Vous êtes sur la page 1sur 54

Ministry of Defence

Interim Defence Standard 02-524 Part 1


Issue 2 Publication Date 10 August 2002

Guide to the Selection of Cable Glands in


Submarines
Part 1
Pressure Hull Glands
NOTE
This Standard is Provisional
If you have Difficulty with its Application
Please Advise the Directorate of
Standardization

Category 2

AMENDMENTS ISSUED SINCE PUBLICATION


AMD NO

DATE OF
ISSUE

TEXT AFFECTED

SIGNATURE &
DATE

Revision Note
This Issue of this Standard has been prepared to incorporate changes to text and presentation.
The technical content has been amended.
Historical Record
NES 524 Part 1 Issue 1
NES 524 Part 1 Issue 2
NES 524 Part 1 Issue 3
Def Stan 02-514 Part 1 Issue 1

Nov 1991
Apr 2000

DEFENCE STANDARD 524 (NES 524)

GUIDE TO THE SELECTION OF CABLE GLANDS IN SUBMARINES

PART 1 ISSUE 2

PRESSURE HULL GLANDS

This Defence Standard is


authorized for use in MOD contracts
by the Defence Procurement Agency and
the Defence Logistics Organisation

Published by:
Defence Procurement Agency,
An Executive Agency of The Ministry of Defence,
UK Defence Standardization,
Kentigern House,
65 Brown Street,
Glasgow, G2 8EX.
1

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

SCOPE
1.

All cables fitted outside the hulls of Submarines are to be sheathed with medium density
polyethylene and are to be passed through the pressure hull by suitable moulded polyethylene
glands. Cables with Polychloroprene (PCP) or Chlorosulphonated Polyethylene (CSP) sheaths
are not to be used except when approved by the Ship Support Agency/
Marine Electrical Systems 2 (SSA/MLS2).

2.

The earliest versions of polyethylene hull glands were the screw type fitted to SSK and early
SSN and the flange type fitted to early SSBN. A later development resulted in the introduction
of the spigot (castellated nut) type hull glands which are fitted to Swiftsure, Trafalgar and
Vanguard Classes of Submarines.

3.

All types of moulded polyethylene spigot type hull glands have been included in this Defence
Standard. Also included are multistem glands used on existing sonar systems, but these are
not to be considered for any new service requirement.

4.

Two standards of pressure hull spigot are in current use: Imperial (23/8 in dia, 60.32 mm dia)
for Swiftsure and Trafalgar Classes, and Metric (62.95 mm dia) for Vanguard Class. Glands
in the preferred metric range of Section 4.4 can be supplied with either interface. When
ordering, it is necessary to quote the Service Drawing Number (SDN) for the basic
configuration and the interface type (imperial or metric), and the lengths of outboard and
inboard cable required.

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

FOREWORD
Sponsorship
1.

This Defence Standard is sponsored by the Defence Logistics Organisation (DLO), Ministry
of Defence (MOD).

2.

The complete Standard comprises:


Guide to the Selection of Cable Glands in Submarines:
Part 1:

Pressure Hull Glands;

Part 2:

Pressure Equipment and Disc Seal Glands;

Part 3:

Bulkhead Penetrators and Gland Tubes;

3.

Any user of this Def Stan either within MOD or in industry may propose an amendment to it.
Proposals for amendments that are not directly applicable to a particular contract are to be
made to the publishing authority identified on Page (i), and those directly applicable to a
particular contract are to be dealt with using existing departmental procedures.

4.

If it is found to be unsuitable for any particular requirement, MOD is to be informed in writing


of the circumstances.

5.

No alteration is to be made to this standard except by the issue of an authorized amendment.

6.

Unless otherwise stated, reference in this standard to approval, approved, authorized and
similar terms means by the MOD in writing.

7.

Any significant amendments that may be made to this standard at a later date will be indicated
by a vertical sideline. Deletions will be indicated by 000 appearing at the end of the line
interval.

8.

This Def Stan has been reissued because of Technical Updates.

Conditions of Release
General
9.

This Def Stan has been devised solely for the use of the MOD, and its contractors in the
execution of contracts for the MOD. To the extent permitted by law, the MOD hereby excludes
all liability whatsoever and howsoever arising (including but without limitation, liability
resulting from negligence) for any loss or damage however caused when the standard is used
for any other purpose.

10.

This document is Crown Copyright and the information herein may be subject to Crown or
third party rights. It is not to be released, reproduced or published without written permission
of the MOD.

11.

The Crown reserves the right to amend or modify the contents of this standard without
consulting or informing any holder.

MOD Tender or Contract Process


12.

This Def Stan is the property of the Crown. Unless otherwise authorized in writing by the
MOD it must be returned on completion of the contract, or submission of the tender, in
connection with which it is issued.

13.

When this standard is used in connection with a MOD tender or contract, the user is to ensure
that he is in possession of the appropriate version of each document, including related
documents, relevant to each particular tender or contract. Enquiries in this connection may
be made to the authority named in the tender or contract.

14.

When standard are incorporated into MOD contracts, users are responsible for their correct
application and for complying with contractual and any other statutory requirements.
Compliance with an Def Stan does not of itself confer immunity from legal obligations.

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Categories of Naval Defence Standard


15.

The Category of this Naval Defence has been determined using the following criteria:
a.

Category 1. If not applied may have a Critical affect on the following:


Safety of the vessel, its complement or third parties.
Operational performance of the vessel, its systems or equipment.

b.

Category 2. If not applied may have a Significant affect on the following:


Safety of the vessel, its complement or third parties.
Operational performance of the vessel, its systems or equipment.
Through life costs and support.

c.

Category 3. If not applied may have a Minor affect on the following:


MOD best practice and fleet commonality.
Corporate Experience and Knowledge.
Current support practice.

Related Documents
16.

In the tender and procurement processes the related documents listed in each section and
Annex A can be obtained as follows:
a.

British Standards

British Standards Institution,


389 Chiswick High Road,
London, W4 4AL.

b.

Defence Standards, including

Defence Procurement Agency,


An Executive of The Ministry of Defence,
UK Defence Standardization,
Kentigern House,
65 Brown Street,
Glasgow, G2 8EX.

c.

Other documents

Tender or Contract Sponsor to advise.

17.

All applications to Ministry Establishments for related documents are to quote the relevant
MOD Invitation to Tender or Contract number and date, together with the sponsoring
Directorate and the Tender or Contract Sponsor.

18.

Prime Contractors are responsible for supplying their subcontractors with relevant
documentation, including specifications, standards and drawings.

Health and Safety


Warning
19.

This Defence Standard may call for the use of processes, substances and/or procedures that
may be injurious to health if adequate precautions are not taken. It refers only to technical
suitability and in no way absolves either the supplier or the user from statutory obligations
relating to health and safety at any stage of manufacture or use. Where attention is drawn to
hazards, those quoted may not necessarily be exhaustive.

20.

This Def Stan has been written, and is to be used, taking into account the policy stipulated in
JSP430 MOD Ship Safety Management System Handbook.

Additional Information
(There is no relevant information included)

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

CONTENTS
Page No
TITLE PAGE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
SCOPE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
FOREWORD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Sponsorship

............................................................... 3

Conditions of Release . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Categories of NES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Health and Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Additional Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
SECTION

1.

PERFORMANCE SPECIFICATION . . . . . . . . . . . . . . . . . . . 8

SECTION

2.

NATIONAL/INTERNATIONAL REGULATIONS . . . . . . . . 8

SECTION

3.

MILITARY STANDARDS/REQUIREMENTS . . . . . . . . . . . . 8

SECTION

4.
4.1
Figure 4.1

DESIGN REQUIREMENTS/GUIDANCE . . . . . . . . . . . . . . . 8
Imperial Spigot Type (Castellated) Hull Glands . . . . . . . . . . . 8
Gland and Cable Assembly Spigot Type, 1 Screened Quad,
(Type F) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Gland and Cable Assembly Spigot Type, 4 Way, (Type G) . . 10
Gland and Cable Assembly Spigot Type, 6 Screened Pairs,
(Type B) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Gland and Cable Assembly Spigot Type, 8 Pair, (Type A) . . 12
Gland and Cable Assembly Spigot Type, 4 Coaxial 75 Ohms,
(Type C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Gland and Cable Assembly Spigot Type, 4 Coaxial 50 Ohms,
(Type C) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Gland and Cable Assembly, Spigot Type, 4 Coaxial
50 Ohms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Gland and Cable Assembly, Spigot Type,
1 Screened Pair + 1 x 3 Core (Type H) . . . . . . . . . . . . . . . . . . 16
Gland and Cable Assembly, Spigot Type, 19 Screened Pair . 17
Gland and Cable Assembly, Spigot Type, 19 Screened Pair . 18

Figure 4.2
Figure 4.3
Figure 4.4
Figure 4.5
Figure 4.6
Figure 4.7
Figure 4.8
Figure 4.9
Figure 4.10

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Page No
Figure 4.11
Figure 4.12
4.2
Figure 4.13
Figure 4.14
Figure 4.15
4.3
Figure 4.16
Figure 4.17
Figure 4.18
Figure 4.19
Figure 4.20
Figure 4.21
Figure 4.22
Figure 4.23
4.4
Figure 4.24
Figure 4.25
Figure 4.26
Figure 4.27
Figure 4.28
Figure 4.29
Figure 4.30
Figure 4.31
Figure 4.32
Figure 4.33

Gland and Cable Assembly, Spigot Type, 19 x 3


Core Screened . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type, 19 Screened Pair .
Multi-Stem Glands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly Multi-Stem Type, 30 Pair . . . . .
Gland and Cable Assembly Multi-Stem Type, 60 Pair . . . . .
Gland and Cable Assembly Multi-Stem Type, 60 Pair . . . . .
Special Hull Glands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly Spigot Type J . . . . . . . . . . . . . . .
Gland and Cable Assembly Spigot Type (SPM) . . . . . . . . . .
Gland and Cable Assembly Spigot Type, 19 Quad . . . . . . . .
Gland and Cable Assembly Spigot Type, 45 Quad . . . . . . . .
Gland and Cable Assembly Spigot Type, 4 x 6 Core . . . . . . .
Gland and Cable Assembly Flange Type, 14 Core . . . . . . . .
Gland Flange Type, AWJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland, AWJ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metric Spigot Type Pressure Hull Glands . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric, 4 Coaxial
50 Ohms (Type 11) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
19 Screened Pair (Type 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
19 Screened Pair (Type 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
19 Screened Pair (Type 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
19 Screened Triple (Type 5) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
3 x 3 Screened Pair (Type 7) . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
1 Triple (Type 8) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric, 19 Pair . . .
Gland and Cable Assembly, Spigot Type Metric,
1 x 52 Quad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gland and Cable Assembly, Spigot Type Metric,
4 Single Core . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Page No
SECTION

5.

CORPORATE EXPERIENCE & KNOWLEDGE . . . . . . . . 45

ANNEX

A.

RELATED DOCUMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

ANNEX

B.

ABBREVIATIONS AND DEFINITIONS . . . . . . . . . . . . . . . 48

ANNEX

C.

INDEX OF NATO STOCK NUMBERS . . . . . . . . . . . . . . . . 49

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

1.

PERFORMANCE SPECIFICATION
This standard contains no Performance Specification information.

2.

NATIONAL/INTERNATIONAL REGULATIONS
This standard contains no National/International Regulations information.

3.

MILITARY STANDARDS/REQUIREMENTS
This standard contains no Military Standards/Requirements information.

4.

DESIGN REQUIREMENTS/GUIDANCE

4.1

Imperial Spigot Type (Castellated) Hull Glands


a.

Hull glands in this section are designed to be fitted to Swiftsure and Trafalgar
classes of Submarine only. They may be installed singularly in a single pressure
hull insert or grouped within a five way pressure hull insert.

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

Cables HP Side
NSN 6145995227877
Type Screened Quad
Conductor CSA 0.5 mm2
Volts
600
Amps
2
No. of Cables
1

9.75

Gland and Cable Assembly


NSN 5975995224397
ADREF No. J868440509
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

3.125

3.916
UNS 1A Thread

0.875

3.798

`O' Seal
5330999237760

Cables LP Side
NSN 6145995227877
Type Screened Quad
Conductor CSA 0.5 mm2
Volts
600
Amps
2
No. of Cables
1

2.377

Figure Reproduced From Drawing No. DEE 96872

FIGURE 4.1 Gland and Cable Assembly Spigot Type, 1 Screened Quad, (Type F)
9

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

9.75

Cables HP Side
NSN 6145997248833
Type Single Core
Conductor CSA 6 mm2
Volts
600
Amps
19.5
No. of Cables
4

Gland and Cable Assembly


NSN 5975995224398
ADREF No. J868440514
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

3.125

3.916
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN 6145995252037
Type Single Core
Conductor CSA 6 mm2
Volts
600
Amps
19.5
No. of Cables
4

`O' Seal
5330999237760
2.377

Figure Reproduced From Drawing No. DEE 96873

FIGURE 4.2 Gland and Cable Assembly Spigot Type, 4 Way, (Type G)
10

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

9.75

Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
6

Gland and Cable Assembly


NSN 5975995224393
ADREF No. J868440505
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

3.125

3.916
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN 6145997248840
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
6

`O' Seal
5330999237760
2.377

Figure Reproduced From Drawing No. DEE 96869

FIGURE 4.3 Gland and Cable Assembly Spigot Type, 6 Screened Pairs, (Type B)
11

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

9.75

Cables HP Side
NSN 6145997248831
Type Twisted Pair
Conductor CSA 1.5 mm2
Volts
600
Amps
4
No. of Cables
8

Gland and Cable Assembly


NSN 5975995224392
ADREF No. J868440500
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

3.125

3.916
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN 6145997248840
Type Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
8

`O' Seal
5330999237760
2.377

Figure Reproduced From Drawing No. DEE 96868

FIGURE 4.4 Gland and Cable Assembly Spigot Type, 8 Pair, (Type A)
12

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

9.75

Cables HP Side
NSN 6145995278993
Type Coaxial 75 Ohms
Conductor CSA Volts
Amps
No. of Cables
4

Gland and Cable Assembly


NSN 5975995224394
ADREF No. J868440506
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

3.125

3.916
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN 6145995278993
Type Coaxial 75 Ohms
Conductor CSA Volts
Amps
No. of Cables
4

`O' Seal
5330999237760
2.377

Figure Reproduced From Drawing No. DEE 96870

FIGURE 4.5 Gland and Cable Assembly Spigot Type, 4 Coaxial 75 Ohms, (Type C)

13

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

Cables HP Side
NSN 6145995278994
Type Coaxial 50 Ohms
Conductor CSA Volts
Amps
No. of Cables
4

9.75

Gland and Cable Assembly


NSN 5975995224395
ADREF No. J868440507
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

3.125

3.916
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN 6145995278994
Type Coaxial 50 Ohms
Conductor CSA Volts
Amps
No. of Cables
4

`O' Seal
5330999237760
2.377

Figure Reproduced From Drawing No. DEE 96870

FIGURE 4.6 Gland and Cable Assembly Spigot Type, 4 Coaxial 50 Ohms, (Type C)
NOTE Not to be used for new installations

14

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale
Cables HP Side
NSN 6145997248822
Type 50 Ohm Coaxial
Conductor CSA Volts
Amps
No. of Cables
4

9.75

Gland and Cable Assembly


NSN ADREF No. Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

3.125

3.916
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN 6145997248834
Type 50 Ohm Coaxial
Conductor CSA Volts
Amps
No. of Cables
4

`O' Seal
5330999237760
2.377

FIGURE 4.7 Gland and Cable Assembly, Spigot Type, 4 Coaxial 50 Ohms

15

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale
Cables HP Side
NSN 6145995255127
Type 3 Core
Conductor CSA 4.5 mm2
Volts
440
Amps
26
No. of Cables
1

Cables LP Side
NSN 6145995255127
Type 3 Core
Conductor CSA 4.5 mm2
Volts
440
Amps
26
No. of Cables
1
NSN 6145997248840
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
1

3.125

3.916
UNS 1A Thread
3.798
0.875

Gland and Cable Assembly


NSN 5975995224399
ADREF No. J868440510
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

9.75

NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
1

`O' Seal
5330999237760
2.377

Figure Reproduced From Drawing No. DEE 96874

FIGURE 4.8 Gland and Cable Assembly, Spigot Type, 1 Screened Pair + 1 x 3 Core (Type
H)
16

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale
Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

9.75

Gland and Cable Assembly


NSN
ADREF No.
Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

3.125

3.916
UNS 1A Thread
3.798
0.875

Cables LP Side
NSN 6145997248842
Type 19 Optomised
Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
1

`O' Seal
5330999237760
2.377

FIGURE 4.9 Gland and Cable Assembly, Spigot Type, 19 Screened Pair

17

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale
Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

9.75

Gland and Cable Assembly


NSN
ADREF No.
Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

3.125

3.916
UNS 1A Thread
3.798
0.875

Cables LP Side
NSN 6145997248836
Type 19 Super Screened
Twisted Pair
Conductor CSA 0.4 mm2
Volts
600
Amps
1.5
No. of Cables
1

`O' Seal
5330999237760
2.377

FIGURE 4.10 Gland and Cable Assembly, Spigot Type, 19 Screened Pair

18

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

246

Cables HP Side
NSN 6145997248824
Type 3 Core Screened
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

Gland and Cable Assembly


NSN 2040992192669
ADREF No.
Cable Length Inboard (LP ) 7 m
Cable Length Outboard (HP) 7 m

79

8 TPI UNS
96.3

Cables LP Side
NSN 6145997248837
Type 3 Core Screened
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

`O' Seal
329
60.32

Figure Reproduced From Drawing No. SDN 007 528 050

FIGURE 4.11 Gland and Cable Assembly, Spigot Type, 19 x 3 Core Screened
19

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

246

Gland and Cable Assembly


NSN ADREF No. Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

79

8 TPI UNS

22

96.3

Cables LP Side
NSN 6145997248840
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

`O' Seal
329
60.32

Figure Reproduced From Drawing No. SDN 007 528 048

FIGURE 4.12 Gland and Cable Assembly, Spigot Type, 19 Screened Pair
20

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

4.2

Multi-Stem Glands
a.

Hull glands in this section are multi - stem type.

21

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

14.125

Dimensions in Inches
Not to Scale

18.375

1.0

8.0
8 Holes 0.812 Dia
Equispaced on
6.5 PCD

7.125

2.996

Gland and Cable Assembly


NSN 5975995226244
ADREF No. J868440502
Cable Length Inboard (LP ) 40 Ft Nom
Cable Length Outboard (HP) 20 Ft Nom

Cables LP Side
NSN 6145995227892
Type 30 Quads (Each Quad
Individually Screened)
Conductor CSA 0.5 mm2
Volts
250
Amps
1.73
No. of Cables
1

Cables HP Side
NSN 6145995227875
Type Twisted Pair
Conductor CSA 1.3 mm2
Volts
600
Amps
4
No. of Cables
30

Figure Reproduced From Drawing No. DEE 87112

FIGURE 4.13 Gland and Cable Assembly Multi-Stem Type, 30 Pair

22

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

11.3125

4.875

17.75

1.0

8.0

7.125

8 Holes 0.812 Dia


on 6.5 PCD

2.996

Gland and Cable Assembly


NSN 5975994561492
ADREF No. J868440498
Cable Length Inboard (LP ) 60 Ft Nom
Cable Length Outboard (HP) 100 Ft Nom

Cables LP Side
NSN 6145995227892
Type 30 Quads (Each Quad
Individually Screened)
Conductor CSA 0.5 mm2
Volts
250
Amps
1.73
No. of Cables
1

Cables HP Side
NSN 6145995227875
Type Twisted Pair
Conductor CSA 1.3 mm2
Volts
600
Amps
4
No. of Cables
60

Figure Reproduced From Drawing No. DEE 87124

FIGURE 4.14 Gland and Cable Assembly Multi-Stem Type, 60 Pair


23

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

15.625

4.875

17.75

1.375

15

5.69

`O' Seal
5330999237764

12 Holes 1.3125 Dia


on 12 Inch PCD

2.996

Gland and Cable Assembly


NSN 5975995253848
ADREF No. J868440513
Cable Length Inboard (LP ) 35 Ft
Cable Length Outboard (HP) 35 Ft

Cables LP Side
NSN 6145995227892
Type 30 Quads (Each Quad
Individually Screened)
Conductor CSA 0.5 mm2
Volts
600
Amps
1.73
No. of Cables
1

Cables HP Side
NSN 6145995227875
Type Twisted Pair
Conductor CSA 1.3 mm2
Volts
600
Amps
4
No. of Cables
60

Figure Reproduced From Drawing No. SDN 007 502 353

FIGURE 4.15 Gland and Cable Assembly Multi-Stem Type, 60 Pair


24

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

4.3

Special Hull Glands


a.

The glands illustrated in this section are special service glands and are not to be
adopted for any new service except when approved by SSA/MLS2.

25

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

3.125

3.0

9.75

4.75

1.5

1.0

1.0

3.916
UNS 1A Thread
3.798
0.656 0.875

Cables HP and LP Sides


NSN Not Applicable
Type Special Coaxial
(As UR 67)
No. of Cables 1

`O' Seal
5330999237760
2.377

Service Aerial Outfits


AJE and AWG

Gland and Cable Assembly


NSN 5975995224400
ADREF No. J868440511
Cable Length Inboard (LP ) 12 Ft
Cable Length Outboard (HP) 12 Ft

Figure Reproduced From Drawing No. DEE 96875

FIGURE 4.16 Gland and Cable Assembly Spigot Type J


26

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

9.75

Cables HP Side
NSN
Type Single Core XLP Sheath
Conductor CSA 0.4 Inches2
Volts
440
Amps
400
No. of Cables
1

3.125

3.916

0.875

UNS 1A Thread

`O' Seal
5330999237760
2.377
7.0

Conductor Pin

Service Secondary Propulsion Motor


Figure Reproduced From Drawing No. STC RC 6592

FIGURE 4.17 Gland and Cable Assembly Spigot Type (SPM)


27

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

Cables HP Side
NSN Type 19 Quad
Conductor CSA
Volts
Amps
No. of Cables

0.3 mm2
115
0.3
1

9.75

Gland and Cable Assembly


NSN ADREF No. Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

3.125

3.916
UNS 1A Thread

Cables LP Side
NSN Type 19 Quad
Conductor CSA
Volts
Amps
No. of Cables

0.875

3.798

`O' Seal
5330999237760

0.3 mm2
115
0.3
1

2.377

Service Towed Array


Figure Reproduced From Drawing No. AUWE 1001931100

FIGURE 4.18 Gland and Cable Assembly Spigot Type, 19 Quad


28

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

Cables HP Side
NSN Type 45 Quad (To Spec AH M271)
Conductor CSA 0.3 mm2
Volts
115
Amps
0.3
No. of Cables
1

11

Gland and Cable Assembly


NSN ADREF No. Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

3.125

3.196
UNS 1A Thread

0.875

3.798

Cables LP Side
NSN Type 45 Quad (Spec AHM271)
Conductor CSA 0.3 mm2
Volts
115
Amps
0.3
No. of Cables
1

`O' Seal
5330999237760
2.377

Service Towed Array


Figure Reproduced From Drawing No. AMEECO AH 3104

FIGURE 4.19 Gland and Cable Assembly Spigot Type, 45 Quad


29

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

Cables HP Side
NSN 6145995271312
Type 6 Core
Conductor CSA 0.5 mm2
Volts
600
Amps
3
No. of Cables
4

9.75

Gland and Cable Assembly


NSN ADREF No. Cable Length Inboard (LP ) 55 Ft
Cable Length Outboard (HP) 20 Ft
3.125

3.196
UNS 1A Thread
3.798
0.875

Cables LP Side
NSN 6145991116772
Type 6 Core PVC Sheath
DEF STAN 6112 Pt 5
Conductor CSA 0.5 mm2
Volts
440
Amps
3
No. of Cables
4

`O' Seal
5330999237760
2.377

Service Sonar 2007CD


Figure Reproduced From Drawing No. SDN 007 509 367

FIGURE 4.20 Gland and Cable Assembly Spigot Type, 4 x 6 Core


30

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

160

Cables HP Side
NSN 6145995216965
Type 14 Core Heavy Duty
CSP Sheath
Conductor CSA 35 mm2
Volts
440
Amps
70
No. of Cables
1

204 Dia Ten Holes


17.5 Dia on 175 PCD
440

`O' Seal

Gland and Cable Assembly


NSN ADREF No. Cable Length Inboard (LP ) As Req
Cable Length Outboard (HP) As Req

116

Cables LP Side
NSN 6145995216866
Type 14 Core Heavy Duty
CSP Sheath
Conductor CSA 35 mm2
Volts
440
Amps
83
No. of Cables
1
Service Degaussing `M' Coils
Figure Reproduced From Drawing No. SDN 007 038 075

FIGURE 4.21 Gland and Cable Assembly Flange Type, 14 Core


31

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in Inches
Not to Scale

20.5

13.25

Gland and Cable Assembly


NSN 5975999249194
ADREF No. J868440504

Flange 9.5 Dia 12 Holes


25/ Dia on 8.0 PCD
32

Service AWJ Aerial Feeder

Figure Reproduced From Drawing No. ASWE 278477

FIGURE 4.22 Gland Flange Type, AWJ


32

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

20

12

Dimensions in Inches
Not to Scale

Gland Assembly
NSN 5975999247518
ADREF No. -

Flange 10 Dia
Welded to Hull

Service AWJ Aerial Feeder

Figure Reproduced From Drawing No. ASWE C299809

FIGURE 4.23 Gland, AWJ


33

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

4.4

Metric Spigot Type Pressure Hull Glands


a.

Hull glands in this section are designed to be fitted to the Vanguard class of
Submarine only. They may be installed singularly in a single pressure hull
insert or grouped within a multipressure hull insert.

34

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145997248822
Type 50 Ohm Coaxial
Conductor CSA Length
6m
Volts
Amps
No. of Cables
4

Gland and Cable Assembly


NSN 5975997948800
ADREF No. Cable Length Inboard (LP ) 12 m
Cable Length Outboard (HP) 5 m

211

NSN 6510991688553
ADREF No. Cable Length Inboard (LP ) 3 m
Cable Length Outboard (HP) 15 m
NSN 6510991924968
ADREF No. Cable Length Inboard (LP ) 3 m
Cable Length Outboard (HP) 3 m

79

NSN 6510995912734
ADREF No. Cable Length Inboard (LP ) 15 m
Cable Length Outboard (HP) 18 m

M100x3

22

96.30

Cables LP Side
NSN 6145997248834
Type 50 Ohm Coaxial
Conductor CSA Length
6m
Volts
Amps
No. of Cables
4

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 044 060

FIGURE 4.24 Gland and Cable Assembly, Spigot Type Metric, 4 Coaxial 50 Ohms (Type 11)

35

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Length
6m
Volts
600
Amps
2
No. of Cables
19

211

Gland and Cable Assembly


NSN 5975990524083
ADREF No. Cable Length Inboard (LP ) 30 m
Cable Length Outboard (HP) 5 m

79

NSN 2040990563620
ADREF No. Cable Length Inboard (LP ) 20 m
Cable Length Outboard (HP) 5 m

M100x3

22

96.30

Cables LP Side
NSN 6145997248842
Type 19 Optimized Screened
Conductor CSA 0.6 mm2
Length
6m
Volts
600
Amps
2
No. of Cables
1

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 045

FIGURE 4.25 Gland and Cable Assembly, Spigot Type Metric, 19 Screened Pair (Type 1)

36

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale
Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Length
6m
Volts
600
Amps
2
No. of Cables
19

211

Gland and Cable Assembly


NSN 5975997654444
ADREF No. Cable Length Inboard (LP ) 22 m
Cable Length Outboard (HP) 48 m
79

M100x3

96.30
22

Cables LP Side
NSN 6145997248836
Type 19 Super Screened
Twisted Pairs
Conductor CSA 0.4 mm2
Length
6m
Volts
600
Amps
1.5
No. of Cables
1

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 046

FIGURE 4.26 Gland and Cable Assembly, Spigot Type Metric, 19 Screened Pair (Type 2)
37

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145995434475
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

211

Gland and Cable Assembly


NSN 5975996606050
ADREF No. Cable Length Inboard (LP ) 20 m
Cable Length Outboard (HP) 5 m

79

M100x3

96.30
22

Cables LP Side
NSN 6145997248840
Type Screened Twisted Pair
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 047

FIGURE 4.27 Gland and Cable Assembly, Spigot Type Metric, 19 Screened Pair (Type 3)

38

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145997248824
Type 3 Core Screened
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

211

Gland and Cable Assembly


NSN 5975991799257
ADREF No. Cable Length Inboard (LP ) 5 m
Cable Length Outboard (HP) 5 m

79

M100x3

96.30
22

Cables LP Side
NSN 6145997248837
Type 3 Core Screened
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
19

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 049

FIGURE 4.28 Gland and Cable Assembly, Spigot Type Metric, 19 Screened Triple (Type 5)
39

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

211

Cables HP Side
NSN 6145997248829
Type 3 Screened Pairs
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
3

79

M100x3
96.30
22

Cables LP Side
NSN 6145997248841
Type 9 Screened Pairs
Conductor CSA 0.6 mm2
Volts
600
Amps
2
No. of Cables
1

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 051

FIGURE 4.29 Gland and Cable Assembly, Spigot Type Metric, 3 X 3 Screened Pair (Type 7)

40

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145995255127
Type 3 Core
Conductor CSA 4.5 mm2
Volts
440
Amps
26
No. of Cables
1

211

Gland and Cable Assembly


NSN 5975998499861
ADREF No. Cable Length Inboard (LP ) 10 m
Cable Length Outboard (HP) 5 m

79

M100x3
96.30
22

Cables LP Side
NSN 6145995255127
Type 3 Core
Conductor CSA 4.5 mm2
Volts
440
Amps
26
No. of Cables
1

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 052

FIGURE 4.30 Gland and Cable Assembly, Spigot Type Metric, 1 Triple (Type 8)
41

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145997248831
Type Twisted Pair
Conductor CSA 1.5 mm2
Volts
600
Amps
4
No. of Cables
19

211

Gland and Cable Assembly


NSN 6150991259056
ADREF No. Cable Length Inboard (LP ) 4 m
Cable Length Outboard (HP) 3 m

79

M100x3
96.30
22

Cables LP Side
NSN 6145997248843
Type Twisted Pair
Conductor CSA 1.5 mm2
Volts
600
Amps
4
No. of Cables
19

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 433

FIGURE 4.31 Gland and Cable Assembly, Spigot Type Metric, 19 Pair
42

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

274

Cables HP Side
NSN Type 52 Quad Tinned Copper
Wire Screen
Conductor CSA 0.25 mm2
Length
200 m
Volts
500
Amps
0.75
No. of Cables
1

79

M100x3
96.30
22

Cables LP Side
NSN Type 208 Conductor Shielded
Jacketed Cable
Conductor CSA 0.15 mm2
Length
5m
Volts
600
Amps
0.5
No. of Cables
1

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 528 756

FIGURE 4.32 Gland and Cable Assembly, Spigot Type Metric, 1 X 52 Quad
43

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

Dimensions in mm
Not to Scale

Cables HP Side
NSN 6145997248833
Type Single Core
Conductor CSA 6 mm2
Volts
600
Amps
25
No. of Cables
4

211

Gland and Cable Assembly


NSN 2040998677897
ADREF No. Cable Length Inboard (LP ) 5 m
Cable Length Outboard (HP) 5 m

79

M100x3
96.30

22

Cables LP Side
NSN 6145997248845
Type Single Core
Conductor CSA 6 mm2
Volts
600
Amps
25
No. of Cables
4

`O' Seal
052357
62.95

Figure Reproduced From Drawing No. SDN 007 531 320

FIGURE 4.33 Gland and Cable Assembly, Spigot Type Metric, 4 Single Core
44

INT Def Stan 02524 Part 1 / Issue 2


(NES 524)

5.

CORPORATE EXPERIENCE & KNOWLEDGE


This standard contains no Corporate Experience & Knowledge information.

45

INT Def Stan 02524 Part 1 / Issue 2


(NES 524

ANNEX A.
RELATED DOCUMENTS
A.1

The following documents and publications are referred to in this standard:

Drawing AMEECO Hydrospace


AH3104

Gland for 45 Quad Cable for Towed Array

Drawing ASWE 278477

Gland Aerial Feeder NSN 5975-99-924-9194

Drawing ASWE C299809

Gland Aerial Feeder NSN 5985-99-924-7518

Drawing AUWE 100193-1100

Gland 19 Quad Cable for Towed Array

Drawing DEE 87112

Cable and Gland Assembly Submarine Hull, Pressure,


30 Pair, NSN 5975-99-522-6244

Drawing DEE 87124

Cable and Gland Assembly, Submarine Hull,


Pressure, 60 Pair, NSN 5975-99-456-1492

Drawing DEE 96868

Gland 8 Way (Type A) Assembly


NSN 5975-99-522-4392

Drawing DEE 96869

Gland 6 Way (Type B) Assembly


NSN 5975-99-522-4393

Drawing DEE 96870

Gland 4 Way (Type C) Assembly


NSN 5975-99-522-4394,
NSN 5975-99-522-4395

Drawing DEE 96872

Gland Single Way (Type F) Assembly


NSN 5975-99-522-4397

Drawing DEE 96873

Gland 4 Way (Type G) Assembly


NSN 5975-99-522-4398

Drawing DEE 96874

Gland 2 Way (Type H) Assembly


NSN 5975-99-522-4399

Drawing DEE 96875

Harness for Aerial Assembly (Type J) Castellated Nut


Assembly NSN 5975-99-522-4400

Drawing
SDN 007 038 075

Pressure Hull Gland for Degaussing `M' Coils

Drawing
SDN 007 044 060

Gland and Cable Assembly, Spigot Type Metric, 4


Coax 50 ohms (Type 11)

Drawing
SDN 007 502 353

Cable and Gland Assembly. Electrical. Submarine


Hull Pressure, 60 Pairs, Flanged Improved Type
NSN 5975-99-525-3848

Drawing
SDN 007 509 367

Gland 4 Way 6 Core

Drawing
SDN 007 528 045

Gland and Cable Assembly Spigot Type Metric, 19


Screened Pair (Type 1)

Drawing
SDN 007 528 046

Gland and Cable Assembly Spigot Type Metric, 19


Screened Pair (Type 2)

Drawing
SDN 007 528 047

Gland and Cable Assembly Spigot Type Metric, 19


Screened Pair (Type 3)

Drawing
SDN 007 528 048

Gland and Cable Assembly Spigot Type 19 Way

Drawing
SDN 007 528 049

Gland and Cable Assembly Spigot Type Metric, 19


Screened Triple, (Type 5)

46

INT Def Stan 02 524 Part 1 / Issue 2


(NES 524)

Drawing
SDN 007 528 050

Gland and Cable Assembly Spigot Type 19 Way

Drawing
SDN 007 528 051

Gland and Cable Assembly Spigot Type Metric, 3 


Screened Pair, (Type 7)

Drawing
SDN 007 528 052

Gland and Cable Assembly Spigot Type Metric, 1


Triple, (Type 8)

Drawing
SDN 007 528 433

Gland and Cable Assembly, Spigot Type Metric, 19


Pair

Drawing
SDN 007 528 756

Gland and Cable Assembly, Spigot Type Metric, 1 


52 Quad

Drawing
SDN 007 531 320

Gland and Cable Assembly, Spigot Type Metric, 4


Way,

Drawing STC RC6592

Gland Assembly for Secondary Propulsion Motor

47

INT Def Stan 02524 Part 1 / Issue 2


(NES 524

ANNEX B.
ABBREVIATIONS AND DEFINITIONS
B.1

B.2

For the purpose of this standard the following abbreviations apply:


ADREF No

Admiralty Reference Number

CSA

CrossSectional Area

CSP

Chlorosulphonated Polyethylene

DPA

Defence Procurement Agency

DLO

Defence Logistics Organisation

HP

High Pressure

LP

Low Pressure

MLS

Marine Electrical Systems

MOD

Ministry of Defence

NES

Naval Engineering Standard

NSN

NATO Stock Number

PCD

Pitch Circle Diameter

PCP

Polychloroprene

PVC

Polyvinyl Chloride

SDN

Service Drawing Number

SSA

Ship Support Agency

SSK

Ship Submersible Kinetic

SSN

Ship Submersible Nuclear

SSBN

Ship Submersible Ballistic Nuclear

There are no Definitions for this standard.

48

INT Def Stan 02 524 Part 1 / Issue 2


(NES 524)

ANNEX C.
INDEX OF NATO STOCK NUMBERS
NATO STOCK No

PAGE No

2040992192669

4.13

2040990563620

4.30

2040998677897

4.38

5330999237760

Various

5330999237764

4.18

5975990524083

4.30

5975991799257

4.33

5975994561492

4.17

5975995224392

4.6

5975995224393

4.5

5975995224394

4.7

5975995224395

4.8

5975995224397

4.3

5975995224398

4.4

5975995224399

4.10

5975995224400

4.20

5975995226244

4.16

5975996606050

4.32

5975997654444

4.31

5975997948800

4.29

5975998499861

4.35

5975995253848

4.18

5975999249194

4.26

5985999247518

4.27

6145991116772

4.24

6145995216866

4.25

6145995216965

4.25

6145995227875

4.16 / 4.17 / 4.18

6145995227877

4.3

6145995252037

4.4

6145995255127

4.10 / 4.35

6145995271312

4.24

6145995278993

4.7

6145995278994

4.8

6145995434475

4.5 / 4.10 / 4.11 / 4.12 / 4.14 / 4.30 / 4.31 / 4.32

49

INT Def Stan 02524 Part 1 / Issue 2


(NES 524

NA

TO

STOCK

No

P AGE

No

6145997248822

4.9 / 4.29

6145997248824

4.13 / 4.33

6145997248829

4.34

6145997248831

4.6 / 4.36

6145997248833

4.4 / 4.38

6145997248834

4.9 / 4.29

6145997248836

4.12 / 4.31

6145997248837

4.13 / 4.33

6145997248840

4.5 / 4.6 / 4.10 / 4.14 / 4.32

6145997248841

4.34

6145997248842

4.11 / 4.30

6145997248843

4.36

6145997248845

4.38

6150991259056

4.36

6510991688553

4.29

6510991924968

4.29

6510995912734

4.29

50

Inside Rear Cover

Crown Copyright 2002


Copying Only as Agreed with DStan

Defence Standards are Published by and Obtainable from:


Defence Procurement Agency
An Executive Agency of The Ministry of Defence
UK Defence Standardization
Kentigern House
65 Brown Street
GLASGOW G2 8EX

DStan Helpdesk
Tel 0141 224 2531/2
Fax 0141 224 2503
Internet e-mail enquiries@dstan.mod.uk

File Reference
The DStan file reference relating to work on this standard is D/DStan/69/02/524 Pt 1.
Contract Requirements
When Defence Standards are incorporated into contracts users are responsible for their correct
application and for complying with contractual and statutory requirements. Compliance with
a Defence Standard does not in itself confer immunity from legal obligations.
Revision of Defence Standards
Defence Standards are revised as necessary by up issue or amendment. It is important that
users of Defence Standards should ascertain that they are in possession of the latest issue or
amendment. Information on all Defence Standards is contained in Def Stan 00-00 Standards
for Defence Part 3 , Index of Standards for Defence Procurement Section 4 Index of Defence
Standards and Defence Specifications published annually and supplemented regularly by
Standards in Defence News (SID News). Any person who, when making use of a Defence
Standard encounters an inaccuracy or ambiguity is requested to notify the Directorate of
Standardization (DStan) without delay in order that the matter may be investigated and
appropriate action taken.

Vous aimerez peut-être aussi