Académique Documents
Professionnel Documents
Culture Documents
Edition 28/06/2007
Identification no:
02 08 01 02 014 0 000007
Sikafloor-262 AS N
Sikafloor-262 AS N
Construction
Uses
Characteristics /
Advantages
Test
Approval / Standards
Product Data
Form
Appearance / Colours
Resin - part A:
Hardener - part B:
coloured, liquid
transparent, liquid
Sikafloor-262 AS N
1/7
Packaging
Part A:
Part B:
Part A+B:
21 kg containers
4 kg containers
25 kg ready to mix units
Storage
Storage Conditions /
Shelf-Life
Technical Data
Chemical Base
Epoxy
Density
Part A:
Part B:
Mixed resin:
Filled resin 1 : 0.4 :
~ 1.69 kg/l
~ 1.03 kg/l
~ 1.53 kg/l
~ 1.74 kg/l
Electrostatic Behaviour
Resistance to earth RE
< 10
Mechanical / Physical
Properties
Compressive Strength
(EN 196-1)
(EN 196-1)
Resin: ~ 80 N/mm
Flexural Strength
Resin: ~ 40 N/mm
Bond Strength
Shore D Hardness
77
Abrasion Resistance
(failure in concrete)
(ISO 4624)
(3 days / +23C)
(DIN 53 505)
(DIN 53 109 (Taber Abrader Test))
Resistance
Chemical Resistance
Resistant to many chemicals. Please ask for a detailed chemical resistance table.
Thermal Resistance
Exposure*
Dry heat
Permanent
+50C
Short-term max. 7 d
+80C
Short-term max. 2 h
+100C
System
Information
System Structure
Primer:
Earthing connection:
Conductive coat:
Conductive wearing course:
Note: This system configuration must be fully complied with as described and may
not be changed.
Sikafloor-262 AS N
2/7
Application Details
Consumption / Dosage
Coating System
Product
Consumption
Primer
Levelling (optional)
Conductive coat
Sikafloor -220 W
Conductive
Sikafloor -262 AS N
Wearing course smooth
(Film thickness ~ 1.5 mm) filled with quartz sand
0.1 - 0.3
Sikafloor -262 AS N +
Wearing course textured
Extender T +
(Film thickness ~ 0.5 mm)
Thinner C
These figures are theoretical and does not allow for any additional material required
due to surface porosity, surface profile, variations in level and wastage etc.
Substrate Quality
Substrate Preparation
Application
Conditions /
Limitations
Substrate Temperature
Ambient Temperature
Substrate Humidity
Dew Point
Beware of condensation!
The substrate and uncured floor must be at least 3C above dew point to reduce
the risk of condensation or blooming on the floor finish.
Sikafloor-262 AS N
3/7
Application
Instructions
Mixing
Mixing Time
Prior to mixing, stir part A mechanically. When all of part B has been added to part
A, mix continuously for 2 minutes until a uniform mix has been achieved.
When parts A and B have been mixed, add the quartz sand 0.1 - 0.3 mm and mix
for a further 2 minutes until a uniform mix has been achieved.
To ensure thorough mixing pour materials into another container and mix again to
achieve a consistent mix.
Over mixing must be avoided to minimize air entrainment.
Mixing Tools
Sikafloor -262 AS N must be thoroughly mixed using a low speed electric stirrer
(300 - 400 rpm) or other suitable equipment.
Application Method /
Tools
Prior to application, confirm substrate moisture content, r.h. and dew point.
If > 4% pbw moisture content, Sikafloor EpoCem may be applied as a T.M.B.
(temporary moisture barrier) system.
Levelling:
Rough surfaces need to be levelled first because varying thickness of the
Sikafloor -262 AS N (unfilled) is applied with a serrated trowel and then back-rolled
(crosswise) with a textured roller.
Cleaning of Tools
Clean all tools and application equipment with Thinner C immediately after use.
Hardened and/or cured material can only be removed mechanically.
Potlife
Waiting Time /
Overcoatability
Temperatures
Time
+10C
~ 40 minutes
+20C
~ 25 minutes
+30C
~ 15 minutes
Minimum
Maximum
+10C
24 hours
7 days
+20C
15 hours
5 days
+30C
10 hours
4 days
Sikafloor-262 AS N
4/7
Notes on Application /
Limitations
Number of measurements
< 10 m
1 measurement / m
10-100 m
10 - 20 measurements
> 100 m
10 measurements / 100m
The measuring points must have a distance of at least 50 cm to the next measuring
point. In case of a measurement lower/higher than required, an additional
measurement has to be carried out within 50 cm of the point with the insufficient
result.
Placing of earthing points:
For exact colour matching, ensure the Sikafloor -262 AS N in each area is applied
from the same control batch numbers.
Sikafloor-262 AS N
5/7
Curing Details
Applied Product ready
for use
Temperature
Foot traffic
Light traffic
Full cure
+10C
~ 3 days
~ 6 days
~ 10 days
+20C
~ 2 days
~ 4 days
~ 7 days
+30C
~ 24 hours
~ 2 days
~ 5 days
Note: Times are approximate and will be affected by changing ambient conditions.
Cleaning /
Maintenance
Methods
To maintain the appearance of the floor after application, Sikafloor -262 AS N must
have all spillages removed immediately and must be regularly cleaned using rotary
brush, mechanical scrubbers, scrubber dryer, high pressure washer, wash and
vacuum techniques etc. using suitable detergents and waxes.
Value Base
All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Local Restrictions
Please note that as a result of specific local regulations the performance of this
product may vary from country to country. Please consult the local Product Data
Sheet for the exact description of the application fields.
For information and advice on the safe handling, storage and disposal of chemical
products, users should refer to the most recent Material Safety Data Sheet
containing physical, ecological, toxicological and other safety-related data.
Legal Notes
Sikafloor-262 AS N
6/7
Note
CE Labelling
The harmonized European Standard EN 13 813 Screed material and floor screeds
- Screed materials - Properties and requirements specifies requirements for screed
materials for use in floor construction internally.
Structural screeds or coatings, i.e. those that contribute to the load bearing capacity
of the structure, are excluded from this standard.
Resin floor systems as well as cementitious screeds fall under this specification.
They have to be CE-labelled as per Annex ZA. 3, Table ZA.1.5 and 3.3 and fulfil the
requirements of the given mandate of the Construction Products Directive (89/106):
Construction
*)
07 1)
EN 13813 SR-B1,5-AR1-IR 4
Resin screed/coating for indoors in buildings
(systems as per Product Data Sheet)
Reaction to fire:
Efl 2)
SR
Water permeability:
NPD 2)
Abrasion Resistance:
AR1
Bond strength:
B 1,5
Impact Resistance:
IR 4
Sound insulation:
NPD
Sound absorption:
NPD
Thermal resistance:
NPD
Chemical resistance:
NPD
1)
Last two digits of the year in which the marking was affixed.
2)
3)
No performance determined.
4)
*)
EU Regulation 2004/42
VOC Decopaint
Directive
4)
Sika Services AG
Tffenwies 16
CH-8048 Zurich
Switzerland
Phone
+41 44 436 40 40
Telefax +41 44 436 46 86
wwww.sika.com
Sikafloor-262 AS N
7/7