Académique Documents
Professionnel Documents
Culture Documents
V200R001C00
Hardware Description
Issue
05
Date
2012-12-12
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and the
customer. All or part of the products, services and features described in this document may not be within the
purchase scope or the usage scope. Unless otherwise specified in the contract, all statements, information,
and recommendations in this document are provided "AS IS" without warranties, guarantees or representations
of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website:
http://www.huawei.com
Email:
support@huawei.com
Issue 05 (2012-12-12)
Commissioning engineers
Symbol Conventions
The symbols that may be found in this document are defined as follows.
Symbol
Description
DANGER
WARNING
CAUTION
Issue 05 (2012-12-12)
TIP
NOTE
ii
Change History
Updates between document issues are cumulative. Therefore, the latest document issue contains
all updates made in previous issues.
Issue 05 (2012-12-12)
iii
Contents
Contents
About This Document.....................................................................................................................ii
1 Cabinets...........................................................................................................................................1
1.1 Introduction to the N66E Cabinet.......................................................................................................................2
1.1.1 Appearance of the N66E Cabinet..............................................................................................................2
1.1.2 Technical Specifications of the N66E Cabinet..........................................................................................2
1.1.3 Components of the N66E Cabinet.............................................................................................................3
1.1.4 Operating Environment of the N66E Cabinet...........................................................................................4
1.1.5 Structural Features of the N66E Cabinet...................................................................................................5
1.2 Introduction to the N68E Cabinet.......................................................................................................................8
1.2.1 Appearance of the N68E cabinet ..............................................................................................................8
1.2.2 Technical Specifications of the N68E cabinet...........................................................................................9
1.2.3 Components of the N68E cabinet............................................................................................................10
1.2.4 Operating Environment of the N68E cabinet..........................................................................................10
1.2.5 Structural Features of the N68E cabinet..................................................................................................11
2 Chassis...........................................................................................................................................15
2.1 Introduction......................................................................................................................................................16
2.2 Hardware Structure...........................................................................................................................................16
2.2.1 S9312.......................................................................................................................................................17
2.2.2 S9306.......................................................................................................................................................20
2.2.3 S9303.......................................................................................................................................................23
2.2.4 S9312E.....................................................................................................................................................24
2.2.5 S9306E.....................................................................................................................................................28
2.2.6 S9303E.....................................................................................................................................................30
2.3 System Configuration and Physical Specifications..........................................................................................32
2.3.1 System Configuration..............................................................................................................................32
2.3.2 Physical Specifications............................................................................................................................34
3 Power Supply...............................................................................................................................37
3.1 Introduction......................................................................................................................................................38
3.1.1 Configuration and Operation Modes of Power Supplies.........................................................................38
3.1.2 Power Supply Principle...........................................................................................................................47
3.2 1600 W DC Power Supply...............................................................................................................................51
3.2.1 Function Overview..................................................................................................................................51
Issue 05 (2012-12-12)
iv
Contents
5 Boards............................................................................................................................................72
5.1 Introduction......................................................................................................................................................76
5.1.1 Board Classification................................................................................................................................76
5.1.2 Slot Distribution and Board Dimensions.................................................................................................80
5.1.3 Relation Between Boards........................................................................................................................83
5.1.4 Interfaces on the Boards..........................................................................................................................85
5.2 SRU-Main Control Unit...................................................................................................................................87
5.2.1 Introduction.............................................................................................................................................87
5.2.2 Function and Application........................................................................................................................88
5.2.3 Panel........................................................................................................................................................89
5.2.4 Interfaces.................................................................................................................................................91
5.2.5 Interface Attributes..................................................................................................................................91
5.2.6 Technical Specifications..........................................................................................................................93
5.3 MCUA-Main Control Unit...............................................................................................................................93
5.3.1 Introduction.............................................................................................................................................93
Issue 05 (2012-12-12)
Contents
vi
Contents
vii
Contents
viii
Contents
5.21.4 Interfaces.............................................................................................................................................168
5.21.5 Interface Attributes..............................................................................................................................169
5.21.6 Technical Specifications......................................................................................................................174
5.22 T24XA - 24-Port 10/100/1000BASE-T and 2-Port 10GBASE-X Interface Card(EA,RJ45/XFP)..............175
5.22.1 Introduction.........................................................................................................................................175
5.22.2 Function and Application....................................................................................................................175
5.22.3 Panel....................................................................................................................................................175
5.22.4 Interfaces.............................................................................................................................................176
5.22.5 Interface Attributes..............................................................................................................................177
5.22.6 Technical Specifications......................................................................................................................179
5.23 G24S - 24-Port 100/1000BASE-X Interface Card (SFP).............................................................................180
5.23.1 Introduction.........................................................................................................................................180
5.23.2 Function and Application....................................................................................................................180
5.23.3 Panel....................................................................................................................................................181
5.23.4 Interfaces.............................................................................................................................................182
5.23.5 Interface Attributes..............................................................................................................................182
5.23.6 Technical Specifications......................................................................................................................185
5.24 G24TFA-24-Port 10/100/1000BASE-T Interface Card(FA,RJ45)..............................................................185
5.24.1 Introduction.........................................................................................................................................185
5.24.2 Function and Application....................................................................................................................185
5.24.3 Panel....................................................................................................................................................186
5.24.4 Interfaces.............................................................................................................................................187
5.24.5 Interface Attributes..............................................................................................................................187
5.24.6 Technical Specifications......................................................................................................................187
5.25 X12SA - 12-Port 10GE Optical Interface Card (SA, SFP+)........................................................................188
5.25.1 Introduction.........................................................................................................................................188
5.25.2 Function and Application....................................................................................................................188
5.25.3 Panel....................................................................................................................................................188
5.25.4 Interfaces.............................................................................................................................................189
5.25.5 Interface Attributes..............................................................................................................................190
5.25.6 Technical Specifications......................................................................................................................191
5.26 X4UX - 4-Port 10GBASE-X Interface Card (XFP).....................................................................................191
5.26.1 Introduction.........................................................................................................................................191
5.26.2 Function and Application....................................................................................................................192
5.26.3 Panel....................................................................................................................................................192
5.26.4 Interfaces.............................................................................................................................................193
5.26.5 Interface Attributes..............................................................................................................................193
5.26.6 Technical Specifications......................................................................................................................195
5.27 X2UX - 2-Port 10GBASE-X Interface Card (XFP).....................................................................................196
5.27.1 Introduction.........................................................................................................................................196
5.27.2 Function and Application....................................................................................................................196
5.27.3 Panel....................................................................................................................................................196
Issue 05 (2012-12-12)
ix
Contents
5.27.4 Interfaces.............................................................................................................................................197
5.27.5 Interface Attributes..............................................................................................................................198
5.27.6 Technical Specifications......................................................................................................................200
5.28 LE2D2X08SED0/LE2D2X08SED1-8-Port 10GE Optical Interface Line Card (ED, SFP+)......................200
5.28.1 Introduction.........................................................................................................................................200
5.28.2 Function and Application....................................................................................................................201
5.28.3 Panel....................................................................................................................................................201
5.28.4 Interfaces.............................................................................................................................................202
5.28.5 Interface Attributes..............................................................................................................................202
5.28.6 Technical Specifications......................................................................................................................204
5.29 WMNPA-WAN Card...................................................................................................................................205
5.29.1 Introduction.........................................................................................................................................205
5.29.2 Function and Application....................................................................................................................206
5.29.3 Panel....................................................................................................................................................206
5.29.4 Technical Specifications......................................................................................................................207
5.30 P4CF-4-Port OC-3c/STM-1c POS-SFP.......................................................................................................208
5.30.1 Introduction.........................................................................................................................................208
5.30.2 Function and Application....................................................................................................................208
5.30.3 Panel....................................................................................................................................................208
5.30.4 Interfaces.............................................................................................................................................209
5.30.5 Interface Attributes..............................................................................................................................210
5.30.6 Technical Specifications......................................................................................................................211
5.31 P4HF-4-Port OC-12c/STM-4c POS-SFP.....................................................................................................211
5.31.1 Introduction.........................................................................................................................................211
5.31.2 Function and Application....................................................................................................................211
5.31.3 Panel....................................................................................................................................................212
5.31.4 Interfaces.............................................................................................................................................213
5.31.5 Interface Attributes..............................................................................................................................213
5.31.6 Technical Specifications......................................................................................................................214
5.32 P1UF-1-Port OC-48c/STM-16c POS-SFP...................................................................................................215
5.32.1 Introduction.........................................................................................................................................215
5.32.2 Function and Application....................................................................................................................215
5.32.3 Panel....................................................................................................................................................216
5.32.4 Interfaces.............................................................................................................................................216
5.32.5 Interface Attributes..............................................................................................................................217
5.32.6 Technical Specifications......................................................................................................................218
6 Cables...........................................................................................................................................219
6.1 DC Power Cable.............................................................................................................................................220
6.1.1 Introduction...........................................................................................................................................220
6.1.2 Structure.................................................................................................................................................220
6.1.3 Technical Specifications........................................................................................................................221
6.2 AC Power Cable.............................................................................................................................................224
Issue 05 (2012-12-12)
Contents
6.2.1 Introduction...........................................................................................................................................224
6.2.2 Structure.................................................................................................................................................224
6.2.3 Technical Specifications........................................................................................................................225
6.3 Ground Cable..................................................................................................................................................226
6.3.1 Introduction...........................................................................................................................................226
6.3.2 Structure.................................................................................................................................................226
6.3.3 Technical Specifications of the Ground Cables.....................................................................................226
6.4 Console Cable.................................................................................................................................................226
6.4.1 Introduction...........................................................................................................................................226
6.4.2 Structure.................................................................................................................................................226
6.4.3 Technical Specifications........................................................................................................................227
6.5 Ethernet Cable................................................................................................................................................228
6.5.1 Introduction...........................................................................................................................................228
6.5.2 Structure.................................................................................................................................................228
6.5.3 Technical Specifications........................................................................................................................230
6.6 Optical Fiber...................................................................................................................................................230
6.6.1 Introduction...........................................................................................................................................231
6.6.2 Optical Connector..................................................................................................................................232
6.6.3 Technical Specifications........................................................................................................................232
6.7 Clock Cable....................................................................................................................................................233
6.7.1 Introduction...........................................................................................................................................233
6.7.2 Structure.................................................................................................................................................234
6.7.3 Technical Specifications........................................................................................................................235
6.8 Stack Cables...................................................................................................................................................237
6.8.1 Introduction...........................................................................................................................................237
6.8.2 Structure.................................................................................................................................................237
6.8.3 Technical Specifications........................................................................................................................237
7 List of Indicators........................................................................................................................239
7.1 Fan Module Indicators....................................................................................................................................240
7.2 Power Supply Indicators.................................................................................................................................240
7.3 SRU Indicators...............................................................................................................................................242
7.4 MCUA Indicators...........................................................................................................................................242
7.5 LPU Indicators................................................................................................................................................243
7.6 CMU Indicators..............................................................................................................................................245
8 List of Boards..............................................................................................................................246
8.1 Boards Supported by the S9300&S9300E......................................................................................................247
8.2 Power Consumption and Weight....................................................................................................................254
xi
Contents
Issue 05 (2012-12-12)
xii
1 Cabinets
Cabinets
l S9300&S9300EThe N68E and N66E cabinets are standard configurations. The cabinets facilitate
maintenance and capacity expansion. In addition, two switches can be located in a cabinet side by side.
l In this document, the cabinets as shown in Figure of Combined N66E cabinets and Figure of
Combined N68E cabinets are not equipped with side panels. When combining two cabinets, you must
install side panels on the cabinets. Otherwise, heat dissipation of the S9300&S9300E is affected.
Issue 05 (2012-12-12)
1 Cabinets
1 Cabinets
Maximum
Installation Height
Inside the Cabinet
Dimensions (W x D x H)
Weight of
an Empty
Cabinet
N66E
46 U
73 kg 1 kg
NOTE
l 1 U = 1.75 in. or 44.45 mm. and U is the height unit defined in the IEC 60297 standard.
l The weight of an empty cabinet consists of the weight of the front door, rear door, and side panels.
Issue 05 (2012-12-12)
1 Cabinets
(2) Rack
Issue 05 (2012-12-12)
Ambient Temperature
Relative Humidity
-25C to +55C
5% to 100% RH
1 Cabinets
NOTE
The temperature and humidity of the equipment room refers to the values measured 1.5 m above the ground
and 0.4 m in front of the equipment.
Cabinet Material
The surface of the cabinet and the rack is purplish grey.
The N66E cabinet is made of welded electro-galvanized steel sheets and cold-rolled steel sheets.
The fireproof performance of the internal materials complies with the Underwriter Laboratories
(UL) standards.
Cabling Mode
Cable apertures are reserved on the top and at the bottom of the N66E cabinet, so that the N66E
cabinet supports overhead cabling and underfloor cabling:
l
In the overhead cabling mode, external cables enter the cabinet through the top of the
cabinet. Figure 1-3 shows the cable apertures.
In the underfloor cabling mode, external cables enter the cabinet through the bottom of the
cabinet.
NOTE
52mm
Network
cable/fiber
Network
cable/fiber
175mm22mm
Reserved holes
500mm
Power cable
500mm
Front Door
Issue 05 (2012-12-12)
1 Cabinets
Heat Dissipation
The front door, rear door, and top plate of the N66E cabinet have high-density air vents.
Therefore, the cabinet supports front air intake, rear air exhaust, and upper air exhaust and
provides good heat dissipation performance.
NOTE
l The S9300&S9300E adopts an air channel from the left to the rear side of the equipment for heat
dissipation.
l The airflow of S9300&S9300E in the cabinet is: front of the cabinet -> left side of the equipment ->
inside the equipment -> rear of the equipment -> rear of the cabinet, as shown in Figure 1-4. This
ensures good heat dissipation.
Issue 05 (2012-12-12)
1 Cabinets
Protective Performance
The protection performance of the N66E cabinet is described as follows:
l
The cabinet design takes full account of electromagnetic compatibility (EMC). Therefore,
the N66E cabinet has excellent electromagnetic shielding performance.
The air vents on the bottom plate of the cabinet are installed with air filters, which enhance
the dust-proof capability of the N66E cabinet.
The grounding resistance of the N66E cabinet is equal to or lower than 0.1 ohm.
ESD Jack
When wear an ESD wrist strap, ensure that the connector of the wrist strap is connected properly
to the ESD jack in the middle of the N66E cabinet, as shown in Figure 1-5.
Figure 1-5 ESD jack on the N66E cabinet
Installation Scenarios
The installation scenarios of the N66E cabinet are as follows:
l
The cabinet can also be installed on the antistatic floor. In this case, the N6X series supports
are required.
Cabinet Combination
The N66E cabinets can be installed side by side. When installing the cabinets side by side,
connect them by using connecting plates, as shown in Figure 1-6.
Issue 05 (2012-12-12)
1 Cabinets
Issue 05 (2012-12-12)
1 Cabinets
Maximum
Installation
Height
Inside the
Cabinet
Dimension (W x D x H)
Weight of an Empty
Cabinet
N68E
46U
100kg
Issue 05 (2012-12-12)
1 Cabinets
NOTE
l 1 U = 1.75 in. or 44.45 mm. U is the height unit defined in the IEC 60297 standard.
l The weight of an empty cabinet includes the weight of the front door, rear door, left side panel, and
right side panel.
4
2
1
1 Front door
3
2 Rear door
3 Side panels
4 Rack
10
1 Cabinets
Table 1-4 Requirements for the operating environment of the N68E cabinet
Ambient Temperature
Relative Humidity
NOTE
l The temperature and humidity of the equipment room refers to the values measured 1.5 m above the
ground and 0.4 m in front of the equipment.
l The short term means that the operating time does not exceed 48 hours continuously or 15 days a year.
Cabinet Material
The N68E cabinet is a cabinet with electro-galvanized steel sheets and cold-rolled steel sheets
assembled by screws. The fireproof performance of internal materials complies with the
standards of the Underwriter Laboratories (UL).
Cabling Mode
Cable apertures are reserved on the top and at the bottom of the N68E cabinet, so that the N68E
cabinet supports overhead cabling and underfloor cabling:
l
In the overhead cabling mode, external cables enter the cabinet through the top of the
cabinet. Figure 1-9 shows the cable apertures.
In the underfloor cabling mode, external cables enter the cabinet through the bottom of the
cabinet.
NOTE
Issue 05 (2012-12-12)
11
1 Cabinets
52mm
Network
cable/fiber
Network
cable/fiber
312mm
312mm
130mm15mm
130mm15mm
312mm
312mm
145mm65mm
Power cable
145mm65mm
Reserved holes
Front Door
ESD Jack
Before installing the N68E cabinet, you must wear an ESD wrist strap and ensure that the
connector of the ESD wrist strap is connected properly to the ESD jack in the middle of the
N68E cabinet, as shown in Figure 1-10.
Figure 1-10 ESD jack in the middle of the N68E cabinet
Issue 05 (2012-12-12)
12
1 Cabinets
Heat Dissipation
The front door, rear door, and bottom plate of the N68E cabinet have high-density air vents.
Therefore, the N68E cabinet supports front air intake, back air exhaust, and upper air exhaust
and provides good heat dissipation performance.
NOTE
l The S9300&S9300E adopts an air channel from the left to the rear side of the equipment for heat
dissipation.
l The airflow of S9300&S9300E in the cabinet is: front of the cabinet -> left side of the equipment ->
inside the equipment -> rear of the equipment -> rear of the cabinet, as shown in Figure 1-11. This
ensures good heat dissipation.
Issue 05 (2012-12-12)
13
1 Cabinets
Protection Performance
The protection performance of the N68E cabinet is described as follows:
l
The cabinet design takes full account of electromagnetic compatibility (EMC). Therefore,
the N68E cabinet has excellent electromagnetic shielding performance.
The air vents on the bottom plate of the cabinet are installed with air filters. The same
enhances the dust-proof capability of the N68E cabinet.
The grounding resistance of the N68E cabinet does not exceed 0.1 ohm.
Installation Scenarios
The installation scenarios of the N68E cabinet are as follows:
l
The N68E cabinet can also be installed on the antistatic floor. In such a case, the N6X series
supports are required.
Cabinet Combination
The N68E cabinets can be installed side by side. When installing the N68E cabinets side by side,
connect them by using connecting plates, as shown in Figure 1-12.
Figure 1-12 Combined N68E cabinets
Issue 05 (2012-12-12)
14
2 Chassis
Chassis
Issue 05 (2012-12-12)
15
2 Chassis
2.1 Introduction
This section describes the characteristics of the S9300&S9300E.
Position
The S9300&S9300E is a high-end Ethernet switch with a large capacity and high performance.
It functions as an access switch or aggregation switch on a metropolitan area network (MAN)
or a core switch on an enterprise network, providing fast Ethernet (FE), gigabit Ethernet (GE),
and 10GE interfaces.
Models
The following models of S9300&S9300E products are available:
l
S9303 switch (S9303 for short): supports double main control units (MCUs), three line
processing units (LPUs), and AC or DC power supplies in 1+1 backup mode.
S9306 switch (S9306 for short): supports double switching and routing units (SRUs), six
LPUs, and DC power supplies in 1+1 backup mode or AC power supplies in 1+1 or 2+2
backup mode.
S9312 switch (S9312 for short): supports double SRUs, 12 LPUs, and DC power supplies
in 1+1 backup mode, or AC power supplies in 1+1 or 2+2 backup mode.
S9303E switch (S9303E for short): supports double MCUs, three LPUs, and AC or DC
power supplies in M+N backup mode (M + N 2).
S9306E switch (S9306E for short): supports double SRUs, six LPUs, and AC or DC power
supplies in M+N backup mode (M + N 4).
S9312E switch (S9312E for short): supports double SRUs, 12 LPUs, and AC or DC power
supplies in M+N backup mode (M + N 6).
NOTE
Power supplies work in M+N backup mode. M indicates the number of active power supplies, and N
indicates the number of backup power supplies. The power supply requirement is: M x Output power of
one power supply > Total power consumption of the equipment. N must be greater than zero.
The S9300 series switches have different capacities and structures but they use the same software
platform, hardware platform, LPUs, and software. The S9303E, S9306E, and S9312E have
different capacities and structures but they use the same software platform, hardware platform,
LPUs, and software. Two types of main processing units (MPUs) are available:
l
MCU: used by the S9303&S9303E and integrates the functions of the centralized
monitoring unit (CMU) on the S9306&S9306E and S9312&S9312E.
The S9300E can use a common chassis or a chassis that has gained the FCC certificate. Customers can
choose an appropriate chassis when purchasing the switch.
16
2 Chassis
2.2.1 S9312
The S9312 is 15 U (1 U = 44.45 mm) high. When the chassis has no cable divider installed, the
dimensions are 442 mm x 476 mm x 663.95 mm (W x D x H). When the chassis has cable
dividers installed, the dimensions are 442 mm x 585 mm x 663.95 mm (W x D x H). Figure
2-1 and Figure 2-2 show the appearance and components of the S9312. Figure 2-3 shows the
layout of slots on the S9312.
Figure 2-1 Appearance and components of the S9312 (1)
1. LPU
2. SRU
3. Rack-mounting ear
4. Cable divider
6. CMU
7. Power supply
Issue 05 (2012-12-12)
17
2 Chassis
1. Air filter
Issue 05 (2012-12-12)
2. Fan
18
2 Chassis
PoE
PoE
PoE
PoE
CMU1
CMU2
PWR4
PWR3
PWR2
PWR1
SLOT1-LPU
The S9312 uses an integrated chassis of which the main components are described in Table
2-1.
Table 2-1 Components of the S9312
Issue 05 (2012-12-12)
Component
Description
Reference
SRU
LPU
See 5 Boards.
CMU
19
2 Chassis
Component
Description
Reference
Fan module
Power supply
See 3 Power
Supply.
Cable divider
Cable
See 6 Cables.
NOTE
Only AC power supplies can be installed in PoE power slots. On an S9300, the 2200 W AC power supply
can only be installed in the PoE slot.
l When an AC power supply is inserted into the PoE power slot, it is used as a PoE power supply, and
provides power for powered devices (PDs) by using the Ethernet PoE electrical interface board.
l When an AC power supply is inserted into slots PWR1 to PWR4, it provides power for the entire device.
l The S9312 has PoE chassis and non-PoE chassis, which are identified by the nameplates and silkscreens
on power slots.
2.2.2 S9306
The S9306 is 10 U (1 U = 44.45 mm) high. When the chassis has no cable divider installed, the
dimensions are 442 mm x 476 mm x 441.7 mm (W x D x H). When the chassis has cable dividers
installed, the dimensions are 442 mm x 585 mm x 441.7 mm (W x D x H). Figure 2-4 and
Figure 2-5 show the appearance and components of the S9306. Figure 2-6 shows the layout of
slots on the S9306.
Issue 05 (2012-12-12)
20
2 Chassis
1. LPU
2. SRU
3. Rack-mounting ear
4. Cable divider
6. CMU
7. Power supply
1. Air filter
Issue 05 (2012-12-12)
2. Fan
21
2 Chassis
PoE
PoE
PoE
PoE
CMU1
CMU2
PWR4
PWR3
PWR2
PWR1
SLOT1-LPU
The S9306 uses an integrated chassis of which the main components are described in Table
2-2.
Table 2-2 Components of the S9306
Issue 05 (2012-12-12)
Component
Description
Reference
SRU
LPU
See 5 Boards.
CMU
Fan module
Power supply
See 3 Power
Supply.
Cable divider
Cable
See 6 Cables.
22
2 Chassis
NOTE
l Only AC power supplies can be installed in PoE power slots. On an S9300, the 2200 W AC power
supply can only be installed in the PoE slot.
l When an AC power supply is inserted into the PoE power slot, it is used as a PoE power supply, and
provides power for powered devices (PDs) by using the Ethernet PoE electrical interface board.
l When an AC power supply is inserted into slots PWR1 to PWR4, it provides power for the entire device.
l The S9306 has PoE chassis and non-PoE chassis, which are identified by the nameplates and silkscreens
on power slots.
2.2.3 S9303
The S9303 is 4 U (1 U = 44.45 mm) high. When the chassis has no cable divider installed, the
dimensions are 442 mm x 476 mm x 175 mm (W x D x H). When the chassis has cable dividers
installed, the dimensions are 442 mm x 585 mm x 175 mm (W x D x H). Figure 2-7 and Figure
2-8 show the appearance and components of the S9303. Figure 2-9 shows the layout of slots on
the S9303.
Figure 2-7 Appearance and components of the S9303 (1)
1. Rack-mounting ear
2. Power supply
3. MCU
4. LPU
6. Cable divider
1. Fan
Issue 05 (2012-12-12)
2. Air filter
23
2 Chassis
SLOT5-MCU
PWR2
PoE
The S9303 uses an integrated chassis of which the main components are described in Table
2-3.
Table 2-3 Components of the S9303
Component
Description
Reference
MCU
LPU
See 5 Boards.
Fan module
Power supply
See 3 Power
Supply.
Cable divider
Cable
See 6 Cables.
NOTE
l Only AC power supplies can be installed in PoE power slots. On an S9300, the 2200 W AC power
supply can only be installed in the PoE slot.
l When an AC power supply is inserted into the PoE power slot, it is used as a PoE power supply, and
provides power for powered devices (PDs) by using the Ethernet PoE electrical interface board.
l When an AC power supply is inserted into slots PWR1 to PWR2, it provides power for the entire device.
2.2.4 S9312E
Issue 05 (2012-12-12)
24
2 Chassis
The S9312E is 15 U high.When the chassis has no cable divider installed, the dimensions are
442 mm x 476 mm x 663.95 mm (W x D x H). When the chassis has cable dividers installed,
the dimensions are 442 mm x 585 mm x 663.95 mm (W x D x H). Figure 2-10 and Figure
2-11 show the appearance and components of the S9312E. Figure 2-12 shows the layout of slots
on the S9312E.
Figure 2-10 Appearance and components of the S9312E (1)
1. LPU
2. SRU
3. Rack-mounting ear
4. Cable divider
5. CMU
Issue 05 (2012-12-12)
25
2 Chassis
1. Air filter
Issue 05 (2012-12-12)
2. Fans
26
2 Chassis
PWR6
PWR5
CMU1
CMU2
PWR4
PWR3
PWR2
PWR1
SLOT1-LPU
The S9312E uses an integrated chassis. Table 2-4 describes the main components.
Table 2-4 Components of the S9312E
Issue 05 (2012-12-12)
Component
Name
Introduction
Description
SRU
LPU
CMU
Fan module
27
2 Chassis
Component
Name
Introduction
Description
PWR
Cable divider
Cable
2.2.5 S9306E
The S9306E is 10 U high. When the chassis has no cable divider installed, the dimensions are
442 mm x 476 mm x 441.7 mm (W x D x H). When the chassis has cable dividers installed, the
dimensions are 442 mm x 585 mm x 441.7 mm (W x D x H). Figure 2-13 and Figure 2-14 show
the appearance and components of the S9306E. Figure 2-15 shows the layout of slots on the
S9306E.
Figure 2-13 Appearance and components of the S9306E (1)
1. LPU
2. SRU
3. Rack-mounting ear
4. Cable divider
5. CMU
Issue 05 (2012-12-12)
28
2 Chassis
1. Air filter
2. Fans
CMU1
CMU2
PWR4
PWR3
PWR2
PWR1
SLOT1-LPU
The S9306E uses an integrated chassis. Table 2-5 describes the main components.
Issue 05 (2012-12-12)
29
2 Chassis
Introduction
Description
SRU
LPU
CMU
Fan module
PWR
Cable divider
Cable
2.2.6 S9303E
The S9303E is 4 U high. When the chassis has no cable divider installed, the dimensions are
442 mm x 476 mm x 175 mm (W x D x H). When the chassis has cable dividers installed, the
dimensions are 442 mm x 585 mm x 175 mm (W x D x H). Figure 2-16 and Figure 2-17 show
the appearance and components of the S9303E. Figure 2-18 shows the layout of slots on the
S9303E.
Figure 2-16 Appearance and components of the S9303E (1)
5
1
1. Rack-mounting ear
Issue 05 (2012-12-12)
2 3
4
2. Power module
3. MCU
30
2 Chassis
4. LPU
5. Cable divider
1. Fan
2. Air filters
SLOT5-MCU
PWR2
The S9303E uses an integrated chassis. Table 2-6 describes the main components.
Table 2-6 Components of the S9303E
Issue 05 (2012-12-12)
Component
Name
Introduction
Description
MCU
LPU
Fan module
31
2 Chassis
Component
Name
Introduction
Description
PWR
Cable divider
Cable
Issue 05 (2012-12-12)
Item
S9312/S9312E
S9306/
S9306E
S9303/
S9303E
Notes
Processor
S9312: 700MHz,
S9312E: 1.2GHz
(Dominant
frequency)
S9306:
700MHz,
S9306E:
1.2GHz
(Dominant
frequency)
500 MHz
(Dominant
frequency)
DDR2
SDRAM
S9312: 1GB,
S9312E: 2GB
S9306: 1GB,
S9306E:
2GB
512 MB
NVRAM
512 KB
512 KB
512 KB
Battery supply
Flash
S9312: 64MB,
S9312E: 128MB
S9306:
64MB,
S9306E:
128MB
64 MB
CF card
512 MB
512 MB
512 MB
32
2 Chassis
Item
S9312/S9312E
S9306/
S9306E
S9303/
S9303E
Notes
Switching
capacity
(bit/s)
S9306: 2T,
S9306E:
3.84T
S9303:
768G,
S9303E:
1.92T
Bidirectional, sum of
switching capacities
of the two MPUs
Backplane
capacity
(bit/s)
S9306: 6T,
S9306E:
14.4T
S9303: 3T,
S9303E:
7.2T
Forwarding
capability
(pps)
S9312: 1344M,
S9312E: 2880M
S9306:
1152M,
S9306E:
2880M
S9303:
576M,
S9303E:
1440M
Number of
LPU slots
12
LPU (Optional)
Number of
SRU/MCU
slots
S9306/S9306E/
S9312/S9312E: SRU
Max
transmissio
n rate of an
LPU port
48GE, 4010GE
S9303/S9303E: full
mesh
48GE,
4010GE
48GE,
4010GE
Issue 05 (2012-12-12)
33
2 Chassis
entire device can provide a maximum of 576 GE interfaces. That is, the interface density
is 576. The transmission rate of each GE interface is 1 Gbit/s; therefore, the interface
capacity of the S9312 is 576 Gbit/s.
S9312/S9312E
S9306/S9306E
S9303/S9303E
Dimensions
(W x D x H,
excluding the
rack-mounting
ears)
442 mm x 476 mm x
663.95 mm (15 U high)
442 mm x 476 mm x
441.7 mm (10 U high)
442 mm x 476 mm x
175 mm (4 U high)
Cabinet
N66E or N68E
N66E or N68E
N66E or N68E
Maximum
power (full
configuration)
S9312:3000 W,
S9312E:4400 W
S9306:1600 W,
S9306E:2200 W
S9303:800 W,
S9303E:1100 W
Noise at
normal
temperature
(acoustic
power)
S9312:64.6 dB,
S9312E:69.7 dB
S9306:61.6 dB,
S9306E:67 dB
S9303:58.6 dB,
S9303E:64.5 dB
Weight
(empty/fully
loaded)
DC
input
Rated
voltag
e
-48 V DC/-60 V DC
Maxi
mum
voltag
e
range
NOTE
The heat
dissipation
value of a
device equals
the current
power
consumption of
the device.
Issue 05 (2012-12-12)
l S9300E: 37 kg/70
kg
l S9300E: 29 kg/45
kg
l S9300E: 11 kg/25
kg
34
Item
AC
input
PoE
NOT
E
The
S93
00E
Seri
es
Swi
tche
s do
not
sup
port
PoE
.
Ambi
ent
temp
eratu
re
Humi
dity
Issue 05 (2012-12-12)
2 Chassis
S9312/S9312E
S9306/S9306E
S9303/S9303E
Rated
voltag
e
Rated
voltag
e
range
l S9312: 200 V AC to
240 V AC, 47 Hz to
63 Hz
100 V AC to 120 V AC
and 200 V AC to 240 V
AC, 47 Hz to 63 Hz
100 V AC to 120 V AC
and 200 V AC to 240 V
AC, 47 Hz to 63 Hz
Maxi
mum
voltag
e
range
Power
input
mode
Redun
dancy
mode
of
power
suppli
es
Output
power
consu
mptio
n
8800 W
8800 W
2200 W
Longterm
0C to 45C
Shortterm
-5C to 55C
Storag
e
-40C to 70C
Longterm
Shortterm
l S9312E: 110/220 V
AC, 50/60 Hz
l S9312E: 100 V AC
to 120 V AC and
200 V AC to 240 V
AC, 50/60 Hz
35
Item
Altit
ude
2 Chassis
S9312/S9312E
S9306/S9306E
Storag
e
Longterm
< 3000 m
Storag
e
< 5000 m
S9303/S9303E
NOTE
l The temperature and humidity are measured 1.5 m above the floor and 0.4 m at the front of the cabinet.
There should be no protection board at the front or back of the cabinet.
l Short-term means that the continuous operation time does not exceed 48 hours and the accumulated
time per year does not exceed 15 days.
Issue 05 (2012-12-12)
36
3 Power Supply
Power Supply
Issue 05 (2012-12-12)
37
3 Power Supply
3.1 Introduction
This section provides an overview of AC power supplies and DC power supplies on the
S9300&S9300E.
CAUTION
l Do not install a DC power supply and an AC power supply on the same S9300.
l To use a DC power supply and an AC power supply simultaneously on an S9300E, contact
Huawei technical personnel.
l Ensure that the S9300&S9300E is properly grounded before powering it on.
l Power off the S9300&S9300E before removing a power supply.
l Do not operate power supplies when the switch is running.
l When powering off the S9300&S9300E, shut down all the power supplies of the
S9300&S9300E.
This section describes the configuration of the power supplies that ensure proper operation of the
S9300&S9300E.
S9312
On the S9312, system power supplies are located in slots PWR1 to PWR4. The S9312 supports
both DC and AC power supplies. PWR1 and PWR2 are in area A, and PWR3 and PWR4 are in
area B. Area A and area B work in backup mode, as shown in Figure 3-1. PWR1 and PWR2
work in load balancing mode. PWR3 and PWR4 work in load balancing mode.
A DC power supply and an AC power supply cannot be located in the same area.
Issue 05 (2012-12-12)
38
3 Power Supply
LPU
LPU
LPU
LPU
LPU
LPU
SRU
SRU
LPU
LPU
LPU
LPU
LPU
AreaA
PoE
PoE
PoE
PoE
CMU1
CMU2
PWR3
Slave
PWR4
Filler panel
PWR2
Filler panel
PWR1
Master
LPU
Area B
Issue 05 (2012-12-12)
39
3 Power Supply
A maximum of four PoE power supplies can be installed on an S9312. The PoE power supplies
work in 3+1 or 2+2 backup mode, or do not work in backup mode.
l
The 2200 W AC power supply provides only PoE power, but does not provide power for the entire device.
Currently, the S9312 does not support 2200 W DC power supplies.
Issue 05 (2012-12-12)
40
3 Power Supply
S9312E
On the S9312E, system power supplies are located in slots PWR1 to PWR6. The AC power
supplies and DC power supplies are supported, as shown in Figure 3-2.
To use AC and DC power supplies simultaneously on an S9312E, contact Huawei technical
personnel.
Figure 3-2 Configuration of S9312E power supplies
LPU
LPU
LPU
LPU
LPU
LPU
SRU
SRU
LPU
LPU
LPU
LPU
LPU
LPU
PWR2
PWR3
PWR4
CMU2
CMU1
PWR1
PWR5
PWR6
l
Issue 05 (2012-12-12)
41
3 Power Supply
The maximum power consumption of the S9312E in full configuration is 4400 W. (The
system provides a maximum of 6600 W and the maximum power consumption of switches
of V200R002C00 and earlier versions is 4400 W.) The power supply module supports the
following backup modes:
220 V AC power supplies in 1+1 backup mode (2200 W)
This configuration provides a maximum of 2200 W power. The 2200 W AC power
supplies can be installed in any two of slots PWR1 to PWR6.
220 V AC power supplies in 2+1 backup mode (4400 W)
This configuration provides a maximum of 4400 W power. The 2200 W AC power
supplies can be installed in any three of slots PWR1 to PWR6.
110 V AC power supplies in 2+1 backup mode (2200 W)
This configuration provides a maximum of 2200 W power. The 2200 W AC power
supplies can be installed in any three of slots PWR1 to PWR6.
110 V AC power supplies in 3+1 backup mode (3300 W)
This configuration provides a maximum of 3300 W power. The 2200 W AC power
supplies can be installed in any four of slots PWR1 to PWR6.
NOTE
Currently, the S9312E does not support 1600 W DC power supplies, 800 W AC power supplies, or the
PoE function.
When the input voltage for an S9312E is 110 V, confirm with Huawei technical personnel to determine
the power supply configuration.
S9306
On the S9306, system power supplies are located in slots PWR1 to PWR4. The DC power
supplies and AC power supplies are supported. PWR1 and PWR2 are in area A, and PWR3 and
PWR4 are in area B. Area A and area B work in backup mode, as shown in Figure 3-3. PWR1
and PWR2 work in load balancing mode. PWR3 and PWR4 work in load balancing mode.
A DC power supply and an AC power supply cannot be located in the same area.
Issue 05 (2012-12-12)
42
3 Power Supply
LPU
AreaA
PoE
PoE
PoE
PoE
CMU1
CMU2
SRU
PWR3
Slave
PWR4
Filler panel
PWR2
Filler panel
PWR1
Master
LPU
AreaB
Issue 05 (2012-12-12)
43
3 Power Supply
AC power supplies are installed in PWR2 and PWR3, and the filler panels are
installed in PWR1 and PWR4.
AC power supplies are installed in PWR2 and PWR4, and the filler panels are
installed in PWR1 and PWR3.
AC power supplies are installed in PWR1 and PWR4, and the filler panels are
installed in PWR2 and PWR3.
220 V AC power supplies in 2+2 backup mode (1600 W)
This configuration provides a maximum of 1600 W power. Four AC power supplies
are installed in active area A and standby area B. The AC power supplies are installed
in slots PWR1 to PWR4.
110 V AC power supplies in 2+2 backup mode (800 W)
One 110 V AC power supply provides 400 W power. To meet power requirement of
the S9306, the backup mode must be used for 110 V AC power supplies. The AC power
supplies are installed in the PWR1 to PWR4 slots.
A maximum of four PoE power supplies can be installed on an S9306. The PoE power supplies
work in 3+1 or 2+2 backup mode, or do not work in backup mode.
l
The 2200 W AC power supply provides only PoE power, but does not provide power for the entire device.
Currently, the S9306 does not support 2200 W DC power supplies.
When the input voltage for an S9306 is 110 V, confirm with Huawei technical personnel to determine the
power supply configuration.
S9306E
On the S9306E, system power supplies are located in slots PWR1 to PWR4, as shown in Figure
3-4. The S9306E supports both AC and DC power supplies.
Issue 05 (2012-12-12)
44
3 Power Supply
PWR3
PWR4
CMU2
CMU1
PWR1
Currently, the S9306E does not support 1600 W DC power supplies, 800 W AC power supplies, or the
PoE function.
When the input voltage for an S9306E is 110 V, confirm with Huawei technical personnel to determine
the power supply configuration.
Issue 05 (2012-12-12)
45
3 Power Supply
S9303
On the S9303, system power supplies are located in slots PWR1 to PWR2. The S9303 supports
both DC and AC power supplies. PWR1 is in area A, and PWR2 is in area B. Area A and area
B work in backup mode, as shown in Figure 3-5.
Figure 3-5 Configuration of S9303 power supplies
LPU
LPU
LPU
MCU
PW R1
Master
PWR
MCU
PW R2
Slave PWR
PoE
Only one PoE power supply can be installed on an S9303. The PoE power supplies include:
l
800 W PoE power supplies. When 220 V power source is used, an 800 W power supply
provides a maximum of 800 W power. When 110 V power source is used, an 800 W power
supply provides a maximum of 400 W power.
2200 W PoE power supplies. When 220 V power source is used, a 2200 W power supply
provides a maximum of 2200 W power. When 110 V power source is used, a 2200 W power
supply provides a maximum of 1100 W power.
NOTE
The 2200 W power supply only provides PoE power, but does not provide power for the entire device.
Currently, the S9303 does not support 2200 W DC power supplies.
When the input voltage for an S9303 is 110 V, confirm with Huawei technical personnel to determine the
power supply configuration.
Issue 05 (2012-12-12)
46
3 Power Supply
S9303E
On the S9303E, system power supplies are located in slots PWR1 and PWR2, as shown in
Figure 3-6.
To use AC and DC power supplies simultaneously on an S9303E, contact Huawei technical
personnel.
Figure 3-6 Configuration of S9303E power supplies
LPU
LPU
LPU
MCU
PWR1
MCU
PWR2
Currently, the S9303E does not support 1600 W DC power supplies, 800 W AC power supplies, or the
PoE function.
When the input voltage for an S9303E is 110 V, confirm with Huawei technical personnel to determine
the power supply configuration.
47
3 Power Supply
Figure 3-7 and Figure 3-8 show the principle of the DC power supplies on the
S9300&S9300E. Figure 3-9 and Figure 3-10 show the principle of the AC power supplies.
Figure 3-7 Principle of the DC power supplies on the S9300
Board 2
Board 1
Board n
Backplane
-48V1/-60V1
RTN1
-48V2/-60V2
RTN2
PWR1
PWR2
-48/-60V RTN
-48/-60V RTN
DC
DC
-48V1/-60V1
-48V2/-60V2
RTN1
RTN2
Issue 05 (2012-12-12)
48
3 Power Supply
Board 1
Board 2
Board n
Backplane
-48V
RTN
PWR1
-48/-60V
RTN
-48V
RTN
PWR2
DC
-48/-60V
RTN
DC
-48V
RTN
-48V
PWR3
-48/-60V
RTN
DC
RTN
PWR4
-48/-60V
RTN
DC
-48V
-48V/-60V
RTN
-48 V/-60V: power wire
Issue 05 (2012-12-12)
49
3 Power Supply
Board 1
Board n
Board 2
Backplane
-48VA
RTNA
PWR1
RTNA
PWR2
L N PGND
AC
-48VA
RTNB
-48VB
PWR3
L N PGND
AC
-48VB
PWR4
L N PGND
AC
RTNB
L N PGND
AC
PWR1-PWR2 -48VA
PWR3-PWR4 -48VB
PWR1-PWR2 RTNA
PWR3-PWR4 RTNB
L: live wire
Issue 05 (2012-12-12)
N: neutral wire
50
3 Power Supply
Board 1
Board 2
Backplane
Board n
RTN
RTN
RTN
RTN
-48V
-48V
-48V
-48V
PWR1
PWR2
PWR3
PWR4
L N PGND
L N PGND
AC
L N PGND
AC
L N PGND
AC
AC
-48V
RTN
L: live wire
N: neutral wire
Various alarms, for example, no-input alarm, air breaker off alarm, invalid lightening-proof
alarm, and input undervoltage alarm.
Issue 05 (2012-12-12)
51
3 Power Supply
1
NEG(-) RTN(+)
2
NEG(-) RTN(+)
4
ON
ON
40
O
OFF
OFF
INPUT
ALM
INPUT O
ALM O
1. NEG
2. RTN
4. Handle
5. Indicator
3. Switch
The indicators of the power supplies are shown on the panel through the light pipe. Table 3-1
describes the indicators on a 1600 W DC power supply panel.
Table 3-1 Indicators on a 1600 W DC power supply
Indicator
Color
Description
ALM
Red
Issue 05 (2012-12-12)
52
3 Power Supply
Indicator
Color
Description
INPUT
Green
NOTE
Table 3-2 describes the relationship between 1600 W DC power input cables and terminals.
Table 3-2 Relationship between 1600 W DC power input cables and terminals
Terminal
Identifier
Cable
Cable Color
Connected Terminal
RTN
Power ground
cable
Black
OT crimp terminal
NEG
Power cable
Blue
NOTE
RTN: Return
Specification
Dimensions (W x D x H)
41 mm x 393 mm x 130 mm
-48 V/-60V DC
Output voltage
Issue 05 (2012-12-12)
Output current
40 A
40 A
1600 W
53
3 Power Supply
Output overcurrent
Output overvoltage
Input overvoltage
Input undervoltage
Overtemperature
Short circuit
Surge
54
3 Power Supply
3
4
1. NEG
2. RTN
4. Switch
5. Indicator
3. Handle
The indicators of a 2200 W DC power supply are shown on the panel through the light pipe.
Table 3-4 describes the indicators of the power supplies.
Table 3-4 Indicators on a 2200 W DC power supply panel
Indicator
Color
Description
RUN
Green
ALM
Yellow
FAULT
Red
Issue 05 (2012-12-12)
55
3 Power Supply
NOTE
Table 3-5 describes the relationship between the 2200 W DC power input cables and terminals.
Table 3-5 Relationship between DC power input cables and terminals
Terminal
Cable Name
Cable Color
Interface
RTN
Power ground
cable
Black
NEG
Power cable
Blue
NOTE
RTN: Return
Description
Dimensions (W x D x H)
41 mm x 393 mm x 130 mm
Weight
<6.0 kg
-48 V/-60 V DC
42 A
60 A
56
3 Power Supply
The 220V AC power supply provides 800W power and the 110V power supply provides 400W
power. In addition, the AC power supply supports EMC filtering and provides the following
functions:
l
Output over-current
Output over-voltage
Output under-voltage
Input over-voltage
Input under-voltage
Over-temperature
Short circuit
Surge protection
Issue 05 (2012-12-12)
57
3 Power Supply
ON
RUN
ALM
FAULT
OFF
RUN
ALM
FAULT
1. Power input
2. Handle
3. Switch
4. Indicator
Color
Description
RUN
Green
ALM
Yellow
FAULT
Red
Issue 05 (2012-12-12)
58
3 Power Supply
Specification
Dimensions (W x D x H)
41 mm x 393 mm x 130 mm
Weight
< 2.5 kg
5A
Output overcurrent
Output overvoltage
Output undervoltage
Input overvoltage
Input undervoltage
Overtemperature
Short circuit
Lightning
Issue 05 (2012-12-12)
59
3 Power Supply
ON
RUN
ALM
FAULT
OFF
RUN
ALM
FAULT
1. Power input
2. Handle
3. Switch
4. Indicator
60
3 Power Supply
Color
Description
RUN
Green
Yellow
ALM
Red
FAULT
Issue 05 (2012-12-12)
Item
Specification
Dimensions(W x D x H)
41 mm x 393 mm x 130 mm
Weight
< 6.0 kg
15.5 A
61
Issue 05 (2012-12-12)
62
4.1 Introduction
This section provides an overview of the heat dissipation system of the S9300&S9300E.
Issue 05 (2012-12-12)
63
64
CAUTION
When a fan on the S9300&S9300E is faulty, a trap is reported. If all fans are faulty, shut down
the device.
The S9300&S9300E uses modular fan modules. The S9300 and S9300E use different fan
models. The numbers of fans used by different switch models are different. Installed at the rear
of the chassis, the fan modules are used to cool down the S9300&S9300E. The fan modules are
hot swappable and interchangeable.
Each S9300&S9300E fan module serves a zone in the chassis and uses the intelligent fan-speed
adjustment technology. The fan module monitors the temperature of key components and
controls the temperature in each zone. If a component overheats, the fan speed increases. When
the temperature falls within the allowed range, the fan speed decreases. The fan modules improve
system reliability and reduce power consumption and noise.
SLOT6-LPU
SLOT5-LPU
SLOT4-LPU
SLOT8-SRU
SLOT7-SRU
SLOT3-LPU
SLOT2-LPU
CMU1
CMU2
SLOT1-LPU
As shown in Figure 4-5, the S9312&S9312E have four fan modules, serving four zones. Each
zone contains four boards. The boards in slots 4 and 9 belong to two zones.
Issue 05 (2012-12-12)
65
SLOT12-LPU
SLOT11-LPU
SLOT10-LPU
SLOT9-LPU
SLOT8-LPU
SLOT7-LPU
SLOT14-SRU
SLOT13-SRU
SLOT6-LPU
SLOT5-LPU
SLOT4-LPU
SLOT3-LPU
SLOT2-LPU
CMU1
CMU2
SLOT1-LPU
4.2.2 Panel
The fan module consists of the fan frame, dual fans, and fan control board (FCB).
Figure 4-6 shows the panel of the fan module on an S9300&S9300E.
Issue 05 (2012-12-12)
66
RUN/ALM
RUN/ALM
Color
Description
RUN/ALM
Green
Red
Issue 05 (2012-12-12)
Item
Specification
Dimensions (W x D x H)
Weight
1140 20 g
Maximum power
consumption
31.6 W
319 Pa
163 CFM
67
Item
Specification
Maximum noise
62 dB
Operating voltage
-38.4 V DC to -72 V DC
Table 4-3 shows the technical specifications of the fan modules on the S9300E.
Table 4-3 Technical specifications of the fan module
Item
Specification
Dimensions (W x D x H)
Weight
1540 20 g
Maximum power
consumption
50 W
355 Pa
245 CFM
Maximum noise
70 dB
Operating voltage
-30 V DC to -73 V DC
Issue 05 (2012-12-12)
68
The air filters can be removed. For the method of removing and installing the air filters, see
Precautions for Replacing Air Filters in the S9300&S9300E Terabit Routing Switch Parts
Replacement.
69
the type not supporting FCC standards. Figure 4-9 shows an air filter that does not support FCC
standards, and Figure 4-10 shows an air filter that supports FCC standards.
Figure 4-9 S9306&S9306E air filter not supporting FCC standards
The air filter can be removed. For the method of removing and installing the air filter, see
Precautions for Replacing Air Filters in the S9300&S9300E Terabit Routing Switch Parts
Replacement.
70
On the S9303&S9303E, the air filter is separated from fan trays. Each S9303&S9303E switch
requires one air filter, which is installed from rear of the switch. The S9303E can use two types
of air filters: the type supporting Federal Communications Commission (FCC) standards and
the type not supporting FCC standards. Figure 4-11 shows an air filter that does not support
FCC standards, and Figure 4-12 shows an air filter that supports FCC standards.
Figure 4-11 S9303&S9303E air filter not supporting FCC standards
The air filter can be removed. For the method of removing and installing the air filter, see
Precautions for Replacing Air Filters in the S9300&S9300E Terabit Routing Switch Parts
Replacement.
Issue 05 (2012-12-12)
71
5 Boards
Boards
72
5 Boards
SFP) and 48-Port 100/1000BASE-X Interface Card (FA, SFP), including the appearance,
functions and features, panel, interface attributes, and technical specifications.
5.10 G48SBC-48-Port 100/1000BASE-X Interface Card (BC, SFP)
This section describes the 48-Port 100/1000BASE-X Interface Card (BC, SFP), including the
appearance, functions and features, applicable device, slot, panel, indicators, interfaces, and
technical specifications.
5.11 G48T - 48-Port 10/100/1000BASE-T Interface Card (RJ45)
This section describes the 48-Port 100/1000BASE-T Interface Card (EA, RJ45), 48-Port
10/100/1000BASE-T Interface Card (EC, RJ45) 48-Port 10/100/1000BASE-T Interface Card
(ED, RJ45) and 48-Port 1000BASE-T Interface Card (FA, RJ45), including the appearance,
functions and features, panel, and technical specifications.
5.12 G48TBC-48-Port 10/100/1000BASE-T Interface Card (BC, RJ45)
This section describes the 48-Port 10/100/1000BASE-T Interface Card (BC, RJ45), including
the appearance, functions and features, panel, and technical specifications.
5.13 G48VA - 48-Port 10/100/1000BASE-T PoE Interface Card(EA,RJ45,PoE)
This section describes the 48-Port 10/100/1000BASE-T PoE Interface Card, including the
appearance, functions and features, applicable device, slot, panel, indicators, interfaces, and
technical specifications.
5.14 G48CEAT - 36-Port 10/100/1000BASE-T and 12-Port 100/1000BASE-X Interface Card
(EA, RJ45/SFP)
This section describes the 36-Port 10/100/1000BASE-T and 12-Port 100/1000BASE-X
Interface Card(EA,RJ45/SFP), including the appearance, functions and features, applicable
devices, slots, panel, indicators, interfaces, and technical specifications.
5.15 F48S - 48-Port 100BASE-FX Interface Card (SFP)
This section describes the 48-Port 100BASE-FX Interface Card (EA, SFP) and 48-Port
100BASE-FX Interface Card (EC, SFP), including the appearance, functions and features, panel,
interface attributes, and technical specifications.
5.16 F48T - 48-Port 10/100BASE-T Interface Card (RJ45)
This section describes the 48-Port 10/100BASE-T Interface Card (EA, RJ45), 48-Port
10/100BASE-T Interface Card (EC, RJ45) and 48-Port 10/100BASE-T Interface Card (FA,
RJ45) , including the appearance, functions and features, panel, and technical specifications.
5.17 LE0DX40SFC00/LE2D2X40SFC1-40-Port 10GE Optical Interface Card (FC, SFP+)
This section describes the X40SFC-40-port 10GE optical interface card (FC, SFP+), including
the functions and features, applicable device models and slots, panel, indicators, interface
attributes, and technical specifications.
5.18 LE0DX16SFC00/LE2D2X16SFC1-16-Port 10GE Optical Interface Card (FC, SFP+)
This section describes the X16SFC-16-port 10GE optical interface card (FC, SFP+), including
the functions and features, applicable device models and slots, panel, indicators, interface
attributes, and technical specifications.
5.19 G24CA - 24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Interface Card (SFP/
RJ45)
This section describes the 24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Interface
Card (SA, SFP/RJ45), including the appearance, functions and features, panel, interface
attributes, and technical specifications.
5.20 G24CEAS - 24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Combo Interface
Card(EA,SFP/RJ45, 1588)
This section describes the 24-Port 100/1000BASE-X and 8-Port 10/100/1000BASE-T Combo
Interface Card(EA,SFP/RJ45, 1588), including the appearance, functions and features,
Issue 05 (2012-12-12)
73
5 Boards
Issue 05 (2012-12-12)
74
5 Boards
This section describes the 1-port OC-48c/STM-16c POS-SFP, including the appearance,
functions and features, panel, and technical specifications.
Issue 05 (2012-12-12)
75
5 Boards
5.1 Introduction
This section provides an overview of the boards supported by the S9300&S9300E, including
board classification, slot distribution, relation between boards, board appearances, and interfaces
on each board.
Issue 05 (2012-12-12)
Type
Name
Description
SRU
SRUA
SRUB
MCU
MCUA
CKM
CKMA
CMU
CMUA
SPU
VAMPA
FSU
FSUA
VSU
VSTSA
76
5 Boards
Type
Name
Description
LPU
l G24CA
NOTE
LPUs are classified into S series boards, E series boards, F
series boards, B series boards, and POS boards:
l G24SA
l X12SA
l G48SA
l G48SBC
l G48SC
l G48SD
l G48SFA
l F48SA
l F48SC
l G48TA
l G48TBC
l G48TC
l G48TFA
l G48TD
l G48VA
l G48CEAT
l F48TA
l F48TC
l F48TFA
l S24XA
l S24XC
l T24XA
l G24CEAS
l G24SC
l G24SD
l G24TFA
l X4UXA
l X4UXC
l X4UXD
l X2UXA
l X2UXC
l LE0DX16SFC
00
l LE0DX40SFC
00
l WMNPA
l P1UF
l P4HF
Issue 05 (2012-12-12)
77
Type
Name
5 Boards
Description
l P4CF
Issue 05 (2012-12-12)
Type
Name
Description
SRU
LE2D2SRUDC00/
LE2D2SRUDC01
MCU
MCUA
CMU
CMUA
CKM
CKMA
78
5 Boards
Type
Name
Description
LPU
l G24CA
NOTE
LPUs are classified into S series boards, E series boards, F
series boards, B series boards, and POS boards:
l G24SA
l X12SA
l G48SA
l G48SBC
l G48SC
l G48SD
l G48SFA
l F48SA
l F48SC
l G48TA
l G48TBC
l G48TC
l G48TFA
l G48TD
l G48CEAT
l F48TA
l F48TC
l F48TFA
l S24XA
l S24XC
l T24XA
l G24CEAS
l G24SC
l G24SD
l G24TFA
l X4UXA
l X4UXC
l X4UXD
l X2UXA
l X2UXC
l LE0DX40SFC
00/
LE2D2X40SF
C1
l LE0DX16SFC
00/
LE2D2X16SF
C1
Issue 05 (2012-12-12)
79
Type
Name
5 Boards
Description
l LE2D2X08SE
D0/
LE2D2X08SE
D1
NOTE
l FSUA, VSTSA, and G48VA are supported only on the S9300, and LE2D2X08SED0/LE2D2X08SED1
is supported only on the S9300E.
l GE electrical interfaces do not support the Ethernet synchronization function.
l The Small Form-Factor Pluggable (SFP) is a hot pluggable optical module.
l The 10 Gigabit Small Form-Factor Pluggable (XFP) is a 10G hot pluggable optical module.
l The 10 Gigabit Small Form-Factor Pluggable (SFP+) is a 10G hot pluggable optical module. Its caliber
is smaller than the caliber of the XFP optical module.
l The following cards of the S9300E have not passed the FCC certification: LE2D2SRUDC00, X2UXA,
X2UXC, X4UXA, X4UXC, X4UXD, X12SA, LE0DX40SFC00, LE0DX16SFC00, and
LE2D2X08SED0. All the other cards of the S9300E have passed FCC certification.
l The X12SA of the S9300 have not passed FCC certification. All the other cards of the S9300 have
passed FCC certification.
l The boards gaining the FCC certificate must be used together with the chassis gaining the FCC
certificate.
Issue 05 (2012-12-12)
80
5 Boards
12
LPU
11
LPU
10
LPU
LPU
LPU
SRU
14
SRU
13
LPU
LPU
LPU
LPU
LPU
LPU
CMU
CMU
LPU
LPU
SRU
SRU
LPU
LPU
LPU
CMU
CMU
Issue 05 (2012-12-12)
81
5 Boards
LPU
LPU
MCU
MCU
4/5
Table 5-3, Table 5-4, and Table 5-5 describe the slot distribution on the S9300&S9300E.
Table 5-3 Slot distribution of the S9312&S9312E
Slot
Quant
ity
Height
Note
1-12
12
35.1 mm
13, 14
35.1 mm
Quant
ity
Height
Note
1-6
35.1 mm
7, 8
35.1 mm
Quant
ity
Height
Note
1-3
35.1 mm
4, 5
19.8 mm
Board Dimensions
Table 5-6 provides the dimensions of each board of the S9300&S9300E. For the definitions of
depth, width, and height of a board, see Figure 5-4.
Issue 05 (2012-12-12)
82
5 Boards
MCU
SRU
FSUor VSU
CMU
LPU
CKM
heigtht
depth
width
Issue 05 (2012-12-12)
83
5 Boards
Master
SRU
LPU
LPU
Power
Slave
SRU
Backplane
Fan
Master
CMU
Slave
CMU
Master SRU
control bus
Slave SRU
control bus
Issue 05 (2012-12-12)
84
5 Boards
Master
MCU
LPU
LPU
Backplane
Slave
MCU
Power
Fan
Master MCU
control bus
Slave MCU
control bus
Issue 05 (2012-12-12)
Interface
Category
Interface
Name
Attribute
Type
Board
Optical
interface
Ethernet
optical
interface
FE
LC/PC
F48SA
F48SC
85
Interface
Category
5 Boards
Interface
Name
Attribute
Type
Board
GE
LC/PC
G48SA
G48SC
G48SD
G48SBC
G48SFA
G48CEAT
G24CEAS
S24XA
G24CA
G24SA
G24SC
G24SD
10GE
LC/PC
LE0DX40SFC00/
LE2D2X40SFC1
LE0DX16SFC00/
LE2D2X16SFC1
LE2D2X08SED0/
LE2D2X08SED1
S24XA
S24XC
T24XA
X12SA
X4UXA
X4UXC
X4UXD
X2UXA
X2UXC
POS optical
interface
Electrical
interface
Issue 05 (2012-12-12)
Ethernet
electrical
interface
2.5GE
LC/PC
P1UF
622 Mbit/s
P4HF
155 Mbit/s
P4CF
FE
RJ45
F48TA
F48TTFA
86
Interface
Category
5 Boards
Interface
Name
Attribute
Type
Board
GE
RJ45
G48CEAT
G48TA
G48TC
G48TD
G48TFA
G48VA
G48TBC
T24XA
G24CEAS
G24CA
G24TFA
Ethernet
interface
ETH
10M/100M autosensing
RJ45
Console
interface
RJ45
Environment
monitoring
control
interface
MON
Management
interface of
external PoE
power supplies
RS485
Maintenance
electrical
interface
SRU
MCUA
SRU
MCUA
RJ45
MCUA
CMUA
RJ45
MCUA
CMUA
NOTE
5.2.1 Introduction
The SRU is the control and switching platform of the S9312&S9312E and the
S9306&S9306E. It integrates the control unit, system clock unit, switching unit, and system
maintenance unit. The SRU is the core component for system control and management. As the
clock source and maintenance unit of the system, the SRU is the control plane and maintenance
plane of the system.
Issue 05 (2012-12-12)
87
5 Boards
The SRU has two models: SRUA and SRUB. The SRUA model is divided into two types:
LE0MSRUA and LE0DSRUA. The SRUB model has only one type: LE0D00SRUB00. Table
5-8 lists the SRU models.
The S9300E uses LE2D2SRUDC00/LE2D2SRUDC01 as the MPU.
Table 5-8 SRU models
Name
Switching Capacity
LE0MSRUA
No
LE0DSRUA
Yes
LE0D00SRUB
00
Yes
LE2D2SRUDC
00/
LE2D2SRUDC
01
Yes
NOTE
The SRUA and SRUB apply only to the S9300, and the LE2D2SRUDC00/LE2D2SRUDC01 applies
only to the S9300E.
LE2D2SRUDC01 has gained the FCC certificate, but LE2D2SRUDC00 has not.
The control plane has such functions as protocol processing, service processing, route
calculation, forwarding control, service scheduling, traffic statistics, and system security.
The management plane is responsible for system monitoring, environment monitoring, log
and alarm processing, system loading, and system upgrade.
The switching plane provides high-speed and non-blocking data channels to implement
service switching between service modules. The S9300&S9300E supports double SRUs
in 1+1 hot backup with the data switching units working in load balancing, and main control
boards on the S9300 support flexible card.
Based on the functions, the SRU consists of the following modules physically:
l
Control module: functions as the control and management plane for the SRU and the entire
system, implementing protocol processing, route calculation, forwarding control, system
management, and system security.
Switching module: functions as the service switching plane, providing high-speed service
channels to implement service switching.
Issue 05 (2012-12-12)
88
5 Boards
Local clock module: provides the working clock for the chips of the control module,
switching module, and equipment management and monitoring module.
Equipment management and monitoring module: provides the controller area network bus
(CANBUS) module to monitor the SRU and manage the CANbus modules on the LPUs.
Power supply: provides power supply for the SRU, FSU, and clock pinch board.
FSU: provides enhanced services such as centralized forwarding, network quality analysis
(NQA), Ethernet operation, administration and maintenance (OAM), and NetFlow. It is an
optional value-added service module.
Clock pinch board: provides the stratum-3 clock and synchronization Ethernet clock and
supports IEEE 1588v2. It is an optional clock module.
Stacking card: enables two switches to form a stack. The stacking card is optional.
NOTE
l The SRU stores the configuration data, startup files, upgrade software, and logs.
l The SRUs work in 1+1 hot backup.
l The LE0MSRUA does not support the clock module.
l The SRUs are hot pluggable. Before removing the active SRU, perform the active/standby switchover
first.
Application
The SRUs of the S9312&S9312E are installed in slot 13 and slot 14; the SRUs of the
S9306&S9306E are horizontally installed in slot 7 and slot 8. The SRU slots are in the center
of the subrack of the S9312&S9312E or S9306&S9306E.
The S9312&S9312E or S9306&S9306E must have at least one SRU. You can install one or two
SRUs. If only one SRU is installed, it can be installed in either of the SRU slots. To improve
reliability of a key device, you can install double SRUs. When the master SRU fails, the slave
SRU substitutes for the master SRU automatically to prevent service interruption.
NOTE
5.2.3 Panel
Figure 5-7, Figure 5-8, and Figure 5-9 show the appearances of SRU panels.
Figure 5-7 Appearance of an LE0MSRUA panel
Issue 05 (2012-12-12)
89
5 Boards
Color
Description
RUN/ALM
Green
ACT
Red
Orange
Green
Issue 05 (2012-12-12)
90
5 Boards
Indicator/Button
Color
Description
RST
SYNC
Green
5.2.4 Interfaces
Table 5-10 describes the types and functions of the interfaces on the SRU.
Table 5-10 Types and functions of the interfaces on the SRU
Name
Quantity
Description
ETH (10M/100M
Base-TX autosensing)
Console interface
BITS interface
Issue 05 (2012-12-12)
Table 5-11 describes the attributes of the 10M/100M Base-TX Ethernet interface.
91
5 Boards
Attribute
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3
Attribute
Description
Connector type
RJ45
Operation mode
Compliance
standard
RS-232
Data equipment
type
Description
Connector type
RJ45
Operation mode
Frame format
Compliance
standard
l 1 pps + TOD
NMEA-0183
TOD standard of China Mobile
l DCLS: standard of DCLS signals
l 2 MHz: G.703 standard
l 2 Mbit/s: G.703 standard
l 1.544 Mbit/s: G.703 standard
Issue 05 (2012-12-12)
92
5 Boards
Attribute
Description
Cable
Specification
SRU dimensions
(depth x width x
height)
Maximum power
consumption
Weight
LE0MSRUA: 2.80 kg
LE0DSRUA: 2.90 kg
LE0D00SRUB00: 2.90 kg
LE2D2SRUDC00/LE2D2SRUDC01: 2.90 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.3.1 Introduction
The MCUA is the control and switching platform of the S9303&S9303E. It integrates the control
unit, system clock unit, and system maintenance unit. The MCUA is the core component for
system control and management. In addition, as the clock source and maintenance unit of the
system, the MCUA is the control plane and maintenance plane of the system.
Issue 05 (2012-12-12)
93
5 Boards
The MCUA has two models: LE0MMCUA and LE0DMCUA. The LE0DMCUA has a clock
board and supports time and clock synchronization, which the LE0DMCUA does not support.
Monitoring system operation: The MCUA collects operation data of different units
periodically. According to the running status of the units, the MCUA generates the control
information used to check availability of boards, control the running status of the switching
fabric, perform port switching, reset the forwarding engine, and increase the fan speed.
Working as the proxy of the network management module: The MCUA can manage and
maintain the S9303 and S9303E through the open management interfaces (serial interfaces
or network interfaces).
Implementing data configuration: The MCUA stores the configuration data, startup file,
accounting data, upgrade software, and running logs of the S9303 and S9303E. The
MCUA provides a CF card to store data files.
Working in 1+1 hot backup mode to improve reliability: The master and slave MCUAs
monitor the status of each other. When the master MCUA fails, the slave MCUA substitutes
for the master MCUA to ensure normal running of the system.
Supporting the optional clock board: The LE0DMCUA provides the stratum-3 clock and
Ethernet clock synchronization functions and supports IEEE 1588v2.
NOTE
Application
The MCUAs of the S9303 and S9303E are installed in slot 4 and slot 5.
The S9303 and S9303E must have at least one MCUA. You can install one or two MCUAs. If
only one MCUA is installed, it can be installed in either of the MCUA slots. To improve
reliability of a key device, you can install double MCUAs. When the master MCUA fails, the
slave MCUA substitutes for the master MCUA automatically to prevent service interruption.
5.3.3 Panel
Figure 5-10 and Figure 5-11 show the appearances of the MCUA panels.
Issue 05 (2012-12-12)
94
5 Boards
Color
Description
RUN/ALM
Green
Issue 05 (2012-12-12)
Red
Orange
95
5 Boards
Indicator/Button
Color
Description
ACT
Green
RST
SYNC
Green
5.3.4 Interfaces
Table 5-16 describes the types and functions of the interfaces on an MCUA board.
Table 5-16 Types and functions of the interfaces on an MCUA board
Name
Quantity
Description
ETH (10M/100M
Base-TX autosensing)
Console interface
MON interface
RS485 interface
BITS interface
Issue 05 (2012-12-12)
96
5 Boards
NOTE
Currently, the S9300&S9300E does not support external PoE power supplies.
Table 5-17 describes the attributes of the 10M/100M Base-TX Ethernet interface.
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3
Description
Connector type
RJ45
Operation mode
Compliance
standard
RS-232
Data equipment
type
Specification
Connector type
RJ45
Compliance
standard
RS-485
Issue 05 (2012-12-12)
97
5 Boards
Specification
Connector type
RJ45
Compliance
standard
RS-232
Description
Connector type
RJ45
Operation mode
Frame format
Compliance
standard
l 1 pps + TOD
NMEA-0183
TOD standard of China Mobile
l DCLS: standard of DCLS signals
l 2 MHz: G.703 standard
l 2 Mbit/s: G.703 standard
l 1.544 Mbit/s: G.703 standard
Cable
Issue 05 (2012-12-12)
98
5 Boards
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
l LE0MMCUA: 18 W
Weight
0.90 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.4.1 Introduction
The FSUA is installed on the SRU shown in Figure 5-12. The FSUA provides the features such
as OAM, BFD and security.
The FSUA is an optional subcard on the SRU. It does not provide any interface.
Figure 5-12 Position of FSU in SRU
FSUA
Ensuring security of the CPU on the SRU and limiting the rate of packets sent to the CPU
Issue 05 (2012-12-12)
99
5 Boards
Application
The FSUA is installed on an SRU.
It is an optional subcard on the SRU of the S9312 and S9306, and can be removed and installed
flexibly.
Users can choose to install an FSUA based on the service requirement, which improves service
flexibility and expansibility.
NOTE
To use an FSUA, install the FSUA on the master and slave SRUs.
The FSUA can be installed only with the SRUA and SRUB.
The FSUA is not hot swappable.
5.4.3 Panel
Figure 5-13 shows the appearance of the FSUA panel.
Figure 5-13 Appearance of the FSUA panel
FSUA
Table 5-23 describes the buttons and indicators on the FSUA panel.
Table 5-23 Description of the buttons and indicators on the FSUA panel
Indicator/Button
Color
Description
RUN
Green
Issue 05 (2012-12-12)
100
5 Boards
Specification
Board dimensions
(D x W x H)
Maximum power
consumption
20 W
Weight
0.42 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.5.1 Introduction
Currently, only one type of clock board is available: CKMA. CKMA is a subcard of the main
control board of the S9312&S9312E, S9306&S9306E, or S9303&S9303E. It provides the
functions of clock synchronization and time synchronization and has Building Integrated Timing
Supply System (BITS) interfaces.
Providing the 19.44 MHz system clock and providing external clock signals. The output
clock signal complies with the ITU-T G.813 standard.
Implementing the IEEE 1588 protocol through the logic to ensure synchronization of time
on the network. The time is accurate to 0.1 us, which complies with the 1588v2 protocol.
Application
The CKM is a pinch board be used on the LE03SRUA, LE02SRUB, and LE02SRUD of the
S9306&S9306E and S9312&S9312E and the LE03MCUA of the S9303&S9303E.
Issue 05 (2012-12-12)
101
5 Boards
NOTE
To use the clock pinch board, install a clock pinch board on the master and slave MPUs.
5.5.3 Appearance
Figure 5-14 shows the clock board appearance.
Figure 5-14 Clock board appearance
5.5.4 Interfaces
The CLM has two BITS interfaces, corresponding to the CLK1 and CLK2 interfaces on the main
control board. Table 5-25 describes the types and functions of the two BITS interfaces.
Table 5-25 Types and functions of the BITTS interfaces
Name
Quantity
Description
BITS0
Corresponds to
the CLK1
interface on the
main control
board.
Issue 05 (2012-12-12)
102
5 Boards
Name
Quantity
Description
BITS1
Corresponds to
the CLK2
interface on the
main control
board.
Description
Connector type
RJ45
Operation mode
Transmission rate:
l Clock frequency synchronization: 2 MHz, 2 Mbit/s, 1.544 Mbit/s.
l Time synchronization: 9600 bit/s
Supports full-duplex mode.
Compliance
standard
Issue 05 (2012-12-12)
Item
Specification
Board dimensions
(W x D x H)
Power
consumption
6W
Weight
0.1 kg
Long-term
temperature
0C to 45C
103
5 Boards
Item
Specification
Short-term
temperature
-5C to 55C
5.6.1 Introduction
The stacking card supported by the S9300 is called VSTSA. The VSTSA can be installed on the
SRU of the S9306 or S9312 to provide switch stacking function.
Figure 5-15 Position of VSTSA in SRU
VSTSA
Application
A VSTSA can be installed on the SRU of the S9312 or S9306. To configure the stack, install
the VSTSA on the SRU in the same chassis.
NOTE
5.6.3 Panel
Figure 5-16 shows the appearance of the VSTSA panel.
Issue 05 (2012-12-12)
104
5 Boards
2. Stack ID indicator
3. ACT/LINK indicator
4. RUN/ALM indicator
Color
Description
MASTER
Green
STACK ID
Green
ACT/LINK
Green
Issue 05 (2012-12-12)
105
5 Boards
Indicator/Button
Color
Description
RUN/ALM
Green
Red
5.6.4 Interfaces
Table 5-29 describes the types and functions of the interfaces on the VSTSA.
Table 5-29 Types and functions of the interfaces on the VSTSA
Name
Quantity
Description
The VSTSA card provides four interfaces: S0-0, S0-1, S1-0, and S1-1. The S9300 currently
supports the stack of up to two switches. When S9300A and S9300B are connected through
VSTSAs, the interfaces are connected as Figure 5-17 shows.
Figure 5-17 External cable connections of a stack
SRU
SRU
SRU
SRU
106
5 Boards
Specification
Board dimensions
(depth x width x
height)
Power
consumption
12 W
Weight
1 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.7.1 Introduction
The CMU manages the power supplies and fans of the system uniformly.
The CMUs are installed in the right slots of PWR4, as shown in Figure 5-18.
CMU1
CMU1
CMU2
PWR4
PWR3
PWR2
PWR1
Backplane interface module: sends all interface signals on the backplane to control the
power supply, fans, and master/slave states of CMU.
Issue 05 (2012-12-12)
107
5 Boards
Application
The CMU is applied to the S9312&S9312E, or S9306&S9306E. There are two CMU slots on
the subrack: one for the master CMU and the other for the slave CMU. You can install one or
two CMUs as required.
5.7.3 Panel
Figure 5-19 shows the appearance of the CMU panel.
Figure 5-19 Appearance of the CMU
Color
Description
RUN/ALM
Green
Red
ACT
Green
Issue 05 (2012-12-12)
108
5 Boards
5.7.4 Interfaces
Table 5-32 describes the types and functions of the interfaces on a CMU board.
Table 5-32 Types and functions of the interfaces on a CMU board
Name
Quantity
Description
MON interface
RS485 interface
NOTE
Currently, the S9300&S9300E does not support external PoE power supplies.
Specification
Connector type
RJ45
Compliance
standard
RS-485
Specification
Connector type
RJ45
Compliance
standard
RS-232
109
5 Boards
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
1W
Weight
0.22 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.8.1 Introduction
Functioning as the value-added service (VAS) board of the S9300&S9300E, the Service Process
Unit (SPU) provides service functions such as load balancing, firewalls, Network Address
Translation (NAT), IP Security (IPSec), and NetStream, thus meeting requirements of different
application scenarios for diverse industry networks.
Currently, the SPU supports only one board, namely, VAMPA.
Application
A VAMPA can be installed in any LPU slot of the S9312, S9306, or S9303.
NOTE
5.8.3 Panel
Issue 05 (2012-12-12)
110
5 Boards
1. ACT indicator
2. LINK indicator
The board indicator RUN/ALM and interface indicators ACT and LINK are located on the
VAMPA panel. Table 5-36 describes the colors and blinking states of the indicators.
Table 5-36 Buttons and indicators on the VAMPA panel
Indicator/Button
Color
Description
RUN/ALM
Green
ACT
Red
Orange
Amber
LINK
Green-yellow
5.8.4 Interfaces
Table 5-37 describes types and functions of interfaces on the VAMPA.
Issue 05 (2012-12-12)
111
5 Boards
Quantity
Description
Console interface
Ethernet interface
Description
Connector type
RJ45
Interface attribute
RS232
Compliance standard
EIA/TIA-232
Description
Connector type
RJ45
Interface attribute
10BASE-T/100BASE-TX
Operation mode
Full duplex
Compliance standard
IEEE 802.3
Issue 05 (2012-12-12)
112
5 Boards
Description
Board dimensions (W x D x H)
120 W
Board weight
2.6 kg
5.9.1 Introduction
The 48-port optical interface line card (SFP) of the S9300&S9300E is called G48S and has the
following models: (EA, SFP), (EC, SFP), (ED, SFP), and (FA, SFP).
Table 5-41 lists the board full names and MAC address table capacities.
Table 5-41 G48S models
Full Name
Short Name
G48SA
32K
G48SC
128K
G48SD
512K
G48SFA
32K
Both the G48SA and G48SFA support 32K MAC address entries. The power consumption of a
G48SFA is smaller than that of a G48SA.
113
5 Boards
Application
The G48S can be installed in any LPU slot on the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.9.3 Panel
Figure 5-21 shows the appearance of the G48S panel.
Figure 5-21 Appearance of the G48S panel
Color
Description
RUN/ALM
Green
Issue 05 (2012-12-12)
Red
Orange
ACT
Amber
LINK
Green-yellow
114
5 Boards
5.9.4 Interfaces
Interfaces
Table 5-43 describes the types and functions of the interfaces on the G48S.
Table 5-43 Types and functions of the interfaces on the G48S
Name
Quantity
Description
48
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
115
5 Boards
Attri
bute
Description
Cent
er
wave
lengt
h
850 nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
Rece
iver
sensi
tivity
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Table 5-46 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
80 km
116
5 Boards
Attribut
e
Description
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
Table 5-47 Attributes of an ESFP-DWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
120 km
Center
waveleng
th
1529.5
5 nm
1533.4
7 nm
1537.4
0 nm
1541.3
5 nm
1545.3
2 nm
1549.3
2 nm
1553.3
3 nm
1557.3
6 nm
1530.3
3 nm
1534.2
5 nm
1538.1
9 nm
1542.1
4 nm
1546.1
2 nm
1550.1
2 nm
1554.1
3 nm
1558.1
7 nm
1531.1
2 nm
1535.0
4 nm
1538.9
8 nm
1542.9
4 nm
1546.9
2 nm
1550.9
2 nm
1554.9
4 nm
1558.9
8 nm
1531.9
0 nm
1535.8
2 nm
1539.7
7 nm
1543.7
3 nm
1547.7
2 nm
1551.7
2 nm
1555.7
5 nm
1559.7
9 nm
1532.6
8 nm
1536.6
1 nm
1540.5
6 nm
1544.5
3 nm
1548.5
1 nm
1552.5
2 nm
1556.5
6 nm
1560.6
1 nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
117
5 Boards
Attribut
e
Description
Overload
optical
power
-8.0 dBm
Extinctio
n ratio
8.2 dB
Operatin
g
temperat
ure
0C to 45C
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
Network protocol
IP
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
G48SA: 75 W
G48SC: 92 W
G48SD: 110 W
G48SFA: 65 W
Issue 05 (2012-12-12)
118
5 Boards
Item
Specification
Weight
G48SA: 2.54 kg
G48SC: 2.66 kg
G48SD: 2.66 kg
G48SFA: 2.60 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.10.1 Introduction
The 48-port 100M/1000M optical interface line card (BC, SFP) of the S9300&S9300E is called
G48SBC and provides 48 100M/1000M Ethernet interfaces. It supports 128K MAC address
entries.
Application
A G48SBC board can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.10.3 Panel
Figure 5-22 shows the appearance of the G48SBC panel.
Issue 05 (2012-12-12)
119
5 Boards
RUN/ALM
Color
Description
RUN/ALM
Green
Red
Orange
ACT indicator of
optical interfaces
Amber
Link indicator of
optical interfaces
Green-yellow
5.10.4 Interfaces
Table 5-51 describes the types and functions of the interfaces on the G48SBC.
Issue 05 (2012-12-12)
120
5 Boards
Quantity
Description
100M/1000M BASE-X
optical interface
48
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
121
5 Boards
Attri
bute
Description
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Table 5-54 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1471
nm
Transmit
optical
power
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
122
5 Boards
Attribut
e
Description
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
Table 5-55 Attributes of an ESFP-DWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
120 km
Center
waveleng
th
1529.5
5 nm
1533.4
7 nm
1537.4
0 nm
1541.3
5 nm
1545.3
2 nm
1549.3
2 nm
1553.3
3 nm
1557.3
6 nm
1530.3
3 nm
1534.2
5 nm
1538.1
9 nm
1542.1
4 nm
1546.1
2 nm
1550.1
2 nm
1554.1
3 nm
1558.1
7 nm
1531.1
2 nm
1535.0
4 nm
1538.9
8 nm
1542.9
4 nm
1546.9
2 nm
1550.9
2 nm
1554.9
4 nm
1558.9
8 nm
1531.9
0 nm
1535.8
2 nm
1539.7
7 nm
1543.7
3 nm
1547.7
2 nm
1551.7
2 nm
1555.7
5 nm
1559.7
9 nm
1532.6
8 nm
1536.6
1 nm
1540.5
6 nm
1544.5
3 nm
1548.5
1 nm
1552.5
2 nm
1556.5
6 nm
1560.6
1 nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-8.0 dBm
Extinctio
n ratio
8.2 dB
123
5 Boards
Attribut
e
Description
Operatin
g
temperat
ure
0C to 45C
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
Network protocol
IP
Specification
Dimensions (depth
x width x height)
Maximum power
consumption
185 W
Weight
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 50C
124
5 Boards
5.11.1 Introduction
The 48-port GE electrical interface card (RJ45) of the S9300&S9300E is called G48T for short
and has the following models: 48-port 10M/100M/1000M electrical interface card (EA, RJ45),
48-port 10M/100M/1000M electrical interface card (EC, RJ45), 48-port 10M/100M/1000M
electrical interface card (ED, RJ45), and 48-port 10M/100M/1000M electrical interface card
(FA, RJ45).
Table 5-58 provides the full name of the interface cards and capacities of their MAC address
tables.
Table 5-58 Lists of G48T cards
Full Name
Short Name
Capacity of MAC
Address Table
G48TA
32K
G48TC
128K
G48TD
512K
G48TFA
32K
Both the G48TA and G48TFA support 32K MAC addresses. The power consumption of the
G48STA is smaller than that of the G48TA.
Application
The G48T can be installed in any LPU slot on the S9312&S9312E, S9306&S9306E or
S9303&S9303E.
5.11.3 Panel
Figure 5-23 shows the appearance of the G48T panel.
Issue 05 (2012-12-12)
125
5 Boards
36 37 38 39 40 41 42 43 4445 4647
Color
Description
RUN/ALM
Green
Link/ACT
Red
Orange
Green
5.11.4 Interfaces
Table 5-60 describes the types and functions of the interfaces on the G48T.
Issue 05 (2012-12-12)
126
5 Boards
Quantity
Description
10M/100M/1000M
BASE-T electrical
interface
48
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Specification
Dimensions (H x
W x D)
Maximum power
consumption
G48TA: 62 W
G48TC: 68 W
G48TD: 98 W
G48TFA: 48 W
Weight
G48TA: 2.50 kg
G48TC: 2.66 kg
G48TD: 2.66 kg
G48TFA: 2.50 kg
Long-term
temperature
Issue 05 (2012-12-12)
0C to 45C
127
5 Boards
Item
Specification
Short-term
temperature
-5C to 55C
5.12.1 Introduction
The 48-port 10M/100M/1000M Ethernet electrical interface line card (BC, RJ45) of the
S9300&S9300E is called 48TBC and provides 48 10M/100M/1000M Ethernet interfaces. It
supports 128K MAC address entries.
Application
A G48TBC board can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.12.3 Panel
Figure 5-24 shows the appearance of the G48TBC panel.
Figure 5-24 Appearance of the G48TBC panel
1 2
RUN/ALM
Issue 05 (2012-12-12)
128
5 Boards
Color
Description
RUN/ALM
Green
ACT/Link
indicators of
electrical interfaces
Red
Orange
Green
5.12.4 Interfaces
Table 5-64 describes the types and functions of the interfaces on the G48TBC.
Table 5-64 Types and functions of the interfaces on the G48TBC
Name
Quantity
Description
10M/100M/1000M
BASE-T electrical
interface
48
129
5 Boards
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Specification
Dimensions (depth
x width x height)
Maximum power
consumption
160 W
Weight
2.90 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 50C
5.13.1 Introduction
The 48-port 10/100M/1000M Ethernet PoE electrical interface card (EA, RJ45, PoE) is called
G48VA for short.
The G48VA is a GE electrical interface card. It supports the power over Ethernet (PoE) function.
Issue 05 (2012-12-12)
130
5 Boards
The G48VA provides 48 GE interfaces and such functions as the data switching unit and PoE
management unit. The G48VA has the following functions:
l
Providing data signals and DC power for the directly connected devices such as the IP
phone, access point (AP) of the wireless local area network (WLAN), and Web camera
Data switching unit: consists of the CPU, LAN switch, and physical layer (PHY).
PoE management unit: consists of the CPU and the Dual Inline Memory Module (DIMM).
Application
The G48VA can be installed in any LPU slot of the S9303, S9306 or S9312.
The G48VA can provide the PoE function only when the chassis supports the PoE function.
NOTE
The G48VA only applies to S9300, but does not apply to S9300E.
The G48VA can start and register only when the following conditions are met:
l The DIMM module is installed in the DIMM slot on the board.
l The PoE chassis is used..
l A PoE power supply is installed and working normally.
5.13.3 Panel
Figure 5-25 shows the appearance of the G48VA panel.
Figure 5-25 Appearance of the G48VA panel
Issue 05 (2012-12-12)
131
5 Boards
Color
Meaning
RUN/ALM
Green
Link/ACT
Red
Orange
Green
5.13.4 Interfaces
Table 5-68 describes the types and functions of the interfaces on the G48VA.
Table 5-68 Types and functions of the interfaces on the G48VA
Name
Quantity
Description
10M/100M/1000M
BASE-T electrical
interface
48
Issue 05 (2012-12-12)
132
5 Boards
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
Weight
2.60 kg
Maximum output
power
Interface: 30 W
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
Board: 1440 W
5.14.1 Introduction
Issue 05 (2012-12-12)
133
5 Boards
Application
A G48CEAT can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.14.3 Panel
Figure 5-26 shows the appearance of the G48CEAT panel.
Figure 5-26 Appearance of the G48CEAT panel
Issue 05 (2012-12-12)
134
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT indicator of
optical interfaces
Amber
Link indicator of
optical interfaces
Green-yellow
ACT/Link
indicators of
electrical interfaces
Green
5.14.4 Interfaces
Table 5-72 describes the types and functions of the interfaces on the G48CEAT.
Table 5-72 Types and functions of the interfaces on the G48CEAT
Name
Quantity
Description
100M/1000M BASE-X
optical interface
12
10M/100M/1000M
BASE-T electrical
interface
36
135
5 Boards
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
136
5 Boards
Attri
bute
Description
Extin
ction
ratio
9 dB
9 dB
Fiber
type
Multimode
Single-mode
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Table 5-75 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
137
5 Boards
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
Network protocol
IP
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Issue 05 (2012-12-12)
Item
Specification
Board dimensions
(depth x width x
height)
Power
consumption
62 W
Weight
2.50 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
138
5 Boards
5.15.1 Introduction
The 48-port FE optical interface line card (SFP) of the S9300&S9300E is called F48S and
provides the following models: (EA, SFP) and (EC, SFP). (EA, SFP) and (EC, SFP) support
different numbers of MAC address entries.
Table 5-79 lists the board full names and MAC address table capacities.
Table 5-79 F48S models
Full Name
Short Name
MAC Address
Table Capacity
F48SA
32K
F48SC
128K
Application
An F48S board can be installed in any LPU slot on the S9303&S9303E, S9306&S9306E, or
S9312&S9312E.
5.15.3 Panel
Figure 5-27 shows the appearance of an F48S panel.
Issue 05 (2012-12-12)
139
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
LINK
Green-yellow
5.15.4 Interfaces
Table 5-81 describes the types and functions of the interfaces on the F48S.
Issue 05 (2012-12-12)
140
5 Boards
Quantity
Description
100M BASE-FX
optical interface
48
Description
Connector
LC/PC
Optical interface
attribute
Determined by the SFP optical module. For details about the attributes
of the optical module, see Table 5-83.
Standards
compliance
IEEE 802.3u
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attrib
ute
Description
Transm
ission
distanc
e
2 km
15 km
15 km (single-mode
bidirectional fiber)
40 km
80 km
Center
wavele
ngth
1310 nm
1310 nm
Tx: 1310
nm
Tx: 1550
nm
1310 nm
1550 nm
Rx: 1550
nm
Rx: 1310
nm
Transm
it
power
-19.0 dBm
to -14.0
dBm
-15.0 dBm
to -8.0
dBm
-15.0 dBm
to -8.0
dBm
-5.0 dBm
to 0 dBm
-5.0 dBm
to 0 dBm
-15.0 dBm
to -8.0
dBm
141
5 Boards
Attrib
ute
Description
Receiv
er
sensitiv
ity
-30.0 dBm
-31.0 dBm
-32.0 dBm
-32.0 dBm
-37.0 dBm
-37.0 dBm
Overlo
ad
optical
power
-14.0 dBm
-8.0 dBm
-8.0 dBm
-8.0 dBm
-10.0 dBm
-10.0 dBm
Extincti
on ratio
10 dB
8.2 dB
8.5 dB
8.5 dB
10.5 dB
10.5 dB
Fiber
type
Multimode
Single-mode
Specification
Dimensions (depth
x width x height)
Maximum power
consumption
F48SA: 64 W
Weight
F48SA: 2.54 kg
F48SC: 76 W
F48SC: 2.66 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
Issue 05 (2012-12-12)
142
5 Boards
5.16.1 Introduction
The 48-port FE electrical interface line card (RJ45) of the S9300&S9300E is called F48T and
has the following models: (EA, RJ45), (EC, RJ45), and (FA, RJ45).
Table 5-85 lists the board full names and MAC address table capacities.
Table 5-85 F48T models
Full Name
Short Name
MAC Address
Table Capacity
F48TA
32K
F48TC
128K
F48TFA
32K
Both the F48TA and F48TFA support 32K MAC address entries. The power consumption of an
F48TFA board is smaller than that of an F48TA board.
Application
An F48T can be installed in any LPU slot on the S9312&S9303E, S9306&S9306E or,
S9303&S9303E.
5.16.3 Panel
Figure 5-28 shows the appearance of an F48T panel.
Issue 05 (2012-12-12)
143
5 Boards
0 1 2 3 4 5 6 7 8
9 10 11
12 13
24 25 26 27 28 29 30 31 32 33 34 35
36 37 3839 40 41 42 43 44 45 46 47
1. Link/ACT indicator of the upper electrical interfaces 2. Link/ACT indicator of the lower electrical interfaces
Color
Description
RUN/ALM
Green
Link/ACT
Red
Orange
Green
5.16.4 Interfaces
Table 5-87 describes the types and functions of the interfaces on an F48T.
Issue 05 (2012-12-12)
144
5 Boards
Quantity
Description
10M/100M BASE-T
electrical interface
48
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3
Frame format
Network protocol
IP
Specification
Dimensions (depth
x width x height)
Maximum power
consumption
F48TA: 59 W
F48TC: 70 W
F48TFA: 40 W
Weight
F48TA: 2.50 kg
F48TC: 2.66 kg
F48TFA: 2.30 kg
Issue 05 (2012-12-12)
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
145
5 Boards
5.17.1 Introduction
The 40-port 10GE optical interface line card (FC, SFP+) of the S9300&S9300E is called
LE0DX40SFC00/LE2D2X40SFC1 and provides 40 10GE interfaces. It supports 128K MAC
address entries.
Application
An LE0DX40SFC00 board can be installed in any LPU slot of the S9312&S9312E,
S9306&S9306E, or S9303&S9303E.
An LE2D2X40SFC1 board can be installed in any LPU slot of the S9312E, S9306E, or
S9303E.
5.17.3 Panel
Figure 5-29 shows the appearance of the LE0DX40SFC00/LE2D2X40SFC1 panel.
Figure 5-29 Appearance of the LE0DX40SFC00/LE2D2X40SFC1 panel
1234
RUN/ALM
Issue 05 (2012-12-12)
146
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
Link
Green-yellow
5.17.4 Interfaces
Table 5-91 describes the types and functions of the interfaces on the LE0DX40SFC00.
Table 5-91 Types and functions of the interfaces on the LE0DX40SFC00
Name
Quantity
Description
10G BASE-SFP+/
1000M BASE-X optical
interface
40
147
5 Boards
Description
Connector
LC/PC
Optical interface
attribute
Determined by the optical module. For details about the attributes of the
optical module, see Table 5-94 and Table 5-95.
Standards
compliance
IEEE 802.3ae
Frame format
Network protocol IP
When SFP+ cables are used as interface cables, the interface arributes are shown in Table
5-93.
Table 5-93 Attributes of a 10G Base-SFP+ Ethernet optical interface
Attribute
Description
Connector
SFP+
Standards
compliance
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attribute
Description
Transmission
distance
220 m
300 m
10 km
Center
wavelength
1310 nm
850 nm
1310 nm
Transmit power
Receiver
sensitivity
-6.5 dBm
-11.1 dBm
-12.6 dBm
Overload
optical power
1.5 dBm
-1.0 dBm
0.5 dBm
Extinction ratio
3.5 dB
3.0 dB
3.5 dB
Fiber type
OM1/OM2, multimode
OM3, multi-mode
Single-mode
148
5 Boards
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx1310
nm
Tx1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx1490
nm
Rx1310
nm
Tran
smit
optic
al
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5.0
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23,0
dBm
-22.0
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9.0 dB
9.0 dB
6.0 dB
6.0 dB
9.0 dB
8.5 dB
9.0 dB
8.0 dB
Optic
al
fiber
type
Multimode
Single-mode
Issue 05 (2012-12-12)
149
5 Boards
Specification
Dimensions (depth x
width x height)
Maximum power
consumption
183 W
Weight
2.90 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 45C
5.18.1 Introduction
The 16-port 10GE optical interface card (FC, SFP+) of the S9300&S9300E is called
LE0DX16SFC00/LE2D2X16SFC1 and provides 16 10GE interfaces. It supports 128K MAC
address entries.
Application
An LE0DX16SFC00 board can be installed in any LPU slot of the S9312&S9312E,
S9306&S9306E, or S9303&S9303E.
An LE2D2X16SFC1 board can be installed in any LPU slot of the S9312E, S9306E, or
S9303E.
5.18.3 Panel
Figure 5-30 shows the appearance of an LE0DX16SFC00/LE2D2X16SFC1 panel.
Issue 05 (2012-12-12)
150
5 Boards
RUN/ALM
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
Link
Green-yellow
5.18.4 Interfaces
Table 5-98 describes the types and functions of interfaces on an LE0DX16SFC00/
LE2D2X16SFC1 board.
Issue 05 (2012-12-12)
151
5 Boards
Quantity
Description
10GE BASE-SFP+/
1000M BASE-X optical
interface
16
Description
Connector
LC/PC
Optical interface
attribute
Determined by the SFP+ optical module. For details about the optional
optical module attributes, see Table 5-100 and Table 5-101.
Standards
compliance
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attribute
Description
Transmission
distance
220 m
300 m
10 km
Center
wavelength
1310 nm
850 nm
1310 nm
Transmit
optical power
Receiver
sensitivity
-6.5 dBm
-11.1 dBm
-12.6 dBm
Overload
optical power
1.5 dBm
-1.0 dBm
0.5 dBm
Extinction ratio
3.5 dB
3.0 dB
3.5 dB
152
5 Boards
Attribute
Description
Optical fiber
type
OM1/OM2 multimode
OM3 multi-mode
Single-mode
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
153
5 Boards
Attri
bute
Description
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Description
Dimensions (depth
x width x height)
Maximum power
consumption
150 W
Weight
2.60 kg
Long-term
operating
temperature
0C to 45C
Short-term
operating
temperature
-5C to 45C
Issue 05 (2012-12-12)
154
5 Boards
5.19.1 Introduction
The 24-port 100M/1000M Ethernet optical interface + 8-port 10M/100M/1000M Combo
electrical interface line card (SA, SFP/RJ45) is called G24CA and provides 8 electrical interfaces
and 24 optical interfaces. The first eight optical interfaces are used with the eight electrical
interfaces as combo interfaces.
On the G24CA, at most 24 interfaces, including the GE interfaces and combo interfaces, can work at the
same time.
Application
A G24CA can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.19.3 Panel
Figure 5-31 shows the appearance of the G24CA panel.
Figure 5-31 Appearance of the G24CA panel
1. Link/ACT indicators of the upper 2. Link/ACT indicators of the lower 3. ACT indicators of the lower
electrical interfaces
electrical interfaces
optical interfaces
4. ACT indicators of the upper
optical interfaces
Issue 05 (2012-12-12)
155
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
LINK
Green-yellow
Link/ACT
Green
5.19.4 Interfaces
Table 5-104 describes the types and functions of the interfaces on the G24CA.
Table 5-104 Types and functions of the interfaces on the G24CA
Issue 05 (2012-12-12)
Name
Quantity
Description
100/1000M BASE-T
electrical interface
100/1000M BASE-X
optical interface
24
156
5 Boards
NOTE
A Combo interface works as either an optical interface or an electrical interface. You can run the comboport { auto | copper | fiber } command to set the mode of the Combo interface.
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
157
5 Boards
Attri
bute
Description
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Table 5-107 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
158
5 Boards
Table 5-108 Attributes of an ESFP-DWDM optical module (100 Mbit/s or 1000 Mbit/s)
Attribut
e
Description
Transmis
sion
distance
120 km
Center
waveleng
th
1529.5
5 nm
1533.4
7 nm
1537.4
0 nm
1541.3
5 nm
1545.3
2 nm
1549.3
2 nm
1553.3
3 nm
1557.3
6 nm
1530.3
3 nm
1534.2
5 nm
1538.1
9 nm
1542.1
4 nm
1546.1
2 nm
1550.1
2 nm
1554.1
3 nm
1558.1
7 nm
1531.1
2 nm
1535.0
4 nm
1538.9
8 nm
1542.9
4 nm
1546.9
2 nm
1550.9
2 nm
1554.9
4 nm
1558.9
8 nm
1531.9
0 nm
1535.8
2 nm
1539.7
7 nm
1543.7
3 nm
1547.7
2 nm
1551.7
2 nm
1555.7
5 nm
1559.7
9 nm
1532.6
8 nm
1536.6
1 nm
1540.5
6 nm
1544.5
3 nm
1548.5
1 nm
1552.5
2 nm
1556.5
6 nm
1560.6
1 nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-8.0 dBm
Extinctio
n ratio
8.2 dB
Operatin
g
temperat
ure
0C to 45C
Issue 05 (2012-12-12)
Attribute
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
159
5 Boards
Attribute
Description
Network protocol
IP
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
67 W
Weight
2.26 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
160
5 Boards
5.20.1 Introduction
The 24-port 100M/1000M Ethernet optical interface + 8-port 100M/1000M combo electrical
interface line card (EA, SFP/RJ45, 1588) is called G24CEAS and provides 8 electrical interfaces
and 24 optical interfaces. Among the 24 optical interfaces, there are eight combo interfaces.
NOTE
When using the G24CEAS, install the CKM on the main control board. When the S9300&S9300E uses
two main control boards, install CKMs on the two main control boards.
Application
A G24CEAS board can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E,
or S9303&S9303E.
5.20.3 Panel
Figure 5-32 shows the appearance of the G24CEAS panel.
Figure 5-32 Appearance of the G24CEAS panel
1. Link/ACT indicators of the upper 2. Link/ACT indicators of the lower 3. ACT indicators of the lower
electrical interfaces
electrical interfaces
optical interfaces
4. ACT indicators of the upper
optical interfaces
Issue 05 (2012-12-12)
161
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
LINK
Green-yellow
LINK/ACT
Green
5.20.4 Interfaces
Table 5-113 describes the types and functions of the interfaces on the G24CEAS.
Table 5-113 Types and functions of the interfaces on the G24CEAS
Issue 05 (2012-12-12)
Name
Quantity
Description
10M/100M/1000M
BASE-T electrical
interface
24
162
5 Boards
NOTE
A Combo interface works as either an optical interface or an electrical interface. You can run the comboport { auto | copper | fiber } command to set the mode of the Combo interface.
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
163
5 Boards
Attri
bute
Description
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Table 5-116 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
164
5 Boards
Table 5-117 Attributes of an ESFP-DWDM optical module (100 Mbit/s or 1000 Mbit/s)
Attribut
e
Description
Transmis
sion
distance
120 km
Center
waveleng
th
1529.5
5 nm
1533.4
7 nm
1537.4
0 nm
1541.3
5 nm
1545.3
2 nm
1549.3
2 nm
1553.3
3 nm
1557.3
6 nm
1530.3
3 nm
1534.2
5 nm
1538.1
9 nm
1542.1
4 nm
1546.1
2 nm
1550.1
2 nm
1554.1
3 nm
1558.1
7 nm
1531.1
2 nm
1535.0
4 nm
1538.9
8 nm
1542.9
4 nm
1546.9
2 nm
1550.9
2 nm
1554.9
4 nm
1558.9
8 nm
1531.9
0 nm
1535.8
2 nm
1539.7
7 nm
1543.7
3 nm
1547.7
2 nm
1551.7
2 nm
1555.7
5 nm
1559.7
9 nm
1532.6
8 nm
1536.6
1 nm
1540.5
6 nm
1544.5
3 nm
1548.5
1 nm
1552.5
2 nm
1556.5
6 nm
1560.6
1 nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-8.0 dBm
Extinctio
n ratio
8.2 dB
Operatin
g
temperat
ure
0C to 45C
Issue 05 (2012-12-12)
Attribute
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
165
5 Boards
Attribute
Description
Network protocol
IP
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
75 W
Weight
2.7 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
Issue 05 (2012-12-12)
166
5 Boards
5.21.1 Introduction
The 24-port 100M/1000M Ethernet optical interface + 2-port 10GE optical interface line card
(SFP/XFP) of the S9300&S9300E is called S24X and has the following models: (EA, SFP/
XFP) and (EC, SFP/XFP).
Table 5-121 lists the board full names and MAC address table capacities.
Table 5-121 S24X models
Full Name
Short Name
S24XA-24-port
100/1000BASE-X and 2port 10GBASE-X interface
line card (EA, SFP/XFP)
S24XA
32K
S24XA-24-port
100/1000BASE-X and 2port 10GBASE-X interface
line card (EC, SFP/XFP)
S24XC
128K
Application
An S24X board can be installed in any LPU slot of the S9303&S9303E, S9306&S9306E, or
S9312&S9312E.
5.21.3 Panel
Figure 5-33 shows the appearance of an S24X panel.
Issue 05 (2012-12-12)
167
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
Link
Green-yellow
5.21.4 Interfaces
Table 5-123 describes the types and functions of the interfaces on an S24X board.
Issue 05 (2012-12-12)
168
5 Boards
Quantity
Description
100M/1000M BASE-X
optical interface
24
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network
protocol
IP
Issue 05 (2012-12-12)
Attr
ibut
e
Description
Tran
smis
sion
dista
nce
500 m
10 km
10 km (singlemode
bidirectional
fiber)
40 km
40 km
80 km
100 km
169
5 Boards
Attr
ibut
e
Description
Cent
er
wav
elen
gth
850 nm
Tran
smitt
ing
pow
er
-9.5
dBm to
-2.5
dBm
Rece
iver
sensi
tivit
y
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
pow
er
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Exti
nctio
n
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fibe
r
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamet
er: 50
um
Issue 05 (2012-12-12)
170
5 Boards
Table 5-126 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
wavelen
gth
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
Table 5-127 Attributes of an ESFP-DWDM optical module (100 Mbit/s or 1000 Mbit/s)
Attribu
te
Description
Transmi
ssion
distance
120 km
Center
wavelen
gth
1529.5
5 nm
1533.4
7 nm
1537.4
0 nm
1541.3
5 nm
1545.3
2 nm
1549.3
2 nm
1553.3
3 nm
1557.3
6 nm
1530.3
3 nm
1534.2
5 nm
1538.1
9 nm
1542.1
4 nm
1546.1
2 nm
1550.1
2 nm
1554.1
3 nm
1558.1
7 nm
1531.1
2 nm
1535.0
4 nm
1538.9
8 nm
1542.9
4 nm
1546.9
2 nm
1550.9
2 nm
1554.9
4 nm
1558.9
8 nm
1531.9
0 nm
1535.8
2 nm
1539.7
7 nm
1543.7
3 nm
1547.7
2 nm
1551.7
2 nm
1555.7
5 nm
1559.7
9 nm
1532.6
8 nm
1536.6
1 nm
1540.5
6 nm
1544.5
3 nm
1548.5
1 nm
1552.5
2 nm
1556.5
6 nm
1560.6
1 nm
Transmit
optical
power
Issue 05 (2012-12-12)
171
5 Boards
Attribu
te
Description
Receiver
sensitivit
y
-28.0 dBm
Overloa
d optical
power
-8.0 dBm
Extinctio
n ratio
8.2 dB
Operatin
g
temperat
ure
0C to 45C
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
70 km
Center
wavelen
gth
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-21.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
172
5 Boards
Description
Transmi
ssion
distance
80 km
Center
wavelen
gth
1529.5
5 nm
1530.3
3 nm
1531.1
2 nm
1531.9
0 nm
1532.6
8 nm
1533.4
7 nm
1534.2
5 nm
1535.0
4 nm
1548.5
1 nm
1549.3
2 nm
1550.1
2 nm
1550.9
2 nm
1551.7
2 nm
1552.5
2 nm
1553.3
3 nm
1554.1
3 nm
Transmit
optical
power
Receiver
sensitivit
y
-24.0 dBm
Overloa
d optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
Attribute
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
Network protocol
IP
Issue 05 (2012-12-12)
Attribute
Description
Connector
LC/PC
Optical interface
attribute
173
5 Boards
Attribute
Description
Standards
compliance
IEEE 802.3ae
Frame format
Network
protocol
IP
Description
Transmissi
on distance
300 m
10 km
40 km
80 km
Center
wavelength
850 nm
1310 nm
1550 nm
1550 nm
Transmit
power
0 dBm to 4.0
dBm
Receiver
sensitivity
-7.5 dBm
-11.0 dBm
-15.0 dBm
-24.0 dBm
Overload
optical
power
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Extinction
ratio
3.0 dB
6.0 dB
8.2 dB
9.0 dB
Fiber type
Multi-mode
Single-mode
Description
Dimensions (depth
x width x height)
Power
consumption
S24XA: 65 W
Weight
S24XA: 2.4 kg
S24XC: 81 W
S24XC: 2.5 kg
Issue 05 (2012-12-12)
174
5 Boards
Parameter
Description
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.22.1 Introduction
The 24-port 10M/100M/1000M Ethernet electrical and 2-port 10GE optical interface line card
(EA, RJ45/XFP) is called T24XA and provides 24 GE electrical interfaces and 2 10GE optical
interfaces.
Application
The T24XA can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.22.3 Panel
Figure 5-34 shows the appearance of the T24XA panel.
Issue 05 (2012-12-12)
175
5 Boards
Color
Meaning
RUN/ALM
Green
Red
Orange
ACT
Amber
LINk
Green-yellow
Link/ACT
Green
5.22.4 Interfaces
Issue 05 (2012-12-12)
176
5 Boards
Table 5-135 describes the types and functions of the interfaces on the T24XA.
Table 5-135 Types and functions of the interfaces on the T24XA
Name
Quantity
Description
10M/100M/1000M
BASE-T electrical
interface
24
Table 5-136 lists the attributes of the 10M/100M/1000M Base-T electrical interface.
Table 5-136 Attributes of the 10M/100M/1000M Base-T Ethernet interface
Attribute
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
Table 5-137, Table 5-138, Table 5-139 and Table 5-140describe the attributes of the 10GE
interfaces and the connected optical modules.
Table 5-137 Attributes of the 10G Base-XFP optical interface
Issue 05 (2012-12-12)
Attribute
Description
Connector type
LC/PC
Optical interface
attribute
Depending on the SFP optical module. For details about the attributes
of the optical module, see Table 5-138.
Compliance
standard
IEEE 802.3ae
Frame format
177
5 Boards
Attribute
Description
Network
protocol
IP
Description
Transmissi
on distance
300 m
10 km
40 km
80 km
Center
wavelength
850 nm
1310 nm
1550 nm
1550 nm
Transmitti
ng power
0 dBm to 4 dBm
Receiver
sensitivity
-7.5 dBm
-11.0 dBm
-15.0 dBm
-24.0 dBm
Overload
optical
power
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Fiber type
Multi-mode
Single-mode
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
70 km
Center
wavelen
gth
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-21.0 dBm
Overload
optical
power
-9.0 dBm
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
178
5 Boards
Attribut
e
Description
Extinctio
n ratio
8.2 dB
Description
Transmi
ssion
distance
80 km
Center
wavelen
gth
1529.5
5 nm
1530.3
3 nm
1531.1
2 nm
1531.9
0 nm
1532.6
8 nm
1533.4
7 nm
1534.2
5 nm
1535.0
4 nm
1548.5
1 nm
1549.3
2 nm
1550.1
2 nm
1550.9
2 nm
1551.7
2 nm
1552.5
2 nm
1553.3
3 nm
1554.1
3 nm
Transmit
optical
power
Receiver
sensitivit
y
-24.0 dBm
Overloa
d optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
Issue 05 (2012-12-12)
Item
Specification
Board dimensions
(depth x width x
height)
Power
consumption
53 W
179
5 Boards
Item
Specification
Weight
2.30 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.23.1 Introduction
The 24-port 100M/1000M optical interface line card (SFP) of the S9300&S9300E is called G24S
and has the following models: (ED, SFP), (SA, SFP) and (EC, SFP).
Table 5-142 lists the board full names and MAC address table capacities.
Table 5-142 G24S models
Full Name
Short Name
MAC Address
Table Capacity
G24SA
32K
G24SC
128K
G24SD
512K
NOTE
Issue 05 (2012-12-12)
180
5 Boards
Application
The G24S can be installed in any LPU slot on the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.23.3 Panel
Figure 5-35 and Figure 5-36 show the appearances of the G24S panels.
Figure 5-35 Appearance of the G24SA panel
Issue 05 (2012-12-12)
181
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
LINK
Green-yellow
5.23.4 Interfaces
Table 5-144 describes the types and functions of the interfaces on the G24S.
Table 5-144 Types and functions of the interfaces on the G24S
Name
Quantity
Description
100/1000BASE-X
optical interface
24
Issue 05 (2012-12-12)
Attribute
Description
Connector type
LC/PC
Optical interface
attribute
182
5 Boards
Attribute
Description
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attri
bute
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
183
5 Boards
Attri
bute
Description
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Table 5-147 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
Issue 05 (2012-12-12)
Attribute
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
184
5 Boards
Attribute
Description
Frame format
Network protocol
IP
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
G24SA: 45 W
G24SC: 63 W
G24SD: 75 W
Weight
G24SA: 2.22 kg
G24SC: 2.66 kg
G24SD: 2.66 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.24.1 Introduction
The 24-Port 10/100/1000BASE-T Interface Card(FA,RJ45) is called G24TFA for short. The
G24TFA provides twenty-four 10M/100M/1000M Ethernet electrical interfaces. It supports 32K
MAC address entries.
185
5 Boards
Function
The G24TFA provides twenty-four 10M/100M/1000M Ethernet electrical interfaces to
implement data access and line-speed switching.
G24TFA complies with Energy Efficient Ethernet (EEE), so it supports dynamic energy saving
according to network traffic volume.
Application
The G24TFA can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.24.3 Panel
Figure 5-37 shows the appearance of the G24TFA panel.
Figure 5-37 Appearance of the G24TFA panel
1 2
RUN/ALM
Color
Description
RUN/ALM
Green
Issue 05 (2012-12-12)
186
Indicator
ACT/Link
5 Boards
Color
Description
Red
Orange
Green
5.24.4 Interfaces
Table 5-151 describes the types and functions of the interfaces on the G24TFA.
Table 5-151 Types and functions of the interfaces on the G24TFA
Name
Quantity
Description
10M/100M/1000M
BASE-T Ethernet
electrical interface
24
Description
Connector type
RJ45
Compliance
standard
Frame format
Network protocol
IP
187
5 Boards
Specification
Dimensions (depth
x width x height)
Maximum power
consumption
32 W
Weight
2.20 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.25.1 Introduction
The 12-port 10GE optical interface card (SA, SFP+) is called X12SA for short. The X12SA
features high interface density, providing 12 10GE interfaces.
Application
An X12SA board can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
NOTE
Wire-speed forwarding can be implemented regardless of which LPU slot on the S9303&S9303E and
S9306&S9306E is used. Wire-speed forwarding can be implemented only when LPU slots 6 and 7 on the
S9312 are used.
5.25.3 Panel
Figure 5-38 shows the appearance of the X12SA panel.
Issue 05 (2012-12-12)
188
5 Boards
Color
Meaning
RUN/ALM
Green
Red
Orange
ACT
Amber
LINk
Green-yellow
5.25.4 Interfaces
Table 5-155 describes the types and functions of the interfaces on the X12SA.
Issue 05 (2012-12-12)
189
5 Boards
Quantity
Description
12
Description
Connector type
LC/PC
Optical interface
attribute
Depending on the SFP optical module. For details about the attributes of
the optical module, see Table 5-157.
Compliance
standard
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attribute
Description
Transmission
distance
300 m
10 km
40 km
Center
wavelength
850 nm
1310 nm
1550 nm
Transmitting
power
Receiver
sensitivity
-11.1 dBm
-12.6 dBm
-14.1 dBm
Overload
optical power
-1.0 dBm
0.5 dBm
-1.0 dBm
Extinction ratio
3 dB
3.5 dB
3 dB
Fiber type
Multi-mode
Single-mode
190
5 Boards
Specification
Board dimensions
(depth x width x
height)
Power
consumption
85 W
Weight
2.30 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.26.1 Introduction
The 4-port 10GE optical interface line card (XFP) of the S9300&S9300E is called X4UX and
has the following models: (ED, XFP), (EA, XFP) and (EC, XFP).
Table 5-159 lists the board full names and MAC address table capacities.
Table 5-159 X4UX models
Issue 05 (2012-12-12)
Full Name
Short Name
MAC Address
Table Capacity
X4UXA
32K
X4UXC
128K
X4UXD
512K
191
5 Boards
Application
The X4UX can be installed in any LPU slot on the S9312&S9312E, S9306&S9306E, or
S9303&S9303E.
5.26.3 Panel
Figure 5-39 shows the appearance of the X4UX panel.
Figure 5-39 Appearance of the panel of the X4UX
Color
Description
RUN/ALM
Green
Issue 05 (2012-12-12)
Red
Orange
192
5 Boards
Indicator/Button
Color
Description
ACT
Amber
LINK
Green-yellow
5.26.4 Interfaces
Table 5-161 describes the types and functions of the interfaces on the X4UX.
Table 5-161 Types and functions of the interfaces on the X4UX
Name
Quantity
Description
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
193
5 Boards
Description
Transmissio
n distance
300 m
10 km
40 km
80 km
Center
wavelength
850 nm
1310 nm
1550 nm
1550 nm
Transmittin
g power
0 dBm to 4 dBm
Receiver
sensitivity
-7.5 dBm
-11.0 dBm
-15.0 dBm
-24.0 dBm
Overload
optical
power
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Extinction
ratio
3.0 dB
6.0 dB
8.2 dB
9.0 dB
Fiber type
Multi-mode
Single-mode
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
70 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-21.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
194
5 Boards
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1529.5
5 nm
1530.3
3 nm
1531.1
2 nm
1531.9
0 nm
1532.6
8 nm
1533.4
7 nm
1534.2
5 nm
1535.0
4 nm
1548.5
1 nm
1549.3
2 nm
1550.1
2 nm
1550.9
2 nm
1551.7
2 nm
1552.5
2 nm
1553.3
3 nm
1554.1
3 nm
Transmit
optical
power
Receiver
sensitivit
y
-24.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
X4UXA: 64 W
X4UXC: 75 W
X4UXD: 76 W
Weight
X4UXA: 2.16 kg
X4UXC: 2.28 kg
X4UXD: 2.30 kg
Long-term
temperature
Issue 05 (2012-12-12)
0C to 45C
195
5 Boards
Item
Specification
Short-term
temperature
-5C to 55C
5.27.1 Introduction
The 2-port 10GE optical interface line card (XFP) of the S9300&S9300E is called X2UX and
has the following models: (EA, XFP) and (EC, XFP).
Table 5-167 lists the board full names and MAC address table capacities.
Table 5-167 X2UX models
Full Name
Short Name
MAC Address
Table Capacity
X2UXA
32K
X2UXC
128K
Application
X2UX can be installed in any LPU slot of the S9312&S9312E, S9306&S9306E, and
S9303&S9303E.
5.27.3 Panel
Figure 5-40 shows the appearance of an X2UX panel.
Issue 05 (2012-12-12)
196
5 Boards
Color
Description
RUN/ALM
Green
Red
Orange
ACT
Amber
LINK
Green-yellow
5.27.4 Interfaces
Table 5-169 describes the types and functions of the interfaces on the X2UX.
Table 5-169 Types and functions of the interfaces on the X2UX
Issue 05 (2012-12-12)
Name
Quantity
Description
197
5 Boards
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attribute
Description
Transmissio
n distance
300 m
10 km
40 km
80 km
Center
wavelength
850 nm
1310 nm
1550 nm
1550 nm
Transmittin
g power
0 dBm to 4 dBm
Receiver
sensitivity
-7.5 dBm
-11.0 dBm
-15.0 dBm
-24.0 dBm
Overload
optical
power
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Extinction
ratio
3.0 dB
6.0 dB
8.2 dB
9.0 dB
Fiber type
Multi-mode
Single-mode
198
5 Boards
Description
Transmis
sion
distance
70 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-21.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1529.5
5 nm
1530.3
3 nm
1531.1
2 nm
1531.9
0 nm
1532.6
8 nm
1533.4
7 nm
1534.2
5 nm
1535.0
4 nm
1548.5
1 nm
1549.3
2 nm
1550.1
2 nm
1550.9
2 nm
1551.7
2 nm
1552.5
2 nm
1553.3
3 nm
1554.1
3 nm
Transmit
optical
power
Receiver
sensitivit
y
-24.0 dBm
Overload
optical
power
-9.0 dBm
199
5 Boards
Attribut
e
Description
Extinctio
n ratio
8.2 dB
Specification
Board dimensions
(depth x width x
height)
Maximum power
consumption
X2UXA: 52 W
Weight
X2UXA: 2.14 kg
X2UXC: 61 W
X2UXC: 2.26 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.28.1 Introduction
The 8-port 10GE optical interface line card (ED, SFP+) of the S9300E is called
LE2D2X08SED0/LE2D2X08SED1 and provides 8 10GE interfaces. It supports 512K MAC
address entries.
NOTE
LE2D2X08SED1 has gained the FCC certificate, but LE2D2X08SED0 has not.
Issue 05 (2012-12-12)
200
5 Boards
Application
An LE2D2X08SED0 board can be installed in any LPU slot of the S9312E, S9306E, or
S9303E.
5.28.3 Panel
Figure 5-41 shows the appearance of an LE2D2X08SED0/LE2D2X08SED1 panel.
Figure 5-41 Appearance of an LE2D2X08SED0/LE2D2X08SED1 panel
Color
Description
RUN/ALM
Green
Red
Issue 05 (2012-12-12)
201
5 Boards
Indicator/Button
Color
Description
Orange
ACT
Amber
Link
Green-yellow
5.28.4 Interfaces
Table 5-176 describes the types and functions of interfaces on anLE2D2X08SED0/
LE2D2X08SED1 board.
Table 5-176 Types and functions of interfaces on an LE2D2X08SED0/LE2D2X08SED1 board
Interface
Quantity
Description
10GE BASE-SFP+/
1000M BASE-X optical
interface
Description
Connector
LC
Optical interface
attribute
Determined by the SFP+ optical module. For details about the optional
optical module attributes, see Table 5-178.
Standards
compliance
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
202
5 Boards
Description
Transmis
sion
distance
220 m
300 m
10 km
40 km
80 km
Center
waveleng
th
1310 nm
850 nm
1310 nm
1550 nm
1550 nm
Transmitt
ing
power
-6.5 dBm to
-0.5 dBm
-7.3 dBm to
-1 dBm
-8.2 dBm to
0.5 dBm
-4.7 dBm to
4.0 dBm
0 dBm to 4
dBm
Receiver
sensitivit
y
-6.5 dBm
-11.1 dBm
-12.6 dBm
-14.1 dBm
-24.0 dBm
Overload
optical
power
1.5 dBm
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Extinctio
n ratio
3.5 dB
3 dB
3.5 dB
3 dB
9 dB
Fiber
type
Multi-mode
Multi-mode
Single-mode
Modal
bandwidth
and fiber
diameter:
Modal
bandwidth:
2000 Mkm
l 500 Mkm,
62.5 um
Fiber
diameter: 50
um
l 500 Mkm,
62.5 um,
OM1
l 500 Mkm,
50 um,
OM2
l 500 Mkm,
50 um,
OM3
Issue 05 (2012-12-12)
203
5 Boards
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
204
5 Boards
Description
Dimensions (H x
W x D)
Maximum power
consumption
200 W
Weight
2.80 kg
Long-term
operating
temperature
0C to 45C
Short-term
operating
temperature
-5C to 55C
5.29.1 Introduction
The WAN card of the S9300 is called WMNPA.
As an LPU, the WMNPA provides the following types of interfaces by using subcards:
l
155 Mbit/s POS optical interfaces (in compliance with T1 and E1 standards)
NOTE
l When using the WMNPA, insert the CKM into the MPU. If the S9300 uses two MPUs, the CKMs
must be installed on both the MPUs.
l When using the WMNPA, insert at least one subcard; otherwise, the WMNPA does not function
properly.
l The WMNPA does not support hot swapping of subcards.
The WMNPA provides two subcard slots. Different types of subcards can be inserted into one
WMNPA. Table 5-181 provides the names, port quantities, and types of three types of subcards.
Issue 05 (2012-12-12)
205
5 Boards
Port Quantity
P1UF
P4HF
P4CF
Application
A WMNPA board can be installed in any LPU slot of the S9312, S9306, and S9303.
NOTE
5.29.3 Panel
Figure 5-42 shows the appearance of the WMNPA panel.
Figure 5-42 Appearance of the WMNPA panel
1
RUN/ALM
1. Subcard
206
5 Boards
Color
Description
RUN/ALM
Green
STATUS
Red
Orange
Green-yellow
ACT
Amber
LINK
Green-yellow
Specification
Dimensions (depth
x width x height)
Maximum power
consumption
Weight
Issue 05 (2012-12-12)
207
5 Boards
Item
Specification
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
5.30.1 Introduction
The 4-port OC-3c/STM-1c POS-SFP provides 155 Mbit/s optical interfaces. This subcard is
applicable to the aggregation layer of MPLS networks.
Description
PPP, HDLC
Interface type
SFP
Network management
Application
The 4-port OC-3c/STM-1c POS-SFP is an optional subcard which can be installed on the
WMNPA.
Users can choose to install this subcard according to the service requirement, which improves
service flexibility and expansibility.
5.30.3 Panel
Issue 05 (2012-12-12)
208
5 Boards
FPIC-4OC3-POS
TUS
ST A
L/A
L/A
L/A
L/A
Description
STATUS (green)
If the indicator blinks once every 2s (0.5 Hz), the system is running
properly.
If the indicator blinks once every 0.5s (2 Hz), an alarm is generated.
LINK/ACT
(green)
5.30.4 Interfaces
Table 5-186 describes the types and functions of the interfaces on the 4-port OC-3c/STM-1c
POS-SFP FPIC.
Issue 05 (2012-12-12)
209
5 Boards
Table 5-186 Types and functions of the interfaces on the 4-port OC-3c/STM-1c POS-SFP
Name
Qua
ntity
Description
OC-3c/STM-1c
POS-SFP optical
interface
Description
Connector type
LC/PC
Optical
interface
attribute
Depending on the SFP optical module. For details about the attributes of
the optical module, see Table 5-188.
Operation
mode
Full duplex
Link protocol
PPP, HDLC
Network
protocol
IP
Issue 05 (2012-12-12)
Attribute
Description
Transmission
distance
2 km
15 km
40 km
80 km
Center
wavelength
1310 nm
1310 nm
1310 nm
1550 nm
Minimum
transmitting
power
-19.0 dBm
-15.0 dBm
-5.0 dBm
-5.0 dBm
Maximum
transmitting
power
-14.0 dBm
-8.0 dBm
0 dBm
0 dBm
210
5 Boards
Attribute
Description
Receiver
sensitivity
-30.0 dBm
-31.0 dBm
-37.0 dBm
-37.0 dBm
Overload
optical power
-14.0 dBm
-8.0 dBm
-10.0 dBm
-10.0 dBm
Fiber type
Multi-mode
Single-mode
Single-mode
Single-mode
Specification
Dimensions
(depth x width x
height)
185 mm x 145 mm x 20 mm
Typical power
consumption
14 W
Weight
0.50 kg
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
Connector type
LC
Heat dissipation
58 BTU/hour
5.31.1 Introduction
The 4-port OC-12c/STM-4c POS-SFP provides 622 Mbit/s optical interfaces. This subcard is
applicable to the aggregation layer of MPLS networks.
211
5 Boards
Function
Table 5-190 describes the functions of the 4-port OC-12c/STM-4c POS-SFP.
Table 5-190 Functions of the 4-port OC-12c/STM-4c POS-SFP FPIC
Function
Description
PPP, HDLC
Interface type
SFP
Network management
Application
The 4-port OC-12c/STM-4c POS-SFP is an optional subcard installed on the WMNPA.
Users can choose to install this subcard according to the service requirement, which improves
service flexibility and expansibility.
5.31.3 Panel
Figure 5-44 shows the appearance of a 4-port OC-12c/STM-4c POS-SFP FPIC panel.
Figure 5-44 Appearance of a 4-port OC-12c/STM-4c POS-SFP FPIC panel
FPIC-4X0C12-POS
TUS
STA
L/A
L/A
L/A
L/A
Issue 05 (2012-12-12)
212
5 Boards
Description
STATUS (green)
If the indicator blinks once every 2s (0.5 Hz), the system is running
properly.
If the indicator blinks once every 0.5s (2 Hz), an alarm is generated.
LINK/ACT
(green)
5.31.4 Interfaces
Table 5-192 describes the types and functions of the interfaces on the 4-port OC-12c/STM-4c
POS-SFP FPIC.
Table 5-192 Types and functions of the interfaces on the 4-port OC-12c/STM-4c POS-SFP FPIC
Name
Qua
ntity
Description
OC-12c/STM-4c
POS-SFP optical
interface
Issue 05 (2012-12-12)
Attribute
Description
Connector type
LC/PC
Optical
interface
attribute
Depending on the SFP optical module. For details about the attributes of
the optical module, see Table 5-194.
Operation
mode
Full duplex
213
5 Boards
Attribute
Description
Link protocol
PPP, HDLC
Network
protocol
IP
Description
Transmission
distance
15 km
40 km
80 km
Center
wavelength
1310 nm
1310 nm
1550 nm
Minimum
transmitting
power
-15.0 dBm
-3.0 dBm
-3.0 dBm
Maximum
transmitting
power
-8 dBm
2.0 dBm
2.0 dBm
Receiver
sensitivity
-31.0 dBm
-30.0 dBm
-30.0 dBm
Overload
optical power
-8.0 dBm
-8.0 dBm
-8.0 dBm
Fiber type
Single-mode
Single-mode
Single-mode
Issue 05 (2012-12-12)
Item
Specification
Dimensions
(depth x width x
height)
185 mm x 145 mm x 20 mm
Typical power
consumption
15 W
Weight
0.50 kg
214
5 Boards
Item
Specification
Long-term
temperature
0C to 45C
Short-term
temperature
-5C to 55C
Connector type
LC
Heat dissipation
65 BTU/hour
5.32.1 Introduction
The 1-port OC-48c/STM-16c POS-SFP provides 2.5 Gbit/s optical interfaces. This subcard is
applicable to the aggregation layer of MPLS networks.
Description
PPP, HDLC
Interface type
SFP
Network management
Application
The 1-port OC-48c/STM-16c POS-SFP is an optional subcard installed on the WMNPA.
Users can choose to install this subcard according to the service requirement, which improves
service flexibility and expansibility.
Issue 05 (2012-12-12)
215
5 Boards
5.32.3 Panel
Figure 5-45 shows the appearance of a 1-port OC-48c/STM-16c POS-SFP FPIC panel.
Figure 5-45 Appearance of a 1-port OC-48c/STM-16c POS-SFP FPIC panel
FPIC-4XOC48-POS
TUS
STA
CT
K/A
LIN
Description
STATUS (green)
If the indicator blinks once every 2s (0.5 Hz), the system is running
properly.
If the indicator blinks once every 0.5s (2 Hz), an alarm is generated.
LINK/ACT
(green)
5.32.4 Interfaces
Table 5-198 describes the types and functions of the interfaces on the 1-port OC-48c/STM-16c
POS-SFP FPIC panel.
Issue 05 (2012-12-12)
216
5 Boards
Qua
ntity
Description
OC-3c/STM-1c
POS-SFP optical
interface
Description
Connector type
LC/PC
Optical interface
attribute
Determined by the selected SFP optical module For details about the
attributes of the optical module, see Table 5-200.
Operation mode
Full duplex
Frame format
PPP, HDLC
Network protocol
IP
Issue 05 (2012-12-12)
Attribute
Description
Transmission
distance
2 km
15 km
40 km
80 km
Center
wavelength
1310 nm
1310 nm
1310 nm
1550 nm
Minimum
transmitting
power
-10.0 dBm
-5.0 dBm
-2.0 dBm
-2.0 dBm
Maximum
transmitting
power
-3.0 dBm
0 dBm
3.0 dBm
3.0 dBm
Receiver
sensitivity
-21.0 dBm
-21.0 dBm
-30.0 dBm
-30.0 dBm
Overload
optical power
-3.0 dBm
0 dBm
-9.0 dBm
-9.0 dBm
217
5 Boards
Attribute
Description
Fiber type
Single-mode
Single-mode
Single-mode
Single-mode
Issue 05 (2012-12-12)
Item
Specification
185 mm x 145 mm x 20 mm
Typical power
consumption
12 W
Weight
0.5 kg
Long-term temperature
0C to 45C
Short-term temperature
-5C to 55C
Connector type
LC
Heat dissipation
49 BTU/hour
218
6 Cables
Cables
Issue 05 (2012-12-12)
219
6 Cables
6.1.1 Introduction
The power cables of the S9300&S9300E include power cables in the cabinet and power cables
out of the cabinet. The external power cables connect the power distribution cabinet to the power
distribution box, and the internal power cables connect the power distribution box to the
S9300&S9300E in the cabinet.
The internal DC power cables include a -48 V power cable and a power ground cable RTN. One
end of an internal DC power cable is an OT terminal (S9300) or dual OT terminals (S9300E),
which connects to the power supply. The other end is a cord end terminal, which connects to the
power distribution box.
The external DC power cables include a -48 V power cable and a power ground cable RTN. One
end of an external DC cable is an OT terminal, which connects to the power distribution box.
The other end is generally an OT terminal, which connects to the power distribution cabinet.
6.1.2 Structure
Figure 6-1 and Figure 6-2 show the internal DC power cable that connects the power distribution
box to the DC power supplies in the chassis.
Figure 6-1 Internal DC power cable for S9300
Issue 05 (2012-12-12)
220
6 Cables
The terminals of the external DC power cable are determined according to the site survey.
Specification
Terminal connecting to
the power modules of the
S9300
Terminal connecting to
the power distribution
box
Issue 05 (2012-12-12)
Item
Specification
221
6 Cables
Item
Specification
Terminal connecting to
the power modules of the
S9300E
Terminal connecting to
the power distribution
box
Description
Less than
1600 W
Power
distance
35.6 m
55.6 m
77.8 m
Crosssectional
area of
the
conducto
r
16 mm^2
25 mm^2
35 mm^2
Power
cable
Electronic and
electrical
cable-227IEC02
(RV)-16 mm^2(blue, black, red, or
green-yellow)
Electronic and
electrical
cable-227IEC02
(RV)-25 mm^2(blue, black, red, or
green-yellow)
Electronic and
electrical
cable-227IEC02
(RV)-35 mm^2(blue, black, red, or
green-yellow)
Terminal
16 mm^2 power
cable terminal
25 mm^2 power
cable terminal
35 mm^2 power
cable terminal
Power
distance
23.7 m
37.0 m
51.8 m
Crosssectional
area of
the
conducto
r
16 mm^2
25 mm^2
35 mm^2
Less than
2400 W
Issue 05 (2012-12-12)
222
Total
Power
Consum
ption
Less than
3200 W
6 Cables
Description
Power
cable
Electronic and
electrical
cable-227IEC02
(RV)-16 mm^2(blue, black, red, or
green-yellow)
Electronic and
electrical
cable-227IEC02
(RV)-25 mm^2(blue, black, red, or
green-yellow)
Electronic and
electrical
cable-227IEC02
(RV)-35 mm^2(blue, black, red, or
green-yellow)
Terminal
16 mm^2 power
cable terminal
25 mm^2 power
cable terminal
35 mm^2 power
cable terminal
Power
distance
27.7 m
38.8 m
Crosssectional
area of
the
conducto
r
25 mm^2
35 mm^2
Power
cable
Electronic and
electrical
cable-227IEC02
(RV)-25 mm^2(blue, black, red, or
green-yellow)
Electronic and
electrical
cable-227IEC02
(RV)-35 mm^2(blue, black, red, or
green-yellow)
Terminal
25 mm^2 power
cable terminal
35 mm^2 power
cable terminal
Table 6-4 External DC power cables in different cabinet configuration schemes of S9300E
Description
Issue 05 (2012-12-12)
Crosssectional
area of the
conductor
16 mm^2
25 mm^2
35 mm^2
Power
distance
18.8 m
29.4 m
Power
cable
Electronic and
electrical
cable-227IEC02
(RV)-35 mm^2-(blue,
dark, red, yellowgreen)
223
6 Cables
Description
Terminal
OptiX 155/622-16mm^2
power cable terminal
6.2.1 Introduction
The power cables of the S9300&S9300E include:
l
l
An external power cable transmit power from the user's power distribution frame to the power
distribution box in the cabinet, and then an internal power cable transmits power from the power
distribution box to the S9300&S9300E in the cabinet.
Internal power cables are classified into:
l
l
Each internal or external AC power cable consists of the live wire, neutral wire, and ground
cable.
6.2.2 Structure
NOTE
The appearances of the power cables for 800 W power supply unit and 2200 W power supply unit are the
same, but the connectors of the cables are different:
l The power cables for the 800 W power supply units use the C13-straight-female connectors.
l The power cables for the 2200 W power supply units use the C19-straight-female connectors.
Issue 05 (2012-12-12)
224
6 Cables
The terminals of the external AC power cables are determined according to the site survey.
Description
Power cable
Connector
C13-straight-female
Color
Black
Cable length
3 meters
3*1.0 mm2
Cable type
Table 6-6 Technical specifications of the power cables for 2200 W AC power supply units
Item
Description
Power cable
Connector
C19-straight-female
Color
Black
Cable length
3 meters
Cable type
Table 6-7 Technical specifications of the AC power cables out of the cabinet
Issue 05 (2012-12-12)
Item
Description
Power cable
Electronic and electrical cable-300 V-227IEC10(BVV)-6 mm^2Black jacket (core: blue, brown, yellow/green)-36 A-3 cores with
equal cross sections
Terminal
225
6 Cables
6.3.1 Introduction
The ground cables connect the S9300&S9300E and cabinet to the ground. The ground cables in
the front, rear, and side panels of the cabinet have been properly connected before delivery.
6.3.2 Structure
The appearance of ground cable terminals and the DC power cable terminals is the same.
Specification
Cable
Terminal
6.4.1 Introduction
The Console cable is used to connect the S9300&S9300E Console port to the serial port of the
Console to transmit the configuration data of the S9300&S9300E.
You can select the shielded cable or unshielded cable according to the actual situation. One end
of the cable is an RJ45 connector that is connected to the Console port of the main control board,
and the other end that is connected to the serial port of the computer has a DB9 connector and
a DB25 connector. Either of the two connectors can be selected to connect to the serial port
according to the actual situation.
6.4.2 Structure
Figure 6-4 shows the Console cable, and Table 6-9 shows the connection of the Console cable.
Issue 05 (2012-12-12)
226
6 Cables
W1
1. Direction A
2. DB25 plug
3. Label
5. Direction B
6. Direction C
7. DB9 plug
Direction
DB25
DB9
Signal
--->
--->
--->
GND
GND
<---
<---
20
<---
Issue 05 (2012-12-12)
Item
Specification
Connector
X1
227
6 Cables
Item
Specification
Connector
X2
Connector
X3
Fireresistance
CM
6.5.1 Introduction
Ethernet cables are classified into the straight-through cable and the crossover cable.
Straight-through Cable
The straight-through cable is used to connect the Ethernet interfaces between the following
devices:
l
PC and hub
Crossover Cable
The crossover cable is used to connect the Ethernet interfaces between the following devices:
l
Router and PC
PC and PC
6.5.2 Structure
The straight-through cable and the crossover cable are standard unshielded network cables. They
adopt the RJ45 connectors, and Figure 6-5 shows the structure of an RJ45 connector.
Issue 05 (2012-12-12)
228
6 Cables
Table 6-11 describes pin assignments of the straight-through cable. Table 6-12 describes pin
assignments of the crossover cable.
Table 6-11 Pin assignments of the straight-through cable
Connector
X1
Connector X2
Color
Relation
X1.2
X2.2
Orange
Pair
X1.1
X2.1
White/Orange
X1.6
X2.6
Green
X1.3
X2.3
White/Green
X1.4
X2.4
Blue
X1.5
X2.5
White/Blue
X1.8
X2.8
Brown
X1.7
X2.7
White/Brown
Pair
Pair
Pair
Issue 05 (2012-12-12)
Connector
X1
Connector X2
Color
Relation
X1.6
X2.2
Orange
Pair
X1.3
X2.1
White/Orange
X1.2
X2.6
Green
X1.1
X2.3
White/Green
X1.4
X2.4
Blue
X1.5
X2.5
White/Blue
X1.8
X2.8
Brown
Pair
Pair
Pair
229
6 Cables
Connector
X1
Connector X2
Color
X1.7
X2.7
White/Brown
Relation
Specification
Connector
X1/X2
Power cable
Number of
cores
8 cores
Fireresistance
CM
Length
5 m, 10 m, 20 m, or 30m
Specification
Connector
X1/X2
Power cable
Number of
cores
8 cores
Fireresistance
CM
Length
5 m or 30 m
230
6 Cables
6.6.1 Introduction
Optical fibers are classified into single-mode and multimode fibers.
Single-mode fibers have a diameter of 5-10 um and transmit laser in one mode under a specified
wavelength. These fibers support a wide frequency band and a large transmission capacity, so
they are used for long-distance transmission. Most single-mode fibers are yellow.
Multimode fibers have a diameter of 50 um or 62.5 um and transmit laser in multiple modes
under a specified wavelength. These fibers have a lower transmission capacity than single-mode
fibers and are used for short-distance transmission. Most multimode fibers are orange. Table
6-15 shows parameters of multimode fibers.
Table 6-15 Parameters of multimode fibers
Transmission
speed (Gbit/s)
Maximum
Transmission
Distance (m)
Modal
Bandwidth
(MHz x km)
Diameter
(um)
Class
0.1
2000
62.5/125
500
400
50/125
10
300
2000
50/125
220
500
62.5/125
62.5/125
OM1
50/125
OM2
50/125
OM3
Table 6-16 provides the types of optical fibers used by the S9300&S9300E.
Table 6-16 Types of the optical fibers
Issue 05 (2012-12-12)
No.
Local
Connector
Remote
Connector
Cables
LC/PC
FC/PC
Single mode
LC/PC
LC/PC
Single mode/
multimode
LC/PC
SC/PC or LC/
PC
Single mode/
multimode
231
6 Cables
NOTE
CAUTION
The plugging/unplugging of the LC/PC optical interface needs only an axial operation instead
of a rotation. The operation procedures and precautions are as follows:
l Align the head of the fiber jumper with the optical interface on the optical board and exert
proper force to push the fiber inside.
l Press the clip before pulling out the fiber. Push in the fiber connector inward slightly, and
then pull out the connector.
Issue 05 (2012-12-12)
232
6 Cables
Specification
Fiber
transmission
mode
Single mode/multimode
Connector
LC/PC
Outer diameter
2 mm
6.7.1 Introduction
The external synchronization interface of the S9300&S9300E is used for clock and time
synchronization.
The S9300&S9300E can be connected to the external clock source or clock source device
through the clock cable.
The clock cable is used to connect the S9300&S9300E with the clock interface of the external
equipment. With the cable, the S9300&S9300E can receive 2-channel 2.048 MHz or 2.048 Mbit/
s synchronous clock signals provided by the upstream device. The S9300&S9300E can also
offer 2-channel 2.048 MHz or 2.048 Mbit/s synchronous clock signals to the downstream device.
When the S9300&S9300E is connected to the clock interface of the external equipment through
the clock cable, the S9300&S9300E can receive the 2-channel TOD or DCLS synchronous clock
signals provided by the upstream device. The S9300&S9300E can also offer 2-channel TOD or
DCLS synchronous clock signals to the downstream device.
One end of the clock cable is the RJ45 connector, which is connected to the BITTS interface on
the SRU or MCU of the S9300&S9300E. The other end of the clock cable is connected to the
external clock device. The connector type depends on the type of the external clock device. The
external clock device connected to the S9300&S9300E can be the SubMiniature version B
(SMB) clock source, Boyonet Neil Councilman (BNC) clock source, RJ45 clock source, and
RJ45 time source.
Figure 6-7 Clock cable connections
S9300 clock
interface
Cable 1
Cable 2
Transmultiplexer
RJ45 interface
Issue 05 (2012-12-12)
SMB interface
External clock
device
SMB/BNC/RJ45
interface
233
6 Cables
According to the functions and interface types of the external clock device connected to the
S9300&S9300E, the following cables can be selected:
l
If the connected device is the clock source and the RJ45 interface is used:
Cable 1 can be the RJ48 cable. The transmultiplexer or cable 2 is not required.
If the connected device is the clock source and the SMB interface is used:
Cable 1 can be the RJ45 cable, and cable 2 can be the SMB/SMB trunk cable. The
transmultiplexer is required.
If the connected device is the clock source and the SMB interface is used:
Cable 1 can be the RJ45 cable, and cable 2 can be the SMB/SMB trunk cable. The
transmultiplexer is required.
If the connected device is the time source and the RJ45 interface is used:
Cable 1 can be the RJ45 cable. The transmultiplexer or cable 2 is not required.
NOTE
Both the RJ48 cables and RJ45 cables must be shielded cables.
6.7.2 Structure
RJ48 Cable
The RJ48 cable supported by the S9300&S9300E is the 120 trunk cable (shielded cable), as
shown in Figure 6-8.
Figure 6-8 Structure of the 120 trunk cable
NOTE
When the connected device is RJ45 clock source, the RJ48 cables are used for the connection of
S9300&S9300E and the RJ45 clock source.
RJ45 Cable
The RJ45 cable supported by the S9300&S9300E is the straight-through cable (shielded cable),
as shown in Figure 6-9.
Figure 6-9 Structure of the straight-through cable
Issue 05 (2012-12-12)
234
6 Cables
NOTE
When the connected device is RJ45 time source, the RJ45 cables is used for the connection of
S9300&S9300E and the RJ45 time source.
When the connected device is SMB clock source or BNC clock source, the RJ45 cable is used for the
connection of S9300&S9300E and transmultiplexer.
Issue 05 (2012-12-12)
Cable Description
Length
3m
15 m
30 m
60 m
80 m
235
6 Cables
Straight-Through Cable
Cable Description
Length
0.2 m
0.5 m
1m
1.5 m
Single cable-straight-through cable-2.00 m-(8-bit network interface-I)(CC4P0.5 gray)-(8-bit network interface-I), DL3470
2m
3m
Single cable-straight-through cable-5.00 m-(8-bit network interface-I)(CC4P0.5 gray)-(8-bit network interface-I), DL4538
5m
Single cable-straight-through cable-10.00 m-(8-bit network interface-I)(CC4P0.5 gray)-(8-bit network interface-I), DL2761
10 m
Single cable-straight-through cable-30.00 m-(8-bit network interface-I)(CC4P0.5 gray)-(8-bit network interface-I), DL4217
30 m
40 m
Issue 05 (2012-12-12)
236
6 Cables
6.8.1 Introduction
An S9300 can use QSFP high-speed cables or QSFP+ optical fibers as stack cables, which
interconnect the interfaces on the VSTSA cards. The S9306 and S9312 switches are connected
through the stack cables to form a logical switch, implementing packet forwarding.
NOTE
The two ends of a stack cable must be covered by the ESD caps.
The Quad Small Form-Factor Pluggable (QSFP) is a 4-channel small hot pluggable optical module.
Currently, the S9300E does not support stacking.
6.8.2 Structure
Figure 6-12 and Figure 6-13 show the structures of the QSFP high-speed stack cables.
Figure 6-12 QSFP high-speed stack cable structure (1)
Issue 05 (2012-12-12)
Item
Description
Cable
Connector X1/X2
QSFP-38PIN-male
Fire-resistance
237
6 Cables
Item
Description
Color
Black or Blue
Number of cores
Length
10 m
Bend radius
75 mm
Table 6-19 lists the technical specifications of a QSFP+ optical fiber used on the S9300.
Table 6-19 Technical specifications of a QSFP+ optical fiber
Issue 05 (2012-12-12)
Fiber type
OM3
OM4
Length
100 m
150 m
238
7 List of Indicators
List of Indicators
Issue 05 (2012-12-12)
239
7 List of Indicators
Color
Description
RUN/ALM
Green
Red
Color
Description
ALM
Red
INPUT
Green
Issue 05 (2012-12-12)
240
7 List of Indicators
Color
Description
RUN
Green
ALM
Yellow
FAULT
Red
Color
Description
RUN
Green
ALM
Yellow
FAULT
Red
Issue 05 (2012-12-12)
241
7 List of Indicators
Color
Meaning
RUN/ALM
Green
ACT
Red
Orange
Green
RST
SYNC
Green
242
7 List of Indicators
Color
Description
RUN/ALM
Green
ACT
Red
Orange
Green
RST
SYNC
Green
Issue 05 (2012-12-12)
243
7 List of Indicators
Color
Description
RUN/ALM
Green
Red
Orange
Color
Description
ACT
Amber
LINK
Green-yellow
Issue 05 (2012-12-12)
244
7 List of Indicators
Color
Description
LINK/ACT
Green
Color
Description
RUN/ALM
Green
Red
ACT
Green
Issue 05 (2012-12-12)
245
8 List of Boards
List of Boards
Issue 05 (2012-12-12)
246
8 List of Boards
LPUs are classified into S series boards, E series boards, F series boards, B series boards, and POS
boards:
l
S series boards are SA boards, for example, 24-port 100M/1000M Ethernet optical LPU (SA,
SFP)-32K MAC address entries.
E series boards include EA, EC, and ED boards, for example, 48-port 100M Ethernet optical LPU
(EA, SFP)-32K MAC address entries.
F series boards include FA and FC boards, for example, 48-port 1000M Ethernet electrical LPU
(FA, RJ45)-32K MAC address entries.
B series boards are BC boards, for example, 48-port 100M/1000M Ethernet optical LPU (BC,
SFP)-128K MAC address entries.
A POS board consists of a WAN card and subcard such as P4CF, P4HF, or P1UF.
Description
FCC
Com
plia
nce
SRUA
Main control board applied to the S9312 and S9306. The unidirectional
switching capacity is 256 Gbit/s.
Yes
SRUB
Main control board applied to the S9312 and S9306. The unidirectional
switching capacity is 512 Gbit/s.
Yes
MCUA
Yes
FSUA
Yes
VSTSA
Stack interface flexible pluggable card on the SRU, used to provide the
switch stacking function.
Yes
CKMA
Yes
Issue 05 (2012-12-12)
Name
Description
FCC
Com
plia
nce
LE2D2SR
UDC00
No
247
8 List of Boards
Name
Description
FCC
Com
plia
nce
LE2D2SR
UDC01
Yes
MCUA
Yes
CKMA
Yes
Description
FCC
Com
plia
nce
CMUA
Yes
Description
FCC
Com
plia
nce
VAMPA
Yes
Issue 05 (2012-12-12)
Name
Description
FCC
Com
plia
nce
G24CA
Yes
G24SA
Yes
X12SA
No
G48SA
Yes
248
Issue 05 (2012-12-12)
8 List of Boards
Name
Description
FCC
Com
plia
nce
G48SC
Yes
G48SD
Yes
G48SBC
Yes
G48SFA
Yes
F48SA
Yes
F48SC
Yes
G48TA
Yes
G48TC
Yes
G48TD
Yes
G48TBC
Yes
G48TFA
Yes
G48CEAT
Yes
G48VA
Yes
F48TA
Yes
F48TC
Yes
F48TFA
Yes
249
8 List of Boards
Name
Description
FCC
Com
plia
nce
LE0DX40
SFC00
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
LE2D2X4
0SFC1
Yes
LE0DX16
SFC00
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
Issue 05 (2012-12-12)
LE2D2X1
6SFC1
Yes
S24XA
Yes
S24XC
Yes
T24XA
Yes
250
8 List of Boards
Name
Description
FCC
Com
plia
nce
G24CEAS
Yes
G24SC
Yes
G24SD
Yes
G24TFA
Yes
X4UXA
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
X4UXC
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
Issue 05 (2012-12-12)
251
8 List of Boards
Name
Description
FCC
Com
plia
nce
X4UXD
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
X2UXA
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
Issue 05 (2012-12-12)
252
8 List of Boards
Name
Description
FCC
Com
plia
nce
X2UXC
l S
9
3
0
0:
Y
es
l S
9
3
0
0
E
:
N
o
LE2D2X0
8SED0
8-port 10GE optical interface line card (ED, SFP+)-512K MAC address
entries
No
LE2D2X0
8SED1
8-port 10GE optical interface line card (ED, SFP+)-512K MAC address
entries
Yes
Issue 05 (2012-12-12)
Name
Description
FCC
Com
plia
nce
WMNPA
Yes
P4CF
Yes
P4HF
Yes
P1UF
Yes
253
8 List of Boards
NOTE
l The S9300E does not support the value-added service card VAMPA , G48VA or POS interface
card.The S9300 does not support the LE2D2X08SED0/LE2D2X08SED1, LE2D2X16SFC1 and
LE2D2X40SFC1.
l The Small Form-factor pluggable (SFP) is a hot pluggable optical module.
l The 10 Gigabit Small Form-Factor Pluggable (XFP) is a 10G hot pluggable optical module.
l The 10 Gigabit Small Form-Factor Pluggable (SFP+) is a 10G hot pluggable optical module. Its caliber
is smaller than the caliber of the XFP optical module.
l By default, the transmission rate of an optical interface is 1000 Mbit/s and the 100M/1000M autonegotiation is not supported. To use 100 Mbit/s optical interfaces, you must configure it manually.
l The boards gaining the FCC certificate must be used together with the chassis gaining the FCC
certificate.
Issue 05 (2012-12-12)
Board
Maximum Power
Consumption
Weight
LE0MSRUA
81 W (including FSUA)
2.80 kg
LE0MMCUA
18 W
0.90 kg
LE0DMCUA
26 W (including CKMA)
0.92 kg
LE0D00SRUB0
0
2.90 kg
CMUA
1W
0.22 kg
LE2D2SRUDC0
0/
LE2D2SRUDC0
1
2.90 kg
VAMPA
120 W
3.1 kg
FSUA
20 W
0.42 kg
VSTSA
12 W
1 kg
G48SA
75 W
2.54 kg
G48SC
92 W
2.66 kg
G48SD
110 W
2.66 kg
G48SBC
185 W
2.90 kg
G48SFA
65 W
2.60 kg
254
Issue 05 (2012-12-12)
8 List of Boards
Board
Maximum Power
Consumption
Weight
G48TA
62 W
2.50 kg
G48TC
68 W
2.62 kg
G48TD
98 W
2.62 kg
G48TBC
160 W
2.90 kg
G48TFA
48 W
2.50 kg
G48CEAT
62 W
2.50 kg
G48VA
2.6 kg
F48SA
64 W
2.54 kg
F48SC
76 W
2.66 kg
F48TA
59 W
2.50 kg
F48TC
70 W
2.62 kg
F48TFA
40 W
2.30 kg
LE0DX40SFC00
/
LE2D2X40SFC1
183 W
2.90 kg
LE0DX16SFC00
/
LE2D2X16SFC1
150 W
2.60 kg
LE2D2X08SED
0/
LE2D2X08SED
1
200 W
2.8 kg
S24XA
65 W
2.4 kg
S24XC
81 W
2.5 kg
G24CEAS
70 W
2.7 kg
G24CA
67 W
2.26 kg
G24SA
45 W
2.22 kg
G24SC
63 W
2.66 kg
G24SD
75 W
2.66 kg
G24TFA
32 W
2.20 kg
T24XA
53 W
2.3 kg
X12SA
85 W
2.3 kg
255
8 List of Boards
Board
Maximum Power
Consumption
Weight
X4UXA
64 W
2.16 kg
X4UXC
75 W
2.28 kg
X4UXD
76 W
2.30 kg
X2UXA
52 W
2.14 kg
X2UXC
61 W
2.26 kg
WMNPA
14 W
0.50 kg
P4HF
15 W
0.50 kg
P1UF
12 W
0.50 kg
NOTE
The S9300E does not support G48VA, VAMPA, or POS boards.The S9300 does not support the
LE2D2X08SED0/LE2D2X08SED1, LE2D2X16SFC1 and LE2D2X40SFC1.
Issue 05 (2012-12-12)
256
Issue 05 (2012-12-12)
257
Description
Connector type
RJ45
Compliance
standard
IEEE 802.3ab
Frame format
Network protocol
IP
l The SFP+ and the XFP are 10G hot-pluggable optical modules. Compared with the XFP, the SFP+ has
smaller width.
l The 10G SFP+ and XFP optical modules support LAN access and WAN access functions.
Description
Connector type
LC/PC
Optical interface
attribute
Depending on the SFP+ or XFP optical module. For details about the
attributes of the optical module, see Table 9-3 and Table 9-4.
Compliance
standard
IEEE 802.3ae
Frame format
Network protocol IP
Issue 05 (2012-12-12)
258
Description
Transmis
sion
distance
220 m
300 m
10 km
40 km
80 km
Center
waveleng
th
1310 nm
850 nm
1310 nm
1550 nm
1550 nm
Transmitt
ing
power
-6.5 dBm to
-0.5 dBm
-7.3 dBm to
-1 dBm
-8.2 dBm to
0.5 dBm
-4.7 dBm to
4.0 dBm
0 dBm to 4
dBm
Receiver
sensitivit
y
-6.5 dBm
-11.1 dBm
-12.6 dBm
-14.1 dBm
-24.0 dBm
Overload
optical
power
1.5 dBm
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Extinctio
n ratio
3.5 dB
3 dB
3.5 dB
3 dB
9 dB
Fiber
type
Multi-mode
Multi-mode
Single-mode
Modal
bandwidth
and fiber
diameter:
Modal
bandwidth:
2000 Mkm
l 500 Mkm,
62.5 um
Fiber
diameter: 50
um
l 500 Mkm,
62.5 um,
OM1
l 500 Mkm,
50 um,
OM2
l 500 Mkm,
50 um,
OM3
Issue 05 (2012-12-12)
Attribute
Description
Transmissio
n distance
300 m
10 km
40 km
80 km
259
Attribute
Description
Center
wavelength
850 nm
1310 nm
1550 nm
1550 nm
Transmittin
g power
0 dBm to 4 dBm
Receiver
sensitivity
-7.5 dBm
-11.0 dBm
-15.0 dBm
-24.0 dBm
Overload
optical
power
-1.0 dBm
0.5 dBm
-1.0 dBm
-7.0 dBm
Fiber type
Multi-mode
Single-mode
Modal
bandwidth: 2000
Mkm
Fiber diameter:
50 um
NOTE
Only Huawei certified optical modules can be installed on the S9300&S9300E. The non-certified optical
modules are unreliable and may affect services. Huawei will not be responbsible for fixing the issues caused
by non-certified optical modules.
All the optical modules listed in the documentation are Huawei certified optical modules.
Description
Connector type
LC/PC
Optical interface
attribute
Compliance
standard
IEEE 802.3z
Frame format
Network protocol IP
Issue 05 (2012-12-12)
260
Description
Tran
smiss
ion
dista
nce
500 m
10 km
10 km (singlemode bidirectional
fiber)
40 km
40 km
80 km
100 km
Cent
er
wave
lengt
h
850 nm
1310
nm
Tx:
1310
nm
Tx:
1490
nm
1310
nm
1550
nm
1550
nm
1550
nm
Rx:
1490
nm
Rx:
1310
nm
Tran
smitt
ing
powe
r
-9.5
dBm to
-2.5
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-9.0
dBm to
-3.0
dBm
-5.0
dBm to
0 dBm
-5.0
dBm to
0 dBm
-2.0
dBm to
5.0
dBm
0 dBm
to 5
dBm
Rece
iver
sensi
tivity
-17.0
dBm
-20.0
dBm
-19.5
dBm
-19.5
dBm
-23
dBm
-22
dBm
-23.0
dBm
-30.0
dBm
Over
load
optic
al
powe
r
0 dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-3.0
dBm
-9.0
dBm
Extin
ction
ratio
9 dB
9 dB
6 dB
6 dB
9 dB
8.5 dB
9 dB
8 dB
Fiber
type
Multimode
Single-mode
Modal
bandwi
dth:
400Mk
m
Fiber
diamete
r: 50 um
Issue 05 (2012-12-12)
261
Description
Connector
RJ45
Standards
compliance
IEEE802.3ab
Frame format
Network protocol
IP
NOTE
Only Huawei certified optical modules can be installed on the S9300&S9300E. The non-certified optical
modules are unreliable and may affect services. Huawei will not be responbsible for fixing the issues caused
by non-certified optical modules.
All the optical modules listed in the documentation are Huawei certified optical modules.
Description
Connector type
LC/PC
Optical interface
attribute
Depending on the SFP optical module. For details about the attributes of
the optical module, see Table 9-9.
Compliance
standard
IEEE 802.3u
Frame format
Network protocol IP
Issue 05 (2012-12-12)
Attrib
ute
Description
Transm
ission
distanc
e
2 km
15 km
15 km (single-mode
bidirectional fiber)
40 km
80 km
262
Attrib
ute
Description
Center
wavele
ngth
1310 nm
Transm
itting
power
-19.0 dBm
to -14.0
dBm
Receiv
er
sensitiv
ity
1310 nm
Tx: 1310
nm
Tx: 1550
nm
1310 nm
1550 nm
Rx: 1550
nm
Rx: 1310
nm
-15.0 dBm
to -8.0
dBm
-15.0 dBm
to -8.0
dBm
-15.0 dBm
to -8.0
dBm
-5.0 dBm
to 0 dBm
-5.0 dBm
to 0 dBm
-30.0 dBm
-31.0 dBm
-32.0 dBm
-32.0 dBm
-37.0 dBm
-37.0 dBm
Overlo
ad
optical
power
-14.0 dBm
-8.0 dBm
-8.0 dBm
-8.0 dBm
-10.0 dBm
-10.0 dBm
Extincti
on ratio
10 dB
8.2 dB
8.5 dB
8.5 dB
10.5 dB
10.5 dB
Fiber
type
Multimode
Single-mode
NOTE
Only Huawei certified optical modules can be installed on the S9300&S9300E. The non-certified optical
modules are unreliable and may affect services. Huawei will not be responbsible for fixing the issues caused
by non-certified optical modules.
All the optical modules listed in the documentation are Huawei certified optical modules.
Issue 05 (2012-12-12)
Attribute
Description
Connector
LC/PC
Optical
interface
attribute
Determined by the SFP optical module. For details about the attributes of
the optional optical module, see Table 9-11, Table 9-12, and Table 9-12.
263
Attribute
Description
Mode
Full duplex
Link protocol
Network
protocol
IP
Description
Transmission
distance
2 km
15 km
40 km
80 km
Center
wavelength
1310 nm
1310 nm
1310 nm
1550 nm
Minimum
transmit
optical power
-19.0 dBm
-15.0 dBm
-5.0 dBm
-5.0 dBm
Maximum
transmit
optical power
-14.0 dBm
-8.0 dBm
0 dBm
0 dBm
Receiver
sensitivity
-30.0 dBm
-31.0 dBm
-37.0 dBm
-37.0 dBm
Overload
optical power
-14.0 dBm
-8.0 dBm
-10.0 dBm
-10.0 dBm
Optical fiber
type
Multi-mode
Single-mode
Single-mode
Single-mode
Issue 05 (2012-12-12)
Attribute
Description
Transmission
distance
15 km
40 km
80 km
Center
wavelength
1310 nm
1310 nm
1550 nm
Minimum
transmit
optical power
-15.0 dBm
-3.0 dBm
-3.0 dBm
Maximum
transmit
optical power
-8 dBm
2.0 dBm
2.0 dBm
264
Attribute
Description
Receiver
sensitivity
-31.0 dBm
-30.0 dBm
-30.0 dBm
Overload
optical power
-8.0 dBm
-8.0 dBm
-8.0 dBm
Optical fiber
type
Single-mode
Single-mode
Single-mode
Description
Transmission
distance
2 km
15 km
40 km
80 km
Center
wavelength
1310 nm
1310 nm
1310 nm
1550 nm
Minimum
transmit
optical power
-10.0 dBm
-5.0 dBm
-2.0 dBm
-2.0 dBm
Maximum
transmit
optical power
-3.0 dBm
0 dBm
3.0 dBm
3.0 dBm
Receiver
sensitivity
-21.0 dBm
-21.0 dBm
-30.0 dBm
-30.0 dBm
Overload
optical power
-3.0 dBm
0 dBm
-9.0 dBm
-9.0 dBm
Optical fiber
type
Single-mode
Single-mode
Single-mode
Single-mode
NOTE
Only Huawei certified optical modules can be installed on the S9300&S9300E. The non-certified optical
modules are unreliable and may affect services. Huawei will not be responbsible for fixing the issues caused
by non-certified optical modules.
All the optical modules listed in the documentation are Huawei certified optical modules.
Issue 05 (2012-12-12)
265
Table 9-14 Attributes of an ESFP-CWDM optical module (100 Mbit/s or 1000 Mbit/s)
Attribut
e
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.5 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
1591
nm
1611
nm
1591
nm
1611
nm
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
70 km
Center
waveleng
th
1471
nm
Transmit
optical
power
Receiver
sensitivit
y
-21.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
1491
nm
1511
nm
1531
nm
1551
nm
1571
nm
266
Table 9-16 and Table 9-17 list attributes of the DWDM optical module.
Table 9-16 Attributes of an ESFP-DWDM optical module (100 Mbit/s or 1000 Mbit/s)
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
120 km
Center
waveleng
th
1529.5
5 nm
1533.4
7 nm
1537.4
0 nm
1541.3
5 nm
1545.3
2 nm
1549.3
2 nm
1553.3
3 nm
1557.3
6 nm
1530.3
3 nm
1534.2
5 nm
1538.1
9 nm
1542.1
4 nm
1546.1
2 nm
1550.1
2 nm
1554.1
3 nm
1558.1
7 nm
1531.1
2 nm
1535.0
4 nm
1538.9
8 nm
1542.9
4 nm
1546.9
2 nm
1550.9
2 nm
1554.9
4 nm
1558.9
8 nm
1531.9
0 nm
1535.8
2 nm
1539.7
7 nm
1543.7
3 nm
1547.7
2 nm
1551.7
2 nm
1555.7
5 nm
1559.7
9 nm
1532.6
8 nm
1536.6
1 nm
1540.5
6 nm
1544.5
3 nm
1548.5
1 nm
1552.5
2 nm
1556.5
6 nm
1560.6
1 nm
Transmit
optical
power
Receiver
sensitivit
y
-28.0 dBm
Overload
optical
power
-8.0 dBm
Extinctio
n ratio
8.2 dB
Operatin
g
temperat
ure
0C to 45C
267
Description
Transmis
sion
distance
80 km
Center
waveleng
th
1529.5
5 nm
1530.3
3 nm
1531.1
2 nm
1531.9
0 nm
1532.6
8 nm
1533.4
7 nm
1534.2
5 nm
1535.0
4 nm
1548.5
1 nm
1549.3
2 nm
1550.1
2 nm
1550.9
2 nm
1551.7
2 nm
1552.5
2 nm
1553.3
3 nm
1554.1
3 nm
Transmit
optical
power
Receiver
sensitivit
y
-24.0 dBm
Overload
optical
power
-9.0 dBm
Extinctio
n ratio
8.2 dB
NOTE
Only Huawei certified optical modules can be installed on the S9300&S9300E. The non-certified optical
modules are unreliable and may affect services. Huawei will not be responbsible for fixing the issues caused
by non-certified optical modules.
All the optical modules listed in the documentation are Huawei certified optical modules.
Issue 05 (2012-12-12)
Attribut
e
Description
Transmis
sion
distance
150 m
268
Attribut
e
Description
Center
waveleng
th
850 nm
Transmit
power
Receiver
sensitivit
y
-5.4 dBm
Extinctio
n ratio
3 dB
Fiber type
Connecto
r type
MPO
NOTE
Only Huawei certified optical modules can be installed on the S9300&S9300E. The non-certified optical
modules are unreliable and may affect services. Huawei will not be responbsible for fixing the issues caused
by non-certified optical modules.
Issue 05 (2012-12-12)
269