Académique Documents
Professionnel Documents
Culture Documents
iPASOLINK EX
CHAPTER I INSTALLATION
CONTENTS
OVERVIEW ..........................................................................................................................................1-1
ORIENTING ANTENNA.......................................................................................................................8-1
Installation
NWD-153831-01E
ii
CONTENTS
NWD-153831-01E
Installation
OVERVIEW
1-1
OVERVIEW
The standard installation is summarized in this section. Following shows the installation work flow.
Unpacking iPASOLINK EX
See Section3
Mounting iPASOLINK EX
See Section4
Connecting and Forming Cables
See Section5
Grounding the Frames
See Section6
Start up iPASOLINK EX
See Section7
WebLCT should be prepared here.
Refer to Chapter II Operation.
Antenna Orientation
See Section8
Installation
NWD-153831-01E
1-2
OVERVIEW
NWD-153831-01E
Installation
2-1
Following shows the list of iPASOLINK EX installation. Confirm them before starting the installation.
No.
Description
Drawing No.
TRP-80G1000MB-1A
Figure 2-1
Power cable
Figure 2-2
Installation
NWD-153831-01E
2-2
NWD-153831-01E
Installation
2-3
No.
Description
Drawing No.
Figure 2-3
Figure 2-4
Installation
NWD-153831-01E
2-4
NWD-153831-01E
Installation
UNPACKING iPASOLINK EX
3-1
UNPACKING IPASOLINK EX
Care Mark
2 Take out Power Cable and the iPASOLINK EX cushioning materials (pads) and poly sheet.
Power Cable
Top PAD
iPASOLINK EX
Poly Sheet
Bottom pad B
Bottom pad A
Installation
NWD-153831-01E
3-2
UNPACKING iPASOLINK EX
NWD-153831-01E
Installation
MOUNTING iPASOLINK EX
4-1
MOUNTINIG IPASOLINK EX
TOOLS
Screwdriver
Torque Wrench
NOTICE
1.
The other end of the Frame Ground (FG) should be connected to the
station earth point. For details, refer to 6. GROUNDING AND FORMING
CABLE section
Installation
NWD-153831-01E
MOUNTING iPASOLINK EX
4-2
Note: The details are referred to the installation manual which is attached the antenna.
NWD-153831-01E
Installation
MOUNTING iPASOLINK EX
4-3
Installation
NWD-153831-01E
MOUNTING iPASOLINK EX
4-4
NWD-153831-01E
Installation
5-1
5.1 Overview
This section provides the descriptions for connecting traffic cables, power cable and
frame ground cable.
3. Connect Ethernet Cables for the use of power supply and communication.
(1)
NOTE: When using -48V if you do not need. If you want to use as the
P1 Port a Communication Port, Please connect the P1 Port.
Installation
NWD-153831-01E
5-2
5.2.1 iPASOLINK EX
4 2
1 3
PORTS
No.
INDICATION
PURPOSE
FG
RX LEV MON
DCN
P4
P2/P3
P1(PoE)
DC-48V
NWD-153831-01E
Installation
5-3
FGterminal(M5
Installation
NWD-153831-01E
5-4
Insert the plug of Power Cable to the iPASOLINX EX and tighten the
Connector to the iPASOLINK EX with engage connector nut only using
fingers.
NWD-153831-01E
Installation
5-5
Installation
NWD-153831-01E
5-6
PoEPort
(Port1)
GbE/FEPort
OptPort
DCNPort
NWD-153831-01E
Installation
5-7
CAP (REAR)
CAP (FRONT)
Installation
NWD-153831-01E
5-8
WATERPROOFING CAP
NWD-153831-01E
Installation
5-9
UNLOCKED
LOCKED
5. Using the self-fusing tape, secure the removed port cap onto the
waterproofing cap of the Ethernet Cable.
Installation
NWD-153831-01E
5-10
1. Remove the bound cap away from the cables waterproofing cap.
This cap is used to protect the vacant port after disconnecting the Ethernet
Cable (in Step 3.)
NWD-153831-01E
Installation
5-11
LOCKED
UNLOCKED
3. Ensure to attach the waterproofing cap after disconnect the Ethernet Cable.
Installation
NWD-153831-01E
5-12
Indication:
P1/DCIN
Connector Type:
RJ-45
RJ-45
1
2
3
4
5
6
7
8
PIN No.
PoE+(PD) ASSIGNMENT
NWD-153831-01E
Installation
5-13
Indication:
P2
Connector Type:
RJ-45
RJ-45
1
2
3
4
5
6
7
8
PIN No.
GbE ASSIGNMENT
DA+
DA
DB+
DC+
DC
DB
DD+
DD
Installation
NWD-153831-01E
5-14
Indication:
P3,P4
Connector Type:
LC
1000BASE-SX/LX
PIN No.
Opt ASSIGNMENT
TX
RX
NWD-153831-01E
Installation
5-15
Indication:
LCT
Connector Type:
RJ-45
RJ-45
1
2
3
4
5
6
7
8
PIN No.
Installation
FE ASSIGNMENT
TD+
TD
RD+
RD
NWD-153831-01E
5-16
Pin8
Pin6
Pin7
Pin3
Pin1
Pin5
Pin4
Pin2
Figure 2-2 Pin Assign (Power Port)
Purpose
Ground
-48V
NWD-153831-01E
Installation
Pin7
5-17
Pin8
Pin6
Pin1
Pin3
Pin4
Pin5
Pin2
Purpose
Installation
NWD-153831-01E
5-18
NWD-153831-01E
Installation
6-1
When mounting iPASOLINK EX, ground the frame. The location of the ground terminal
on iPASOLINK EX method of Figure 6-1.
NOTES:
1. Connect the Frame Ground(FG) terminal on iPASOLINK EX to its rack using the erath
cable. In addition, connect the rack to the indoor earth terminal using the earth, and
connect the FG terminal in the iPASOLINK EX to the ground ( refer to Figure 6-1)
owerCable
Power Cable
Cautions:
1. Ensure to install iPASOLINK EX within the area protected by lightning rod.
2. To avoid surge currents caused by lightning circulating in the equipment earth
system,connect the equipment earth system (frame ground) to the ground of the lightning
rod at the ground level.
NOTES:
1.
2.
FrameGroundterminaloftheiPASOLINKEX(5mmsquarecable,whichmeansmorethan
2.5mmdiametercable;AWG#10)isrecommendedtoapplyfortheearthgrounding.The
properpressfixterminaltoolshallbeused.)
Screwtorqueshouldbewithin132kgfcm
Installation
NWD-153831-01E
6-2
Power Cable
Notes:
* NEC recommends that frame ground of iPASOLINK EX should be connected to earth
line as NECs standard installation.
EP Earth Ground Point of tower.
FG Frame Ground terminal of the iPASOLINK EX (5mm square cable (means more than
2.5mm diameter cable(AWG#10) is recommended to apply for the earth grounding. The
proper press fix terminal tool shall be used.)
NWD-153831-01E
Installation
7-1
CAUTION:
Equipment surface may be hot during the operation. Ensure not to
touch the equipment.
3. When the power is supplied, PWR LED (Green) and ONLINE LED(Green) at
DCN Port will blinking.
5. For the first time only, the equipment starts up disabling the radio output.
WARNING:
Once the equipment is powered on, wait at least 5 minutes before
turning its power off. Repeatedly turning the power on and off
within a short interval may cause the equipment failure.
Installation
NWD-153831-01E
7-2
1. Powering off the power supply or injector shuts down iPASOLINK EX.
WARNING:
Disconnecting Ethernet Cable from P1(PoE) Port while the
equipment is powered on may cause the equipment failure.
NWD-153831-01E
Installation
ORIENTING ANTENNA
8-1
ORIENTING ANTENNA
After the initial setup has been completed, an antenna orientation will be performed
between two stations according to the following procedure
8.1 Procedure
Apparatus
Connect the PC to the LCT port on the iPASOLINK EX using LAN cable (see
Operation manual),
Note
Click and select for the following control items in Maintenance Control,
Notes
1.
2.
TX Power Control:
(at opposite site)
At each station connect the digital multimeter to the RX LEV MON jack on the
iPASOLINK EX,
Installation
NWD-153831-01E
ORIENTING ANTENNA
8-2
At each station, adjust the azimuth and elevation angle of the antenna alternately
so that the measured voltage becomes maximum,
Note
4.5
3.5
2.5
2
1.5
1
0.5
0
-80
-70
-60
-50
-40
-30
-20
NWD-153831-01E
Installation
ORIENTING ANTENNA
8-3
Digital Multimeter
RX LEV MON
Notes
1.
2.
Note
The fixed bolts and nuts to be used for the antenna orientation differ with
antenna bracket types, refer to antenna bracket shown in Figure 8-2.
Installation
NWD-153831-01E
ORIENTING ANTENNA
8-4
A-1
A-2
A-3
A-4
A-5
A-6
1.
2.
3.
4.
NWD-153831-01E
Installation
ORIENTING ANTENNA
8-5
At each station, restore the MAINT Mode to off position using the LCT,
At each station, disconnect the digital multimeter from the RX LEV MON
connector,
Note
Installation
NWD-153831-01E
8-6
ORIENTING ANTENNA
NWD-115475-04E
Installation