Vous êtes sur la page 1sur 4

SPILL-EX skirtboard sealing system

A frequently heard complaint regarding bulk transport


on conveyor belts is that spillage and/or dust causes a
great deal of nuisance. Therefor, the conveyor belt
sealing is a crucial component of the installation. A
well-known solution is to use lateral rubber strips as
sealers. However, these strips only produce marginal
improvements, as the strip could not be adjusted to
De voordelen
SPILL-EX
op een The
rij:
match
the vanbelt
profile.
current stringent
requirements in the areas of safety and the
environment, and the need for more efficient
production mean that this type of sealing is no longer
sufficient.
The SPILL-EX sealing system does away with these
disadvantages. It is very durable, easy to adjust,
simple to install and easy to maintain.
Elimination of spillage and dust at transfer points.
The SPILL-EX skirtboard sealing system
A CURE-ALL SOLUTION!
The advantages of SPILL-EX point by point:

Easy and fast installation.

The rubber block, soft yet solid contact with the belt creates a perfect seal.

The blocks can be quickly and easily adjusted.

The blocks are easy to replace without having to remove the other blocks.

The soft yet wear-resistant blocks do not cut into the belt, considerable increasing its life span.

The special wear-resistant rubber guarantees an extremely long life span.

SPILL-EX BS
Max. required height 97 mm
Wear edge 30 mm
The sealing blocks are available to the
following specifications (executions):
Type BSR-NT, rubber sealing block
without chamfer, which can be used
up to 65o C
Type BSR-HT, rubber sealing block
without chamfer, which can be used
up to 150o C
Type BSS-NT, rubber sealing block
with 30o chamfer, which can be used
up to 65o C
Type BSS-HT, rubber sealing block
with 30o chamfer, which can be used
up to 150o C

SPILL-EX HDS
Max. required height 200 mm
Wear edge 70 mm
The sealing blocks are available to the
following specifications (executions:)
Type HDS-NT, rubber sealing block
which can be used up to 65o C
Type HDS-HT, rubber sealing block
which can be used up to 150o C
Type HDS-NTW, white rubber sealing
which can be used up to 65o C
Type HDS-NTA, anti-static and fireretardant rubber sealing block which
can be used up to 150o C

SPILL-EX LPS
Max. required height 150 mm
Wear edge 45 mm
The sealing blocks are available to the
following specifications (executions:)
Type LPS-NT, rubber sealing block
which can be used up to 65o C
Type LPS-HT, rubber sealing block
which can be used up to 150o C
Type LPS-NTW, white rubber sealing
which can be used up to 65o C
Type LPS-NTA, anti-static and fireretardant rubber sealing block which
can be used up to 150o C

SPILL-EX HDR
For sealing the back side of the chute
Wear edge 70 mm
The sealing blocks are available to the
following specifications (executions:)
Type HDR-NT, rubber sealing block
which can be used up to 65o C
Type HDR-HT, rubber sealing block
which can be used up to 150o C
Type HDS-NTW, white rubber sealing
which can be used up to 65o C
Type HDR-NTA, anti-static and fireretardant rubber sealing block which can
be used up to 150o C

TBK europe is member of TBK group

TBK europe BV
Stationsweg Oost 281 C1
3931 ER WOUDENBERG
Tel.:+31 33 2858404
Fax:+31 33 2863991
E-mail: info@tbkbv.com
Website: http: //www.tbkbv.com

Vous aimerez peut-être aussi