Académique Documents
Professionnel Documents
Culture Documents
Mechanics of Material
Laboratory Report
Determined Beams AND Maxwell Theorem
Instructor: Mr. Sabbaghi
Prepared by: Seyed Ali Fatemi
2012-04
Brief Contents:
Introduction ---------------------------------------------------------------------------------- 2
First Stage ------------------------------------------------------------------------------------- 2
Second Stage---------------------------------------------------------------------------------- 5
Part 1 ------------------------------------------------------------------------------------------- 7
A ------------------------------------------------------------------------------------------------- 8
B ------------------------------------------------------------------------------------------------ 58
C ---------------------------------------------------------------------------------------------- 108
D ---------------------------------------------------------------------------------------------- 158
E ---------------------------------------------------------------------------------------------- 208
F ---------------------------------------------------------------------------------------------- 258
Part 2 ---------------------------------------------------------------------------------------- 308
Results and Questions ------------------------------------------------------------------ 322
At Last --------------------------------------------------------------------------------------- 329
Introduction:
In this report, our aim is to study the reactions of determined beams under
concentrated loads. At first stage well explain the term determined beam,
then the experiment procedure will be illustrated and it will be answered that
actually why we examine determined beams. In the next stage the diagrams and
data will be presented. Practical and theoretical and error altitudes will be
illustrated in tables. At last the specified questions will be answered. IT SLOULD
BE POINTED THAT THE NUMBERS ARE FIXED IN TWO DIGITS.
First Stage:
determining the internal forces is through the construction of shear force and
bending moment diagrams. Shear force is the internal force acting on a plane
perpendicular to the longitudinal axis of the beam. Bending moment is the
Once the type and location of the supports is defined, the shear force and
bending moment diagrams can be constructed for the loads applied to the
beam.
internal bending moment at all points along the length of the beam. From these
plots, the extreme values of shear and moment can be readily established.
Both normal and shear stresses are produced in a beam. Beam normal
stresses are computed from the flexure formula, which relates the internal
Beam
Second Stage:
Number
Material
Dimensions (mm)
E (GPa)
Aluminum 6061-T6
19.5*4*600
68.90
Brass C83400
30*4*600
101
Brass C83400
20*4*500
101
Brass C83400
25*4*500
101
Steel st37
25*3*600
200
25*4*500
200
structural
F
Steel st37
structural
Diagram
structure
Moment
diagram
Slope
diagram
Beam
diagram
Shear
stress
diagram
Deflection
Table
PART1: Determined
Beams
Examination Parts
PART2: Maxwell
Theorem
A)CL)
200g)
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.82<x-0.00>0 +1.14<x-600.00>0 - 1.96<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.82<x-0.00>1 +1.14<x-600.00>1 - 1.96<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.82/6<x-0.00>3 +1.14/6<x-600.00>3 - 40,534.38x1.96/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
10
400g)
11
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +2.29<x-600.00>0 - 3.92<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +2.29<x-600.00>1 - 3.92<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
12
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +2.29/6<x-600.00>3 - 81,068.75x3.92/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
13
600g)
14
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.45<x-0.00>0 +3.43<x-600.00>0 - 5.89<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.45<x-0.00>1 +3.43<x-600.00>1 - 5.89<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
15
121,603.13-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.45/6<x-0.00>3 +3.43/6<x-600.00>3 - 121,603.13x5.89/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
16
800g)
17
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.27<x-0.00>0 +4.58<x-600.00>0 - 7.85<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.27<x-0.00>1 +4.58<x-600.00>1 - 7.85<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
18
162,137.50-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.27/6<x-0.00>3 +4.58/6<x-600.00>3 - 162,137.50x7.85/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
19
20
A)CD)
200g)@100mm
21
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +0.33<x-600.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +0.33<x-600.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
22
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +0.33/6<x-600.00>3 - 29,975.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
23
200g)@200mm
24
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.31<x-0.00>0 +0.65<x-600.00>0 - 1.96<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.31<x-0.00>1 +0.65<x-600.00>1 - 1.96<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
25
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.31/6<x-0.00>3 +0.65/6<x-600.00>3 - 43,600.00x1.96/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
26
200g)@500mm
27
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.33<x-0.00>0 +1.64<x-600.00>0 - 1.96<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.33<x-0.00>1 +1.64<x-600.00>1 - 1.96<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
28
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.33/6<x-0.00>3 +1.64/6<x-600.00>3 - 19,075.00x1.96/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
29
400g)@100mm
30
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.27<x-0.00>0 +0.65<x-600.00>0 - 3.92<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.27<x-0.00>1 +0.65<x-600.00>1 - 3.92<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
31
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.27/6<x-0.00>3 +0.65/6<x-600.00>3 - 59,950.00x3.92/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
32
400g)@200mm
33
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.62<x-0.00>0 +1.31<x-600.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.62<x-0.00>1 +1.31<x-600.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
34
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.62/6<x-0.00>3 +1.31/6<x-600.00>3 - 87,200.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
35
400g)@500mm
36
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.65<x-0.00>0 +3.27<x-600.00>0 - 3.92<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.65<x-0.00>1 +3.27<x-600.00>1 - 3.92<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
37
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.65/6<x-0.00>3 +3.27/6<x-600.00>3 - 38,150.00x3.92/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
38
600g)@100mm
39
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.91<x-0.00>0 +0.98<x-600.00>0 - 5.89<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.91<x-0.00>1 +0.98<x-600.00>1 - 5.89<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
40
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.91/6<x-0.00>3 +0.98/6<x-600.00>3 - 89,925.00x5.89/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
41
600g)@200mm
42
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.92<x-0.00>0 +1.96<x-600.00>0 - 5.89<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.92<x-0.00>1 +1.96<x-600.00>1 - 5.89<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
43
130,800.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.92/6<x-0.00>3 +1.96/6<x-600.00>3 - 130,800.00x5.89/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
44
600g)@500mm
45
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.98<x-0.00>0 +4.91<x-600.00>0 - 5.89<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.98<x-0.00>1 +4.91<x-600.00>1 - 5.89<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
46
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.98/6<x-0.00>3 +4.91/6<x-600.00>3 - 57,225.00x5.89/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
47
800g)@100mm
48
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +6.54<x-0.00>0 +1.31<x-600.00>0 - 7.85<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +6.54<x-0.00>1 +1.31<x-600.00>1 - 7.85<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
49
119,900.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +6.54/6<x-0.00>3 +1.31/6<x-600.00>3 - 119,900.00x7.85/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
50
800g)@200mm
51
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +5.23<x-0.00>0 +2.62<x-600.00>0 - 7.85<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +5.23<x-0.00>1 +2.62<x-600.00>1 - 7.85<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
52
174,400.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +5.23/6<x-0.00>3 +2.62/6<x-600.00>3 - 174,400.00x7.85/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
53
800g)@500mm
54
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.31<x-0.00>0 +6.54<x-600.00>0 - 7.85<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.31<x-0.00>1 +6.54<x-600.00>1 - 7.85<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Slope discontinuity equation using symbolic notations:
55
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +7,165,598.49 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.31/6<x-0.00>3 +6.54/6<x-600.00>3 - 76,300.00x7.85/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
56
57
B)CL)
200g)
58
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.82<x-0.00>0 +1.14<x-600.00>0 - 1.96<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.82<x-0.00>1 +1.14<x-600.00>1 - 1.96<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
59
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.82/6<x-0.00>3 +1.14/6<x-600.00>3 - 40,534.38x1.96/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
60
400g)
61
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +2.29<x-600.00>0 - 3.92<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +2.29<x-600.00>1 - 3.92<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
62
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +2.29/6<x-600.00>3 - 81,068.75x3.92/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
63
600g)
64
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.45<x-0.00>0 +3.43<x-600.00>0 - 5.89<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.45<x-0.00>1 +3.43<x-600.00>1 - 5.89<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
65
121,603.13-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.45/6<x-0.00>3 +3.43/6<x-600.00>3 - 121,603.13x5.89/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
66
800g)
67
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.27<x-0.00>0 +4.58<x-600.00>0 - 7.85<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.27<x-0.00>1 +4.58<x-600.00>1 - 7.85<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
68
162,137.50-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.27/6<x-0.00>3 +4.58/6<x-600.00>3 - 162,137.50x7.85/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
69
70
B)CD)
200g)@100mm
71
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +0.33<x-600.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +0.33<x-600.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
72
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +0.33/6<x-600.00>3 - 29,975.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
73
200g)@200mm
74
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.31<x-0.00>0 +0.65<x-600.00>0 - 1.96<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.31<x-0.00>1 +0.65<x-600.00>1 - 1.96<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
75
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.31/6<x-0.00>3 +0.65/6<x-600.00>3 - 43,600.00x1.96/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
76
200g)@500mm
77
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.33<x-0.00>0 +1.64<x-600.00>0 - 1.96<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.33<x-0.00>1 +1.64<x-600.00>1 - 1.96<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
78
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.33/6<x-0.00>3 +1.64/6<x-600.00>3 - 19,075.00x1.96/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
79
400g)@100mm
80
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.27<x-0.00>0 +0.65<x-600.00>0 - 3.92<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.27<x-0.00>1 +0.65<x-600.00>1 - 3.92<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
81
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.27/6<x-0.00>3 +0.65/6<x-600.00>3 - 59,950.00x3.92/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
82
400g)@200mm
83
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.62<x-0.00>0 +1.31<x-600.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.62<x-0.00>1 +1.31<x-600.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
84
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.62/6<x-0.00>3 +1.31/6<x-600.00>3 - 87,200.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
85
400g)@500mm
86
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.65<x-0.00>0 +3.27<x-600.00>0 - 3.92<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.65<x-0.00>1 +3.27<x-600.00>1 - 3.92<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
87
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.65/6<x-0.00>3 +3.27/6<x-600.00>3 - 38,150.00x3.92/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
88
600g)@100mm
89
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.91<x-0.00>0 +0.98<x-600.00>0 - 5.89<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.91<x-0.00>1 +0.98<x-600.00>1 - 5.89<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
90
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.91/6<x-0.00>3 +0.98/6<x-600.00>3 - 89,925.00x5.89/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
91
600g)@200mm
92
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.92<x-0.00>0 +1.96<x-600.00>0 - 5.89<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.92<x-0.00>1 +1.96<x-600.00>1 - 5.89<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
93
130,800.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.92/6<x-0.00>3 +1.96/6<x-600.00>3 - 130,800.00x5.89/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
94
600g)@500mm
95
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.98<x-0.00>0 +4.91<x-600.00>0 - 5.89<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.98<x-0.00>1 +4.91<x-600.00>1 - 5.89<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
96
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.98/6<x-0.00>3 +4.91/6<x-600.00>3 - 57,225.00x5.89/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
97
800g)@100mm
98
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +6.54<x-0.00>0 +1.31<x-600.00>0 - 7.85<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +6.54<x-0.00>1 +1.31<x-600.00>1 - 7.85<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
99
119,900.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +6.54/6<x-0.00>3 +1.31/6<x-600.00>3 - 119,900.00x7.85/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
100
800g)@200mm
101
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +5.23<x-0.00>0 +2.62<x-600.00>0 - 7.85<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +5.23<x-0.00>1 +2.62<x-600.00>1 - 7.85<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
102
174,400.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +5.23/6<x-0.00>3 +2.62/6<x-600.00>3 - 174,400.00x7.85/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
103
800g)@500mm
104
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.31<x-0.00>0 +6.54<x-600.00>0 - 7.85<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.31<x-0.00>1 +6.54<x-600.00>1 - 7.85<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Slope discontinuity equation using symbolic notations:
105
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +16,159,996.60 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.31/6<x-0.00>3 +6.54/6<x-600.00>3 - 76,300.00x7.85/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
106
107
C)CL)
200g)
108
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.98<x-0.00>0 +0.98<x-500.00>0 - 1.96<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.98<x-0.00>1 +0.98<x-500.00>1 - 1.96<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
109
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.98/6<x-0.00>3 +0.98/6<x-500.00>3 - 30,656.25x1.96/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
110
400g)
111
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.96<x-0.00>0 +1.96<x-500.00>0 - 3.92<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.96<x-0.00>1 +1.96<x-500.00>1 - 3.92<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
112
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.96/6<x-0.00>3 +1.96/6<x-500.00>3 - 61,312.50x3.92/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
113
600g)
114
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.94<x-0.00>0 +2.94<x-500.00>0 - 5.89<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.94<x-0.00>1 +2.94<x-500.00>1 - 5.89<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
115
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.94/6<x-0.00>3 +2.94/6<x-500.00>3 - 91,968.75x5.89/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
116
800g)
117
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.92<x-0.00>0 +3.92<x-500.00>0 - 7.85<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.92<x-0.00>1 +3.92<x-500.00>1 - 7.85<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
118
122,625.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.92/6<x-0.00>3 +3.92/6<x-500.00>3 - 122,625.00x7.85/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
119
120
C)CD)
200g)@100mm
121
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.57<x-0.00>0 +0.39<x-500.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.57<x-0.00>1 +0.39<x-500.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
122
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.57/6<x-0.00>3 +0.39/6<x-500.00>3 - 23,544.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
123
200g)@200mm
124
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.18<x-0.00>0 +0.78<x-500.00>0 - 1.96<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.18<x-0.00>1 +0.78<x-500.00>1 - 1.96<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
125
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.18/6<x-0.00>3 +0.78/6<x-500.00>3 - 31,392.00x1.96/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
126
200g)@400mm
127
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.39<x-0.00>0 +1.57<x-500.00>0 - 1.96<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.39<x-0.00>1 +1.57<x-500.00>1 - 1.96<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
128
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.39/6<x-0.00>3 +1.57/6<x-500.00>3 - 15,696.00x1.96/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
129
400g)@100mm
130
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.14<x-0.00>0 +0.78<x-500.00>0 - 3.92<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.14<x-0.00>1 +0.78<x-500.00>1 - 3.92<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
131
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.14/6<x-0.00>3 +0.78/6<x-500.00>3 - 47,088.00x3.92/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
132
400g)@200mm
133
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.35<x-0.00>0 +1.57<x-500.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.35<x-0.00>1 +1.57<x-500.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
134
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.35/6<x-0.00>3 +1.57/6<x-500.00>3 - 62,784.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
135
400g)@400mm
136
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.78<x-0.00>0 +3.14<x-500.00>0 - 3.92<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.78<x-0.00>1 +3.14<x-500.00>1 - 3.92<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
137
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.78/6<x-0.00>3 +3.14/6<x-500.00>3 - 31,392.00x3.92/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
138
600g)@100mm
139
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.71<x-0.00>0 +1.18<x-500.00>0 - 5.89<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.71<x-0.00>1 +1.18<x-500.00>1 - 5.89<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
140
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.71/6<x-0.00>3 +1.18/6<x-500.00>3 - 70,632.00x5.89/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
141
600g)@200mm
142
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.53<x-0.00>0 +2.35<x-500.00>0 - 5.89<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.53<x-0.00>1 +2.35<x-500.00>1 - 5.89<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
143
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.53/6<x-0.00>3 +2.35/6<x-500.00>3 - 94,176.00x5.89/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
144
600g)@400mm
145
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.18<x-0.00>0 +4.71<x-500.00>0 - 5.89<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.18<x-0.00>1 +4.71<x-500.00>1 - 5.89<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
146
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.18/6<x-0.00>3 +4.71/6<x-500.00>3 - 47,088.00x5.89/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
147
800g)@100mm
148
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +6.28<x-0.00>0 +1.57<x-500.00>0 - 7.85<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +6.28<x-0.00>1 +1.57<x-500.00>1 - 7.85<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
149
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +6.28/6<x-0.00>3 +1.57/6<x-500.00>3 - 94,176.00x7.85/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
150
800g)@200mm
151
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.71<x-0.00>0 +3.14<x-500.00>0 - 7.85<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.71<x-0.00>1 +3.14<x-500.00>1 - 7.85<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
152
125,568.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.71/6<x-0.00>3 +3.14/6<x-500.00>3 - 125,568.00x7.85/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
153
800g)@400mm
154
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.57<x-0.00>0 +6.28<x-500.00>0 - 7.85<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.57<x-0.00>1 +6.28<x-500.00>1 - 7.85<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Slope discontinuity equation using symbolic notations:
155
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +10,773,331.06 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.57/6<x-0.00>3 +6.28/6<x-500.00>3 - 62,784.00x7.85/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
156
157
D)CL)
200g)
158
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.98<x-0.00>0 +0.98<x-500.00>0 - 1.96<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.98<x-0.00>1 +0.98<x-500.00>1 - 1.96<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
159
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.98/6<x-0.00>3 +0.98/6<x-500.00>3 - 30,656.25x1.96/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
160
400g)
161
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.96<x-0.00>0 +1.96<x-500.00>0 - 3.92<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.96<x-0.00>1 +1.96<x-500.00>1 - 3.92<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
162
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.96/6<x-0.00>3 +1.96/6<x-500.00>3 - 61,312.50x3.92/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
163
600g)
164
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.94<x-0.00>0 +2.94<x-500.00>0 - 5.89<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.94<x-0.00>1 +2.94<x-500.00>1 - 5.89<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
165
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.94/6<x-0.00>3 +2.94/6<x-500.00>3 - 91,968.75x5.89/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
166
800g)
167
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.92<x-0.00>0 +3.92<x-500.00>0 - 7.85<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.92<x-0.00>1 +3.92<x-500.00>1 - 7.85<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
168
122,625.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.92/6<x-0.00>3 +3.92/6<x-500.00>3 - 122,625.00x7.85/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
169
170
D)CD)
200g)@100mm
171
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.57<x-0.00>0 +0.39<x-500.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.57<x-0.00>1 +0.39<x-500.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
172
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.57/6<x-0.00>3 +0.39/6<x-500.00>3 - 23,544.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
173
200g)@200mm
174
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.18<x-0.00>0 +0.78<x-500.00>0 - 1.96<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.18<x-0.00>1 +0.78<x-500.00>1 - 1.96<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
175
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.18/6<x-0.00>3 +0.78/6<x-500.00>3 - 31,392.00x1.96/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
176
200g)@400mm
177
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.39<x-0.00>0 +1.57<x-500.00>0 - 1.96<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.39<x-0.00>1 +1.57<x-500.00>1 - 1.96<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
178
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.39/6<x-0.00>3 +1.57/6<x-500.00>3 - 15,696.00x1.96/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
179
400g)@100mm
180
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.14<x-0.00>0 +0.78<x-500.00>0 - 3.92<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.14<x-0.00>1 +0.78<x-500.00>1 - 3.92<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
181
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.14/6<x-0.00>3 +0.78/6<x-500.00>3 - 47,088.00x3.92/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
182
400g)@200mm
183
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.35<x-0.00>0 +1.57<x-500.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.35<x-0.00>1 +1.57<x-500.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
184
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.35/6<x-0.00>3 +1.57/6<x-500.00>3 - 62,784.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
185
400g)@400mm
186
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.78<x-0.00>0 +3.14<x-500.00>0 - 3.92<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.78<x-0.00>1 +3.14<x-500.00>1 - 3.92<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
187
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.78/6<x-0.00>3 +3.14/6<x-500.00>3 - 31,392.00x3.92/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
188
600g)@100mm
189
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.71<x-0.00>0 +1.18<x-500.00>0 - 5.89<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.71<x-0.00>1 +1.18<x-500.00>1 - 5.89<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
190
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.71/6<x-0.00>3 +1.18/6<x-500.00>3 - 70,632.00x5.89/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
191
600g)@200mm
192
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.53<x-0.00>0 +2.35<x-500.00>0 - 5.89<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.53<x-0.00>1 +2.35<x-500.00>1 - 5.89<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
193
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.53/6<x-0.00>3 +2.35/6<x-500.00>3 - 94,176.00x5.89/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
194
600g)@400mm
195
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.18<x-0.00>0 +4.71<x-500.00>0 - 5.89<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.18<x-0.00>1 +4.71<x-500.00>1 - 5.89<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
196
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.18/6<x-0.00>3 +4.71/6<x-500.00>3 - 47,088.00x5.89/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
197
800g)@100mm
198
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +6.28<x-0.00>0 +1.57<x-500.00>0 - 7.85<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +6.28<x-0.00>1 +1.57<x-500.00>1 - 7.85<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
199
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +6.28/6<x-0.00>3 +1.57/6<x-500.00>3 - 94,176.00x7.85/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
200
800g)@200mm
201
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.71<x-0.00>0 +3.14<x-500.00>0 - 7.85<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.71<x-0.00>1 +3.14<x-500.00>1 - 7.85<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
202
125,568.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.71/6<x-0.00>3 +3.14/6<x-500.00>3 - 125,568.00x7.85/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
203
800g)@400mm
204
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.57<x-0.00>0 +6.28<x-500.00>0 - 7.85<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.57<x-0.00>1 +6.28<x-500.00>1 - 7.85<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
205
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.57/6<x-0.00>3 +6.28/6<x-500.00>3 - 62,784.00x7.85/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
206
207
E)CL)
200g)
208
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.82<x-0.00>0 +1.14<x-600.00>0 - 1.96<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.82<x-0.00>1 +1.14<x-600.00>1 - 1.96<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
209
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.82/6<x-0.00>3 +1.14/6<x-600.00>3 - 40,534.38x1.96/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
210
400g)
211
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +2.29<x-600.00>0 - 3.92<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +2.29<x-600.00>1 - 3.92<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
212
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +2.29/6<x-600.00>3 - 81,068.75x3.92/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
213
600g)
214
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.45<x-0.00>0 +3.43<x-600.00>0 - 5.89<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.45<x-0.00>1 +3.43<x-600.00>1 - 5.89<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
215
121,603.13-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.45/6<x-0.00>3 +3.43/6<x-600.00>3 - 121,603.13x5.89/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
216
800g)
217
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-350.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.27<x-0.00>0 +4.58<x-600.00>0 - 7.85<x-350.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-350.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.27<x-0.00>1 +4.58<x-600.00>1 - 7.85<x-350.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
218
162,137.50-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-350.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.27/6<x-0.00>3 +4.58/6<x-600.00>3 - 162,137.50x7.85/6<x-350.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
219
220
E)CD)
200g)@100mm
221
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +0.33<x-600.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +0.33<x-600.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
222
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +0.33/6<x-600.00>3 - 29,975.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
223
200g)@200mm
224
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.31<x-0.00>0 +0.65<x-600.00>0 - 1.96<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.31<x-0.00>1 +0.65<x-600.00>1 - 1.96<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
225
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.31/6<x-0.00>3 +0.65/6<x-600.00>3 - 43,600.00x1.96/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
226
200g)@500mm
227
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.33<x-0.00>0 +1.64<x-600.00>0 - 1.96<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.33<x-0.00>1 +1.64<x-600.00>1 - 1.96<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
228
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.33/6<x-0.00>3 +1.64/6<x-600.00>3 - 19,075.00x1.96/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
229
400g)@100mm
230
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.27<x-0.00>0 +0.65<x-600.00>0 - 3.92<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.27<x-0.00>1 +0.65<x-600.00>1 - 3.92<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
231
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.27/6<x-0.00>3 +0.65/6<x-600.00>3 - 59,950.00x3.92/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
232
400g)@200mm
233
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.62<x-0.00>0 +1.31<x-600.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.62<x-0.00>1 +1.31<x-600.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
234
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.62/6<x-0.00>3 +1.31/6<x-600.00>3 - 87,200.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
235
400g)@500mm
236
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.65<x-0.00>0 +3.27<x-600.00>0 - 3.92<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.65<x-0.00>1 +3.27<x-600.00>1 - 3.92<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
237
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.65/6<x-0.00>3 +3.27/6<x-600.00>3 - 38,150.00x3.92/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
238
600g)@100mm
239
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.91<x-0.00>0 +0.98<x-600.00>0 - 5.89<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.91<x-0.00>1 +0.98<x-600.00>1 - 5.89<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
240
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.91/6<x-0.00>3 +0.98/6<x-600.00>3 - 89,925.00x5.89/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
241
600g)@200mm
242
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.92<x-0.00>0 +1.96<x-600.00>0 - 5.89<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.92<x-0.00>1 +1.96<x-600.00>1 - 5.89<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
243
130,800.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.92/6<x-0.00>3 +1.96/6<x-600.00>3 - 130,800.00x5.89/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
244
600g)@500mm
245
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.98<x-0.00>0 +4.91<x-600.00>0 - 5.89<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.98<x-0.00>1 +4.91<x-600.00>1 - 5.89<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
246
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.98/6<x-0.00>3 +4.91/6<x-600.00>3 - 57,225.00x5.89/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
247
800g)@100mm
248
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +6.54<x-0.00>0 +1.31<x-600.00>0 - 7.85<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +6.54<x-0.00>1 +1.31<x-600.00>1 - 7.85<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
249
119,900.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +6.54/6<x-0.00>3 +1.31/6<x-600.00>3 - 119,900.00x7.85/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
250
800g)@200mm
251
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +5.23<x-0.00>0 +2.62<x-600.00>0 - 7.85<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +5.23<x-0.00>1 +2.62<x-600.00>1 - 7.85<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
252
174,400.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +5.23/6<x-0.00>3 +2.62/6<x-600.00>3 - 174,400.00x7.85/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
253
800g)@500mm
254
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.31<x-0.00>0 +6.54<x-600.00>0 - 7.85<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.31<x-0.00>1 +6.54<x-600.00>1 - 7.85<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Slope discontinuity equation using symbolic notations:
255
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +11,249,997.63 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.31/6<x-0.00>3 +6.54/6<x-600.00>3 - 76,300.00x7.85/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
256
257
F)CL)
200g)
258
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.98<x-0.00>0 +0.98<x-500.00>0 - 1.96<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.98<x-0.00>1 +0.98<x-500.00>1 - 1.96<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
259
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.98/6<x-0.00>3 +0.98/6<x-500.00>3 - 30,656.25x1.96/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
260
400g)
261
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.96<x-0.00>0 +1.96<x-500.00>0 - 3.92<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.96<x-0.00>1 +1.96<x-500.00>1 - 3.92<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
262
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.96/6<x-0.00>3 +1.96/6<x-500.00>3 - 61,312.50x3.92/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
263
600g)
264
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.94<x-0.00>0 +2.94<x-500.00>0 - 5.89<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.94<x-0.00>1 +2.94<x-500.00>1 - 5.89<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
265
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.94/6<x-0.00>3 +2.94/6<x-500.00>3 - 91,968.75x5.89/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
266
800g)
267
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-250.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.92<x-0.00>0 +3.92<x-500.00>0 - 7.85<x-250.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-250.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.92<x-0.00>1 +3.92<x-500.00>1 - 7.85<x-250.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
268
122,625.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-250.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.92/6<x-0.00>3 +3.92/6<x-500.00>3 - 122,625.00x7.85/6<x-250.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
269
270
F)CD)
200g)@100mm
271
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.57<x-0.00>0 +0.39<x-500.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.57<x-0.00>1 +0.39<x-500.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
272
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.57/6<x-0.00>3 +0.39/6<x-500.00>3 - 23,544.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
273
200g)@200mm
274
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.18<x-0.00>0 +0.78<x-500.00>0 - 1.96<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.18<x-0.00>1 +0.78<x-500.00>1 - 1.96<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
275
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.18/6<x-0.00>3 +0.78/6<x-500.00>3 - 31,392.00x1.96/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
276
200g)@400mm
277
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.39<x-0.00>0 +1.57<x-500.00>0 - 1.96<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.39<x-0.00>1 +1.57<x-500.00>1 - 1.96<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
278
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.39/6<x-0.00>3 +1.57/6<x-500.00>3 - 15,696.00x1.96/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
279
400g)@100mm
280
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.14<x-0.00>0 +0.78<x-500.00>0 - 3.92<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.14<x-0.00>1 +0.78<x-500.00>1 - 3.92<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
281
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.14/6<x-0.00>3 +0.78/6<x-500.00>3 - 47,088.00x3.92/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
282
400g)@200mm
283
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.35<x-0.00>0 +1.57<x-500.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.35<x-0.00>1 +1.57<x-500.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
284
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.35/6<x-0.00>3 +1.57/6<x-500.00>3 - 62,784.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
285
400g)@400mm
286
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.78<x-0.00>0 +3.14<x-500.00>0 - 3.92<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.78<x-0.00>1 +3.14<x-500.00>1 - 3.92<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
287
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.78/6<x-0.00>3 +3.14/6<x-500.00>3 - 31,392.00x3.92/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
288
600g)@100mm
289
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.71<x-0.00>0 +1.18<x-500.00>0 - 5.89<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.71<x-0.00>1 +1.18<x-500.00>1 - 5.89<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
290
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.71/6<x-0.00>3 +1.18/6<x-500.00>3 - 70,632.00x5.89/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
291
600g)@200mm
292
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +3.53<x-0.00>0 +2.35<x-500.00>0 - 5.89<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +3.53<x-0.00>1 +2.35<x-500.00>1 - 5.89<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
293
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +3.53/6<x-0.00>3 +2.35/6<x-500.00>3 - 94,176.00x5.89/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
294
600g)@400mm
295
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.18<x-0.00>0 +4.71<x-500.00>0 - 5.89<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.18<x-0.00>1 +4.71<x-500.00>1 - 5.89<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
296
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.18/6<x-0.00>3 +4.71/6<x-500.00>3 - 47,088.00x5.89/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
297
800g)@100mm
298
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +6.28<x-0.00>0 +1.57<x-500.00>0 - 7.85<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +6.28<x-0.00>1 +1.57<x-500.00>1 - 7.85<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
299
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +6.28/6<x-0.00>3 +1.57/6<x-500.00>3 - 94,176.00x7.85/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
300
800g)@200mm
301
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +4.71<x-0.00>0 +3.14<x-500.00>0 - 7.85<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +4.71<x-0.00>1 +3.14<x-500.00>1 - 7.85<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
302
125,568.00-
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +4.71/6<x-0.00>3 +3.14/6<x-500.00>3 - 125,568.00x7.85/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
303
800g)@400mm
304
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-500.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.57<x-0.00>0 +6.28<x-500.00>0 - 7.85<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-500.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.57<x-0.00>1 +6.28<x-500.00>1 - 7.85<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Slope discontinuity equation using symbolic notations:
305
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +26,666,661.05 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-500.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.57/6<x-0.00>3 +6.28/6<x-500.00>3 - 62,784.00x7.85/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
306
307
308
309
PART1)
310
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-100.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +1.64<x-0.00>0 +0.33<x-600.00>0 - 1.96<x-100.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-100.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +1.64<x-0.00>1 +0.33<x-600.00>1 - 1.96<x-100.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
311
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-100.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +1.64/6<x-0.00>3 +0.33/6<x-600.00>3 - 29,975.00x1.96/6<x-100.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
312
PART2)
313
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-400.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.65<x-0.00>0 +1.31<x-600.00>0 - 1.96<x-400.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-400.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.65<x-0.00>1 +1.31<x-600.00>1 - 1.96<x-400.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
314
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-400.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.65/6<x-0.00>3 +1.31/6<x-600.00>3 - 34,880.00x1.96/6<x-400.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
315
PART3)
316
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-200.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +2.62<x-0.00>0 +1.31<x-600.00>0 - 3.92<x-200.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-200.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +2.62<x-0.00>1 +1.31<x-600.00>1 - 3.92<x-200.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
317
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-200.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +2.62/6<x-0.00>3 +1.31/6<x-600.00>3 - 87,200.00x3.92/6<x-200.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
318
PART4)
319
For the shear discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Shear discontinuity equation using symbolic notations:
Shear = Ay<x-0.00>0 +By<x-600.00>0 - P1<x-500.00>0
Shear discontinuity equation showing actual numeric values:
Shear = +0.65<x-0.00>0 +3.27<x-600.00>0 - 3.92<x-500.00>0
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the moment discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
Moment discontinuity equation using symbolic notations:
Moment = Ay<x-0.00>1 +By<x-600.00>1 - P1<x-500.00>1
Moment discontinuity equation showing actual numeric values:
Moment = +0.65<x-0.00>1 +3.27<x-600.00>1 - 3.92<x-500.00>1
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
For the slope discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Slope discontinuity equation using symbolic notations:
320
For the deflection discontinuity equation, the following units are displayed:
Length units = mm
Force units = N
Moment units = N-mm
EI = +13,466,663.83 N-mm
Deflection discontinuity equation using symbolic notations:
EI Deflection = Ay/6<x-0.00>3 +By/6<x-600.00>3 - (Slope at x=0) x P1/6<x-500.00>3
Deflection discontinuity equation showing actual numeric values:
EI Deflection = +0.65/6<x-0.00>3 +3.27/6<x-600.00>3 - 38,150.00x3.92/6<x-500.00>3
Note: Deflection computed from this equation is in units of mm.
When using discontinuity functions, if the term in the < > brackets is negative
for a particular value of x, the quantity in the < > brackets is defined to have a
value of zero.
321
322
ACL
Material A
Constant Load
Location experiment
And actually we must have some error considerations such as: default error
that comes from the measuring tool and system, error of default deflections of
beam, the equation error, vision error and errors of errors.
323
ACL)
As we see, the deviation of errors seems to be at same range; except the first
which is 27.15% that it could be of vision error.
Another point that should be mentioned is that first two steps of the
experiment are as the same range like the second pair. That could be of
changing the location of beam on the experiment set.
ACD)
In this state we see that the first error is proportionally large that could be of
vibration of experiment set. As we see in the next parts of experiment, the
ranges of errors are approximately the same that are default errors.
324
BCL)
BCD)
Like last experiments, as we see here we have big errors in first part, too;
which its reason mentioned.
Low altitude of errors in next stages shows that the beam is not deflected
and large part of error is of the measuring tool and the experiment set.
CCL)
At two parts of experiment, which are part 2 & 3, the ranges of errors are
approximately the same, which are default errors.
In part 4, we see that the altitudes of errors are low, which it could be the
error of error because of increasing the force.
CCD)
325
Like one of the results that brought before, we see a constant slope in errors
that comes from the primary deflection in beam.
DCL)
As we see, in the first experiment, there are some errors that seem to be
larger than the next experiments proportionally. This could because of set
vibrations and deflectometers. Actually the deflectometers have a default error
because of their structure and locations.
DCD)
326
As it was pointed before, the first experiment of each stage has large error
because of some problems that mentioned before. Here we see that error as
7.19%.
The others could because of equations, human vision and default
deflectometers error.
ECL)
Here as we see the error altitudes, it seems that the beam had primary
deflection.
Also the range of error altitudes shows us that we had vision errors in this
experiment.
327
328
ECD)
Except the first part of experiment that has large altitude of errors, which
could be of set vibrations; other error altitude parts are acceptable.
FCL)
In this experiment we have primary deflection in beam, too. But the 19.49%
error, which seems in first part of experiment, could be a vision error.
329
FCD)
Like other first step errors, it seems in this experiment too. Also we see the
proportionally large altitude of error at 200mm in all stages; which could be of
primary deflection.
At last:
Here we bring back the papers that had written at laboratory which signed
by instructor.
330