0 évaluation0% ont trouvé ce document utile (0 vote)
214 vues3 pages
IADC DULL BIT GRADING @ inner CU I NG structure (AII inner MS.) in columns 1 and 2 a linear scale from 0 t o 8 Is used to inner 0 describe the condklon of the cutting structure according to the followlng: STEEL TOOTH BlTS A measure of lost tooth height due to abrasion andlor damage. 8 - TOTAL LOSS OF TOOTH HEIGHT
IADC DULL BIT GRADING @ inner CU I NG structure (AII inner MS.) in columns 1 and 2 a linear scale from 0 t o 8 Is used to inner 0 describe the condklon of the cutting structure according to the followlng: STEEL TOOTH BlTS A measure of lost tooth height due to abrasion andlor damage. 8 - TOTAL LOSS OF TOOTH HEIGHT
IADC DULL BIT GRADING @ inner CU I NG structure (AII inner MS.) in columns 1 and 2 a linear scale from 0 t o 8 Is used to inner 0 describe the condklon of the cutting structure according to the followlng: STEEL TOOTH BlTS A measure of lost tooth height due to abrasion andlor damage. 8 - TOTAL LOSS OF TOOTH HEIGHT
(AII inner MS.) BEARINGS1 GAGE OTHER REASON SEALS DULL @ OUTER CUTTING STRUCTURE (Gage row only.) In columns 1 and 2 a linear scale from 0 t o 8 Is used to INNER 0 describe the condklon of the cuttlng structure according to the followlng: STEEL TOOTH BlTS A measure of lost tooth height due to abrasion andlor damage. 0 - NO LOSS OF TOOTH HEIGHT. 8 - TOTAL LOSS OF TOOTH HEIGHT. CHAR. PULLED -0 0 0 0 @ INSERT BlTS A measure of total cutting structure reduction due to lost, worn andlor broken inserts. 0 - NO LOST, WORN AND/OR BROKEN INSERTS. 8 - ALL INSERTS LOST, WORN ANWOR BROKEN. FIXED CUlTER BlTS A measure of lost, worn and/or broken cutting structure. 0 - NO LOST, WORN ANWOR BROKEN CUTnNG STRUCTURE. 8 - ALL OF CUTTING STRUCTURE LOST, WORN AND/OR BROKEN. DULL CHARACTERISTICS (Use only cutting structure related codes.) BC - Broken Cone LN - Lost Nonk BF - Bond Failure LT - Lost Taeth'Cuiters BT - Broken TaothICuttcn. OC - OffConterWear BU - Balled Up Bit PB - Plnch.d Bit CC - Cracked Cone PN - Pluggad Notzle/Flow Ps u o p CD - Cone Dragged RG - R0und.d Gaw CI - Cone interference RO - Ring Out CR - Cored SD - Shimail Damage CT - Chi ppd TWWCutWs SS - Sdf S h m i g Wear ER - Erosion TR - Tradclng FC - Flat Crested Wear WO - W a M Out Bit HC - Heat Checking WT - Worn TeetWCuttars JD - Junk Damage NO - No Dull Charactt~istic ' LC - Lostcone *Show cone # or#s w l e r location @. @ LOCATION ROLLER CONE N - Nose Row CONE # M - Middle Row 1 G - Gage Row 2 A - All Rows 3 @ BEARINGS I SEALS FIXED CUTTER C - Cone N - Nose T - Taper S - Shoulder G - Gage A - All Areas NON-SEALED BEARINGS SEALED BEARINGS A linear scale estimating bearing life E - seals effective used. (0 - No life used, 8 - All life F - seals failed used, ie. no bearing life remaining.) N - not able to grade X - fixed cutter bi @ Measure in fractions of an inch. (bearingless) I - in gage I l l 6 - Ills. out of gage 118 - l/Woutofgage 114 - 114'outofgage a OTHER DULL CHARACTERISTIC Refer to column 3 codes. @ REASON PULLED OR RUN TERMINATED BHA - Change Bottom Hok Assembly HR - Houn On Bit DMF - Downhok Motor Failure LOG - Run Logs DTF - Downhole Tool Failure PP - Pump Pressure DSF - Drill String Failure PR - Penetration Rate DST - Drill Stem Test RIG - Rig Repair DP - MI Plug TD - Total DepthlCasing Depth CU - Condition Mud TW - TwlstOff CP - Core Point TO - Torque FM - Formation Change WC - Weather Conditions HP - Hde Problems FOR ADDITIONAL INFORMATION CONTACT YWR LOCI1 UH - Left in Hole SECUAlTY DBS REPRESENTATIVE OR SECURTT Des DIVlSlON IN DALLAS, TEXAS (214) 333-321 1 Security DBS I nser t Bits ons may azger in parricular ar H04011 1/05 Produced by Halliburton Communications www. halliburton.coms O 2005 Halliburton All Rights Reserved Sales of Halliburton products and services will be in accord solely Printed in U.S.A. with the terms and conditions contained in the contract between HALLIBURTON Halliburton and the customer that is applicable to the sale. 1 f $3 L.. ' Security DBS IADC Classification Chart Steel Tooth Bits I I I strength and high drillability TI3 GTX-G3 SDGH MSlX MAX-GT3 MSDGH 3136 MX-3 MGGHt SVH MSVH FDGH, MFDGH 1 Medium to mediumhard formations with high compressive strength Hard semi-abrasive or abrasive formations In 1987, the Internafional Association of Drilling Contractors (IADC) initiated the use of a four-character IADC system for roller cone bits. In 1992, the system was expanded to include more features. I " 7C Code - 4th Character Classification -. 1; - - , . -.--- - - - - 4 4th Code Character eature 1, Security DBSNomenclature I w The system involves the combination of the traditional three-numeral system with a fourth alpha character. This fourth character more clearly defines additional features of roller cone bits with regard to cutting structures, bearings, seals, hydraulics and spec@ applications. The co& to the right are used in the fourth position of the fourth-character IADC bit classijication system. I M I Mntnr annlirntinn I - ther shape inserts -Prefix (unraUy preceeds bit number, others are suffrre) HALLIBURTON