEM:
BULK TANKS: - Four (4) 1,100 cu. ft. and two (2) 850 cu. ft. tanks for
Barite and Cement complete with all piping and fittings

BARITE SURGE TANK: - One (1) 70 cu. ft. diameter by 6'4" high

CEMENTING UNIT: - Operators preference BJ . ON BOARD

RIG EQUIPMENT:
PRIME MOVER: - Three (3) EMD Model 12-645E9B engines directly
connected to Three (3) Model AB20-G generators each
rated at 2625 KVA, 600 volts, 60 Hz at 900 RPM
- Three (3) remote mounted radiators for main engines.
Driven by 50 HP electric motors

SCR SYSTEM: - IPS, Four (4) bay with Westinghouse breakers

AIR COMPRESSORS: - One (1) Ingersoll-Rand Model 40-B high pressure air
compressors. Powered by 30 HP electric motors
- One (1) Helical Screw, model 100H-SP-05 high pressure
air compressor powered by 125 HP electric motor
- One (1) Helical Screw, model 75H-SP-05 low pressure air
compressor powered by 100 HP electric motor
- One (1) Airdyne refrigerated compressed air dryer model
8070 for high pressure and low pressure air systems
- One (1) Airdyne refrigerated model 80500 air dryer
- Two (2) 53 cu. ft. air receiver

EQUIPMENT INVENTORY
Page 5 Updated 9/01/04
Hercules Drilling Company Rig 15

SEWAGE TREATMENT: - One (1) Red Fox USCG Type II Marine Sanitation unit
model 12M812-27

CRANES: - Two (2) Baker Marine Corp., Model 900 cranes. Each
powered by Detroit Diesel Model 671 diesel engine.
Cranes fitted with 100' booms and Martin Decker load
cells

SKIDDING SYSTEM: - Independent hydraulic power package powered by 60 HP
electric motor complete with controls. Hydraulic jacks skid
substructure and drill floor

WELDING MACHINES: - Two (2) Miller 400 AMP

RAW WATER PUMPS: - One (1) submersible pump

FUEL CENTRIFUGE: - One (1) Alfa-Laval type MAB-103B-24-60 , 42054-1 fuel
oil centrifuge

AIR WINCHES: - Two (2) Ingersoll-Rand K5UL rated at 2000 #line pull with
drum capacity of 5/8" wire rope on drill floor
- One (1) Ingersoll-Rand EUAB/PT derrick winch

SERVICE PUMPS: - Two (2) 3 X 4 centrifugal pups driven by 25 HP 1800 RPM
electric motors for drill water service
- Two (2) 3 X 4 centrifugal pumps driven by 60 HP, 3450
RPM electric motors for fire water service
- Two (2) 3 wildon m8 diaphragm pumps for bilge and
ballast service
- Two (2) centrifugal pumps driven by 7.5 HP, 3600 RPM
motors for potable water service

COMMUNICATIONS:
MARINE VHF: -Two (2) Sailor type RT144AC

GAI-TRONICS SYSTEM: - One (1) Gai-tronics sound powered inter-communication
telephone system with 18 stations circuits and public
address throughout rig

LIFESAVING EQUIPMENT:
LIFEBOATS: - Two (2) Watercraft boats, 58 persons each, complete with
gravity launch gear

GENERAL ALARM SYSTEM: - As required by U.S.C.G

LIFE RINGS/LIFE JACKETS: - As required by U.S.C.G.

WELL LOGGING UNIT: - Operator's Preference

DRILL PIPE: - 12,000 Ft. 5 19.50 ppft tube 4 IF thread

HANDLING EQUIPMENT: - For 5 Drill Pipe.

DRILL COLLARS: - 9- 6 DC 91 lb p ft. XH thread
- 6- 8 DC 150 lb p ft. 6 5/8 regular

Vous aimerez peut-être aussi