Académique Documents
Professionnel Documents
Culture Documents
Description
Blade assembly
Lower boom assembly
Upper boom assembly
Knife
Mounting Bracket - used with
657-13 Kit
Mounting Bracket - Avenger used with 657-21 Kit
Hardware kit includes the
following:
HHCS, 7/16 - 20 x 3-1/4"
Carriage bolt 3/8 - 16 x 1"
Washer, Flat 3/8"
Lockwasher, 7/16"
Washer, Flat 1/2"
Washer, Flat 3/4"
HHCS, 3/4 - 10 x 5-1/2" Gr5
Eye Bolt, 3/8 -16
Description
Locknut, Nylon 3/8"-16
Locknut, Nylon 1/2"-20
Locknut, Nylon 3/4"-10
Spring, Extension
HHCS, 1/2 - 20 x 1.5" Gr5 Zn
Bushing 3/4 o.d. x 3/8 lg.
Shoe
Nut, Hex Fin 3/8 16 Zn
Plate, Spring Stop
PHMS, 10-24 x 3/4 Zn
Washer, .19 x .50 x .04 Zn
Locknut, Nylon 10-24 Zn
Block, Adjustment Pin
Spring, Comp. 0.66 x 1.92
Link, Quick - 3/8"
Tools Required
Ratchet with Sockets: 17mm, 19mm, 9/16", 5/8", 3/4", 1-1/8"
Combination Wrenches: 17mm, 19mm, 9/16", 3/4", 1-1/8"
External retaining ring pliers, grease
Detailed information on standard workshop and safety procedures, and general
installation practices is not included in these instructions, which have been prepared
to assist qualified and competent personnel. ODG assumes no responsibility or liability for PERSONAL INJURY or VEHICLE DAMAGE which results from any
procedure performed, including those procedures outlined in these instructions.
Before performing an installation operation, an individual must have determined
to his/her satisfaction that personal injury or vehicle damage will not result from
the installation procedure, working environment or tools selected.
Instructions:
1.
Verify that all components have been included as indicated in the list of parts on page 1 of these instructions.
3.
Remove the front tire assembly from each side of the vehicle using a 3/4" socket.
4.
Remove the front 3 bolts and flatwashers and REUSE when installing the 657-17 mounting brackets.
IMPORTANT: If the vehicle was equipped with tie downs at the front extension, do NOT reinstall
with the snow plow bracket. Mounting bolts will not be long enough to secure both.
Magnum, Conquest, Response, Bigfoot, Van2 (657-13 Kit)
When installing the 657-53 mounting brackets on older models, longer bolts are required. Secure with the
supplied 103-74 HHCS, 7/16 - 20 x 3-1/4"mounting bolts.
5.
Final Assembly
Follow detail drawings supplied to complete assembly. Please note revision as to how the winch hook is attached at
OPERATING GUIDELINES
1.
Do NOT operate the Argo on open or frozen bodies of water with the snowplow attached.
2.
For quick removal of the snowplow unit, disconnect the rear hitch points of the upper boom from the mounting
brackets, unhook and rewind the winch cable.
3.
The knives are specially designed to be reversible and interchangeable with each other once the leading edge
has worn.
NOTE: If the operator plans to use the Argo for extended periods without the snowplow, the operator
MUST remove the mounting brackets from the vehicle. Failure to do so could lead to damage to
the mounting brackets.
NOTE: Frequent usage of the plow will result in battery drain. The installation of an alternator kit is strongly
suggested.