Académique Documents
Professionnel Documents
Culture Documents
Features device:
1 - turn on and off at any of the channels.
2 - dimming the consecration of any of the channels.
3 - Turn on or off the general channels.
4 - total brightness control all the lighting channels .
5 - Standby timer off loads every 2, 4, 6, 8 hours or off.
6 - Select the type of load: Incandescent or energy saving.
7 - Channel selection switch, after turning off the power outlet.
Used 7 key keypad 1-4 ON and OFF button channel load, the 5th button to add brightness, 6th turn down the brightness, 7th overall switching on and off.
To register remote control commands to the device memory is necessary after power within 5 seconds press and hold for 4-7 seconds (it will match the first channel).
After that, should join the 1st channel, all other switches off. Next Next button remote it will be the 2nd channel. Similarly, 3 and 4-th channel.The following command will add
brightness. Before its programming must select the timer off loads for this: short pressing (0.1 - 0.5 seconds) Remote 1 - Channel 4 enables or disables the load.
Inclusion of each channel will correspond to 2 hours timer, so the sleep timer will be 2,4,6 or 8 hours. If all the load is turned off, and the timer is disabled. After you select the timer, select
the key remote, which will allow the brightness of the lamps, push and hold it for 4-7 seconds.After that, an inversion of the load.
The following command will turn down the brightness. Before its programming must select the type of load or energy saving lamp Filament for this: short pressing (0.1 - 0.5 seconds)
Remote 1 - Channel 4 enables or disables the load. Turning the channel will be for energy saving lamps and brightness of this channel will not be adjusted. For incandescent lamps turn
off the appropriate channel, in this case would be to adjust the brightness of incandescent lamps, select the key remote, which will diminish the brightness of the lamp, press and hold it for
4-7 seconds. After that, an inversion of the load.
The next and last team overall switching on and off loads. Before its programming must select which load will be turned on and the brightness of coca after power up, pick a key davim 4-7
seconds, and then all the lights will go out, then turn on for 2 seconds and then go out.This ending programming device. After this, the device is ready for operation. All teams in the flash
memory.
Device Management comes short press the remote device receives the command and compares with recorded in the memory IC. Adjusting the brightness occurs (the last turn on or off
the channel or the total incl.) + And - buttons.
The device can be integrated in the junction box or a chandelier. In one room, you can use multiple devices only when writing commands alternately close photodetectors devices.
The second option scheme for the triacs with a current of 5mA Control:
Below you can download the firmware source code and PCB ASM format Sprint-Layout
Type
Rating
Amount
Note
Shop
Scheme 1
MC PIC 8-bit
PIC12F629
Buy in store
BC846
Buy in store
Diode bridge
DB107
Buy in store
Zener diode
BZV85-C5V1
Optocoupler
MOC3023
BTA12
C1 Capacitor
1 uF 600
Buy in store
C2 Capacitor
100 nF
Buy in store
C3 Capacitor
10 nF
Buy in store
C4 Capacitor
220 uF
Buy in store
R1-R3 Resistor
5.1 Ohm
R5-R7 Resistor
390 Ohm
Buy in store
910 Ohm
Buy in store
10k
Buy in store
1k
Buy in store
150 ohms
Buy in store
T1-T4 Triac
5.1 In
Buy in store
Buy in store
BTA12-600B
1W
Buy in store
Buy in store
R9 Resistor
Polovni 7 kljunih tastature 1-4 ON i OFF kanala optereenja, gumb 5. dodati osvjetljenja, 6.
smanjite osvjetljenje, 7. ukupni ukljuivanje i iskljuivanje.
Za registraciju naredbe daljinskog upravljaa u memoriju ureaja potrebno je nakon
ukljuivanja u roku od 5 sekundi pritisnite i drite za 4-7 sekundi (to e odgovarati prvi
kanal).
Nakon toga, treba da se pridrue 1. kanal, svi ostali se iskljuuje. Slijedea Slijedea
daljinskom da e to biti na 2. kanalu. Slino tome, 3 i 4-og kanala. Sljedea naredba e dodati
osvjetljenja. Prije programskih mora odabrati timer iskljuen optereenja za ovu: kratki
pritiskom (0,1 - 0,5 sekunde) Daljinski 1 - Channel 4 omoguuje ili onemoguuje optereenja.
Ukljuivanje svaki kanal e odgovarati 2 sata timer, tako da je sleep timer e biti 2,4,6 ili 8
sati. Ako su svi teret je iskljuen, a timer je onemoguen. Nakon to izaberete tajmer,
odaberite kljune daljinskom, to e omoguiti osvjetljenje lampi, push i drite ga za 4-7
sekundi. Nakon toga, inverziju optereenja.
Sljedea naredba e se niz osvjetljenja. Prije programskih mora odabrati vrstu tereta ili
energetskih uteda lampa uarene niti za to: kratki pritiskom (0,1 - 0,5 sekunde) Daljinski 1 Channel 4 omoguuje ili onemoguuje optereenja. Okretanjem kanal e biti za utedu
energije lampe i ivost ovog kanala nee se prilagoditi. Za arulje sa arnom niti iskljuite
odgovarajui kanal, u ovom sluaju bi bilo za podeavanje osvjetljenja arulje sa arnom niti,
odaberite kljune daljinskom, to e umanjiti osvjetljenje lampe, pritisnite i drite ga za 4-7
sekundi. Nakon toga, inverziju optereenja.
Naredna i zadnja momad ukupne ukljuivanje i iskljuivanje optereenja. Prije svog
programa mora odabrati koje optereenje e biti ukljuena i osvjetljenje koke nakon
ukljuivanja se, javi kljuni Davim 4-7 sekunde, a onda sva svjetla e se ugasiti, a zatim
ukljuite za 2 sekunde, a zatim izai. Ovaj zavravaju programiranje ureaja. Nakon toga,
ureaj je spreman za rad. Svi timovi u flash memoriju.
Uprava ureaja dolazi kratko pritisnite daljinski ureaj prima naredbu i uporeuje sa
zabiljeen u memoriji IK. Podeavanje osvjetljenja javlja (posljednjih Ukljuivanje ili
iskljuivanje kanal ili ukupno uklj.) + I - tipke.
Ureaj se moe integrirati u razvodnoj kutiji ili luster. U jednoj sobi, moete koristiti vie
ureaja samo kod pisanja naredbi naizmjence blizu fotodetektori ureaja.