Académique Documents
Professionnel Documents
Culture Documents
Series/Type:
Date:
January 2014
EPCOS AG 2014. Reproduction, publication and dissemination of this publication, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Y2 / 300 V AC
Typical applications
Y2 class for interference suppression
"Line to ground" applications.
Dimensional drawing
Climatic
Max. operating temperature: 110 C
Climatic category (IEC 60068-1):
40/110/56
Construction
Dielectric: polypropylene (MKP)
Plastic case (UL 94 V-0)
Epoxy resin sealing (UL 94 V-0)
Dimensions in mm
Features
Very small dimensions
Good self-healing properties
High voltage capability
RoHS-compatible
Halogen-free capacitors available on
request
Terminals
Parallel wire leads, lead-free tinned
Special lead lengths available on request
Marking
Manufacturer's logo, lot number,
date code, rated capacitance (coded),
capacitance tolerance (code letter),
rated AC voltage (IEC),
series number, sub-class (Y2),
dielectric code (MKP), climatic category,
passive flammability category, approvals.
Type
10
0.6
B32021
15 ... 27.5
0.8
37.5
1.0
B32026
Marking example
(position of marks may vary):
Delivery mode
Bulk (untaped)
Taped (Ammo pack or reel)
For taping details, refer to chapter
"Taping and packing"
Page 2 of 21
Approvals
Approval marks
Standards
EN 60384-14, IEC 60384-14
Certificate
40018909
UL1414, UL1283
CSA C22.2 No. 1 / No. 8
E97863 / E157153
E97863 / E157153
(approved by UL)
E97863 (approved by UL)
Notes:
Page 3 of 21
15 mm
22.5 mm
27.5 mm
37.5 mm
Type
B32022
B32023
B32024
B32026
B32021
CR (F)
0.0010
0.0015
0.0022
0.0033
0.0047
0.0056
0.0068
0.0082
0.010
0.015
0.022
0.033
0.047
0.056
0.068
0.082
0.10
0.15
0.22
0.33
0.39
0.47
0.56
0.68
0.82
1.0
Page 4 of 21
Max. dimensions
whl
mm
mm
10
15
Ordering code
(composition see
below)
B32021A3102+***
B32021A3152+***
B32021A3222+***
B32021A3332+***
B32021A3472+***
B32021A3562+***
B32021A3682+***
B32021A3822+***
B32021A3103M***
B32022A3103+***
B32022A3153+***
B32022A3223M***
B32022B3223+***
B32022A3333+***
B32022A3473M***
B32022B3473+***
B32022A3563+***
B32022A3683M***
B32022A3823M***
Straight
terminals,
Ammo
pack
pcs./MOQ
4000
4000
4000
4000
3320
3320
3320
2720
2720
4680
3840
3840
3320
2920
2720
2560
2560
2560
Straight
Straight
terminals, terminals,
Reel
Untaped
pcs./MOQ
6800
6800
6800
6800
5200
5200
5200
4400
4400
5200
4400
4400
3600
3000
2800
2800
2800
2800
2200
pcs./MOQ
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
4000
2000
2000
2000
2000
2000
1200
Page 5 of 21
Max. dimensions
whl
mm
22.5
0.047
0.056
0.068
0.068
0.082
0.10
0.10
0.15
0.15
0.22
0.22
0.33
0.39
0.15
0.22
0.22
0.33
0.33
0.47
0.47
27.5
Ordering code
(composition see
below)
B32023A3473+***
B32023A3563M***
B32023A3683+***
B32023B3683M***
B32023A3823+***
B32023A3104M***
B32023B3104+***
B32023A3154M***
B32023B3154+***
B32023A3224M***
B32023B3224+***
B32023A3334+***
B32023A3394M***
B32024A3154+***
B32024A3224M***
B32024B3224+***
B32024A3334M***
B32024B3334+***
B32024A3474M***
B32024C3474+***
Straight
terminals,
Ammo
pack
pcs./MOQ
2720
2720
2320
2200
1920
1920
1560
1560
Straight
Straight
terminals, terminals,
Reel
Untaped
pcs./MOQ
2800
2800
2400
2000
2000
2000
1600
1600
1400
1400
1400
1000
pcs./MOQ
2880
2880
2520
2280
2040
2040
2160
2160
2160
1800
2160
2160
2160
1280
1280
1280
1040
1040
960
880
Page 6 of 21
Max. dimensions
whl
mm
27.5
0.47
0.56
0.68
0.68
0.68
0.82
1.0
0.33
0.47
0.56
0.56
0.68
0.82
0.82
1.0
1.0
37.5
Ordering code
(composition see
below)
B32024B3474+***
B32024A3564+***
B32024B3684+***
B32024A3684M***
B32024C3684+***
B32024A3824+***
B32024A3105M***
B32026A3334+***
B32026A3474+***
B32026A3564M***
B32026B3564+***
B32026A3684+***
B32026A3824M***
B32026B3824+***
B32026A3105M***
B32026B3105+***
Straight
terminals,
Ammo
pack
pcs./MOQ
Straight
Straight
terminals, terminals,
Reel
Untaped
pcs./MOQ
pcs./MOQ
800
880
800
720
720
640
640
1620
1380
1380
800
800
800
720
720
640
Page 7 of 21
Technical data
Reference standard: IEC / UL 60384-14. All data given at T = 20 C unless otherwise specified.
Rated AC voltage ( IEC 60384-14 )
1500 V
+110 C
DC test voltage
at
CR 0.33 F
1 kHz
CR > 0.33 F
CR 0.33 F
CR > 0.33 F
100 000 M
30 000 s
Capacitance tolerances
(measured at 1 kHz)
10 mm
800
677 000
15 mm
600
508 000
22.5 mm
500
423 000
Page 8 of 21
27.5 mm
400
338 000
37.5 mm
300
254 000
Reference
Electrical
Parameters
IEC 60384-14
Robustness of
terminations
Resistance to
soldering heat
Conditions of test
Voltage Proof:
Between terminals,
1500 V AC, 1 min.
Terminals and enclosure: 2 VR +
1500 V AC
Insulation resistance, RINS
Capacitance, C
Dissipation factor, tan
IEC 60068-2-21 Tensile strength (test Ua1)
Tensile
Wire diameter
force
0.5 < d1 0.8 mm
10 N
0.8 < d1 1.25 mm 20 N
IEC 60068-2-20, Solder bath temperature at
test Tb,
260 5 C, immersion for
method 1A
10 seconds
Performance
requirements
Within specified limits
C/C0 5%
tan within specified
limits
No visible damage
IC/C0 I 5%
tan within specified
limits
Vibration
IEC 60384-14
Bump
IEC 60384-14
Climatic
sequence
IEC 60384-14
Page 9 of 21
Damp Heat
Steady State
IEC 60384-14
Test Ca
40 C / 93% RH / 56 days
Impulse test
Endurance
IEC 60384-14
3 impulses
TB / 1.7 VR / 1000 hours,
1000 Vrms for 0.1 s every hour
Passive
flammability
IEC 60384-14
Active
flammability
IEC 60384-14
20 discharges at 2.5 kV + VR
Page 10 of 21
No visible damage
IC/C0 I 5%
I tan I 0.008,
C 1 F
I tan I > 0.005,
C > 1 F
Voltage proof
RINS 50% of initial limit
No visible damage
IC/C0 I 10%
I tan I 0.008,
C 1 F
I tan I > 0.005,
C > 1 F
Voltage proof
RINS 50% of initial limit
Mounting guidelines
1
Soldering
1.1
Solderability of leads
The solderability of terminal leads is tested to IEC 60068-2-20, test Ta, method 1.
Before a solderability test is carried out, terminals are subjected to accelerated ageing (to
IEC 60068-2-2, test Ba: 4 h exposure to dry heat at 155 C). Since the ageing temperature is far
higher than the upper category temperature of the capacitors, the terminal wires should be cut off
from the capacitor before the ageing procedure to prevent the solderability being impaired by the
products of any capacitor decomposition that might occur.
Solder bath temperature
235 5 C
Soldering time
2.0 0.5 s
Immersion depth
Evaluation criteria:
Visual inspection
1.2
Resistance to soldering heat is tested to IEC 60068-2-20, test Tb, method 1A.
Conditions:
Series
Page 11 of 21
10 1 s
5 1 s
<4s
recommended soldering
profile for MKT uncoated
(lead spacing 10 mm) and
insulated (B32559)
Immersion depth
Shield
Evaluation criteria:
Visual inspection
C/C0
tan
No visible damage
2% for MKT/MKP/MFP
5% for EMI suppression capacitors
As specified in sectional specification
Page 12 of 21
1.3
Permissible heat exposure loads on film capacitors are primarily characterized by the upper category temperature Tmax. Long exposure to temperatures above this type-related temperature limit
can lead to changes in the plastic dielectric and thus change irreversibly a capacitor's electrical
characteristics. For short exposures (as in practical soldering processes) the heat load (and thus
the possible effects on a capacitor) will also depend on other factors like:
Pre-heating temperature and time
Forced cooling immediately after soldering
Terminal characteristics:
diameter, length, thermal resistance, special configurations (e.g. crimping)
Height of capacitor above solder bath
Shadowing by neighboring components
Additional heating due to heat dissipation by neighboring components
Use of solder-resist coatings
The overheating associated with some of these factors can usually be reduced by suitable countermeasures. For example, if a pre-heating step cannot be avoided, an additional or reinforced
cooling process may possibly have to be included.
EPCOS recommends the following conditions:
Pre-heating with a maximum temperature of 110 C
Temperature inside the capacitor should not exceed the following limits:
MKP/MFP 110 C
MKT 160 C
When SMD components are used together with leaded ones, the leaded film capacitors should
not pass into the SMD adhesive curing oven. The leaded components should be assembled after the SMD curing step.
Leaded film capacitors are not suitable for reflow soldering.
Uncoated capacitors
For uncoated MKT capacitors with lead spacings 10 mm (B32560/B32561) the following measures are recommended:
pre-heating to not more than 110 C in the preheater phase
rapid cooling after soldering
Application note for X1 / X2 EMI capacitors
Page 13 of 21
Typical Applications:
Power meters
ECUs for white goods and household
appliances
Different sensor applications
Severe ambient conditions
Basic circuit
Basic circuit
Required features
Required features
Page 14 of 21
Storage conditions
Flammability
Resistance to
vibration
Safety information
Reference chapter
"General technical
information"
Make sure that capacitors are stored within the
4.5
specified range of time, temperature and humidity "Storage conditions"
conditions.
Avoid external energy, such as fire or electricity
5.3
(passive flammability), avoid overload of the
"Flammability"
capacitors (active flammability) and consider the
flammability of materials.
Do not exceed the tested ability to withstand
5.2
vibration. The capacitors are tested to
"Resistance to vibration"
IEC 60068-2-6.
EPCOS offers film capacitors specially designed
for operation under more severe vibration regimes
such as those found in automotive applications.
Consult our catalog "Film Capacitors for
Automotive Electronics".
Page 15 of 21
Topic
Safety information
Soldering
Reference chapter
"Mounting guidelines"
1 "Soldering"
2 "Cleaning"
3 "Embedding of
capacitors in finished
assemblies"
Page 16 of 21
Page 17 of 21
C
A
C
C
CR
C
C/C
C/CR
dt
t
T
tan
V
dV/dt
V/t
E
ESL
ESR
f
f1
f2
fr
FD
FT
i
IC
English
Heat transfer coefficient
Temperature coefficient of capacitance
Capacitor surface area
Humidity coefficient of capacitance
Capacitance
Rated capacitance
Absolute capacitance change
Relative capacitance change (relative
deviation of actual value)
Capacitance tolerance (relative deviation
from rated capacitance)
Time differential
Time interval
Absolute temperature change
(self-heating)
Absolute change of dissipation factor
Absolute voltage change
Time differential of voltage function (rate
of voltage rise)
Voltage change per time interval
Activation energy for diffusion
Self-inductance
Equivalent series resistance
Frequency
Frequency limit for reducing permissible
AC voltage due to thermal limits
German
Wrmebergangszahl
Temperaturkoeffizient der Kapazitt
Kondensatoroberflche
Feuchtekoeffizient der Kapazitt
Kapazitt
Nennkapazitt
Absolute Kapazittsnderung
Relative Kapazittsnderung (relative
Abweichung vom Ist-Wert)
Kapazittstoleranz (relative Abweichung
vom Nennwert)
Differentielle Zeit
Zeitintervall
Absolute Temperaturnderung
(Selbsterwrmung)
Absolute nderung des Verlustfaktors
Absolute Spannungsnderung
Differentielle Spannungsnderung
(Spannungsflankensteilheit)
Spannungsnderung pro Zeitintervall
Aktivierungsenergie zur Diffusion
Eigeninduktivitt
Ersatz-Serienwiderstand
Frequenz
Grenzfrequenz fr thermisch bedingte
Reduzierung der zulssigen
Wechselspannung
Frequency limit for reducing permissible Grenzfrequenz fr strombedingte
AC voltage due to current limit
Reduzierung der zulssigen
Wechselspannung
Resonant frequency
Resonanzfrequenz
Thermal acceleration factor for diffusion Therm. Beschleunigungsfaktor zur
Diffusion
Derating factor
Deratingfaktor
Current (peak)
Stromspitze
Category current (max. continuous
Kategoriestrom (max. Dauerstrom)
current)
Page 18 of 21
Symbol
IRMS
iz
k0
LS
0
test
Pdiss
Pgen
Q
R
R
Ri
Rins
RP
RS
S
t
T
tan
tan D
tan P
tan S
TA
Tmax
Tmin
tOL
Top
TR
Tref
tSL
VAC
English
(Sinusoidal) alternating current,
root-mean-square value
Capacitance drift
Pulse characteristic
Series inductance
Failure rate
Constant failure rate during useful
service life
Failure rate, determined by tests
Dissipated power
Generated power
Heat energy
Density of water vapor in air
Universal molar constant for gases
Ohmic resistance of discharge circuit
Internal resistance
Insulation resistance
Parallel resistance
Series resistance
severity (humidity test)
Time
Temperature
Time constant
Dissipation factor
Dielectric component of dissipation
factor
Parallel component of dissipation factor
Series component of dissipation factor
Ambient temperature
Upper category temperature
Lower category temperature
Operating life at operating temperature
and voltage
Operating temperature
Rated temperature
Reference temperature
Reference service life
AC voltage
German
(Sinusfrmiger) Wechselstrom
Inkonstanz der Kapazitt
Impulskennwert
Serieninduktivitt
Ausfallrate
Konstante Ausfallrate in der
Nutzungsphase
Experimentell ermittelte Ausfallrate
Abgegebene Verlustleistung
Erzeugte Verlustleistung
Wrmeenergie
Dichte von Wasserdampf in Luft
Allg. Molarkonstante fr Gas
Ohmscher Widerstand des
Entladekreises
Innenwiderstand
Isolationswiderstand
Parallelwiderstand
Serienwiderstand
Schrfegrad (Feuchtetest)
Zeit
Temperatur
Zeitkonstante
Verlustfaktor
Dielektrischer Anteil des Verlustfaktors
Parallelanteil des Verlfustfaktors
Serienanteil des Verlustfaktors
Umgebungstemperatur
Obere Kategorietemperatur
Untere Kategorietemperatur
Betriebszeit bei Betriebstemperatur und
-spannung
Beriebstemperatur
Nenntemperatur
Referenztemperatur
Referenz-Lebensdauer
Wechselspannung
Page 19 of 21
Symbol
VC
VC,RMS
English
Category voltage
Category AC voltage
VCD
Vch
VDC
VFB
Vi
Vo
Vop
Vp
Vpp
VR
VRMS
German
Kategoriespannung
(Sinusfrmige)
Kategorie-Wechselspannung
Teilentlade-Einsatzspannung
Ladespannung
Gleichspannung
Spannung (Flyback)
Eingangsspannung
Ausgangssspannung
Betriebsspannung
Impuls-Spitzenspannung
Spannungshub
Nennspannung
Amplitude der Nenn-Wechselspannung
VSC
Vsn
Impedance
Lead spacing
Rasterma
(Sinusfrmige) Wechselspannung
Page 20 of 21
Important notes
Page 21 of 21