Académique Documents
Professionnel Documents
Culture Documents
This test report consists of 63 pages in total. It may be duplicated completely for legal use with the
approval of the applicant. It should not be reproduced except in full, without the written approval of
our laboratory. The client should not use it to claim product endorsement by CNLA, NVLAP, A2LA or
any government agencies. The test results in the report only apply to the tested sample. The test
results in this report are traceable to the national or international standards.
0536
ILAC MRA
No. 2177-01
Table of Contents
1
2
2.1
3
3.1
3.2
3.3
3.4
4
4.1
4.1.1
4.1.2
4.1.3
4.1.4
4.1.5
4.1.6
4.1.7
4.2
4.2.1
4.2.2
4.2.3
4.2.4
4.2.5
4.2.6
4.2.7
4.3
4.3.1
4.3.2
4.3.3
4.3.4
4.3.5
4.3.6
4.4
4.4.1
4.4.2
4.4.3
4.4.4
4.4.5
4.4.6
5
5.1
5.2
5.3
5.4
5.5
CERTIFICATION..............................................................................................4
SUMMARY OF TEST RESULTS .....................................................................6
MEASUREMENT UNCERTAINTY...................................................................7
GENERAL INFORMATION ..............................................................................8
GENERAL DESCRIPTION OF EUT ................................................................8
GENERAL DESCRIPTION OF APPLIED STANDARDS..................................9
DESCRIPTION OF SUPPORT UNITS ..........................................................10
CONFIGURATION OF SYSTEM UNDER TEST ...........................................10
EMISSION TEST ........................................................................................... 11
CONDUCTED EMISSION MEASUREMENT................................................. 11
LIMITS OF CONDUCTED EMISSION MEASUREMENT .............................. 11
TEST INSTRUMENTS................................................................................... 11
TEST PROCEDURE......................................................................................12
DEVIATION FROM TEST STANDARD..........................................................12
TEST SETUP.................................................................................................12
EUT OPERATING CONDITIONS ..................................................................13
TEST RESULTS ............................................................................................14
RADIATED EMISSION MEASUREMENT......................................................16
LIMITS OF RADIATED EMISSION MEASUREMENT ...................................16
TEST INSTRUMENTS...................................................................................16
TEST PROCEDURE......................................................................................17
DEVIATION FROM TEST STANDARD..........................................................17
TEST SETUP.................................................................................................18
EUT OPERATING CONDITIONS ..................................................................18
TEST RESULTS ............................................................................................19
HARMONICS CURRENT MEASUREMENT..................................................21
LIMITS OF HARMONICS CURRENT MEASUREMENT ...............................21
TEST INSTRUMENTS...................................................................................21
TEST PROCEDURE......................................................................................22
TEST SETUP.................................................................................................22
EUT OPERATING CONDITIONS ..................................................................23
TEST RESULTS ............................................................................................24
VOLTAGE FLUCTUATION AND FLICKER MEASUREMENT .......................25
LIMITS OF VOLTAGE FLUCTUATION AND FLICKER MEASUREMENT.....25
TEST INSTRUMENTS...................................................................................25
TEST PROCEDURE......................................................................................25
TEST SETUP.................................................................................................26
EUT OPERATING CONDITIONS ..................................................................26
TEST RESULTS ............................................................................................27
IMMUNITY TEST ...........................................................................................28
GENERAL DESCRIPTION ............................................................................28
GENERAL PERFORMANCE CRITERIA DESCRIPTION ..............................29
PARTICULAR PERFORMANCE CRITERIA DESCRIPTION FOR LAN
FUNCTION OF EUT ......................................................................................30
EUT OPERATING CONDITION.....................................................................30
ELECTROSTATIC DISCHARGE IMMUNITY TEST (ESD) ............................31
5.5.1
5.5.2
5.5.3
5.5.4
5.5.5
5.6
5.6.1
5.6.2
5.6.3
5.6.4
5.6.5
5.7
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
5.8
5.8.1
5.8.2
5.8.3
5.8.4
5.8.5
5.9
5.9.1
5.9.2
5.9.3
5.9.4
5.9.5
5.10
5.10.1
5.10.2
5.10.3
5.10.4
5.10.5
5.11
5.11.1
5.11.2
5.11.3
5.11.4
5.11.5
6
7
1 CERTIFICATION
Reference No.:930203H01
PRODUCT:
BRAND NAME:
MODEL NO:
TESTED:
TEST ITEM:
APPLICANT:
STANDARDS:
Network Camera
Vivotek, WiSOL, Afreey, LevelOne
IP3135, WiCAM-3135, ANC-600V, FCS-1030
Nov. 22 to Dec. 09, 2004
ENGINEERING SAMPLE
VIVOTEK INC.
EN 55022:1994+A1:1995
+A2:1997, Class B
EN 61000-3-2: 2000, Class A
(see note * below)
EN 61000-3-3: 1995+A1: 2001
EN 55024:1998+A1:2001
+A2:2003
IEC 61000-4-2:2001
IEC 61000-4-3:2002+A1:2002
IEC 61000-4-4:1995+A1:2000
+A2:2001
IEC 61000-4-5:2001
IEC 61000-4-6:2001
IEC 61000-4-8:2001
IEC 61000-4-11:2001
The above equipment (Model: IP3135) has been tested by Advance Data
Technology Corporation, and found compliance with the requirement of the
above standards.
CERTIFICATION - Continued
The test record, data evaluation & Equipment Under Test (EUT) configurations
represented herein are true and accurate accounts of the measurements of the
samples EMC characteristics under the conditions specified in this report.
PREPARED BY
DATE:
DATE:
DATE:
DATE:
( Midoli Peng )
TECHNICAL
ACCEPTANCE
Responsible for RF
TECHNICAL
ACCEPTANCE
(Hank Chung )
APPROVED BY
( Ivan Peng )
:
( Eric Lin, Manager )
Note *: The power consumption of EUT is 7.019W, which is less than 75W and no limits apply.
Therefore it is deemed to comply with EN 61000-3-2: 2000 without any testing.
EMISSION
Test Type
Result
Conducted Test
PASS
Radiated Test
PASS
EN61000-3-2:2000,
Class A
Harmonic current
emissions
PASS
EN61000-3-3:1995 +
A1:2001
PASS
EN55022:1994+A1:
1995+A2:1997,
Class B
Remarks
Meets Class B Limit
Minimum passing margin is
-3.03 dB at 2.138 MHz
Meets Class B Limit
Minimum passing margin is
-3.8 dB at 800.00 MHz
The power consumption of
EUT is less than 75W and no
limits apply
Meets the requirements.
PASS
PASS
PASS
PASS
PASS
PASS
PASS
Value
Conducted emissions
2.53 dB
2.98 dB
GENERAL INFORMATION
Network Camera
MODEL NO.
NA
DATA CABLE
NA
I/O PORT
RJ-45 port x1
NOTE:
1. The EUT has four model names and brand names, which are identical to
each other in all aspects except for the followings:
Brand Name
Model Name
Vivotek
IP3135
WiSOL
WiCAM-3135
Afreey
ANC-600V
LevelOne
FCS-1030
From the above models, model: IP3135 was selected as representative
model for the test and its data was recorded in this report.
2. The EUT must be supplied with a power adapter and following different
models could be chosen:
Brand
Model No.
Spec.
JENTEC
JTA0302D-E
JENTEC
JTA0302D-C
JENTEC
JTA0302D-D
The above adapters are the same, except for the plug shape. The model:
JTA0302D-E was selected as representative model for the test and its data
was recorded in this report.
EN 55024:1998+A1:2001
+A2:2003
IEC 61000-4-2:2001
IEC 61000-4-3:2002+A1:2002
IEC 61000-4-4:1995+A1:2000
+A2:2001
IEC 61000-4-5:2001
IEC 61000-4-6:2001
IEC 61000-4-8:2001
IEC 61000-4-11:2001
All tests have been performed and recorded as per the above standards.
3.3
The EUT has been tested as an independent unit together with other necessary
accessories or support units. The following support units or accessories were used to
form a representative test configuration during the tests.
No. Product
1 NOTEBOOK
COMPUTER
Brand
Model No.
DELL
PP01L
Serial No.
FCC ID
TW-09C74812800-1A3-1999
FCC DoC
TEST TABLE
1. Notebook
Computer
CONTROL ROOM
10
EMISSION TEST
Class A (dBuV)
Quasi-peak Average
79
66
73
60
73
60
Class B (dBuV)
Quasi-peak Average
66 - 56
56 - 46
56
46
60
50
CALIBRATED
MODEL NO.
SERIAL NO.
ESCS 30
847124/029
ESHS-Z5
848773/004
KNW-407
8/1395/12
RF Cable (JETBAO)
RG233/U
Cable_CA_01
Terminator(for KYORITSU)
50
Software
Cond-V2e
NA
NA
MANUFACTURER
ROHDE & SCHWARZ
UNTIL
Test Receiver
ROHDE & SCHWARZ LISN
(for EUT)
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in ADT Shielded Room No. A.
3. The VCCI Con A Registration No. is C-817.
11
G ro u n d P la n e
40cm
EUT
80cm
L IS N
H o riz o n ta l R e f e r e n c e
G r o u n d P la n e
N o te : 1 .S u p p o r t u n its w e r e c o n n e c te d t o s e c o n d L IS N .
2 .B o th o f L IS N s ( A M N ) a r e 8 0 c m f ro m E U T a n d a t le a s t 8 0
fr o m o th e r u n its a n d o th e r m e ta l p la n e s
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
12
13
Network Camera
MODEL
IP3135
230Vac, 50 Hz
6dB BANDWIDTH
9 kHz
PHASE
Line (L)
Freq.
Corr.
Reading Value
[MHz]
0.189
0.443
0.630
2.138
17.174
29.117
Factor
(dB)
0.31
0.34
0.36
0.55
1.64
1.94
[dB (uV)]
Q.P.
AV.
46.73
40.12
38.94
45.48 42.42
36.16
32.66
-
No
1
2
3
4
5
6
Rex Huang
Emission
Level
[dB (uV)]
Q.P.
AV.
47.04
40.46
39.30
46.03 42.97
37.80
34.60
-
Limit
Margin
[dB (uV)]
Q.P.
AV.
64.08 54.08
57.01 47.01
56.00 46.00
56.00 46.00
60.00 50.00
60.00 50.00
(dB)
Q.P.
AV.
-17.04
-16.55
-16.70
-9.97
-3.03
-22.20
-25.40
-
REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. "-": The Quasi-peak reading value also meets average limit and
measurement with the average detector is unnecessary.
3. The emission levels of other frequencies were very low against the limit.
4. Margin value = Emission level - Limit value
5. Correction factor = Insertion loss + Cable loss
6. Emission Level = Correction Factor + Reading Value.
14
EUT
INPUT POWER
(SYSTEM)
Network Camera
MODEL
IP3135
230Vac, 50 Hz
6dB BANDWIDTH
9 kHz
PHASE
Neutral (N)
Freq.
Corr.
Reading Value
[MHz]
0.189
0.439
0.693
2.138
16.781
29.234
Factor
(dB)
0.31
0.34
0.37
0.55
1.49
1.66
[dB (uV)]
Q.P.
AV.
45.16
38.93
36.97
42.06
36.49
32.64
-
No
1
2
3
4
5
6
Rex Huang
Emission
Level
[dB (uV)]
Q.P.
AV.
45.47
39.27
37.34
42.61
37.98
34.30
-
Limit
Margin
[dB (uV)]
Q.P.
AV.
64.08 54.08
57.08 47.08
56.00 46.00
56.00 46.00
60.00 50.00
60.00 50.00
(dB)
Q.P.
-18.61
-17.81
-18.66
-13.39
-22.02
-25.70
AV.
-
REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually.
2. "-": The Quasi-peak reading value also meets average limit and
measurement with the average detector is unnecessary.
3. The emission levels of other frequencies were very low against the limit.
4. Margin value = Emission level - Limit value
5. Correction factor = Insertion loss + Cable loss
6. Emission Level = Correction Factor + Reading Value.
15
MODEL NO.
SERIAL NO.
8594E
R3271A
3710A04861
85060311
CALIBRATED
UNTIL
Sep. 23, 2005
Jun. 29, 2005
CPA9232
8449B
1057
3008A01922
ESCS30
100287
VULB9168
138
BBHA9120
BBHA 9170
D124
BBHA9170192
UHAP
897
VHAP
880
CS-201
SF102
1565157
22054-2
STCCAB-30M1GHz-021
NA
9913-30M
Software
AS60P8
NA
CHANCE MOST
AT-100
0203
NA
Antenna Tower
CHANCE MOST Turn Table
TT-100
0203
NA
Note: 1. The calibration interval of the above test instruments is 12 months (36 months for
Tunable Dipole Antenna)and the calibrations are traceable to NML/ROC and
NIST/USA.
2. The horn antenna and HP preamplifier (model: 8449B) are used only for the
measurement of emission frequency above 1GHz if tested.
3. The test was performed in ADT Open Site No. C.
4. The FCC Site Registration No. is 656396.
5. The VCCI Site Registration No. is R-1626.
6. The CANADA Site Registration No. is IC 4824-3.
16
17
1-4m
Variable
10m
Turn Table
80cm
Ground Plane
Test Receiver
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
18
Network Camera
MODEL
IP3135
230Vac, 50 Hz
FREQUENCY
RANGE
30-1000 MHz
DETECTOR
FUNCTION&
BANDWIDTH
Quasi-Peak,
120kHz
Stanly Lin
Freq.
(MHz)
1
2
3
4
5
6
7
8
9
10
200.00
250.21
280.00
300.00
350.01
400.02
500.00
800.00
900.00
1000.00
REMARKS:
Emission
Level
(dBuV/m)
24.50 QP
29.60 QP
29.70 QP
27.00 QP
29.60 QP
30.90 QP
30.60 QP
32.20 QP
30.00 QP
30.10 QP
Limit
(dBuV/m)
Margin
(dB)
30.00
37.00
37.00
37.00
37.00
37.00
37.00
37.00
37.00
37.00
-5.50
-7.40
-7.30
-10.00
-7.40
-6.10
-6.40
-4.80
-7.00
-6.90
Antenna
Height
(m)
4.00 H
4.00 H
4.00 H
4.00 H
3.21 H
2.33 H
2.39 H
1.00 H
1.00 H
1.00 H
Table
Angle
(Degree)
111
238
20
66
111
64
87
191
309
145
Raw
Value
(dBuV)
13.30
16.40
15.20
11.80
12.90
12.80
9.70
6.00
2.00
1.60
Correction
Factor
(dB/m)
11.20
13.20
14.50
15.20
16.70
18.10
20.90
26.20
28.00
28.50
19
EUT
INPUT POWER
(SYSTEM)
Network Camera
MODEL
IP3135
230Vac, 50 Hz
FREQUENCY
RANGE
30-1000 MHz
DETECTOR
FUNCTION&
BANDWIDTH
Quasi-Peak,
120kHz
Stanly Lin
Freq.
(MHz)
1
2
3
4
5
6
7
8
9
10
11
36.05
200.00
250.02
257.50
280.00
350.03
400.00
499.97
800.00
900.00
999.95
REMARKS:
Emission
Level
(dBuV/m)
21.40 QP
26.00 QP
28.40 QP
29.90 QP
31.80 QP
26.40 QP
31.80 QP
28.70 QP
33.20 QP
31.80 QP
31.60 QP
Limit
(dBuV/m)
Margin
(dB)
30.00
30.00
37.00
37.00
37.00
37.00
37.00
37.00
37.00
37.00
37.00
-8.60
-4.00
-8.60
-7.10
-5.20
-10.60
-5.20
-8.30
-3.80
-5.20
-5.40
Antenna
Height
(m)
1.00 V
1.00 V
1.00 V
1.00 V
1.00 V
1.10 V
1.09 V
3.49 V
2.03 V
1.99 V
1.97 V
Table
Angle
(Degree)
20
147
245
269
64
24
245
102
3
143
155
Raw
Value
(dBuV)
8.80
14.80
15.20
16.10
17.30
9.70
13.70
7.80
7.00
3.80
3.10
Correction
Factor
(dB/m)
12.60
11.20
13.20
13.80
14.50
16.70
18.10
20.90
26.20
28.00
28.50
20
4.3
Harmonics
Order
n
3
5
7
9
11
13
15<=n<=39
Model No.
HAR1000
Serial No.
086
Calibrated Until
Jan. 12, 2005
21
Measuring System
AC Power Source
EUT
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
22
23
Network Camera
MODEL
IP3135
FUNDAMENTAL
VOLTAGE/AMPERE
229.7 Vrms /
0.073 Arms
POWER
FREQUENCY
50.301 Hz
POWER
CONSUMPTION
7.019 W
POWER FACTOR
0.420
ENVIRONMENTAL
CONDITIONS
25 deg. C, 55 % RH,
982 hPa
TESTED BY
Kevin Huang
1. Limits are not specified for equipment with a rated power of 75W or
less (other than lighting equipment).
2. According to EN 61000-3-2: 2000 the manufacturer shall specify the
power of the apparatus. This value shall be used for establishing limits.
The specified power shall be within +/-10% of the measured power.
24
LIMIT
1.0
0.65
NOTE
Pst means short-term flicker indicator.
Plt means long-term flicker indicator.
500
4%
3.3%
Model No.
HAR1000
Serial No.
086
Calibrated Until
Jan. 12, 2005
4.4.3
TEST PROCEDURE
a. The EUT was placed on the top of a wooden table 0.8 meters above the ground
and operated to produce the most unfavorable sequence of voltage changes
under normal operating conditions.
b. During the flick measurement, the measure time shall include that part of whole
operation cycle in which the EUT produce the most unfavorable sequence of
voltage changes. The observation period for short-term flicker indicator is 10
minutes and the observation period for long-term flicker indicator is 2 hours.
25
Measuring System
AC Power Source
EUT
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
26
Network Camera
MODEL
IP3135
FUNDAMENTAL
VOLTAGE/AMPERE
229.7 Vrms /
0.071 Arms
POWER
FREQUENCY
50.301 Hz
OBSERVATION
PERIOD (TP)
10 min.
POWER FACTOR
0.417
ENVIRONMENTAL
CONDITIONS
25 deg. C, 55 % RH,
982 hPa
TESTED BY
Kevin Huang
TEST PARAMETER
MEASUREMENT
VALUE
LIMIT
REMARKS
Pst
0.340
1.00
Pass
Plt
0.342
0.65
Pass
Tdt (ms)
0.00
500
Pass
dmax (%)
0.00
4%
Pass
dc (%)
0.00
3.3%
Pass
NOTE:
(1)
(2)
(3)
(4)
(5)
27
5 IMMUNITY TEST
5.1 GENERAL DESCRIPTION
Product Standard: EN 55024:1998+A1:2001+A2:2003
IEC 61000-4-2 Electrostatic Discharge - ESD:
8kV air discharge, 4kV Contact discharge,
Performance Criterion B
Basic Standard,
Specification, and
Performance
Criteria:
ii)
Voltage Interruptions:
i)
28
29
CRITERION A -
Error rate, request for retry and speed of data transmission rate
may be degraded during the application of the test.
Degradation of the performance as described in criteria A is
CRITERION B permitted provided that the normal operation of the EUT is selfrecoverable to the condition immediately before the application of
the test. In these cases, operator response is permitted to reinitiate an operation.
Degradation of the performance as described in criteria A and B
is permitted provided that the normal operation of the EUT is
CRITERION C self-recoverable to the condition immediately before the
application of the test or can be restored after the test by the
operator.
30
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
ESS-100L(A)
0189C01491
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in ESD room.
31
32
1m
Vertical
coupling plane
0.5mm Isolation Support
ESD
Generator
EUT
470k
X4
Nearest
Wall
80cm
Horizontal
coupling plane
PS
Reference Ground Plane
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
NOTE:
TABLE-TOP EQUIPMENT
The configuration consisted of a wooden table 0.8 meters high standing on the Ground Reference
Plane. The GRP consisted of a sheet of aluminum at least 0.25mm thick, and 2.5 meters square
connected to the protective grounding system. A Horizontal Coupling Plane (1.6m x 0.8m) was placed
on the table and attached to the GRP by means of a cable with 940k total impedance. The equipment
under test, was installed in a representative system as described in section 7 of IEC 61000-4-2, and its
cables were placed on the HCP and isolated by an insulating support of 0.5mm thickness. A distance of
1-meter minimum was provided between the EUT and the walls of the laboratory and any other metallic
structure.
FLOOR-STANDING EQUIPMENT
The equipment under test was installed in a representative system as described in section 7 of IEC
61000-4-2, and its cables were isolated from the Ground Reference Plane by an insulating support of
0.1-meter thickness. The GRP consisted of a sheet of aluminum that is at least 0.25mm thick, and 2.5
meters square connected to the protective grounding system and extended at least 0.5 meters from the
EUT on all sides.
33
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
23 deg. C, 45 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Rock Su
Performance
Criterion
B
B
3. Left side
4. Rear side
NOTES:(1) There was no change compared with initial operation during the test.
(2) The EUT sometimes request time out during the test but selfrecoverable after the test.
* According to the applicant's requirement, metal of RJ-45 connector was only tested
contact discharge.
34
3
2
35
IEC 61000-4-3
80 MHz - 1000 MHz
3 V/m
1kHz Sine Wave, 80%, AM Modulation
1 % of fundamental
Horizontal and Vertical
3m
1.5m
3 seconds
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
757LC
7889-1
NA
60S1G3M1
304334
NA
3141
1050
NA
BBHA9120-D1
D123
4232A-01
93801
SML03
101159
FP6001
30817
AR Power Amplifier
EMCO Bi_Log Antenna
Schwarzbeck
Antenna (Horn)
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in Chamber Room No. B.
36
EUT
RF Amplifier
RF Generator
and
control system
Monitoring
system
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
NOTE:
TABLETOP EQUIPMENT
The EUT installed in a representative system as described in section 7 of IEC 61000-4-3 was placed on
a non-conductive table 0.8 meters in height. The system under test was connected to the power and
signal wire according to relevant installation instructions.
FLOOR STANDING EQUIPMENT
The EUT installed in a representative system as described in section 7 of IEC 61000-4-3 was placed on
a non-conductive wood support 0.1 meters in height. The system under test was connected to the
power and signal wire according to relevant installation instructions.
37
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
23 deg. C, 56 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Kevin Huang
Frequency
(MHz)
Result
Polarity
Azimuth
80 -1000 MHz
80 -1000 MHz
80 -1000 MHz
80 -1000 MHz
PASS
PASS
PASS
PASS
V&H
V&H
V&H
V&H
0
90
180
270
Field
Strength
(V/m)
3
3
3
3
Observation
Performance
Criterion
Note
NOTE: There was no change compared with the initial operation during the test.
38
IEC 61000-4-4
Power Line - 1 kV
Signal/Control Line - 0.5kV
Positive/Negative
5 kHz
5/50 ns
15 ms
300 ms
Not less than 1 min.
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
CE-40
9803223
CE-40-CCL
9712328
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in ESD room.
39
Nearest
Wall
EUT
EFT/B
Generator
and
Coupling/
Decoupling
Network
80cm
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
NOTE:
TABLETOP EQUIPMENT
The configuration consisted of a wooden table (0.8m high) standing on the Ground Reference Plane.
The GRP consisted of a sheet of aluminum (at least 0.25mm thick and 2.5m square) connected to the
protective grounding system. A minimum distance of 0.5m was provided between the EUT and the
walls of the laboratory or any other metallic structure.
FLOOR STANDING EQUIPMENT
The EUT installed in a representative system as described in section 7 of IEC 61000-4-4 and its cables,
were isolated from the Ground Reference Plane by an insulating support that is 0.1-meter thick. The
GRP consisted of a sheet of aluminum (at least 0.25mm thick and 2.5m square) connected to the
protective grounding system.
40
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
23 deg. C, 43 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Kevin Huang
I. POWER PORT
VOLTAGE
TEST POINT
(kV)
L1
1
L2
1
POLARITY
(+/-)
+/+/-
OBSERVATION
Note (1)
Note (1)
PERFORMANCE
CRITERION
A
A
OBSERVATION
PERFORMANCE
CRITERION
Note (1)
NOTES:(1) There was no change compared with the initial operation during the test.
(2) The EUT request time out during the test but self-recoverable after the
test.
41
5.8
IEC 61000-4-5
Combination Wave
1.2/50 us Open Circuit Voltage
8 /20 us Short Circuit Current
Test Voltage:
Power Line - 1 kV
Surge Input/Output:
L1-L2
Generator Source
2 ohm between networks
Impedance:
12 ohm between network and ground
Polarity:
Positive/Negative
Phase Angle (degree): 0 / 90 / 180 / 270
Pulse Repetition Rate: 1 time / min. (maximum)
Number of Tests:
5 positive and 5 negative at selected points
DESCRIPTION &
MANUFACTURER
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
EMC Pro
9712339
KeyTek, Coupler/Decoupler
CM-I/OCD
9908190
NA
KeyTek, Coupler/Decoupler
CM-TELCD
9906197
NA
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in EMS room.
42
EUT
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
43
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
25 deg. C, 53 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Kevin Huang
I. POWER PORT
VOLTAGE
TEST
(kV)
POINT
1
L1-L2
POLARITY
(+/-)
+/-
OBSERVATION
NOTE
PERFORMANCE
CRITERION
A
NOTE: There was no change compared with the initial operation during the test.
44
The EUT request time out during the test but could be self-recoverable
after the test.
IEC 61000-4-6
0.15 MHz - 80 MHz
3 Vr.m.s.
1kHz Sine Wave, 80%, AM Modulation
1 % of fundamental
Power Mains, Unshielded
Signal / Control Line
CDN-M2 (2 wires), CLAMPCDN-T8
3 seconds
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
SMY 01
848027/030
75A250AM1
307297
NA
4230
13302
EM-101
35453
NA
FCC CDN M2
FCC-801-M2-16A
03048
FCC CDN M3
FCC-801-M3-16A
03055
FCC-801-T2
02025
FCC-801-T4
02030
FCC-801-T8
02036
AR Amplifier
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in Chamber Room No. B.
45
EUT
AC Power line
CDN
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
NOTE:
FLOOR-STANDING EQUIPMENT
The equipment to be tested is placed on an insulating support of 0.1 meters height above a ground
reference plane. All relevant cables shall be provided with the appropriate coupling and decoupling
devices at a distance between 0.1 meters and 0.3 meters from the projected geometry of the EUT on
the ground reference plane.
46
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
24 deg. C, 46 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Kevin Huang
Cable
Injection
Method
Observation
Performance
Criterion
AC power line
CDN-M2
Note (1)
Injection
Method
Observation
Performance
Criterion
Clamp
Note (1)
RJ-45 cable
NOTE: (1)There is no change compared with the initial operation during the test.
47
IEC 61000-4-8
50Hz
1 A/m
1 minute
Helmholtz coil, diameter 1.5m
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
4090
NA
HC150-360
NA
NA
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in EMS room.
3. It has been demonstrated with the LAB34 that the test equipment meets the specified
requirements in the standard with at least a 95% confidence.
The power supply, input and output circuits shall be connected to the sources of
power supply, control and signal.
48
EUT
Test Generator
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
NOTE:
TABLETOP EQUIPMENT
The equipment shall be subjected to the test magnetic field by using the induction coil of standard
dimension (1 m x 1 m). The induction coil shall then be rotated by 90 degrees in order to expose the
EUT to the test field with different orientations.
FLOOR-STANDING EQUIPMENT
The equipment shall be subjected to the test magnetic field by using induction coils of suitable
dimensions. The test shall be repeated by moving and shifting the induction coils, in order to test the
whole volume of the EUT for each orthogonal direction. The test shall be repeated with the coil shifted
to different positions along the side of the EUT, in steps corresponding to 50 % of the shortest side of
the coil. The induction coil shall then be rotated by 90 degrees in order to expose the EUT to the test
field with different orientations.
49
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
25 deg. C, 55 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Kevin Huang
DIRECTION
X
Y
Z
RESULTS
PASS
PASS
PASS
OBSERVATION
Note
Note
Note
PERFORMANCE CRITERION
A
A
A
NOTE: There was no change compared with the initial operation during the test.
50
IEC 61000-4-11
Minimum three test events in sequence
Minimum ten seconds
0 / 45 / 90 / 135 / 180 / 225 / 270 / 315
3 times
MODEL NO.
SERIAL NO.
CALIBRATED UNTIL
EMC Pro
9712339
NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are
traceable to NML/ROC and NIST/USA.
2. The test was performed in EMS room.
51
EUT
AC Power Line
For the actual test configuration, please refer to the related item Photographs of the
Test Configuration.
52
Network Camera
MODEL
IP3135
ENVIRONMENTAL
CONDITIONS
25 deg. C, 53 % RH,
982 hPa
INPUT POWER
230Vac, 50 Hz
TESTED BY
Kevin Huang
PERFORMANCE
CRITERION
>95
0.5
PASS
Note (1)
30
25
PASS
Note (1)
>95
250
PASS
Note (2)
NOTES:(1) There was no change compared with initial operation during the test.
(2) The EUT shut down during the test but could be self-recoverable after
the test.
53
54
55
56
ESD TEST
57
RS TEST
58
EFT TEST
59
60
61
POWER-FREQUENCY MAGNETIC
FIELDS TEST
62
63