Académique Documents
Professionnel Documents
Culture Documents
1000320
Operating Instructions and
SPX Hydraulic Technologies
Parts List for:
TWSD Series
Working Pressure
and retracted, it is called a cycle.
The maximum working pressure for this hydraulic wrench is 10,000 psi (68,900 kPa). Make sure all hydraulic
Hydraulic Connections
equipment used with this wrench are rated for 10,000 psi (68,900 kPa) operating pressure.
IMPORTANT Loose or improperly threaded fittings can be potentially dangerous if pressurized, however,
over-tightening can cause premature thread failure. Fittings should only be tightened until
they are secure and leak-free.
For a copy of the calibration certificate for a specific torque wrench, email
info@powerteam.com with serial number of the torque wrench
Sheet No. 1 of 15
This is the safety alert symbol. WARNING To help prevent personal injury,
It is used to alert you to potential personal injury haz- • Always wear eye protection whenever operating
ards. Obey all safety messages that follow this sym- hydraulic equipment.
bol to avoid possible injury or death • Always wear hearing protection as required.
DANGER
• Operation, repair, or maintenance of hydraulic
equipment should be performed by a qualified
Denotes an imminently hazardous situation which, if person who understands the proper function of
not avoided, will result in death or serious injury. hydraulic equipment per local directives and
WARNING
standards.
• To prevent personal injury, use common sense. Do
Denotes a potentially hazardous situation which, if not not use any power equipment under the influence of
avoided, could result in death or serious injury. any mood altering substances.
CAUTION
• Never place your hands or other body parts near
a hydraulic fluid leak.
Never use your hands or other body parts to check
Denotes a potentially hazardous situation which, if not for a possible leak.
CAUTION
avoided, may result in minor or moderate injury.
High pressure fluid can be injected under your skin
causing serious injury and/or infection.
• Electric motors may spark, causing an explosion
Caution used without the safety alert symbol indicates when flammable materials are present. Do not
a potentially hazardous situation which, if not avoided, operate in an explosive atmosphere or in the pres-
may result in property damage. ence of conductive liquids. Use an air motor or
IMPORTANT
hand pump instead.
• To prevent electrical shock, make sure the
pump is properly grounded and the proper voltage
Denotes an operating or service procedure or condi- is being used.
WARNING
the wrench operator.
• Do not use hydraulic hoses, pump power, or remote
control cords as means of moving the equipment.
Read and understand this material before
operating or servicing this equipment. Failure • Make sure all hydraulic connections are securely
to understand how to safely operate this tool attached. Verify that the hydraulic hoses are not
could result in a accident causing serious injury kinked.
or death. • Remain clear of the reaction arm during operation.
• Only qualified operators should install, operate, Never put body parts between the reaction arm and
adjust, maintain, clean, repair, or transport this the reaction point.
machinery. • Always use top quality impact sockets in good condi-
• Inspect tool before use. Replace any worn or tion and remain clear of sockets during operation
damaged parts. Failure to observe these warnings because hidden flaws could cause breakage.
CAUTION
can result in severe injury or death. To prevent wrench damage,
• Keep work area clean and well lit. always use the properly sized tool
and accessories. Do not use a
• When not in use, wrenches and accessories wrench for anything other than the
should be properly stored to avoid deterioration. intended purpose.
Operating Instructions Form No. 1000320
Safety
A) Never exceed the torque wrench maximum working pressure (Advance 689 Bar / 10,000 psi, Retract 69
Bar / 1000 psi)
B) Keep hands and fingers clear of the torque wrench head and reaction arm area, before and during operation.
Fingers could be inadvertently trapped if care is not taken.
C) Keep other personnel clear of the working area and only allow trained personnel to use the equipment. Ideally
rope off the working area.
D) Prior to operation, ensure that all hoses, sockets and ancillary equipment is undamaged and fit for purpose.
Ensure that all torque wrench components (i.e. square drive, reaction arm, etc.) are properly attached and
secure. Ensure that the square drive retainer button is properly located.
E) Do not strike any of the components, including the socket, with a hammer in order to shock the nut free.
F) Check that reaction structures are strong and rigid enough to accept the torque tool reaction forces. Do not use
wedges, packing pieces, etc as a temporary reaction.
G) Take care when handling equipment. Quick connect couplings are especially susceptible to knocks and damage
and therefore care must be taken. Note that damaged couplings are difficult to connect. Do not force couplings.
I) Some torque wrenches (and sockets) weigh in excess of 20Kg, therefore Sheet No. 3 of 15
K) In some instances it may be necessary for the Operator to support the torque wrench whilst it is tightening, i.e.
upside down applications. If the torque tool cannot be strapped into position using ropes, etc, then the operator
must take the utmost care to avoid pinch points.
L) Never use the torque wrench with just one hose connected to the Advance port (port ‘A’). This will cause a pres-
sure intensification within the retract chamber possibly leading to tool damage. Always ensure that both hoses
are connected.
OPERATION
CAUTION For top performance, frequently inspect wrench, pump, and accessories for visual damage
Always follow instructions for proper wrench and pump maintenance.
Do not use other equipment to increase the capability (for example, hammering on socket wrench).
General
Each hydraulic wrench is supplied completely assembled and ready for use. A hydraulic pump is required to pro-
vide the speed and pressure that makes the hydraulic wrench system efficient and accurate.
Connectors at either end of the twin-line hose must not be modified or reversed.
WARNING Improper connection of hoses with the equipment could lead to equipment damage,
severe injury or death.
Electrical Connections
Make sure the power supply is compatible with the requirements of the electric pump motor. Minimize the length of
extension cords and be sure they are of adequate gauge and grounded.
Air Connections
Make sure the air flow rating is adequate and compatible prior to pressuring the pump. Make sure all connections
are tight and leak-free
Sheet No. 4 of 15
• Ensure that the reaction structure is suitably shaped to accommodate the reaction arm, Tapered surfaces are
generally unsuitable as the torque wrench tends to ‘ride up’ the taper, causing adverse tool loads. Flat surfaces
are most preferred.
• If in any doubt over the suitability of the reaction point, contact your torque wrench Supplier as various reaction
accessories are available which may prove more suitable.
• Don’t improvise. Packing pieces, spacers, etc. are dangerous and must never be used as a makeshift reaction
point.
Sheet No. 5 of 15
Use high quality, industrial impact sockets at all times. Ensure that sockets are rated to accept the full torque output
of the torque wrench that they are to be used with. Regularly check the socket for cracks and flaws, if any sign of
damage is evident, discard it immediately as a damaged socket breaking under load could cause equipment dam-
age or Operator injury.
Long reach or deep sockets are not recommended for use with hydraulic torque tools, as they tend to make the
wrench and socket unstable. However, some applications demand the use of long reach sockets, therefore it is
imperative that support is provided for both the socket and reaction facility. The same applies to socket accessories
such as extension bars, knuckle joints (not recommended), etc.
Setting Torque
Setting up the equipment only takes a few minutes and some simple checks during set up will aid in the success of
the torquing operation.
• Obtain the torque value that is to be used for the tightening operation.
• Ensure that the bolt threads, nut threads and nut to flange contact faces are liberally coated with anti-seize lubri-
cant of known friction co-efficient. Ensure that the lubricant friction co-efficient matches that which has been used
to derive the torque value.
• Make sure that the torque wrench is suitable to deliver the required torque. Should the torque value exceed 80%
of the torque wrench output, consider using a higher capacity torque wrench.
• Use the ‘Pressure – Torque Conversion Chart’ for the particular torque wrench to be used (supplied with the
torque wrench) to obtain the required pump pressure.
• Make sure that the socket to be used is of the correct type and size. A poor fitting or oversize socket will damage
nuts, induce inaccurate bolt loads and possible cause operator injury.
• Place the proper size impact socket on the square drive and secure it properly with the locking ring and pin.
Make sure the square drive is fully engaged into the socket.
• Place the wrench and socket on the nut. Make sure the socket is fully engaged on the nut.
• Make sure the reaction arm is placed firmly against a stationary object such as an adjacent nut, flange, equip-
ment housing, etc.
NOTE: When positioning the wrench, make sure the hose connection will not hit any stationary object. This may
result in snapping a hose connection or breaking the coupler connection.
Sheet No. 6 of 15
Tightening
1. Connect the torque wrench to the pump unit. Ensure that the couplings are fully screwed together as they are
self-sealing and will restrict oil flow if not fully connected.
NOTE : TWSD torque wrenches are equipped with a pressure release valve built into the Multi-Axis Swivel
Manifold to protect against retract pressure intensification should the retract port hydraulic coupling not be fully con-
nected, or become loose during use. If an intensification occurs, the valve will bleed hydraulic oil externally from the
manifold yoke. Note that oil bleeding from the swivel manifold is not a sign of seal leakage.
2. Prior to applying the torque wrench (and socket) to the application, the pump output pressure must be pre-set to
relieve at the pressure obtained from the ‘Pressure – Torque Conversion Chart’. This can be done with the
torque wrench connected to the pump and resting on the floor or bench. Applying advance pressure to the
torque wrench will extend the piston until it reaches the end of its stroke whereby the pump pressure will build.
Holding the wrench at the end of its stroke will allow the pump pressure to be adjusted. Retract the torque
wrench piston and advance again making sure that the pump relieves at the desired pressure setting.
Blanking the pump outlets using blank couplings can also be done to carry out the pump pressure setting.
NOTE : Allow time for the wrench to retract. If another advance stroke is made before the torque wrench has fully
retracted, the ratchet mechanism may not engage correctly, causing it to jump a ratchet tooth (probably damaging
the ratchet). Before applying another advance stroke, make sure that the pump is idling at 69 Bar (1000psi), which
indicates full retraction.
3. Apply the torque wrench and socket to the nut to be tightened, ensuring that the reaction arm butts firmly and
squarely against the selected reaction point.
Sheet No. 7 of 15
5. Several forward strokes are made until the nut ceases to rotate during the stroke, (known as stalling), but bear
in mind that nut rotation will always cease at the end of the wrench stroke and must not be confused with the
wrench stalling. WHEN THE WRENCH STALLS, APPLY ANOTHER FORWARD STROKE AND OBSERVE THE
PUMP PRESSURE GAUGE, WHICH SHOULD READ THE DESIRED PRE-SET PRESSURE.
6. Retract the torque wrench, stop the pump unit, and remove from the nut
Loosening Bolts
1. Connect the torque wrench to the pump unit. Ensure that the couplings are fully screwed together as they are
self-sealing and will restrict oil flow if not fully connected.
2. Prior to applying the torque wrench (and socket) to the application, the pump output pressure must be pre-set to
deliver the maximum pressure of 690 Bar (10,000psi). This can be done with the torque wrench connected to
the pump and resting on the floor or bench. Applying advance pressure to the torque wrench will extend the pis-
ton until it reaches the end of its stroke whereby the pump pressure will build. Holding the wrench at the end of
its stroke will allow the pump pressure to be adjusted. Retract the torque wrench piston and advance again
making sure that the pump delivers full pressure.
Blanking the pump outlets using blank couplings can also be done to carry out the pump pressure setting.
3. Apply the torque wrench and socket to the nut to be loosened, ensuring that the reaction arm butts firmly and
squarely against the selected reaction point.
4. Start the pump and advance the torque wrench. As the wrench strokes forward the reaction arm will press
against the reaction point. As the pump pressure builds (and thus torque applied to the nut), the nut will break
free. Once the nut has been released, remove the nut by hand if loose enough, or alternatively use an impact
wrench, it is not recommended to use the torque wrench.
NOTE: Should maximum pump pressure be reached, and the nut has still not broken free, use a higher capacity torque tool
(providing that the nut/bolt material will accept the higher torques without damage). Do not, under any circumstances, strike
the socket or torque wrench in an attempt to ‘shock’ the nut free.
5. Retract the torque wrench, stop the pump unit, and remove from the nut.
Loosening of bolts using torque tools can be unpredictable and often unsuccessful, especially if the nuts and bolts
are severely corroded. However, some measures can be carried out to increase the success rate of nut breakout.
• In general, loosening mildly rusted bolts requires up to twice the make up torque to release the nut. Heavily cor-
roded bolts may take up to three times the make up torque. Ensure that the bolt and nut material is strong
enough to accept these higher torques.
• Remove surface rust and scale using a wire brush. Apply releasing oil to the nut, bolt and bearing face, and allow
time for the release oil to soak in and penetrate.
Sheet No. 8 of 15
• Never strike the socket or torque wrench in an attempt to ‘shock’ the nut free. This will cause damage to the
socket and torque wrench, and could result in operator injury. Evidence of torque wrench abuse will invalidate the
Manufacturer’s Warranty.
The torquing procedure is compiled around using a single torque wrench, the object of the procedure being to
accurately achieve a pre-determined residual bolt stress.
Sheet No. 9 of 15
Post-Use Maintenance
In order to keep the TWSD torque wrench in good working condition, it is recommended that simple post-use main-
tenance be carried following each period of use.
3. It is preferable to lightly spray the torque wrench with water repellent spray (WD40), prior to placing back into
storage.
Sheet No. 10 of 15
Sheet No. 11 of 15
Cylinder will not advance. 1. Coupling not fully mated 1. Check coupling
2. Cylinder seal leakage 2. Replace seal
Cylinder will not retract. 3. Pump unit 3. Check pump unit
4. Faulty coupling 4. Replace coupling
Torque wrench operates 1. Reversed couplings. 1. Check pump, hose and torque
backwards wrench for cross connection
Torque wrench does not ratchet 1. Broken drive shoe 1. Replace drive shoe
2. Jammed drive shoe 2. Check drive shoe and spring
3. Damaged ratchet 3. Check / replace ratchet
Ratchet jumps whilst driving 1. Worn / damaged ratchet 1. Replace ratchet and drive shoe
2. Worn / damaged drive shoe 2. Replace ratchet and drive shoe
3. Wrench incorrectly retracted 3. Allow time to fully retract.
4. Weak / snapped drive shoe spring. 4. Replace springs
Sheet No. 12 of 15
46
50
20
1000082
45
44
41
18
19
33
31
30 37
31 4
34 33
27 13
40 22
17 3 42
26
29 35
43 28 24
2
14
25
38
21
36 10
9
23
11
32
13
12
42 39
16
48 1
47
15
5
Sheet No. 13 of 15
TWSD3-P24
24 1 SEAL KIT, TWSD3 BODY
NO. QTY. SPX P/N DESCRIPTION
TWSD1-P01 TWSD3-P24
25 1 SEAL KIT, TWSD3 BODY
TWSD1-P02 TWSD3-P24
1 1 BODY, TWSD1 26 1 SEAL KIT, TWSD3 BODY
TWSD1-P03 TWLC2-P14
2 1 PISTON, TWSD1 27 1 SEAL KIT, TWSD3 BODY
TWSD1-P04 TWLC2-P14
3 1 PLUG, TWSD1 PISTON 28 1 SEAL KIT, TWLC2 MULTI-SWIVEL
TWSD1-P05 TWLC2-P14
4 1 ENDCAP, TWSD1 29 2 SEAL KIT, TWLC2 MULTI-SWIVEL
TWSD1-P06 TWLC2-P14
5 1 CRANK, TWSD1 30 3 SEAL KIT, TWLC2 MULTI-SWIVEL
TWSD1-P07 TWL4-041-P05
6 1 RATCHET, TWSD1 31 4 SEAL KIT, TWLC2 MULTI-SWIVEL
TWSD1-P08 TWLC2-P22
7 1 SHOE, TWSD1 DRIVE 32 2 SPRING, TWL4-041
TWSD1-P09 TWLC2-P23
8 1 DRIVER, TWSD1 SQUARE 33 2 PLUG, TWLC2
TWSD1-P10 TWSD3-P35
9 1 SLIDER, TWSD1 34 4 SCREW, TWLC2
TWSD1-P11 TWSD1-P36
10 1 SHUTTLE, TWSD1 35 1 SCREW, TWSD3
TWSD1-P12 TWLC2-P25
11 1 PIN, TWSD1 CRANK RETAINING 36 1 SCREW, TWSD1
TWSD1-P13 TWSD1-P38
12 1 CAP, TWSD1 SQUARE DRIVER 37 1 SCREW, TWLC2
1000305 TWSD3-P39
13 2 BUTTON ASSY, TWSD1 LOCK 38 2 SCREW, TWSD1
1000310 TWSD3-P40
14 1 DECAL, TWSD1 PT BRAND 39 2 PIN, TWSD3
1000315 TWLC2-P26
15 1 DECAL, TWSD1 PT SIDE 40 1 CLIP, TWSD3
TWLC2-P07 TWSD1-P42
16 1 DECAL, TWSD1 PD SIDE 41 1 CLIP, TWLC2
TWLC2-P08 TWSD3-P43
17 1 POST, TWLC2 MULTI-SWIVEL 42 2 CLIP, TWSD1
TWLC2-P09 TWLC2-P28
18 1 BANJO, TWLC2 MULTI-SWIVEL 43 2 SCREW, TWSD3
TWLC2-P10 TWLC2-P29
19 1 YOKE, TWLC2 MULTI-SWIVEL ADVANCE 44 1 ADAPTOR, TWLC2
TWSD1-P21 TWLC2-P30
20 1 YOKE, TWLC2 MULTI-SWIVEL RETRACT 45 1 COUPLING, TWLC2 MALE
TWSD1-P22 TWSD3-P47
21 1 REACTION ARM, TWSD1 46 1 COUPLING, TWLC2 FEMALE
TWSD1-P23 1000323
22 1 PLATE, TWSD1 REACTION ARM BUTTON 47 2 JOURNAL, TWSD3 SIDE PLATE
TWSD1-P24 1000079
23 1 PAD, TWSD1 REACTION ARM 48 1 DECAL, TW C.O.O
TWSD1-P24 1000082
24 1 SEAL KIT, TWSD1 BODY 49 1 DECAL, TORQUE WRENCH WARNING
TWSD1-P24 1000083
25 1 SEAL KIT, TWSD1 BODY 50 1 DECAL, TORQUE WRENCH WARNING
TWSD1-P24 251057
26 1 SEAL KIT, TWSD1 BODY 51 1 DECAL, TORQUE WRENCH WARNING
TWLC2-P14
TWSD6
27 1 SEAL KIT, TWSD1 BODY 52 1 DECAL, WARNING
TWLC2-P14
28 1 SEAL KIT, TWLC2 MULTI-SWIVEL ITEM
TWLC2-P14
29 2 SEAL KIT, TWLC2 MULTI-SWIVEL NO. QTY. SPX P/N DESCRIPTION
TWLC2-P14
30 3 SEAL KIT, TWLC2 MULTI-SWIVEL
TWL2-032-P05 TWSD6-P01
31 4 SEAL KIT, TWLC2 MULTI-SWIVEL
TWLC2-P22 TWSD6-P02
32 2 SPRING, TWL2-032 1 1 BODY, TWSD6
TWLC2-P23 TWSD6-P03
33 2 PLUG, TWLC2 2 1 PISTON, TWSD6
TWSD1-P35 TWSD6-P04
34 4 SCREW, TWLC2 3 1 PLUG, TWSD6 PISTON
TWSD1-P36 TWSD6-P05
35 1 SCREW, TWSD1 4 1 ENDCAP, TWSD6
TWLC2-P25 TWSD6-P06
36 1 SCREW, TWSD1 5 1 CRANK, TWSD6
TWSD1-P38 TWSD6-P07
37 1 SCREW, TWLC2 6 1 RATCHET, TWSD6
TWSD1-P39 TWSD6-P08
38 2 SCREW, TWSD1 7 1 SHOE, TWSD6 DRIVE
TWSD1-P40 TWSD6-P09
39 2 PIN, TWSD1 8 1 DRIVER, TWSD6 SQUARE
TWLC2-P26 TWSD6-P10
40 1 CLIP, TWSD1 9 1 SLIDER, TWSD6
TWSD1-P42 TWSD6-P11
41 1 CLIP, TWLC2 10 1 SHUTTLE, TWSD6
TWSD1-P43 TWSD6-P12
42 2 CLIP, TWSD1 11 1 PIN, TWSD6 CRANK RETAINING
TWLC2-P28 TWSD6-P13
43 2 SCREW, TWSD1 12 1 CAP, TWSD6 SQUARE DRIVER
TWLC2-P29 1000307
44 1 ADAPTOR, TWLC2 13 2 BUTTON ASSY, TWSD6 LOCK
TWLC2-P30 1000312
45 1 COUPLING, TWLC2 MALE 14 1 DECAL, TWSD6 PT BRAND
TWSD1-P47 1000317
46 1 COUPLING, TWLC2 FEMALE 15 1 DECAL, TWSD6 PT SIDE
1000323 TWLC8-P08
47 2 JOURNAL, TWSD1 SIDE PLATE 16 1 DECAL, TWSD6 PD SIDE
1000079 TWLC8-P08
48 1 DECAL, TW C.O.O 17 1 POST, TWLC8 MULTI-SWIVEL
1000082 TWLC8-P10
49 1 DECAL, TORQUE WRENCH WARNING 18 1 POST, TWLC8 MULTI-SWIVEL
1000083 TWLC8-P11
50 1 DECAL, TORQUE WRENCH WARNING 19 1 YOKE, TWLC8 MULTI-SWIVEL ADVANCE
251057 TWSD6-P21
51 1 DECAL, TORQUE WRENCH WARNING 20 1 YOKE, TWLC8 MULTI-SWIVEL RETRACT
TWSD6-P22
52 1 DECAL, WARNING 21 1 REACTION ARM, TWSD6
TWSD6-P23
TWSD3
22 1 PLATE, TWSD6 REACTION ARM BUTTON
TWSD6-P24
23 1 PAD, TWSD6 REACTION ARM
TWSD6-P24
ITEM 24 1 SEAL KIT, TWSD6 BODY
TWSD6-P24
NO. QTY. SPX P/N DESCRIPTION 25 1 SEAL KIT, TWSD6 BODY
TWSD3-P01 TWSD6-P24
26 1 SEAL KIT, TWSD6 BODY
TWSD3-P02 TWLC8-P15
1 1 BODY, TWSD3 27 1 SEAL KIT, TWSD6 BODY
TWSD3-P03 TWLC8-P15
2 1 PISTON, TWSD3 28 1 SEAL KIT, TWLC8 MULTI-SWIVEL
TWSD3-P04 TWLC8-P15
3 1 PLUG, TWSD3 PISTON 29 3 SEAL KIT, TWLC8 MULTI-SWIVEL
TWSD3-P05 TWLC8-P15
4 1 ENDCAP, TWSD3 30 3 SEAL KIT, TWLC8 MULTI-SWIVEL
TWSD3-P06 TWL4-041-P05
5 1 CRANK, TWSD3 31 4 SEAL KIT, TWLC8 MULTI-SWIVEL
TWSD3-P07 TWLC8-P23
6 1 RATCHET, TWSD3 32 2 SPRING, TWL4-041
TWSD3-P08 TWLC2-P23
7 1 SHOE, TWSD3 DRIVE 33 2 PLUG, TWLC8
TWSD3-P09 TWSD6-P35
8 1 DRIVER, TWSD3 SQUARE 34 4 SCREW, TWLC2
TWSD3-P10 TWSD6-P36
9 1 SLIDER, TWSD3 35 1 SCREW, TWSD6
TWSD3-P11 TWLC2-P25
10 1 SHUTTLE, TWSD3 36 1 SCREW, TWSD6
TWSD3-P12 TWSD6-P38
11 1 PIN, TWSD3 CRANK RETAINING 37 1 SCREW, TWLC2
TWSD1-P13 TWSD6-P39
12 1 CAP, TWSD3 SQUARE DRIVER 38 2 SCREW, TWSD6
1000306 TWSD6-P40
13 2 BUTTON ASSY, TWSD1 LOCK 39 2 PIN, TWSD6
1000311 TWLC8-P27
14 1 DECAL, TWSD3 PT BRAND 40 1 CLIP, TWSD6
1000316 TWSD6-P42
15 1 DECAL, TWSD3 PT SIDE 41 1 CLIP, TWLC8
TWLC2-P07
16 1 DECAL, TWSD3 PD SIDE 42 2 CLIP, TWSD6
Sheet No. 14 of 15
TWLC2-P08
17 1 POST, TWLC2 MULTI-SWIVEL
TWLC2-P09
18 1 BANJO, TWLC2 MULTI-SWIVEL
TWLC2-P10
19 1 YOKE, TWLC2 MULTI-SWIVEL ADVANCE
TWSD3-P21
Rev Date: 29 Feb 2008
20 1 YOKE, TWLC2 MULTI-SWIVEL RETRACT
TWSD3-P22
21 1 REACTION ARM, TWSD3
22 1 PLATE, TWSD3 REACTION ARM BUTTON
Parts List Form No. 1000320
ITEM TWSD6 (continued) ITEM TWSD25
NO. QTY. SPX P/N DESCRIPTION NO. QTY. SPX P/N DESCRIPTION
TWSD3-P43 TWSD25-P01
TWLC2-P28 TWSD25-P02
43 2 SCREW, TWSD3 1 1 BODY, TWSD25
TWLC2-P29 TWSD25-P03
44 1 ADAPTOR, TWLC2 2 1 PISTON, TWSD25
TWLC2-P30 TWSD25-P04
45 1 COUPLING, TWLC2 MALE 3 1 PLUG, TWSD25 PISTON
TWSD6-P47 TWSD25-P05
46 1 COUPLING, TWLC2 FEMALE 4 1 ENDCAP, TWSD25
1000323 TWSD25-P06
47 2 JOURNAL, TWSD6 SIDE PLATE 5 1 CRANK, TWSD25
1000079 TWSD25-P07
48 1 DECAL, TW C.O.O 6 1 RATCHET, TWSD25
1000082 TWSD25-P08
49 1 DECAL, TORQUE WRENCH WARNING 7 1 SHOE, TWSD25 DRIVE
1000083 TWSD25-P09
50 1 DECAL, TORQUE WRENCH WARNING 8 1 DRIVER, TWSD25 SQUARE
251057 TWSD25-P10
51 1 DECAL, TORQUE WRENCH WARNING 9 1 SLIDER, TWSD25
TWSD25-P11
TWSD11
52 1 DECAL, WARNING 10 1 SHUTTLE, TWSD25
TWSD25-P12
11 1 PIN, TWSD25 CRANK RETAINING
TWSD25-P13
ITEM 12 1 CAP, TWSD25 SQUARE DRIVER
1000309
NO. QTY. SPX P/N DESCRIPTION 13 2 BUTTON ASSY, TWSD25 LOCK
TWSD1-P11 1000314
14 1 DECAL, TWSD25 PT BRAND
TWSD1-P12 1000319
1 1 PIN, TWSD1 CRANK RETAINING 15 1 DECAL, TWSD25 PT SIDE
TWSD1-P13 TWLC8-P08
2 1 CAP, TWSD1 SQUARE DRIVER 16 1 DECAL, TWSD25 PD SIDE
1000305 TWLC8-P08
3 2 BUTTON ASSY, TWSD1 LOCK 17 1 POST, TWLC8 MULTI-SWIVEL
1000310 TWLC8-P10
4 1 DECAL, TWSD1 PT BRAND 18 1 POST, TWLC8 MULTI-SWIVEL
1000315 TWLC8-P11
5 1 DECAL, TWSD1 PT SIDE 19 1 YOKE, TWLC8 MULTI-SWIVEL ADVANCE
TWLC2-P07 TWSD25-P21
6 1 DECAL, TWSD1 PD SIDE 20 1 YOKE, TWLC8 MULTI-SWIVEL RETRACT
TWLC2-P08 TWSD25-P22
7 1 POST, TWLC2 MULTI-SWIVEL 21 1 REACTION ARM, TWSD25
TWLC2-P09 TWSD25-P23
8 1 BANJO, TWLC2 MULTI-SWIVEL 22 1 PLATE, TWSD25 REACTION ARM BUTTON
TWSD11-P10 TWSD25-P24
9 1 YOKE, TWLC2 MULTI-SWIVEL ADVANCE 23 1 PAD, TWSD25 REACTION ARM
TWSD11-P11 TWSD25-P24
10 1 SHUTTLE, TWSD11 24 1 SEAL KIT, TWSD25 BODY
TWSD11-P12 TWSD25-P24
11 1 PIN, TWSD11 CRANK RETAINING 25 1 SEAL KIT, TWSD25 BODY
TWSD11-P13 TWSD25-P24
12 1 CAP, TWSD11 SQUARE DRIVER 26 1 SEAL KIT, TWSD25 BODY
1000308 TWLC8-P15
13 2 BUTTON ASSY, TWSD11 LOCK 27 1 SEAL KIT, TWSD25 BODY
1000313 TWLC8-P15
14 1 DECAL, TWSD11 PT BRAND 28 1 SEAL KIT, TWLC8 MULTI-SWIVEL
1000318 TWLC8-P15
15 1 DECAL, TWSD11 PT SIDE 29 2 SEAL KIT, TWLC8 MULTI-SWIVEL
TWLC8-P08 TWLC8-P15
16 1 DECAL, TWSD11 PD SIDE 30 3 SEAL KIT, TWLC8 MULTI-SWIVEL
TWLC8-P08 TWL30-080-P05
17 1 POST, TWLC8 MULTI-SWIVEL 31 4 SEAL KIT, TWLC8 MULTI-SWIVEL
TWLC8-P10 TWLC8-P23
18 1 POST, TWLC8 MULTI-SWIVEL 32 2 SPRING, TWL30-080
TWLC8-P11 TWLC2-P23
19 1 YOKE, TWLC8 MULTI-SWIVEL ADVANCE 33 2 PLUG, TWLC8
TWSD11-P21 TWL15-070-P06
20 1 YOKE, TWLC8 MULTI-SWIVEL RETRACT 34 4 SCREW, TWLC2
TWSD11-P22 TWSD6-P36
21 1 REACTION ARM, TWSD11 35 1 SCREW, TWL15-070
TWSD11-P23 TWLC2-P25
22 1 PLATE, TWSD11 REACTION ARM BUTTON 36 1 SCREW, TWSD6
TWSD11-P24 TWSD25-P38
23 1 PAD, TWSD11 REACTION ARM 37 1 SCREW, TWLC2
TWSD11-P24 TWSD25-P39
24 1 SEAL KIT, TWSD11 BODY 38 2 SCREW, TWSD25
TWSD11-P24 TWSD25-P40
25 1 SEAL KIT, TWSD11 BODY 39 2 PIN, TWSD25
TWSD11-P24 TWLC8-P27
26 1 SEAL KIT, TWSD11 BODY 40 1 CLIP, TWSD25
TWLC8-P15 TWSD25-P42
27 1 SEAL KIT, TWSD11 BODY 41 1 CLIP, TWLC8
TWLC8-P15 TWSD11-P43
28 1 SEAL KIT, TWLC8 MULTI-SWIVEL 42 2 CLIP, TWSD25
TWLC8-P15 TWLC2-P28
29 2 SEAL KIT, TWLC8 MULTI-SWIVEL 43 2 SCREW, TWSD11
TWLC8-P15 TWLC2-P29
30 3 SEAL KIT, TWLC8 MULTI-SWIVEL 44 1 ADAPTOR, TWLC2
TWL8-060-P05 TWLC2-P30
31 4 SEAL KIT, TWLC8 MULTI-SWIVEL 45 1 COUPLING, TWLC2 MALE
TWLC8-P23 TWSD25-P47
32 2 SPRING, TWL8-060 46 1 COUPLING, TWLC2 FEMALE
TWLC2-P23 1000323
33 2 PLUG, TWLC8 47 2 JOURNAL, TWSD25 SIDE PLATE
TWSD6-P35 1000079
34 4 SCREW, TWLC2 48 1 DECAL, TW C.O.O
TWSD6-P36 1000082
35 1 SCREW, TWSD6 49 1 DECAL, TORQUE WRENCH WARNING
TWLC2-P25 1000083
36 1 SCREW, TWSD6 50 1 DECAL, TORQUE WRENCH WARNING
TWSD6-P38 251057
37 1 SCREW, TWLC2 51 1 DECAL, TORQUE WRENCH WARNING
TWSD11-P39
38 2 SCREW, TWSD6 52 1 DECAL, WARNING”
TWSD11-P40
39 2 PIN, TWSD11
TWLC8-P27
40 1 CLIP, TWSD11
TWSD11-P42
41 1 CLIP, TWLC8
TWSD11-P43
42 2 CLIP, TWSD11
TWLC2-P28
43 2 SCREW, TWSD11
TWLC2-P29
44 1 ADAPTOR, TWLC2
TWLC2-P30
45 1 COUPLING, TWLC2 MALE
TWSD11-P47
46 1 COUPLING, TWLC2 FEMALE
1000323
47 2 JOURNAL, TWSD11 SIDE PLATE
1000079
48 1 DECAL, TW C.O.O
1000082
49 1 DECAL, TORQUE WRENCH WARNING
1000083
50 1 DECAL, TORQUE WRENCH WARNING
251057
51 1 DECAL, TORQUE WRENCH WARNING
52 1 DECAL, WARNING
Sheet No. 15 of 15