Académique Documents
Professionnel Documents
Culture Documents
27. When items are being fabricated for very high integrity applications welding inspectors
should make checks
a. before, during and after welding
b. before welding only
c. after welding only
d. during welding and after welding only
28. A code of practice is
a. a standard for workmanship quality only
b. a set of rules and guidelines for manufacturing a specific product
c. a specification for the finished product
d. all of the above
29. For fillet welds, it is normal practice in the UK & USA to measure..
a. throat thicknesses
b. leg lengths
c. penetration depths
d. both a & c
30. A fillet weld has an actual throat thickness of 8mm and a leg length of 7mm. What is the
excess weld metal?
a. 2.1 mm
b. 1.8 mm
c. 3.1 mm
d. 1.4 mm
31. The fusion boundery of a weld is..
a. the boundary between the weld metal and HAZ
b. the boundary between individual weld runs
c. the depth of root penetration
d. the boundary between the HAZ and parent material
32. BS EN 970 allows the use of a magnifying glass for visual inspection but recommends
that the magnification is.
a. x2
b. x2 to x5
c. x5 to x10
d. not greater than x20
33. EN 288 is a specification for
a. welder approval/qualification
b. welding equipment calibration
c. welding procedure approval/qualification
d. consumables for MMA electrodes
34. When 2 different material types are welded together, the joint may be referred to as..
a. a composite joint
b. a transition joint
c. a dissimilar metal joint
d. either b or c
35. A fusible insert is:
a. filler material placed in the weld joint before welding
b. permanent backing strip
c. the core wire in a manual metal arc welding electrode
d. applicable only to bracing
45. When visually inspecting a fillet weld, it would normally be sized by:
a. the leg lengths
b. the actual throat thickness
c. the design throat thickness
d. both a & c
46. Code of practice is:
a. A standard for workmanship only
b. a set of rules for manufacturing a specific product
c. levels of acceptability of a weldment
d. none of the above
47. A welding inspector's main attribute includes:
a. knowledge and experience
b. literacy
c. honesty and integrity
d. all of the above
48. The correct term for a joint prepared on one component only is:
a. a bevel butt
b. a J butt
c. a K butt
d. all of the above
49. Technically a code of practice is:
a. a standard
b. a set of rules for the manufacturing of a product
c. related to welder and weld procedure approval
d. all of the above
50. The correct term of cap height is:
a. reinforcement
b. cap profile height
c. excessive weld metal
d. all of the above
51. The toes of the cap on a butt weld:
a. must overlap on the external surface of a pipe or plate by at least 1.5 mm
b. must be grounded
c. must never be grounded
d. none of the above
52. Which of the following butt weld preparations is generally most susceptible to lack of side
wall fusion during MMA welding?
a. a "U" preparation
b. a "V" preparation
c. a double V preparation
d. lack of side wall fusion does not exist with MMA
53. What is the leg length of a fillet weld
a. the distance from the toe to the face
b. the distance from the root and to the face center
c. the distance from the root to the toe
d. the distance from toe to toe
Q. No.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
ANSWER Q. No.
C
D
B
D
D
C
B
B
B
A
D
C
C
B
C
C
D
C
B
C
C
C
D
D
A
D
A
B
B
C
A
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
ANSWER
B
C
C
A
C
A
C
A
B
C
D
A
B
A
B
D
D
B
A
D
A
C
B
C
B
D
C
B
D
A
B