Académique Documents
Professionnel Documents
Culture Documents
DOCUMENT FEEDER
(Machine Code: A663)
SPECIFICATIONS
31 March 1997
1. SPECIFICATIONS
The specifications are the same as for the A548 ARDF (DF61).
Original Size and Weight: Thick original mode (default mode)
Use this setting for normal paper types
Maximum A3, 11" x 17"
Minimum B6, 51/2" x 81/2"
Weight
52 ~ 128 g/m2 (14 ~ 34 lb)
Thin original mode
Maximum A3, 11" x 17"
Minimum B6 (sideways), 51/2" x 81/2"
Weight
40 ~ 128 g/m2 (11 ~ 34 lb)
Auto reverse mode
Maximum A3, 11" x 17"
Minimum B5, 51/2" x 81/2"
Weight
52 ~ 105 (14 ~ 27 lb)
Original Feed:
Original Placement:
Original Separation:
Original Transport:
Power Consumption:
45 W
Power Source:
A663-1
31 March 1997
A663
A548
555 mm/s
505 mm/s
590 ms (thin original mode) 620 ms (thin original mode)
690 ms (thick original mode) 720 ms (thick original mode)
A663-2
Options
INSTALLATION
31 March 1997
Qty
48
31 March 1997
INSTALLATION
Copier
[A]
[B]
A663I500.wmf
[E] [D]
A663I501.wmf
[E]
[I]
[H]
[F]
[C]
[G]
A663I502.wmf
A663I503.wmf
CAUTION
Unplug the copier power cord before starting the following procedure.
1. Remove the strips of tape [A].
2. Attach the sponge retainer [B] to the top cover of the copier as shown.
3. Tighten the two stud screws [C].
4. Mount the ARDF by aligning the holes [D] in the ARDF and the stud
screws [C], then slide the ARDF to the front as shown.
NOTE: When mounting the ARDF, hold it by hand as shown in the
illustration. Holding it in another way may damage the ARDF.
5. Screw the two stud screws [E] into the holes [F] and tighten them.
6. Connect the connectors [G] into the socket on the rear of the copier.
7. Attach the symbol explanation decal [H] and the combine originals
explanation decal [I] to the ARDF as shown (except for the A207 copier).
49
22 March 1996
6.2
INSTALLATION
INSTALLATION PROCEDURE
[A]
[A]
[B]
A548I500.wmf
[E]
A548I501.wmf
[E]
[D]
[I]
[H]
[F]
[G]
[C]
A548I502.wmf
A548I503.wmf
I CAUTION
Unplug the copier power cord before starting the following procedure.
1. Remove the strips of tape [A].
2. Attach the sponge retainer [B] to the top cover of the copier as shown.
3. Tighten the two stud screws [C].
17
Auto Reverse
Document
Feeder
4. Mount the ARDF by aligning the holes [D] in the ARDF and the stud
screws [C], then slide the ARDF to the front as shown.
3
4
5
6
7
17
16
15
9
10
11
12
13
14
A663S500.wmf
Description
Original Set Sensor (S1)
Feed-in Cover Open Sensor (S2)
Stopper Solenoid (SOL1)
Ready Lamp (L1)
Auto Lamp (L2)
Feed-in Motor (M1)
Belt Drive Motor (M2)
DF Main Board (PCB1)
Inverter Solenoid (SOL2)
Feed-out Cover Open Sensor (S3)
Feed-out Motor (M3)
Feed-out Sensor (S4)
APS Start Sensor (S5)
DF Position Sensor (S6)
Original Width Sensor-1 (S7)
Original Width Sensor-2 (S8)
Original Width Sensor-3 (S9)
Registration Sensor (S10)
Index No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
P to P Location
B2
E2
J16
D2
C2
D17
F17
F11
K16
J2
H17
I2
L2
K2
H2
G2
F2
A2