Académique Documents
Professionnel Documents
Culture Documents
ANSA v13.x
ANSA
version 13.x
2009-12-01
ANSA v13.x
GENERAL REMARKS
1. How to determine parameters of keywords specified with names.
Generally in ANSA, the names of such parameters can be specified through the Name field of all cards that
the names have meaning.
For instance, the name of NAME parameter of
*AMPLITUDE keyword can be specified through
the NAME field as shown in the figure at the left
side.
Then, the result that is taken during output (in *.inp file):
*AMPLITUDE, NAME=TIME_MAGNITUDE, DEFINITION=TABULAR, SMOOTH=.25,
VALUE=RELATIVE, TIME=STEP TIME
.0, .0, 1, 1.
The prefixes of the keywords that ANSA supports are listed in ANSA.defaults file:
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
#
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
Abaqus.NamePrefix
ANSA v13.x
COHESIVE_SECTION = P
CONNECTOR BEHAVIOR = M
CONNECTOR_DERIVED_COMPONENT = D
CONNECTOR_DERIVED_COMPONENT (MatDB) = D
CONNECTOR_SECTION = P
CONTACT_CLEARANCE = CL
CONTACT_PAIR = T
CONTINUUM_SHELL_SECTION = P
COUPLING = C
CUTTING_SURFACE = C
DASHPOT_PROP = P
FASTENER_PROPERTY = P
FILTER = F
FLUID BEHAVIOR = M
FLUID CAVITY = FC
FLUID EXCHANGE = FE
FLUID EXCHANGE ACTIVATION =
FLUID EXCHANGE PROPERTY = FEP
FLUID INFLATOR = FI
FLUID INFLATOR PROPERTY = FEP
GAP_PROP = P
GASKET BEHAVIOR = M
GASKET_SECTION = P
INTERACTION_OUTPUT = I
JOINT_PROP = P
LOAD CASE =
MATERIAL = M
ORIENTATION_C = O
ORIENTATION_NODES_C = O
ORIENTATION_NODES_DYN = O
ORIENTATION_NODES_R = O
ORIENTATION_NODES_S = O
ORIENTATION_R = O
ORIENTATION_S = O
SECTION_CONTROL = C
SET =
SHELL_SECTION = P
SOLID_SECTION = P
SPRING_PROP = P
STEP =
SURFACE = S
SURFACE_INTERACTION = I
SURFACE_SECTION = P
TRUSS_PROP = P
Thus for the above example, the NAME of *AMPLITUDE will have the following format during output:
*AMPLITUDE, NAME=A1;TIME_MAGNITUDE, DEFINITION=TABULAR, SMOOTH=.25,
VALUE=RELATIVE, TIME=STEP TIME
.0, .0, 1., 1.
The user is able to give own prefixes if un-comment the desired Abaqus.NamePrefixes (remove the # symbol at
the start of the line) and type any name after equal symbol of each Abaqus.NamePrefix (up to four characters
can be specified). In example:
# ABAQUS names' prefix library
# Leave lines in comments, for ANSA to assign default prefixes.
Abaqus.NamePrefix AMPLITUDE = TIMG.
In this case, the name of NAME parameter will have the following format during output (have in mind that
Preserve Ids in Names flag of ABAQUS Output Parameters window should be active):
BETA CAE Systems S.A.
ANSA v13.x
ANSA v13.x
Density
T emperature values
ANSA v13.x
NOTES:
Each row implies one data line during output.
The values of each property are specified in each column. The temperature values are always specified in the
last column of the table.
----------------- PYRAMIDS
ANSA v13.x
ANSA v13.x
4. Usage of ANSA tooltips and function finder for any ABAQUS keyword and subsequent parameters
identification.
4.1 Tooltips
The tooltips are very useful in order to understand
which is the usage of the fields and menus inside a
card. For instance the card in the right figure shows
all parameters concerning the *BOUNDARY
keyword. If putting the mouse cursor upon a field
or menu, detailed information will appear. The
information is written in the same manner as in
ABAQUS keywords reference manual and so the
user is not needed to switch to ABAQUS manual.
In this case if putting the cursor on OP menu, all
details of OP parameter are introduced. Thus,
tooltips are useful to identify easily and fast the
keywords and subsequent parameters.
ANSA v13.x
5. Orientation of Surfaces
All orientable elements (e.g. Shell, Gasket, Continuum Shell, etc) and the respective Properties contained
in SETs, can be given a particular Orientation (SPOS / SNEG). This is a characteristic of the Set and can be
assigned per contained entity, i.e a Shell property defined as Oriented= SPOS in one Set can be
Oriented=SNEG in a different Set. Also two Properties in a Set can have different Orientation.
The orientation of the exported surface, based on the Set (Output as surface), is specified either by the
ORIENTATION type or by the Entity's Orientation that is now available.
In order to define the orientation on a set's contained entity:
- Open the SET management window and click on Set's contents that need to specify Orientation.
- The Database Browser List with these entities (e.g. Properties) appear with the Column Oriented. This
appears as an option within the Entity's card as well. However, the field/column becomes available only
through the Set management.
- Using Quick Modify you can change the field directly in the list.
ANSA v13.x
- The Entities assigned orientation are listed under the ORIENTED section
ANSA v13.x
Keyword
*ACOUSTIC MEDIUM
Created by
Remarks
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *BRITTLE CRACKING option to be written to the output file (.inp).
Keyword
Created by
*AMPLITUDE
AUXILIARIES>AMPLTD>NEW.
Pressing the ? key in AMP, AMPLITUDE and FILM AMPL fields of any BOUNDARY,
LOAD and TEMPERATURE card. Then, AMPLITUDE card opens and any amplitude can
be defined by clicking the NEW button.
Remarks
The NAME parameter can be specified through the NAME field (behind the 'ID' field) of
AMPLITUDE card. See also GENERAL REMARKS how to determine the name of NAME
parameter.
The INPUT parameter is not supported. However, there is an alternative way by reading the data
lines from a file by clicking the 'Read' button through AMPLITUDE card and choosing the
particular file from the Open window.
The SCALEX, SCALEY, SHIFTX and SHIFTY parameters are exported only if 'Output Format'
menu is switched to 6.7 or 6.8 during output.
10
Keyword
ANSA v13.x
*AXIAL
Created by
Remarks
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *AXIAL option to be written to the output file (.inp).
Switch 'AX behavior' to ELASTIC and 'AX variation' to LINEAR to define the corresponding
options.
All the properties (stiffness, axial force, strain etc.) are given in a tabular form through AX D.
TABLE field (Press the ? key in AX D. TABLE field to define the corresponding table, if
LINEAR option is specified the above field appears by setting AX DEP option to YES).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
11
ANSA v13.x
Keyword
Created by
Remarks
The ELSET parameter can be specified through the Name field of BEAM SECTION &
ELEMENT TYPE [BEAM SECTION] card. See also GENERAL REMARKS how to determine
the name of ELSET parameter.
The sectoral moment G0 and warping constant Gw are available only when B31OS or B310SH
element types are chosen from BEAM SECTION & ELEMENT TYPE [BEAM SECTION]
card.
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *BEAM GENERAL SECTION option to be written
to the output file (.inp).
Keyword
*BEAM SECTION
Created by
Remarks
The ELSET parameter can be specified through the Name field of BEAM SECTION &
ELEMENT TYPE [BEAM SECTION] card. See also GENERAL REMARKS how to determine
the name of ELSET and MATERIAL parameters.
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *BEAM SECTION option to be written to the output
file (.inp).
12
Keyword
Created by
ANSA v13.x
Remarks
Each row of the specified data table implies one data line during output.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *BIAXIAL TEST DATA option to be written to the output file (.inp).
Keyword
Created by
*BLOCKAGE
2.
3.
Press
OK
in
SURFACE
INTERACTION/CONTACT
[SURFACE_INTERACTION] card to declare the definition.
PROPERTIES
Remarks
13
Keyword
Created by
ANSA v13.x
*BOUNDARY
BOUNDARY>BOUNDARY>Node.
BOUNDARY>BOUNDARY>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
node set names.
If 'Boundary' flag into RESET region of STEP card is active, all *BOUNDARY options in this
step acquire OP=NEW parameter.
Up to 16 degrees of freedom are supported. The dofs are specified in DOF field of *BOUNDARY
[BOUNDARY] card. The values should be given in format 123456789 for up to 9 dof and
separated by comma when greater than 9 is needed e.g. 1,2,3,11.
Keyword
*BRITTLE CRACKING
Created by
Remarks
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Since the above keyword is valid only for a Abaqus/Explicit analysis in order to output the
'Abaqus/Explicit output' flag of Other Options section of Miscellaneous tab should be activated
during output (ABAQUS Output Parameters window). If *DYNAMIC, EXPLICIT ANALYSIS is
selected from STEP card (AUXILIARIES>STEP>NEW) then the above flag is automatically
activated.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *BRITTLE CRACKING option to be written to the output file (.inp).
14
Keyword
ANSA v13.x
*BRITTLE FAILURE
Created by
Remarks
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Since the above keyword is valid only for a Abaqus/Explicit analysis in order to output the
'Abaqus/Explicit output' flag of Other Options section of Miscellaneous tab should be activated
during output (ABAQUS Output Parameters window). If *DYNAMIC, EXPLICIT ANALYSIS is
selected from STEP card (AUXILIARIES>STEP>NEW) then the above flag is automatically
activated.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *BRITTLE FAILURE option to be written to the output file (.inp).
Keyword
*BRITTLE SHEAR
Created by
Remarks
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Since the above keyword is valid only for a Abaqus/Explicit analysis in order to output the
'Abaqus/Explicit output' flag of Other Options section of Miscellaneous tab should be activated
during output (ABAQUS Output Parameters window). If *DYNAMIC, EXPLICIT ANALYSIS is
selected from STEP card (AUXILIARIES>STEP>NEW) then the above flag is automatically
activated.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *BRITTLE SHEAR option to be written to the output file (.inp).
15
Keyword
ANSA v13.x
*BUCKLE
Created by
Using AUXILIARIES>STEP>NEW and selecting the *BUCKLE option into the pull down menu
of ANALYSIS section.
Remarks
Keyword
*BULK VISCOSITY
Created by
Remarks
Switch ANAYSIS to DYNAMIC, EXPLICIT in order to make active *BULK VISCOCITY button
(the keyword is valid only in an Abaqus/Explicit analysis).
16
ANSA v13.x
Keyword
*CAPACITY
Created by
Remarks
Set DEFINED option to YES (located at the top of FLUID BEHAVIOR [FLUID BEHAVIOR]
card) so as the specific *CAPACITY option to be written to the output file (.inp).
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Keyword
Created by
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *CAST IRON COMPRESSION HARDENING option to be written to the output file
(.inp).
Keyword
Created by
17
Remarks
ANSA v13.x
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *CAST IRON PLASTICITY option to be written to the output file (.inp).
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column (Press the ? key in TEST DATA field to define the corresponding
table). DEPENDENCIES parameter is supported if the data table defined in above manner contains
other columns after the 'Temperature' one. The number of these columns (var(i)) determines the
number of DEPEDENCIES parameter.
Keyword
Created by
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *CAST IRON TENSION- HARDENING option to be written to the output file (.inp).
Keyword
Created by
*CENTROID
Remarks
18
Keyword
Created by
ANSA v13.x
*CFLUX
LOADs>CFLUX>Node.
LOADs>CFLUX>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
node set names.
Up to 13 degrees of freedom may be specified.
If Cflux flag into RESET region of STEP card is active, all *CFLUX options in this step
acquire OP=NEW parameter.
Keyword
*CLEARANCE
Created by
Remarks
Set 'by' menu to VALUE or TABULAR to define VALUE and TABULAR parameters respectively.
In addition if by=TABULAR press CLEARANCE TABULAR DATA button (located at bottom of
*CONTACT DEFINITION [CONTACT PAIR] card) to define the relative parameters
accordingly. Specifically set BOLT to YES to define BOLT parameter, set either 'by' to NODE to
pick a node from screen through NODE field or to SET to select a node set through SET field and
click Insert button to declare the definition (repeat the action to define data lines for different node
or node set).
INPUT parameter is supported only during input.
See GENERAL REMARKS how to determine the names of SLAVE and MASTER parameters.
Keyword
Created by
*CLOAD
LOADs>CLOAD>Node.
LOADs>CLOAD>Set.
LOADs>CLOAD>Dstr.
19
Remarks
ANSA v13.x
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
node set names.
If Cload flag into RESET region of STEP card is active, all *CLOAD options in this step
acquire OP=NEW parameter.
Keyword
Created by
Remarks
*COHESIVE BEHAVIOR
2.
3.
Press
OK
in
SURFACE
INTERACTION/CONTACT
[SURFACE_INTERACTION] card to declare the definition.
PROPERTIES
Set DEP option to YES and press the ? key in D.TABLE field so as to specify the elastic
behaviour as a function of temperature. DEPENDENCIES parameter is supported if the data table
defined in above manner contains other columns after the 'Temperature' one. The number of these
columns (var(i)) determines the number of DEPEDENCIES parameter.
The keyword can be output provided that the 'Output Format' option is switched to 6.8 (ABAQUS
Output Parameters window).
Keyword
*COHESIVE SECTION
Created by
MENUBAR>Windows>Properties>NEW>COHESIVE.
Remarks
See GENERAL REMARKS how to determine the names of ELSET, MATERIAL, CONTROLS
and ORIENTATION parameters.
Set DEFINED option to YES (located at the top of COHESIVE SECTION & ELEMENT TYPE
[COHESIVE_SECTION] card) so as the specific *COHESIVE SECTION option to be written to
the output file (.inp).
20
Keyword
Created by
ANSA v13.x
Remarks
Each row of the specified data table implies one data line during output
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *COMBINED TEST DATA option to be written to the output file (.inp).
Keyword
*CONDUCTIVITY
Created by
Using MENUBAR>Windows>Materials>NEW>MATERIAL
*CONDUCTIVITY option.
and
setting
to
YES
the
Remarks
Set DEP option to YES and press the ? key in DATA TABLE field so as to specify the thermal
conductivity as a function of temperature. For TYPE=ISO a table with 2 columns, for TYPE =
ORTHO a table with 4 columns and for TYPE=ANISO a table with 7 columns should be defined.
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *CONDUCTIVITY option to be written to the output file (.inp).
Keyword
Created by
*CONNECTOR BEHAVIOR
MENUBAR>Windows>Materials>NEW>CONNECTOR BEHAVIOR.
21
Remarks
ANSA v13.x
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR BEHAVIOR option to be written to the
output file (.inp). In order to avoid the above, activate either the 'set default' or 'set default for
prop=CONNECTOR_SECTION' options of an already existing CONNECTOR BEHAVIOR in
MATDB. Then when creating a new CONNECTOR BEHAVIOR or a CONNECTOR SECTION
respectively, this will take the properties of the CONNECTOR BEHAVIOR in MATDB and the
DEFINED=YES automatically.
The NAME parameter can be specified through the Name field of CONNECTOR BEHAVIOR
[CONNECTOR BEHAVIOR] card. See also GENERAL REMARKS how to determine the name
of NAME parameter.
Keyword
Created by
Remarks
The reference lengths and angles can be defined through CNRF>data field (press ? key and then
the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card to specify the corresponding
fields of the lengths and angles).
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR CONSTITUTIVE REFERENCE option to
be written to the output file (.inp).
Keyword
Created by
Remarks
The attributes of the *CONNECTOR DAMAGE EVOLUTION can be defined through DI>data
field (press ? key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
if DI>comp=YES then activate one of the COMP of *DAMAGE INITIATION to define
*DAMAGE EVOLUTION (*CONNECTOR DAMAGE INITIATION card).
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column in each selected TYPE and SOFTENING respectively (Press the
? key in DATA TABLE field to define the corresponding table). DEPENDENCIES parameter is
supported if the data table defined in above manner contains other columns after the 'Temperature'
one. The number of these columns (var(i)) determines the number of DEPEDENCIES parameter.
22
ANSA v13.x
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR DAMAGE EVOLUTION option to be
written to the output file (.inp).
Keyword
Created by
Remarks
Switch to YES or NO the DI>comp option to include or not the COMPONENT parameter.
The attributes of the *CONNECTOR DAMAGE INITIATION can be defined through DI>data
field (press ? key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column in each selected CRITERION respectively (Press the '?' key in
DATA TABLE field to define the corresponding table). DEPENDENCIES parameter is supported
if the data table defined in above manner contains other columns after the 'Temperature' one. The
number of these columns (var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR DAMAGE INITIATION option to be
written to the output file (.inp).
Keyword
*CONNECTOR DAMPING
Created by
Remarks
The attributes of the *CONNECTOR DAMPING can be defined through D>data field (press ?
key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column in each case (Press the ? key in DATA TABLE field to define the
corresponding table). If the 21 damping constants are specified as a function of temperature, the
values should be given in a table with 22-columns. DEPENDENCIES parameter is supported if the
data table defined in above manner contains other columns after the 'Temperature' one. The number
of these columns (var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
23
ANSA v13.x
Keyword
Created by
AUXILIARIES>DRV COMP>NEW.
Following the steps below:
1. Use MENUBAR>Windows>Materials>NEW>CONNECTOR BEHAVIOR and set to
YES the *DAMAGE INITIATION option.
2. Press the ? key in DI>data field (having DI>comp=NO) and then the NEW button in
CONNECTOR BEHAVIOR ATTRIBUTE card.
3. Press the ? key in *POTENTIAL field and then the NEW button in CONNECTOR
BEHAVIOR ATTRIBUTE card
4. Switch one of the six Comp/Drv options to DRV.COMP. and then press the ? key in
drv.comp. field.
5. Press the NEW button in CONNECTOR DERIVED COMPONENT HELP card.
Follow the same procedure for *DAMAGE EVOLUTION, *FRICTION and *PLASTICITY
options as well.
Remarks
The NAME parameter can be specified through the Name field of CONNECTOR DERIVED
COMPONENT [CONNECTOR_DERIVED_ COMPONENT] card. See also GENERAL
REMARKS how to determine the name of NAME parameter.
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column in each case (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR DERIVED COMPONENT option to be
written to the output file (.inp).
OPERATOR=MACAULEY SUM is exported only if 'Output Format' menu is switched to 6.7 or
6.8 during output.
Keyword
Created by
*CONNECTOR ELASTICITY
24
Remarks
ANSA v13.x
The attributes of the *CONNECTOR ELASTICITY can be defined through EL>data field (press
? key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column in each case (Press the ? key in DATA TABLE field to define the
corresponding table). If the 21 elasticity constants are specified as a function of temperature, the
values should be given in a table with 22-columns. DEPENDENCIES parameter is supported if the
data table defined in above manner contains other columns after the 'Temperature' one. The number
of these columns (var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR ELASTISITY option to be written to the
output file (.inp).
Keyword
*CONNECTOR FAILURE
Created by
Remarks
The attributes of the *CONNECTOR FAILURE can be defined through F>data field (press ?
key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR FAILURE option to be written to the output
file (.inp).
Keyword
*CONNECTOR FRICTION
Created by
Remarks
Switch to YES or NO the FR>comp option to include or not the COMPONENT parameter.
The attributes of the *CONNECTOR FRICTION can be defined through FR>data field (press ?
key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card to specify the
parameters as desired in CONNECTOR FRICTION [CONNECTOR_BEHAVIOR_ATTRIBUTE]
card).
25
ANSA v13.x
The temperature values may be specified only if DEP parameter is set to YES (available when
PREDEFINED option set to NO or FR>comp option is set to YES). They are introduced in the
last column in each case (Press the '?' key in DATA TABLE field to define the corresponding
table). DEPENDENCIES parameter is supported if the data table defined in above manner contains
other columns after the 'Temperature' one. The number of these columns (var(i)) determines the
number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR FRICTION option to be written to the
output file (.inp).
Keyword
Created by
*CONNECTOR HARDENING
Remarks
The temperature values may be specified only if DEP parameter is set to YES. They are
introduced in the last column in each case (Press the ? key in DATA TABLE field to define the
corresponding table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR HARDENING option to be written to the
output file (.inp).
Keyword
Created by
*CONNECTOR LOAD
LOADs>CONN.LOAD>Element.
LOADs>CONN.LOAD>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
element set names.
If Connector Load flag into RESET region of STEP card is active, all *CONNECTOR LOAD
26
ANSA v13.x
Keyword
*CONNECTOR LOCK
Created by
Remarks
The attributes of the *CONNECTOR LOCK can be defined through LCK>data field (press ?
key and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR LOCK option to be written to the output
file (.inp).
Keyword
Created by
*CONNECTOR MOTION
BOUNDARY>CON.MOTION>Element.
BOUNDARY>CON.MOTION>Set.
Remarks
The AMPLITUDE parameter can be specified through AMP field (access to the AMPLITUDE
card by pressing the ? key). See GENERAL REMARKS how to determine the name of
AMPLITUDE parameter as well as the element set names.
If Connector Motion flag into RESET region of STEP card is active, all *CONNECTOR
MOTION options in this step acquire OP=NEW parameter.
Keyword
*CONNECTOR PLASTICITY
Created by
Remarks
Switch to YES the PL>comp option to include the COMPONENT parameter and select the
connector's component of relative motion for which plasticity behavior is specified through
27
ANSA v13.x
FR>data field (press ? key and then the NEW button in CONNECTOR BEHAVIOR
ATTRIBUTE card).
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR PLASTICITY option to be written to the
output file (.inp).
Keyword
Created by
*CONNECTOR POTENTIAL
Remarks
Keyword
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR POTENTIAL option to be written to the
output file (.inp).
*CONNECTOR SECTION
Created by
MENUBAR>Windows>Properties>NEW>CONNECTOR.
Remarks
The ELSET and BEHAVIOR parameters can be specified through the Name and MID fields of
*CONNECTOR SECTION [CONNECTOR_ SECTION] card respectively. See also GENERAL
REMARKS how to determine the names of ELSET, BEHAVIOR, CONTOLS parameters and the
orientation names.
Set DEFINED option to YES (located at the top of *CONNECTOR SECTION
[CONNECTOR_SECTION] card) so as the specific *CONNECTOR SECTION option to be
28
ANSA v13.x
Keyword
*CONNECTOR STOP
Created by
Remarks
The attributes of the *CONNECTOR STOP can be defined through STP>data field (press ? key
and then the NEW button in CONNECTOR BEHAVIOR ATTRIBUTE card).
Set DEFINED option to YES (located at the top of CONNECTOR BEHAVIOR [CONNECTOR
BEHAVIOR] card) so as the specific *CONNECTOR STOP option to be written to the output file
(.inp).
Keyword
Created by
*CONSTRAINT CONTROLS
NEW
to
define
Remarks
Keyword
The DELETE SLAVE parameter is written out provided the 'Output Format' is set to 6.7 or 6.8
(ABAQUS Output Parameters window).
*CONTACT
Created by
Remarks
If Contact flag into RESET region of STEP card is active, all *CONTACT options in this step
acquire OP=NEW parameter.
29
ANSA v13.x
The keyword is output for Abaqus/Standard provided the 'Output Format' is set to 6.8 (ABAQUS
Output Parameters window) and STEP field is blank or hosts a step id of an Abaqus/Standard
analysis.
Keyword
*CONTACT CLEARANCE
Created by
AUXILIARIES>CLEARANCE>*CONTACT CLEARANCE>NEW.
Remarks
The NAME parameter can be specified through the Name field of *CONTACT CLEARANCE
[CONTACT_CLEARANCE] card. See also GENERAL REMARKS how to determine the name
of NAME parameter.
Keyword
Created by
Remarks
The names of the first and second surface can be specified through the Name fields of the specific
SETS cards. See also GENERAL REMARKS how to determine the names of the first, second
surface and *CONTACT CLEARANCE definition.
The model should also include *CONTACT INCLUSIONS or *CONTACT EXCLUSIONS for the
validation of this keyword (so as to be written out).
Keyword
*CONTACT CONTROLS
Created by
AUXILIARIES>CONTROLS>*CONTACT CONTROLS>NEW.
Remarks
MASTER and SLAVE parameters can be specified by pressing the ? key in CONTACT PAIR
field and selecting an existing contact pair from CONTACT PAIR LIST HELP card (in
Abaqus/Standard). See also GENERAL REMARKS how to determine the names of MASTER and
SLAVE parameters.
30
Keyword
ANSA v13.x
Created by
Remarks
The first and second surface can be specified through the corresponding fields of *CONTACT
CONTROLS ASSIFNMENT [CONTACT CONTROLS ASSIGNMENT] card (press the ? key
to select the proper sets from SETS HELP card). See also GENERAL REMARKS how to
determine the names of the first and second surface.
The model should also include *CONTACT INCLUSIONS or *CONTACT EXCLUSIONS for the
validation of this keyword (so as to be written out).
Leave 'STEP' field blank or specify the step id of a DYNAMIC, EXPLICIT analysis so as to write
out as model and history data respectively. If 'STEP'= blank have in mind to activate the
'Abaqus/Explicit Output' flag during output due to the fact this keyword is valid just for an
ABAQUS/Explicit analysis.
TYPE=FOLD TRACKING and FOLD INVERSION CHECK are written out only if 'Output
Format' menu is set to 6.7 or 6.8 during output. In addition this version (6.7) will affect the format
of AUTOMATIC OVERCLOSURE RESOLUTION parameter according to the ABAQUS manual.
TYPE=ENHANCED EDGE TRACKING is output provided the 'Output Format' menu is set to 6.8
during output.
Keyword
Created by
*CONTACT DAMPING
Remarks
Keyword
Created by
*CONTACT EXCLUSIONS
31
Remarks
ANSA v13.x
The first and second surface can be specified through the SSID and MSID fields respectively
(press the ? key to select existing sets from the SETS HELP card). See also GENERAL
REMARKS how to determine the names of the first and second surface.
Blank slave and master surface names are supported when SLAVE=ALL ELEM and
MASTER=blank respectively. If slave surface is blank then a set with all elements of model is
created during input and this set is assigned to SSID field of current contact (name of set is
SET_PART_ALL and it is marked as auxiliary (AUXILIARY=YES) in order to output contact in
same format which means blank slave surface).
For an Abaqus/Explicit analysis the keyword is output provided the 'Abaqus/Explicit output' flag of
Other Options section of Miscellaneous tab is activated during output (ABAQUS Output
Parameters window). If *DYNAMIC, EXPLICIT ANALYSIS is selected from STEP card
(AUXILIARIES>STEP>NEW) then the above flag is automatically activated. The keyword is
output for Abaqus/Standard provided the 'Output Format' is set to 6.8 (ABAQUS Output
Parameters window) and STEP field is blank or hosts a step id of an Abaqus/Standard analysis.
Keyword
*CONTACT FILE
Created by
Remarks
Specify the SLAVE, MASTER or BOTH surfaces by pressing the? key in the CONTACT field
and selecting an existing contact pair from the corresponding card. Do the same into NSET field
to define the node set for which this output request is being made. The user is able to select more
than one sets at once in order to define more than one output requests quickly. See also GENERAL
REMARKS how to determine the names of SLAVE, MASTER and NSET parameters.
Press the Output Variables button and activate any variable to be written to the results file for this
contact pair. Alternatively, type the identifying keys for the contact variables, separated with
commas, through the corresponding (Identifying Keys) field of CONTACT VARIABLES
window.
Keyword
Created by
*CONTACT INCLUSIONS
32
Remarks
ANSA v13.x
The first and second surface can be specified through the SSID and MSID fields respectively
(press the ? key to select existing sets from the SETS HELP card). See also GENERAL
REMARKS how to determine the names of the first and second surface.
Blank master surface names and ALL ELEMENT BASED parameter are supported when
MASTER is switched to blank and SLAVE to ALL ELEM respectively (*CONTACT
DEFINITION [CONTACT PAIR] card). In addition, ALL EXTERIOR parameter is output when
'Abaqus Version' option of ABAQUS Output Parameters window is is switched to 6.6 or 6.7 or
6.8.
For an Abaqus/Explicit analysis the keyword is output provided the 'Abaqus/Explicit output' flag of
Other Options section of Miscellaneous tab is activated during output (ABAQUS Output
Parameters window). If *DYNAMIC, EXPLICIT ANALYSIS is selected from STEP card
(AUXILIARIES>STEP>NEW) then the above flag is automatically activated. The keyword is
output for Abaqus/Standard provided the 'Output Format' is set to 6.8 (ABAQUS Output
Parameters window) and STEP field is blank or hosts a step id of an Abaqus/Standard analysis.
Keyword
Created by
*CONTACT INTERFERENCE
Remarks
Keyword
Created by
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
slave and master surface names.
*CONTACT OUTPUT
33
Remarks
ANSA v13.x
Specify the SLAVE, MASTER or BOTH surfaces by pressing the'?' key in the CONTACT field
and selecting an existing contact pair from the corresponding card. Do the same into NSET and
SURF (EXPL) fields to specify the NSET and SURFACE parameters respectively (select the
proper set from SETS HELP card). The user is able to select more than one sets at once in order
to define more than one output requests quickly. See also GENERAL REMARKS how to
determine the names of SLAVE, MASTER, NSET and SURFACE parameters.
Press the Output Variables button and activate any variable to be written to the output database for
this contact pair. Alternatively, type the identifying keys for the contact variables, separated with
commas, through the corresponding (Identifying Keys) field of CONTACT VARIABLES
window.
Keyword
Created by
*CONTACT PAIR
Remarks
Specify the slave and master surfaces through the SSID and MSID fields respectively. Do the
same into INTERACTION and ADJUST=NSET fields to specify the INTERACTION and
ADJUST parameters respectively. See also GENERAL REMARKS how to determine the slave,
master surface and node set names as well as the name of INTERACTON parameter.
Set ADJUST to POS_VAL and type a value to adjust the initial positions of the surfaces in the
field that appears or set ADJUST to NSET to define a node set label (press ? key in the
corresponding field and select an existing node set or create a new one through the SETS HELP
window).
Keyword
*CONTACT PRINT
Created by
Remarks
Specify the SLAVE, MASTER or BOTH surfaces by pressing the ? key in the CONTACT field
and selecting an existing contact pair from the corresponding card. Do the same into NSET field
to specify the NSET parameter (select the proper set from SETS HELP card). The user is able to
select more than one sets at once in order to define more than one output requests quickly. See also
GENERAL REMARKS how to determine the names of SLAVE, MASTER and NSET parameters.
34
ANSA v13.x
Press the Output Variables button and activate any variable to be written to the data file for this
contact pair. Alternatively, type the identifying keys for the contact variables, separated with
commas, through the corresponding (Identifying Keys) field of CONTACT VARIABLES
window.
Keyword
Created by
Remarks
See GENERAL REMARKS how to determine the first and second surface names as well as the
name of *SURFACE INTERACTON.
Keyword
*CONTROLS
Created by
AUXILIARIES>CONTROLS>*CONTROLS>NEW.
Remarks
Press '?' key in STEP field to select the step that the current control will reside in.
FIELD= PRESSURE LAGRANGE MULTIPLIER or VOLUMETRIC LAGRANGE
MULTIPLIER are output provided that the 'Output Format' option is switched to 6.7 or 6.8 and for
TYPE=VCCT LINEAR SCALING to 6.8 (ABAQUS Output Parameters window).
Keyword
*COUPLED TEMPERATURE-DISPLACEMENT
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *COUPLED TEMPERATUREDISPLACEMENT option into the pull down menu of ANALYSIS section.
Remarks
35
ANSA v13.x
to YES. The CONTINUE is defined by following the above procedure plus setting CONTINUE
menu to YES. The above parameters are written out provided the 'Output Format' is switched to 6.7
or 6.8 (ABAQUS Output Parameters window).
Keyword
Created by
*COUPLING
Remarks
The CONSTRAIN NAME parameter may be specified in Name field and the ORIENTATION
parameter in ORIENT field of *COUPLING [COUPLING] card. See also GENERAL
REMARKS how to determine the names of CONSTRAIN NAME and ORIENTATION
parameters.
Node set names for REF NODE parameter are supported only during input.
When COUPLING is defined with NODES or FACET options: The SURFACE parameter is
automatically specified with a standard name: SURFACE=SURF_COUPLING_(arbitrary number).
The arbitrary number is a number different than the Id numbers of the existing sets in the model.
The uniqueness of the surface names can be controlled through the
Output_gen_id_range<SET>=min: max option in ANSA.defaults file. The arbitrary number at the
end of the surface name will be a value between the specified min and max of this option.
When COUPLING is defined with SET option: The SURFACE parameter is automatically
specified with the name of the set: SURFACE='set name'.
Keyword
Created by
*CRUSHABLE FOAM
36
Remarks
ANSA v13.x
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *CRUSHABLE FOAM option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in TEST DATA to define the corresponding table
according to the HARDENING parameter). DEPENDENCIES parameter is supported if the data
table defined in above manner contains other columns after the 'Temperature' one. The number of
these columns (var(i)) determines the number of DEPEDENCIES parameter.
Keyword
Created by
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *CRUSHABLE FOAM HARDENING option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in TEST DATA to define the corresponding table).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
Keyword
Created by
Using AUXILIARIES>STEP>*CYCLIC SYM. MODEL and typing a value at N field (the button
is coloured to red to indicate that the current keyword is defined).
Remarks
Leave all fields of *CYCLIC SYMMETRY MODEL card blank to deactivate keyword.
37
ANSA v13.x
Keyword
Created by
*DAMAGE EVOLUTION
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *DAMAGE EVOLUTION option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE (in MATERIAL card) or
D.TABLE (in SURFACE INTERACTION card) to define the corresponding table).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
Keyword
Created by
*DAMAGE INITIATION
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *DAMAGE INITIATION option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table Press the ? key in DATA TABLE (in MATERIAL card) or D.TABLE
(in SURFACE INTERACTION card) to define the corresponding table). DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
38
ANSA v13.x
DEPEDENCIES parameter.
Keyword
Created by
*DAMAGE STABILIZATION
Remarks
Keyword
*DAMPING
Created by
Using MENUBAR>Windows>Materials>NEW>MATERIAL
*DAMPING option.
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *DAMPING option to be written to the output file (.inp).
Keyword
and
setting
to
YES
the
*DASHPOT
Created by
MENUBAR>Windows>Properties>NEW>DASHPOT.
Remarks
The ELSET parameter can be controlled by typing any name in Name field of *DASHPOT
[DASHPOT_PROP] card. The ORIENTATION parameter can be defined by pressing the ? key
in ORIENT field and selecting an existing coordinate system or creating a new one from the
COORDINATES SYSTEM HELP card. See also GENERAL REMARKS how to determine the
names of ELSET and ORIENTATION parameters.
The NONLINEAR parameter can be included if BEHAVIOR is switched to NONLINEAR.
39
ANSA v13.x
Switch between Axial and Fixed Dir. TYPE in order to define dashpot behavior for DASHPOTA
elements or to give degrees of freedom for DASHPOT1 and DASHPOT2 elements respectively.
The temperature values may be specified only if DEP option is set to DEP. They are introduced in
the last column in each case (Press the ? key in C-F-T or F-V-T fields to define the corresponding
table). F-V-T field appear when BEHAVIOR is switched to NONLINEAR. DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of DEPEDENCIES
parameter.
Set DEFINED option to YES (located at the top of *DASHPOT [DASHPOT_PROP] card) so as
the specific *DASHPOT option to be written to the output file (.inp).
Keyword
*DENSITY
Created by
Remarks
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column (Press the ? key in DATA TABLE field to define the Mass Density-Temperature
table). DEPENDENCIES parameter is supported if the data table defined in above manner contains
other columns after the 'Temperature' one. The number of these columns (var(i)) determines the
number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *DENSITY option to be written to the output file (.inp).
Keyword
Created by
*DEPVAR
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] and GASKET
BEHAVIOR [GASKET BEHAVIOR] cards) so as the specific *DEPVAR option to be written to
the output file (.inp).
40
Keyword
Created by
ANSA v13.x
*DFLUX
LOADs>DFLUX>Element.
LOADs>DFLUX>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
element set names.
For sets the option 'Output as: should be switched to Set in order to output *DFLUX keyword.
If Dflux flag into RESET region of STEP card is active, all *DFLUX options in this step
acquire OP=NEW parameter.
Keyword
*DIAGNOSTICS
Created by
Remarks
Switch ANAYSIS to DYNAMIC, EXPLICIT in order to make active *DIAGNOSTICS button (the
keyword is valid only in an Abaqus/Explicit analysis).
The CRITICAL ELEMENTS and DEEP PENETRATION FACTOR parameters are written out
provided the 'Output Format' is switched to 6.7 or 6.8 (ABAQUS Output Parameters window).
Keyword
Created by
*DISTRIBUTING
41
Remarks
Keyword
Created by
ANSA v13.x
The WEIGHTING METHOD parameter is supported if using SET option and switching
SURF.TYPE to ELEMENT-BASED. As an alternative way, fill the Wti fields (or W field when set
of nodes is used) to specify the weighting factors at each coupling node. These factors are written
out in the respective *SURFACE keyword. Especially, when using FACET option the weighting
factors are automatically calculated following the NASTRAN RBE3 distribution theory.
*DISTRIBUTING COUPLING
Remarks
Keyword
Created by
The ELSET parameter is automatically specified with the standard name: DCOUP3D_(eid). Take
control of the ELSET name by changing its eid trough the corresponding field of *COUPLING
[COUPLING] card.
*DISTRIBUTION
A) The most simple way to define the *DISTRIBUTION keyword for thickness:
1. Use MENUBAR>Windows>Database>Database and left click on ELEMENT>SHELL
item.
2. Select existing shell elements from the screen, right click on highlighted items in
Selection list and use Modify option.
3. Create four Modify Rules for t1, t2, t3, and t4 fields and type any value in each of them so
as to define varying thickness in elements (since t4 field does not exist in trias if
above rules are applied on both trias and quads it will be failed for trias. In the
relative window that opens press 'Open In New Tab' button and repeat the procedure
by removing the t4 rule).
4. Activate the Output elements thickness flag in conjunction with - as DISTRIBUTION
option through ABAQUS Output Parameters card during output.
42
ANSA v13.x
B) The most simple way to define the *DISTRIBUTION keyword for orientation:
1. Use MENUBAR>Windows>Database>Database and left click on ELEMENT>SHELL
item.
2. Select existing shell elements from the screen which are referenced by composite or
laminate properties, right click on highlighted items in Selection list and use
Modify option.
3. Switch 'mat.orient' option either to ANGLE and specify a value in ANGLE field or to mcid
and press '?' or 'F1' keys in mcid field to select an existing coordinate system from the
list and screen respectively (SHELL ELEMENT CARD).
Remarks
Keyword
Created by
*DISTRIBUTION TABLE
Remarks
See Remarks of *DISTRIBUTION keyword related to the way of NAME parameter determination.
43
Keyword
Created by
ANSA v13.x
*DLOAD
LOADs>DLOAD>P/PNU/HP>Element.
LOADs>DLOAD>P/PNU/HP>Set.
LOADs>DLOAD>P/PNU/HP>Edge.
LOADs>DLOAD>P/PNU/HP>Dstr.
LOADs>DLOAD>GRAV>Set.
LOADs>DLOAD>VBF>Element.
LOADs>DLOAD>VBF>Set.
LOADs>DLOAD>VP>Element.
LOADs>DLOAD>VP>Set.
LOADs>DLOAD>CENTRIF>Element.
LOADs>DLOAD>CENTRIF>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
element set names.
For sets the option 'Output as: should be switched to Set in order to output *DLOAD keyword.
Since CPE, CPS,CAX, DC2D and DCC2D4 are solid element types but in ANSA they are faced as
shells, use Element or Set of elements options to select big facets and Edge or Set of edges
options to select other facets (thickness facets). For solid types C3D, DC3D, DCC3D and AC3D
when using LOADs>DLOAD>P/PNU/HP or/and VP >Set the set should contain solid facets and
whole solids for all other functions (GRAV, VBF and CENTRIF options) in order to be valid .
If Dload flag into RESET region of STEP card is active, all *DLOAD options in this step
acquire OP=NEW parameter.
Keyword
*DSFLUX
Created by
LOADs>DFLUX>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
surface names.
44
ANSA v13.x
For sets the option 'Output as: should be switched to Surface in order to output *DSFLUX
keyword.
If Dsflux flag into RESET region of STEP card is active, all *DSFLUX options in this step
acquire OP=NEW parameter.
Keyword
Created by
*DSLOAD
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter as well as the
surface names.
The set may contain only facets of solids and continuum shells, shells and edges of shells (S and DS
element types) and solids (CPE, CPS, CAX, DC2D and DCC2D4 element types).
To output the DSLOADs the 'Output as:' option of the set should be set to Surface. Especially for
sets with shell edges the definition of *SURFACEs is done with En labels and *DSLOAD is written
out with EDLD and EDLDNU load types.
If Dsload flag into RESET region of STEP card is active, all *DSLOAD options in this step
acquire OP=NEW parameter.
Keyword
Created by
*DYNAMIC
Use AUXILIARIES>STEP>NEW and then select the *DYNAMIC option into the pull down menu
of ANALYSIS section to perform an Abaqus/Standard analysis.
Use AUXILIARIES>STEP>NEW and then select the *DYNAMIC, EXPLICIT option into the pull
down menu of ANALYSIS section to perform an Abaqus/Explicit analysis.
Remarks
45
ANSA v13.x
Keyword
*ELASTIC
Created by
Remarks
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the '?' key in DATA TABLE field to define the corresponding
table at each TYPE that is used). DEPENDENCIES parameter is supported if the data table defined
in above manner contains other columns after the 'Temperature' one. The number of these columns
(var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *ELASTIC option to be written to the output file (.inp).
Keyword
Created by
*ELEMENT, TYPE=AC3D10
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO> DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
with
Use the above functions to create 10-node quadratic tetras and hence select the AC3D_ type from
the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
46
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=AC3D15
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO> DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order triangular shells.
with
Use the above functions to create 15-node quadratic triangular prisms and hence select the AC3D_
type from the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE
[SOLID_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=AC3D20
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
with
Use the above functions to create 20-node quadratic bricks and hence select the AC3D_ type from
the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
47
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=AC3D4
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
b.
Use the above functions to create 4-node linear tetras and hence select the AC3D_ type from the
TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card that
exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=AC3D6
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs> INFO> DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
d.
Use the above functions to create 6-node linear triangular prisms and hence select the AC3D_ type
from the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
48
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=AC3D8
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs> INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
d.
Use the above functions to create 8-node linear bricks and hence select the AC3D_ type from the
TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card that
exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=AC3D8R
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs> INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
49
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
This element type is valid only in Abaqus/Explicit analyses (Use *DYNAMIC, EXPLICIT through
ANALYSIS pull down menu of STEP card and activate Abaqus/Explicit output flag during
output).
Keyword
Created by
*ELEMENT, TYPE=B31
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of Head, Body or Nut section.
d.
Use any of the above functions to create beams and hence select the B31 type from the TYPE pull
down menu of BEAM SECTION&ELEMENT TYPE [BEAM_SECTION] card that exists in
PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
50
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=B31H
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of Head, Body or Nut section.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=B31OS
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of Head, Body or Nut section.
d.
Use any of the above functions to create beams and hence select the B31 type from the 'TYPE' and
OS from the 'optional1' pulls down menu respectively (BEAM SECTION&ELEMENT TYPE
[BEAM_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
51
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=B31OSH
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of Head, Body or Nut section.
d.
Use any of the above functions to create beams and hence select the B31 type from the 'TYPE', OS
from the 'optional1' and H from the 'optional2' pulls down menu respectively (BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=B33
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of 'Head', 'Body' or 'Nut' section.
Remarks
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
52
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=B33H
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of 'Head', 'Body' or 'Nut' section.
d.
Use any of the above functions to create beams and hence select the B33 type from the 'TYPE' and
H from the 'optional2' pulls down menu respectively (BEAM SECTION&ELEMENT TYPE
[BEAM_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D10
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE' pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card that
exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
53
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D10E
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE' and E from the 'optional3' pull down menus respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D10H
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
d.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE' and H from the 'optional2' pulls down menu respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
54
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D10I
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE' and I from the 'optional1' pull down menu respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D10M
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
d.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE' and M from the 'optional1' pull down menu respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
55
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D10MH
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE', M from the 'optional1' and H from the 'optional2' pulls down menu respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D10MHT
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE', M from the 'optional1', H from the 'optional2' and T from 'optional3' pulls down menu
respectively (SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card located in
PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
56
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D10MT
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the C3D_ type from the
'TYPE', M from the 'optional1' and T from 'optional3' pulls down menu respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D15
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order triangular
shells.
d.
Use the above functions to create 15-node quadratic triangular prisms and hence select the C3D_
type from the 'TYPE' pull down menu of SOLID SECTION&ELEMENT TYPE
[SOLID_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
57
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D15E
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order triangular
shells.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D15H
58
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE' pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20E
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE' and E from the 'optional3' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
59
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20H
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE' and H from the 'optional2' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20HT
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE', H from the 'optional2' and T from 'optional3' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
60
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20R
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE' and R from the 'optional1' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20RE
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE' , R from 'optional1' and E from 'optional3' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
61
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20RH
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE', R from the 'optional1' and H from the 'optional2' pull down menus respectively
(SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20RHT
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE', R from the 'optional1', H from the 'optional2' and T from 'optional3' pull down menus
respectively (SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card located in
PR.LIST).
BETA CAE Systems S.A.
62
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20RT
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE', R from the 'optional1' and T from 'optional3' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D20T
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the C3D_ type from
the 'TYPE' and T from 'optional3' pull down menus respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
63
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D4
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
b.
Use the above functions to create 4-node linear tetras and hence select the C3D_ type from the
'TYPE' pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D4E
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
b.
Use the above functions to create 4-node linear tetras and hence select the C3D_ type from the
'TYPE' and E from the 'optional3' pull down menus respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
64
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=C3D4H
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D4T
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
b.
Use the above functions to create 4-node linear tetras and hence select the C3D_ type from the
'TYPE' and T from the 'optional3' pull down menus respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
65
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=C3D6
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
d.
Use the above functions to create 6-node linear triangular prisms and hence select the C3D_ type
from the 'TYPE' pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION]
card that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D6E
66
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
d.
Use the above functions to create 6-node linear triangular prisms and hence select the C3D_ type
from the 'TYPE' and E from the 'optional3' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D6H
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
d.
Use the above functions to create 6-node linear triangular prisms and hence select the C3D_ type
from the 'TYPE' and H from the 'optional2' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
67
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D6T
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
d.
Use the above functions to create 6-node linear triangular prisms and hence select the C3D_ type
from the 'TYPE' and T from the 'optional3' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
d.
Use the above functions to create 8-node linear bricks and hence select the C3D_ type from the
'TYPE' pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card that
exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
68
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=C3D8E
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8H
69
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8HT
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
d.
Use the above functions to create 8-node linear bricks and hence select the C3D_ type from the
'TYPE', H from the 'optional2' and T from 'optional3' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
70
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D8I
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
d.
Use the above functions to create 8-node linear bricks and hence select the C3D_ type from the
'TYPE' and I from the 'optional1' pull down menus respectively (SOLID SECTION&ELEMENT
TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8IH
71
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8R
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
72
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=C3D8RH
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8RHT
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
73
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8RT
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=C3D8T
74
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=CAX3
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CAX_ type from
the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
75
ANSA v13.x
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX3H
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CAX_ type from
the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
76
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX3T
The most basic functions to create 1st order triangular (3-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with TRIA or MIXED button, if unmeshed macros
exist in the current file.
b. Use MESH>ELEMENTs>NEW>NEW by selecting 3 nodes. The same function is placed in
DECK>ABAQUS>ELEMENTs>SHELL>NEW as well.
c. Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CAX_ type from
the 'TYPE' and T from the 'optional3' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the 'TYPE' pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
77
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4H
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
78
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX4HT
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the TYPE, H from the 'optional2' and T from the 'optional3' pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4I
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the 'TYPE' and I from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
79
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4IH
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the 1st, I from the 'optional1' and H from the 'optional2'TYPE pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
80
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX4R
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the 'TYPE' and R from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4RH
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the 1st, R from the 'optional1' and H from the 'optional2'TYPE pull down menus
respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in
PR.LIST).
BETA CAE Systems S.A.
81
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4RHT
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CAX_ type
from the TYPE, R from the 'optional1', H from the 'optional2' and T from the 'optional3' pull
down menus respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card
located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
82
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX4RT
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX4T
83
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX6
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CAX_ type from
the TYPE pull down menu of SHELL SECTION & ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CAX6H
84
Created by
ANSA v13.x
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CAX_ type from
the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX6M
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CAX_ type from
the 'TYPE' and M from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CAX6MH
85
Created by
ANSA v13.x
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CAX_ type from
the 1st, M from the 'optional1' and H from the 'optional2'TYPE pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX6MHT
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CAX_ type from
the 'TYPE', M from the 'optional1', H from the 'optional2' and T from the 'optional3' pull down
menus respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located
in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
86
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX6MT
The most basic functions to create 2nd order triangular (6-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with TRIA or MIXED button and '2nd ORD.' flag
active, if unmeshed macros exist in the current file.
b. Use DECK>ABAQUS>ELEMENTs>SHELL>NEW to create Trias by selecting 3 nodes in
combination with DECK > ABAQUS > ELEMENTs > Change Order to transit them to
2nd order (6-node).
Use the above functions to create triangular (6-node) shells and hence select the CAX_ type from
the 'TYPE', M from the 'optional1' and T from the 'optional3' pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CAX8
87
Created by
ANSA v13.x
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the TYPE pull down menu (SHELL SECTION & ELEMENT TYPE
[SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX8H
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CAX8HT
88
Created by
ANSA v13.x
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with QUAD or MIXED button and '2nd ORD.' flag
active, if unmeshed macros exist in the current file.
b. Use DECK>ABAQUS>ELEMENTs>SHELL>NEW or ON LINE EL by selecting 4 nodes
and line elements (BEAM, TRUSS) respectively in combination with DECK > ABAQUS
> ELEMENTs > Change Order to transit them to 2nd order (8-node).
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the TYPE, H from the 'optional2' and T from the 'optional3' pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX8R
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the 'TYPE' and R from the 'optional1' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
89
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX8RH
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the 1st, R from 'optional1' and H from the 'optional2'TYPE pull down menus respectively
(SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX8RHT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the TYPE, R from the 'optional1', H from the 'optional2' and T from the 'optional3' pull
down menus respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card
located in PR.LIST).
90
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CAX8RT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the 'TYPE', R from the 'optional1' and T from the 'optional3' pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
91
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CAX8T
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CAX_ type
from the 'TYPE' and T from the 'optional3' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CAX elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=COH3D6
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific COHESIVE
SECTION&ELEMENT TYPE [COHESIVE_SECTION] card. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
*ELEMENT, TYPE=COH3D8
92
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific COHESIVE
SECTION&ELEMENT TYPE [COHESIVE_SECTION] card. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
*ELEMENT, TYPE=CONN3D2
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific CONNECTOR
SECTION & ELEMENT TYPE [CONNECTOR_SECTION] card. See also GENERAL
REMARKS how to determine the name of ELSET parameter.
*ELEMENT, TYPE=CPE3
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CPE_ type from
the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
93
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=CPE3H
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CPE_ type from
the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CPE3T
94
Created by
ANSA v13.x
The most basic functions to create 1st order triangular (3-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with TRIA or MIXED button, if unmeshed macros
exist in the current file.
b. Use MESH>ELEMENTs>NEW>NEW by selecting 3 nodes. The same function is placed in
DECK>ABAQUS>ELEMENTs>SHELL>NEW as well.
c. Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CPE_ type from
the 'TYPE' and T from the 'optional3' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CPE4
95
Created by
ANSA v13.x
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE4H
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
96
ANSA v13.x
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE4HT
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CPE4I
97
Created by
ANSA v13.x
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the 'TYPE' and I from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE4IH
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the 1st, I from the 'optional1' and H from the 'optional2'TYPE pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
98
ANSA v13.x
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE4R
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the 'TYPE' and R from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=CPE4RH
99
Created by
ANSA v13.x
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the 1st, R from the 'optional1' and H from the 'optional2'TYPE pull down menus
respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in
PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE4RHT
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPE_ type
from the TYPE, R from the 'optional1', H from the 'optional2' and T from the 'optional3' pull
down menus respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card
located in PR.LIST).
100
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE4RT
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
101
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPE4T
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE6
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPE_ type from
the TYPE pull down menu of SHELL SECTION & ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
102
ANSA v13.x
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE6H
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPE_ type from
the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE6M
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPE_ type from
the 'TYPE' and M from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
103
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE6MH
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPE_ type from
the 1st, M from the 'optional1' and H from the 'optional2'TYPE pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE6MHT
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPE_ type from
the TYPE, M from the 'optional1', H from the 'optional2' and T from the 'optional3' pull down
menus respectively (SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located
in PR.LIST).
BETA CAE Systems S.A.
104
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE6MT
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPE_ type from
the TYPE, M from the 'optional1' and T from the 'optional3' pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
105
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPE8
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the TYPE pull down menu (SHELL SECTION & ELEMENT TYPE
[SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE8H
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the 'TYPE' and H from the 'optional2' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
106
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPE8HT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the 'TYPE', H from the 'optional2' and T from the 'optional3' pull down menus respectively
(SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE8R
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the 'TYPE' and R from the 'optional1' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
107
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPE8RH
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the 1st, R from 'optional1' and H from the 'optional2'TYPE pull down menus respectively
(SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE8RHT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the TYPE, R from 'optional1', H from the 'optional2' and T from the 'optional3' pull down
menus respectively (SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card located
in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
108
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=CPE8RT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the TYPE, R from 'optional1' and T from the 'optional3' pull down menus respectively
(SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPE8T
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPE_ type
from the TYPE and T from the 'optional3' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
109
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPE elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS3
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CPS_ type from
the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
110
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPS3T
The most basic functions to create 1st order triangular (3-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with TRIA or MIXED button, if unmeshed macros
exist in the current file.
b. Use MESH>ELEMENTs>NEW>NEW by selecting 3 nodes. The same function is placed in
DECK>ABAQUS>ELEMENTs>SHELL>NEW as well.
c. Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the CPS_ type from
the TYPE and T from 'optional2' pull down menus of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS4
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPS_ type
from the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
BETA CAE Systems S.A.
111
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS4I
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPS_ type
from the 'TYPE' and I from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
112
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPS4R
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPS_ type
from the 'TYPE' and R from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS4RT
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPS_ type
from the 'TYPE', R from the 'optional1' and T from 'optional2' pull down menus respectively
(SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
113
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS4T
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the CPS_ type
from the 'TYPE' and T from 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
114
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPS6
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPS_ type from
the TYPE pull down menu of SHELL SECTION & ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS6M
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPS_ type from
the 'TYPE' and M from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
115
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=CPS6MT
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the CPS_ type from
the 'TYPE, M from the 'optional1' and T from 'optional2' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS8
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPS_ type
from the TYPE pull down menu (SHELL SECTION & ELEMENT TYPE
[SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
116
ANSA v13.x
Created by
*ELEMENT, TYPE=CPS8R
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPS_ type from
the 'TYPE' and R from the 'optional1' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS8RT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPS_ type
from the 'TYPE' R from the 'optional1' and T from 'optional2' pull down menus respectively
(SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
117
ANSA v13.x
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=CPS8T
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the CPS_ type
from the 'TYPE' and T from 'optional2' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of CPS elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=DASHPOT1
Created by
ELEMENTs>DASHPOT>ONE NODE by selecting one node, having defined Fixed Dir. TYPE
from the specific DASHPOT [DASHPOT_PROP] card located in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific DASHPOT
[DASHPOT_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
118
Keyword
ANSA v13.x
*ELEMENT, TYPE=DASHPOT2
Created by
Remarks
The ELSET parameter can be specified through the Name field of the specific DASHPOT
[DASHPOT_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Keyword
*ELEMENT, TYPE=DASHPOTA
Created by
Remarks
The ELSET parameter can be specified through the Name field of the specific DASHPOT
[DASHPOT_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Keyword
Created by
*ELEMENT, TYPE=DC1D2
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
119
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION [TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
*ELEMENT, TYPE=DC1D2E
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION [TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
*ELEMENT, TYPE=DC2D3
120
Created by
ANSA v13.x
The most basic functions to create 1st order triangular (3-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with TRIA or MIXED button, if unmeshed macros exist
in the current file.
b. Use MESH>ELEMENTs>NEW>NEW by selecting 3 nodes. The same function is placed in
DECK>ABAQUS>ELEMENTs>SHELL>NEW as well.
c. Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (3node) and SURF (3-node) element types to SHELLs.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the DC2D_ type from
the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through
a shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=DC2D3E
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from
the pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the DC2D_ type from
the TYPE and E from 'optional1' pull down menus of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
121
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=DC2D4
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the DC2D_ type
from the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=DC2D4E
122
Created by
ANSA v13.x
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=DC2D6
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the DC2D_ type from
the TYPE pull down menu of SHELL SECTION & ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
123
ANSA v13.x
The properties of DC2D elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=DC2D6E
The most basic functions to create 2nd order triangular (6-node) shell elements:
a. Any algorithm of MESH>SHELL MESH group (FREE, BEST, SPOT-ME, GRADUAL,
MAP, ADV.FR, CFD) associated with TRIA or MIXED button and '2nd ORD.' flag
active, if unmeshed macros exist in the current file.
b. Use DECK>ABAQUS>ELEMENTs>SHELL>NEW to create Trias by selecting 3 nodes in
combination with DECK > ABAQUS > ELEMENTs > Change Order to transit them to
2nd order (6-node).
Use the above functions to create triangular (6-node) shells and hence select the DC2D_ type from
the 'TYPE' and E from the 'optional1' pull down menus respectively (SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through
a shell section inside ANSA.
Keyword
*ELEMENT, TYPE=DC2D8
124
Created by
ANSA v13.x
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the DC2D_ type
from the TYPE pull down menu (SHELL SECTION & ELEMENT TYPE
[SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
Created by
*ELEMENT, TYPE=DC2D8E
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the DC2D_ type
from the 'TYPE' and E from the 'optional1' pull down menus respectively (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DC2D elements are output in a solid section regardless they are defined through a
shell section inside ANSA.
Keyword
*ELEMENT, TYPE=DC3D10
125
Created by
ANSA v13.x
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the DC3D_ type from
the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D10E
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD to create TETRAs.
b.
Use the above functions to create 10-node quadratic tetras and hence select the DC3D_ type from
the 'TYPE' and E from the 'optional1' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D15
126
Created by
ANSA v13.x
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order triangular
shells.
d.
Use the above functions to create 15-node quadratic triangular prisms and hence select the DC3D_
type from the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE
[SOLID_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D15E
MESH menu: Define a volume from 2nd order shell elements (only Trias) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order triangular
shells.
d.
Use the above functions to create 15-node quadratic triangular prisms and hence select the DC3D_
type from the 'TYPE' and E from the 'optional1' pull down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
127
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=DC3D20
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the DC3D_ type from
the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D20E
b.
MESH menu: Use VOLUMEs>MAP with master area that contains 2nd order quad shells.
c.
Use the above functions to create 20-node quadratic bricks and hence select the DC3D_ type from
the 'TYPE' and E from the 'optional1' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
128
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=DC3D4
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
b.
Use the above functions to create 4-node linear tetras and hence select the DC3D_ type from the
TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exist in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D4E
MESH menu: Define a volume from 1st order shell elements (only Quads, only Trias, Mixed)
by using VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA FEM or TETRA CFD or TETRA + LAYERS or HEXA INTERIOR to
create TETRAs.
b.
Use the above functions to create 4-node linear tetras and hence select the DC3D_ type from the
'TYPE' and E from the 'optional1' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D6
129
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
d.
Use the above functions to create 6-node linear triangular prisms and hence select the DC3D_ type
from the TYPE pull down menu of SOLID SECTION&ELEMENT TYPE
[SOLID_SECTION] card that exist in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D6E
MESH menu: Define a volume from 1st order shell elements (only Trias, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create PENTAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains tria shells.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
130
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=DC3D8
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
d.
Use the above functions to create 8-node linear bricks and hence select the DC3D_ type from the
TYPE pull down menu of SOLID SECTION&ELEMENT TYPE [SOLID_SECTION] card
that exist in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DC3D8E
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID
131
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=DCC1D2
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
d.
Use any of the above functions to create truss elements and hence select the DCC1D2 from the
TYPE pull down menu of SOLID SECTION [TRUSS_PROP] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION [TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
*ELEMENT, TYPE=DCC1D2D
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
132
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION [TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
*ELEMENT, TYPE=DCC2D4
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the DCC2D4 type
from the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DCC2D4 elements are output in a solid section regardless they are defined
through a shell section inside ANSA.
133
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=DCC2D4D
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
The properties of DCC2D4 elements are output in a solid section regardless they are defined
through a shell section inside ANSA.
Keyword
*ELEMENT, TYPE=DCC3D8
134
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DCC3D8D
135
Created by
ANSA v13.x
MESH menu: Define a volume from 1st order shell elements (only Quads, Mixed) by using
VOLUMEs>DEFINE or VOLUMEs>INFO>DETECT functions and then
MESHV>TETRA + LAYERS or HEXA INTERIOR to create HEXAs.
b.
c.
MESH menu: Use VOLUMEs>MAP with master area that contains quad shells.
d.
Use the above functions to create 8-node linear bricks and hence select the DCC3D_ type from the
'TYPE' and D from the 'optional1' pulls down menus respectively (SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID
SECTION&ELEMENT TYPE [SOLID_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DCOUP3D
CONSTRAINTs>KINEM>NODES
2.
CONSTRAINTs>KINEM>SET
3.
CONSTRAINTs>DISTR>NODES
4.
CONSTRAINTs>DISTR>SET
Remarks
Keyword
The ELSET parameter is automatically specified with the standard name: DCOUP3D_(eid). Take
control of the ELSET name by changing its eid trough the corresponding field of *COUPLING
[DISTIBUTING_COUPLING/DCOUP3D] card.
*ELEMENT, TYPE=DGAP
136
Created by
ANSA v13.x
ELEMENTs>GAP.
b.
c.
Use AUXILIARIES>BOLT function to create GAPs choosing the relative option from the
pull down menus of Head or Nut section.
d.
Use any of the above functions to create gap elements and hence select the DGAP type from the
TYPE pull down menu of *GAP [GAP_PROP] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific PGAP card. See
also GENERAL REMARKS how to determine the name of ELSET parameter.
*ELEMENT, TYPE=DS3
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d.
Use AUXILIARIES>BOLT function to create SHELLs choosing the 'TRIAS' option from the
pull down menus of 'Head' or 'Nut' section.
Use the above functions to create triangular (3-node) shells and hence select the DS_ type from the
TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DS4
137
Created by
ANSA v13.x
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the DS_ type from
the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION]
card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DS6
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the DS_ type from the
TYPE pull down menu of SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=DS8
138
Created by
ANSA v13.x
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the DS_ type from
the TYPE pull down menu (SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card
located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=GAPCYL
ELEMENTs>GAP.
b.
c.
Use AUXILIARIES>BOLT function to create GAPs choosing the relative option from the
pull down menus of Head or Nut section.
d.
Use any of the above functions to create gap elements and hence select the GAPCYL type from the
TYPE pull down menu of *GAP [GAP_PROP] card that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific PGAP card. See
also GENERAL REMARKS how to determine the name of ELSET parameter.
*ELEMENT, TYPE=GAPSPHER
139
Created by
ANSA v13.x
ELEMENTs>GAP.
b.
c.
Use AUXILIARIES>BOLT function to create GAPs choosing the relative option from the
pull down menus of Head or Nut section.
d.
Use any of the above functions to create gap elements and hence select the GAPSPHER type from
the TYPE pull down menu of *GAP [GAP_PROP] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific PGAP card. See
also GENERAL REMARKS how to determine the name of ELSET parameter.
*ELEMENT, TYPE=GAPUNI
ELEMENTs>GAP.
b.
c.
Use AUXILIARIES>BOLT function to create GAPs choosing the relative option from the
pull down menus of Head or Nut section.
d.
Use any of the above functions to create gap elements and hence select the GAPUNI type from the
TYPE pull down menu of PGAP card that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific *GAP
[GAP_PROP] card. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
*ELEMENT, TYPE=GAPUNIT
140
Created by
ANSA v13.x
ELEMENTs>GAP.
b.
c.
Use AUXILIARIES>BOLT function to create GAPs choosing the relative option from the
pull down menus of Head or Nut section.
d.
Use any of the above functions to create gap elements and hence select the GAPUNIT type from the
TYPE pull down menu of *GAP [GAP_PROP] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific PGAP card. See
also GENERAL REMARKS how to determine the name of ELSET parameter.
*ELEMENT, TYPE=GK3D2
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
Keyword
*ELEMENT, TYPE=GK3D2N
141
Created by
ANSA v13.x
b.
Use the above functions to create three-dimensional (2-node) gaskets and hence select the N from
the 'optional1' TYPE pull down menu (GASKET SECTION [GASKET_SECTION] card
located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
Keyword
Created by
*ELEMENT, TYPE=GK3D4L
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
Keyword
*ELEMENT, TYPE=GK3D4LN
142
Created by
ANSA v13.x
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing quad shells (1st
and 2nd order), R3D (4-node), SURF (4-node) and 2nd order GASKET (GK3D6L) element
types to GASKETs.
Use the above functions to create three-dimensional line (4-node) gaskets and hence select the N
from the 'optional1' TYPE pull down menu (GASKET SECTION [GASKET_SECTION] card
located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
Keyword
Created by
*ELEMENT, TYPE=GK3D6L
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
Keyword
*ELEMENT, TYPE=GK3D6LN
143
Created by
ANSA v13.x
b.
c.
Use the above functions to create three-dimensional line (6-node) gaskets and hence select the N
from the 'optional1' TYPE pull down menu (GASKET SECTION [GASKET_SECTION] card
located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
Keyword
Created by
*ELEMENT, TYPE=GK3D6
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
Keyword
*ELEMENT, TYPE=GK3D6N
144
Created by
ANSA v13.x
b.
c.
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
Keyword
Created by
*ELEMENT, TYPE=GK3D8
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
145
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=GK3D8N
b.
c.
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
Keyword
Created by
*ELEMENT, TYPE=GK3D12M
146
ANSA v13.x
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
Keyword
Created by
*ELEMENT, TYPE=GK3D12MN
b.
c.
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
147
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=GK3D18
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
Keyword
Created by
*ELEMENT, TYPE=GK3D18N
b.
c.
Remarks
The ELSET parameter can be specified through the Name field of the specific GASKET
SECTION [GASKET_SECTION]. See also GENERAL REMARKS how to determine the name of
148
ANSA v13.x
ELSET parameter.
Use ELEMENTs>GASKET>STACK DIRECTION>INVERT or ROTATE to invert the orientation
of the selected link gaskets if desired. Use ELEMENTs>GASKET>ORIENT BY to assign the same
orientation in a sequence of connected gaskets.
SOLID ELEMENT NUMBERING parameter is supported only during input. ANSA reorders nodes
so as to define as 1st face the face specified in parameter.
Keyword
Created by
Remarks
Keyword
Created by
*ELEMENT, TYPE=HEATCAP
ELEMENTs>HEATCAP
The ELSET parameter can be specified through the Name field of the specific *HEATCAP
[HEATCAP_PROP] (Press F2 key in PID field). See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=JOINTC
ELEMENTs>JOINTC.
Using ELEMENTs>UTIL>Change Type>1-d Entities function to switch existing 1D-element types
to JOINTCs.
Using AUXILIARIES>BOLT function to create JOINTCs choosing the relative option from the
pull down menu of Body section.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific JOINT
[JOINT_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
*ELEMENT, TYPE=M3D3
149
Created by
ANSA v13.x
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d. Use AUXILIARIES>BOLT function to create SHELLs choosing the TRIAS option from
the pull down menus of Head or Nut section.
Use the above functions to create triangular (3-node) shells and hence select the M3D_ type from
the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE
[MEMBRANE_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [MEMBRANE_SECTION]. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
*ELEMENT, TYPE=M3D4
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the M3D_ type
from the TYPE pull down menu of SHELL SECTION&ELEMENT TYPE
[MEMBRANE_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [MEMBRANE_SECTION]. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
150
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=M3D4R
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the M3D_ type
from the 'TYPE' and R from the 'optional1' pull down menu of SHELL SECTION&ELEMENT
TYPE [MEMBRANE_SECTION] card that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [MEMBRANE_SECTION]. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
*ELEMENT, TYPE=M3D6
151
Created by
ANSA v13.x
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the M3D_ type from
the TYPE pull down menu of SHELL SECTION & ELEMENT TYPE
[MEMBRANE_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [MEMBRANE_SECTION]. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
*ELEMENT, TYPE=M3D8
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the M3D_ type
from the TYPE pull down menu (SHELL SECTION & ELEMENT TYPE
[MEMBRANE_SECTION] card located in PR.LIST).
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [MEMBRANE_SECTION]. See also GENERAL REMARKS
how to determine the name of ELSET parameter.
*ELEMENT, TYPE=M3D8R
152
Created by
ANSA v13.x
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the M3D_ type
from the 'TYPE' and R from the 'optional1' pull down menu (SHELL SECTION & ELEMENT
TYPE [MEMBRANE_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific *ELEMENT
MASS&*ELEMENT ROTARY [MASS]. See also GENERAL REMARKS how to determine the
name of ELSET parameter.
*ELEMENT, TYPE=MASS
ELEMENTs>MASS>Node or Set.
ELEMENTs>UTIL>Mass Balance
Remarks
The ELSET parameter can be specified through the Name field of the specific *ELEMENT
MASS&*ELEMENT ROTARY [MASS]. See also GENERAL REMARKS how to determine the
name of ELSET parameter.
If PER ELEMENT or PER ELEMENT AREA TYPE (*ELEMENT MASS&*ELEMENT
ROTARY [MASS] card) is selected in case that ELEMENTs>MASS>Set is performed, the mass
points are written out in a *NONSTRUCTURAL MASS keyword.
Keyword
*ELEMENT, TYPE=PIPE31
153
Created by
ANSA v13.x
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of Head, Body or Nut section.
d.
Use any of the above functions to create beams and hence select the PIPE31 type from the TYPE
pull down menu of BEAM SECTION&ELEMENT TYPE [BEAM_SECTION] card that exists
in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=PIPE31H
ELEMENTs>BEAM.
b.
c.
Use AUXILIARIES>BOLT function to create BEAMs choosing the relative option from the
pull down menus of Head, Body or Nut section.
Remarks
The ELSET parameter can be specified through the Name field of the specific BEAM
SECTION&ELEMENT TYPE [BEAM_SECTION]. See also GENERAL REMARKS how to
154
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=R3D3
Remarks
Keyword
Created by
*ELEMENT, TYPE=R3D4
Remarks
Keyword
Created by
*ELEMENT, TYPE=ROTARYI
1.
ELEMENTs>MASS>Node.
2.
Use one of the above functions to create mass points and type a value at least in one of the I11,
I22, I33, I12, I13 and I23 fields to specify ROTARYI elements.
Remarks
The ELSET parameter can be specified through the Name field of the specific *ELEMENT
MASS&*ELEMENT ROTARY [MASS]. See also GENERAL REMARKS how to determine the
name of ELSET parameter.
155
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=S3R
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d.
Use AUXILIARIES>BOLT function to create SHELLs choosing the TRIAS option from the
pull down menus of Head or Nut section.
Use the above functions to create triangular (3-node) shells and hence select the S_ type from the
TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card
that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
S3 element type is not supported during output because this is identical to element S3R (it can be
only read during input).
Keyword
*ELEMENT, TYPE=S3RS
156
Created by
ANSA v13.x
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d.
Use AUXILIARIES>BOLT function to create SHELLs choosing the TRIAS option from the
pull down menus of Head or Nut section.
Use the above functions to create triangular (3-node) shells and hence select the S_ type from the
'TYPE' and RS from the 'optional1' pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S3RT
157
Created by
ANSA v13.x
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d.
Use AUXILIARIES>BOLT function to create SHELLs choosing the TRIAS option from the
pull down menus of Head or Nut section.
Use the above functions to create triangular (3-node) shells and hence select the S_ type from the
'TYPE, R from the 'optional1' and T from 'optional2' pull down menu of SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S3T
The most basic functions to create 1st order triangular (3-node) shell elements:
a.
b.
c.
d.
Use AUXILIARIES>BOLT function to create SHELLs choosing the TRIAS option from the
pull down menus of Head or Nut section.
Use the above functions to create triangular (3-node) shells and hence select the S_ type from the
TYPE and T from 'optional2'pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
S3 element type is not supported because this is identical to element S3R.
158
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=S4
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the S_ type from the
TYPE pull down menu of SHELL SECTION&ELEMENT TYPE [SHELL_SECTION] card
that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S4R
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the S_ type from the
'TYPE' and R from the 'optional1' pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
159
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=S4R5
b.
c.
Use the above functions to create quadrilateral (4-node) shells and hence select the S_ type from the
'TYPE' and R5 from the 'optional1' pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S4RS
b.
c.
Use the above functions to create quadrilateral (4-node) shells and hence select the S_ type from the
'TYPE' and RS from the 'optional1' pull down menu of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
160
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S4RT
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the S_ type from the
'TYPE', R from the 'optional1' and T from the 'optional2'pull down menus of SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S4T
b.
c.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing R3D (4node), SURF (4-node), GASKET and GASKET (2nd order) element types to SHELLs.
Use the above functions to create quadrilateral (4-node) shells and hence select the S_ type from the
'TYPE' and T from the 'optional2' pull down menus of SHELL SECTION&ELEMENT TYPE
[SHELL_SECTION] card that exists in PR.LIST.
161
Remarks
Keyword
Created by
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S8R
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the S_ type from the
TYPE pull down menu (SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card
located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=S8R5
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the S_ type from the
'TYPE' and R3 from the 'optional1' pull down menu (SHELL SECTION & ELEMENT TYPE
[SHELL_SECTION] card located in PR.LIST).
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
162
ANSA v13.x
Keyword
Created by
*ELEMENT, TYPE=S8RT
The most basic functions to create 2nd order quadrilateral (8-node) shell elements:
a.
b.
Use the above functions to create quadrilateral (8-node) shells and hence select the S_ type from the
'TYPE', R from the 'optional1' and T from the 'optional2' pull down menus (SHELL SECTION &
ELEMENT TYPE [SHELL_SECTION] card located in PR.LIST).
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
*ELEMENT, TYPE=SC6R
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [CONTINUUM_SHELL_SECTION]. See also GENERAL
REMARKS how to determine the name of ELSET parameter.
Use ELEMENTs>C.SHELL>ORIENT BY to assign the same orientation in a sequence of
connected continuum shells.
163
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=SC6RT
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [CONTINUUM_SHELL_SECTION]. See also GENERAL
REMARKS how to determine the name of ELSET parameter.
Use ELEMENTs>C.SHELL>ORIENT BY to assign the same orientation in a sequence of
connected continuum shells.
Keyword
Created by
*ELEMENT, TYPE=SC8R
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [CONTINUUM_SHELL_SECTION]. See also GENERAL
REMARKS how to determine the name of ELSET parameter.
Use ELEMENTs>C.SHELL>ORIENT BY to assign the same orientation in a sequence of
connected continuum shells.
Keyword
Created by
*ELEMENT, TYPE=SC8RT
164
ANSA v13.x
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [CONTINUUM_SHELL_SECTION]. See also GENERAL
REMARKS how to determine the name of ELSET parameter.
Use ELEMENTs>C.SHELL>ORIENT BY to assign the same orientation in a sequence of
connected continuum shells.
Keyword
Created by
*ELEMENT, TYPE=SFM3D3
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific *SURFACE
SECTION [SURFACE_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
*ELEMENT, TYPE=SFM3D4
Remarks
The ELSET parameter can be specified through the Name field of the specific *SURFACE
SECTION [SURFACE_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
165
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=SFM3D4R
b.
Use ELEMENTs>UTIL>Change Type>2-d Entities function to switch existing 1st and 2nd
order quad shells (4-node, 8-node), R3D (4-node) and 1st and 2nd line gaskets (GK3D4L,
GK3D6L) element types to SURF (4-node).
c.
Use the above functions to create quadrilateral (4-node) surface elements and hence select the R
from the 'optional1' TYPE pull down menu (*SURFACE SECTION [SURFACE_SECTION]
card located in PR.LIST).
Remarks
Keyword
The ELSET parameter can be specified through the Name field of the specific *SURFACE
SECTION [SURFACE_SECTION]. See also GENERAL REMARKS how to determine the name
of ELSET parameter.
*ELEMENT, TYPE=SPRING1
Created by
ELEMENTs>SPRING>ONE NODE by selecting one node, having defined Fixed Dir. TYPE
from the specific *SPRING [SPRING_PROP] card located in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific *SPRING
[SPRING_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Keyword
*ELEMENT, TYPE=SPRING2
Created by
ELEMENTs>SPRING>TWO NODES by selecting two nodes, having defined Fixed Dir. TYPE
from the specific *SPRING [SPRING_PROP] card located in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific *SPRING
[SPRING_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
166
Keyword
ANSA v13.x
*ELEMENT, TYPE=SPRINGA
Created by
ELEMENTs>SPRING>TWO NODES by selecting two nodes, having defined Axial. TYPE from
the specific *SPRING [SPRING_PROP] card located in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific *SPRING
[SPRING_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Keyword
*ELEMENT, TYPE=STRI3
Created by
This is supported only during input. ANSA converts it to element S3R assuming that these two
types are similar.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
Keyword
Created by
*ELEMENT, TYPE=STRI65
The most basic functions to create 2nd order triangular (6-node) shell elements:
a.
b.
Use the above functions to create triangular (6-node) shells and hence select the S_ type from the
TYPE pull down menu of SHELL SECTION & ELEMENT TYPE [SHELL_SECTION] card
that exists in PR.LIST.
Remarks
The ELSET parameter can be specified through the Name field of the specific SHELL
SECTION&ELEMENT TYPE [SHELL_SECTION]. See also GENERAL REMARKS how to
determine the name of ELSET parameter.
167
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=T3D2
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
d.
Use any of the above functions to create truss elements and hence select the T3D2 from the TYPE
pull down menu of SOLID SECTION [TRUSS_PROP] card that exists in PR.LIST.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID SECTION
[TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
*ELEMENT, TYPE=T3D2E
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID SECTION
[TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
168
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=T3D2H
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
Remarks
Keyword
Created by
The ELSET parameter can be specified through the Name field of the specific SOLID SECTION
[TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
*ELEMENT, TYPE=T3D2T
ELEMENTs>TRUSS.
b.
c.
Use AUXILIARIES>BOLT function to create TRUSS elements choosing the relative option
from the pull down menus of Head, Body or Nut section.
Remarks
The ELSET parameter can be specified through the Name field of the specific SOLID SECTION
[TRUSS_PROP]. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
169
Keyword
Created by
ANSA v13.x
*ELEMENT, TYPE=Z????
1. ELEMENTs>ZELEMENT>NEW
2. Automatically by using AUXILIARIES>SUBSTR>LIST>NEW. When finishing with
substructure definition the Z elements are generated during output (see also tutorial 11 of docs
folder included in distribution package for more details concerning the substructure definitions).
Remarks
Keyword
*EL FILE
Created by
Remarks
Press the ? key into ELSET field to define the element set for which this output request is being
made. The user is able to select more than one sets at once in order to define more than one output
requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Press the Output Variables button and activate any variable to be written to the results file for the
specified element set or for all elements existing in the entire model. Alternatively, type the
identifying keys for the element variables, separated with commas, through the corresponding
(Identifying Keys) field of ELEMENT VARIABLES window. Do the same in Section Points
field to give a list of the section points to be printed.
170
Keyword
ANSA v13.x
*EL PRINT
Created by
Remarks
Press the ? key into ELSET field to define the element set for which this output request is being
made. The user is able to select more than one sets at once in order to define more than one output
requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Press the Output Variables button and activate any variable to be printed to a table for the
specified element set or for all elements existing in the entire model. Alternatively, type the
identifying keys for the element variables, separated with commas, through the corresponding
(Identifying Keys) field of ELEMENT VARIABLES window. Do the same in Section Points
field to give a list of the section points to be printed.
Keyword
*ELEMENT OUTPUT
Created by
Remarks
Press the ? key into ELSET field to define the element set for which this output request is being
made. The user is able to select more than one sets at once in order to define more than one output
requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Press the Output Variables button and activate any variable to be written to the output database
for the specified element set or for all elements existing in the entire model. Alternatively, type the
identifying keys for the element variables, separated with commas, through the corresponding
(Identifying Keys) field of ELEMENT VARIABLES window. Do the same in Section Points
field to give a list of the section points to be written to the output database.
Keyword
Created by
*ELSET
171
Remarks
ANSA v13.x
The ELSET parameter can be specified through the Name field of the specific SET [SET]card.
See also GENERAL REMARKS how to determine the name of ELSET parameter.
The set can contain any element type except the MASS and ROTARYI elements. In these elements
the *ELSET option makes no sense.
Switch AUXILIARY option to NO and DEFINED to YES so as the specific *ELSET option to be
exported (SET [SET] card).
Keyword
*EMBEDDED ELEMENT
Created by
Using AUXILIARIES>EMBEDDED>NEW
Remarks
The embedded and host elements can be defined through element sets (*ELSETs) by pressing the '?'
key in EMBEDDED ELSET and HOST ELSET fields of *EMBEDDED ELEMENT card
respectively. The names of embedded elements set and HOST ELSET parameter can be specified
through the Name field of the corresponding SET [SET]cards. See also GENERAL REMARKS
how to determine the names of embedded and host elements sets.
If embedded elements are defined directly with their ids in *EMBEDDED ELEMENT then they are
placed in a set with name Anonymous set of embedded elements during input. Thus, if output
again the element label will be written instead of their ids.
Keyword
Created by
Remarks
Keyword
Created by
*END STEP
172
Remarks
Keyword
ANSA v13.x
*ENERGY FILE
Created by
Remarks
Press the ? key into ELSET field to define the element set for which this output request is being
made. The user is able to select more than one sets at once in order to define more than one output
requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Keyword
*ENERGY OUTPUT
Created by
Remarks
Press the ? key into ELSET field to define the element set for which this output request is being
made. The user is able to select more than one sets at once in order to define more than one output
requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Press the Output Variables button and activate any variable to be written to the output database for
the specified element set or for all elements existing in the entire model. Alternatively, type the
identifying keys for the energy variables, separated with commas, through the corresponding
(Identifying Keys) field of ENERGY VARIABLES window.
Switch ANALYSIS to *DYNAMIC, EXPLICIT and then PER ELEMENT SET to PER SET and
PER SECTION to PER SECTION in order to define the relative parameters. The parameters are
written out only if 'Output Format' is set to 6.8 (ABAQUS Output Parameters window).
Keyword
Created by
*ENERGY PRINT
173
Remarks
Keyword
Created by
ANSA v13.x
Press the ? key into ELSET field to define the element set for which this output request is being
made. The user is able to select more than one sets at once in order to define more than one output
requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
*EOS
Remarks
Keyword
*EOS SHEAR
Created by
Remarks
The temperature values may be specified only if DEP parameter is set to YES. See also section
'Defining non-linear material properties (as a function of temperature) in tabular forms.' of
GENERAL REMARKS for more details. DEPENDENCIES parameter is supported if the data
table defined in above manner contains other columns after the 'Temperature' one. The number of
these columns (var(i)) determines the number of DEPEDENCIES parameter.
Keyword
Created by
*EQUATION
CONSTRAINTs>EQUATION>MANY NODES.
CONSTRAINTs>EQUATION>TWO NODES.
Remarks
174
Keyword
Created by
ANSA v13.x
*EXPANSION
Remarks
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE field to define the corresponding
table at each TYPE that is used). DEPENDENCIES parameter is supported if the data table
defined in above manner contains other columns after the 'Temperature' one. The number of these
columns (var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *EXPANSION option to be written to the output file (.inp).
175
ANSA v13.x
Keyword
*FAIL STRAIN
Created by
Remarks
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE field to define the strain-based
failure criteria - temperature table). DEPENDENCIES parameter is supported if the data table
defined in above manner contains other columns after the 'Temperature' one. The number of these
columns (var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *FAIL STRAIN option to be written to the output file (.inp).
Keyword
*FAIL STRESS
Created by
Remarks
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE field to define the stress-based
failure criteria - temperature table). DEPENDENCIES parameter is supported if the data table
defined in above manner contains other columns after the 'Temperature' one. The number of these
columns (var(i)) determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *FAIL STRESS option to be written to the output file (.inp).
Keyword
Created by
*FASTENER
176
ANSA v13.x
and
spotweld
lines
through
TOPO>WELD
Remarks
177
ANSA v13.x
generates a single surface with all layers regardless the flag is active or not.
Type '? key in 'FASTENER PID:' field to create or select an existing *FASTENER PROPERTY
and consequently to determine the name of PROPERTY parameter.
Specify a value in 'Influence Radius' field in order to determine INFLUENCE RADIUS parameter
(the value is set to INFLUENCE R field of FASTENER card).
The vector of the projection direction can be specified through V1, V2 and V3 fields when
ADJUST is set to NO (*FASTENER [FASTENER] card).
Up to twelve surfaces can be connected for each fastener interaction (press the ? key in SURF1,
, SURF12 fields of *FASTENER [FASTENER] card to define the surfaces by selecting sets
of elements, facets of solids and edges of shells).
Press ? key in INTERACTION field, edit to the defined interaction and type a new name in
Name field to determine the INTERACTION NAME parameter. Do the same in PID field to
determine the PROPERTY parameter (*FASTENER [FASTENER] card). See also GENERAL
REMARKS how to determine the names of REFERENCE NODE SET, ELSET, INTERACTION
NAME, PROPERTY and ORIENTATION parameters.
The ATTACHMENT METHOD parameter is written out only if 'Output Format' menu is switched
to 6.8 (ABAQUS Output Parameters window).
Keyword
Created by
*FASTENER PROPERTY
MENUBAR>Windows>Properties>NEW>FASTENER.
Through PID field of FASTENER card (See also *FASTENER keyword).
Through FASTENER PID field of Connection Manager with FE Representation ABAQUS
FASTENER (See also *FASTENER keyword).
Remarks
The NAME parameter can be specified through the Name field of the specific FASTENER
PROPERTY [FASTENER_PROPERTY]card. See also GENERAL REMARKS how to determine
the name of NAME parameter.
Type 1 to 6 in DOF field to define the degrees of freedom that will be constrained.
The half of specified value in D column of connection manager is assigned as RADIUS in
*FASTENER PROPERTY card. If value of D column is zero and 'Use Thickness to Diameter Map'
flag is active the value of RADIUS parameter is calculated through thickness rule as described in
ANSA.defaults file.
Set DEFINED option to YES (located at the top of FASTENER PROPERTY
[FASTENER_PROPERTY] card) so as the specific *FASTENER PROPERTY option to be
written to the output file (.inp).
178
Keyword
ANSA v13.x
*FIELD
Created by
Remarks
See GENERAL REMARKS how to determine the node set names and the name of AMPLITUDE
parameter.
If Field flag into RESET region of STEP card (AUXILIARIES>STEP>NEW) is active, all of
*FIELD options in this step enquire OP=NEW parameter.
Up to 5 temperature points are supported.
Keyword
*FILE FORMAT
Created by
Using AUXILIARIES>STEP>*FILE FORMAT and switching at least one of the two parameters to
YES, ASCII or ZERO INCREMENT (the button is coloured to red to indicate that the current
keyword is defined).
Remarks
Keyword
*FILE OUTPUT
Created by
Remarks
This option is used only in Abaqus/Explicit analyses and so *DYNAMIC, EXPLICIT ANALYSIS
should be defined.
179
Keyword
Created by
ANSA v13.x
*FILM
LOADs>FILM>Element.
LOADs>FILM>Set.
Remarks
Switch film amplitude to Film Property and specify the name of film property table through
FILM PROPERTY field. See also GENERAL REMARKS how to determine the name of
AMPLITUDE and FILM AMPLITUDE parameters as well as the element set names and the names
of film property table.
For sets the option 'Output as: should be switched to Set in order to output *FILM keyword.
If film flag into RESET region of STEP card is active, all *FILM options in this step acquire
OP=NEW parameter.
Keyword
*FILM PROPERTY
Created by
Setting film amplitude to Film Property and pressing ? key in FILM PROPERTY field to
define the film coefficient as a function of temperature (*FILM [FILM] card). See also *FILM
keyword.
Remarks
Type any name in Name field of the specific DATA TABLE card to determine the NAME
parameter. See also GENERAL REMARKS how to determine the name of NAME parameter.
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
180
Keyword
Created by
Remarks
ANSA v13.x
*FILTER
2.
3.
4.
5.
Type any name in Name field of the specific *FILTER [FILTER] card to determine the NAME
parameter. See also GENERAL REMARKS how to determine the name of NAME parameter.
START CONDITION parameter is exported only if 'Output Format' menu is switched to 6.7 or 6.8
during output.
Keyword
Created by
Remarks
Press the ? key into ELSET field to define the element set for which this mass scaling definition is
being applied. The user is able to select more than one sets at once in order to define more than one
output requests quickly. See also GENERAL REMARKS how to determine the name of ELSET
parameter.
Select DYNAMIC, EXPLICIT ANALYSIS because *FIXED MASS SCALING can be used only
in an Abaqus/Explicit analysis.
Keyword
Created by
*FLUID BEHAVIOR
MENUBAR>Windows>Materials>NEW>FLUID BEHAVIOR.
181
ANSA v13.x
Remarks
Set DEFINED option to YES (located at the top of FLUID BEHAVIOR [FLUID BEHAVIOR]
card) so as the specific FLUID BEHAVIOR option to be written to the output file (.inp). In order to
avoid the above, activate the 'set default' option of an already existing FLUID BEHAVIOR in
MATDB. Then when creating a new FLUID BEHAVIOR, this will take the properties of the
FLUID BEHAVIOR in MATDB and the DEFINED=YES automatically.
The NAME parameter can be specified through the Name field of FLUID BEHAVIOR [FLUID
BEHAVIOR] card. See also GENERAL REMARKS how to determine the name of NAME
parameter.
Keyword
Created by
*FLUID CAVITY
AUXILIARIES>AIRBAG>*FLUID CAVITY>NEW.
Automatically by AUXILIARIES>AIRBAG>Enclose Cavity.
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output.
Up to 16 fluid behaviours can be specified if MIXTURE parameter is defined (switch 2 nd menu to
MIXTURE).
The NAME parameter can be specified through the Name field of FLUID CAVITY [FLUID
CAVITY] card. See also GENERAL REMARKS how to determine the name of NAME,
BEHAVIOR and SURFACE parameters. Node set name for REF NODE is supported only during
input.
Keyword
Created by
*FLUID EXCHANGE
AUXILIARIES>AIRBAG>*FLUID EXCHANGE>NEW.
Automatically by AUXILIARIES>AIRBAG>Enclose Cavity.
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output.
The NAME parameter can be specified through the Name field of *FLUID EXCHANGE
[FLUID EXCHANGE] card. See also GENERAL REMARKS how to determine the name of
182
ANSA v13.x
Keyword
Created by
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output. In addition, specify STEP field by selecting the id of a DYNAMIC,
EXPLICIT step so as to be written as history data.
See GENERAL REMARKS how to determine the name of AMPLITUDE parameter and fluid
exchange names.
Press '?' key in 'FLUID EXCHANGE' field to select the desired fluid exchanges that will be
activated from the list that opens and click INSERT button to declare the definition.
Keyword
Created by
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output.
The NAME parameter can be specified through the Name field of *FLUID EXCHANGE
PROPERTY [FLUID EXCHANGE PROPERTY] card. See also GENERAL REMARKS how to
determine the name of NAME parameter.
The pressure or temperature difference, average absolute pressure, average temperature and values
may be specified only if DEP option is set to YES. They are introduced in the last columns of the
table in the sequence as described in ABAQUS manual(Press the ? key in DATA TABLE field
to define the corresponding table according to the TYPE parameter). DEPENDENCIES parameter
is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
DEPEDENCIES parameter.
Keyword
*FLUID INFLATOR
183
ANSA v13.x
Created by
AUXILIARIES>AIRBAG>*FLUID INFLATOR>NEW.
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output.
The NAME parameter can be specified through the Name field of *FLUID INFLATOR [FLUID
INFLATOR] card. See also GENERAL REMARKS how to determine the name of NAME and
PROPERTY parameters.
Keyword
Created by
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output. In addition, specify STEP field by selecting the id of an DYNAMIC,
EXPLICIT step so as to be written as history data.
See GENERAL REMARKS how to determine the name of INFLATION TIME AMPLITUDE and
MASS FLOW AMPLITUDE parameters.
Press '?' key in 'FLUID INFLATOR' field to select the desired fluid inflators that will be activated
from the list that opens and click INSERT button to declare the definition.
Keyword
Created by
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output.
See GENERAL REMARKS how to determine the name of each specified BEHAVIOR parameter.
Up to 8 BEHAVIORs can be specified.
Set DEP option to YES to define the mass fraction or molar fraction as a function of inflation time.
(Press the ? key in DATA TABLE field to define the corresponding table).
184
Keyword
ANSA v13.x
Created by
Remarks
Due to the fact that it is valid only in an ABAQUS/Explicit analysis activate 'Abaqus Explicit
output' flag during output.
The NAME parameter can be specified through the Name field of *FLUID INFLATOR
PROPERTY [FLUID INFLATOR PROPERTY] card. See also GENERAL REMARKS how to
determine the name of NAME parameter.
Set DEP option to YES to define the respective components of each TYPE as a function of
inflation time. (Press the ? key in DATA TABLE field to define the corresponding table).
Keyword
*FREQUENCY
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *FREQUENCY option into the pull
down menu of ANALYSIS section.
Remarks
Keyword
*FRICTION
185
Created by
ANSA v13.x
2.
Set to YES the *FRICTION option and type ? key in FRICT_ID field to define a new
*FRICTION through *FRICT/HELP card (The same card appears when
AUXILIARIES>FRICTION>NEW is performed).
3.
Specify the parameters in the *FRICTION [FRICTION] card as needed, press OK and
double click on it to appear its ID in FRICT_ID field.
4.
Press
OK
in
SURFACE
INTERACTION/CONTACT
[SURFACE_INTERACTION] card to declare the definition.
PROPERTIES
Remarks
186
ANSA v13.x
Keyword
*GAP
Created by
MENUBAR>Windows>Properties>NEW>GAP.
Remarks
The ELSET parameter can be specified through the Name field of the specific PGAPcard. See
also GENERAL REMARKS how to determine the name of ELSET parameter.
Set DEFINED option to YES (located at the top of PGAP card) so as the specific *GAP option
to be written to the output file (.inp).
Keyword
Created by
*GAP CONDUCTANCE
2.
Set to YES the *GAP CONDUCTANCE option and type ? key in one of the K-P-T
TABLE or K-D-T TABLE fields to define gap conductance as a function of pressure
and temperature or clearance and temperature respectively.
3.
Specify the table in the DATA TABLE HELP card as needed, press OK and double click
on it to appear its ID in the corresponding field.
4.
Press
OK
in
SURFACE
INTERACTION/CONTACT
[SURFACE_INTERACTION] card to declare the definition.
Use MENUBAR>Windows>Properties>NEW>GAP
CONDUCTANCE option.
Remarks
and
set
to
YES
PROPERTIES
the
*GAP
The PRESSURE parameter is written out when K-P-T TABLE field is specified.
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
187
Keyword
Created by
ANSA v13.x
2.
Set to YES the *GAP HEAT GENERATION option and fill the N (n, fraction) and J (f,
weighting factor) fields as needed.
3.
Press
OK
in
SURFACE
INTERACTION/CONTACT
[SURFACE_INTERACTION] card to declare the definition.
PROPERTIES
Remarks
Keyword
Created by
*GAP RADIATION
2.
Set to YES the *GAP RADIATION option and fill the fields as needed.
3.
Press
OK
in
SURFACE
INTERACTION/CONTACT
[SURFACE_INTERACTION] card to declare the definition.
PROPERTIES
Remarks
Keyword
Press the ? key in F-D TABLE field to define the dependence of the view factor on gap
clearance in tabular form.
*GASKET BEHAVIOR
188
ANSA v13.x
Created by
MENUBAR>Windows>Materials>NEW>GASKET BEHAVIOR.
Remarks
Set DEFINED option to YES (located at the top of GASKET BEHAVIOR [GASKET
BEHAVIOR] card) so as the specific *GASKET BEHAVIOR option to be written to the output
file (.inp). In order to avoid the above activate either the 'set default' or 'set default for
prop=GASKET_SECTION' options of an already existing GASKET BEHAVIOR in MATDB.
Then when creating a new GASKET BEHAVIOR or a GASKET SECTION respectively, this will
take the properties of the GASKET BEHAVIOR in MATDB and the DEFINED=YES
automatically.
The NAME parameter can be specified through the Name field of GASKET BEHAVIOR
[CONNECTOR BEHAVIOR] card. See also GENERAL REMARKS how to determine the name
of NAME parameter.
Keyword
Created by
Remarks
Set DEFINED option to YES (located at the top of GASKET BEHAVIOR [GASKET
BEHAVIOR] card) so as the specific *GASKET CONTACT AREA option to be written to the
output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE field to define the dependence of
contact area or width versus closure curves on temperature). DEPENDENCIES parameter is
supported if the data table defined in above manner contains other columns after the 'Temperature'
one. The number of these columns (var(i)) determines the number of DEPEDENCIES parameter.
Keyword
*GASKET ELASTICITY
Created by
Remarks
Set DEFINED option to YES (located at the top of GASKET BEHAVIOR [GASKET
BEHAVIOR] card) so as the specific *GASKET ELASTICITY option to be written to the output
file (.inp).
The temperature values may be specified only if DEP option (of each COMPONENT) is set to
YES. They are introduced in the last column for each selected COMPONENT respectively (Press
189
ANSA v13.x
the ? key in DATA TABLE to define the corresponding table). DEPENDENCIES parameter is
supported if the data table defined in above manner contains other columns after the 'Temperature'
one. The number of these columns (var(i)) determines the number of DEPEDENCIES parameter.
Keyword
*GASKET SECTION
Created by
MENUBAR>Windows>Properties>NEW>GASKET.
Remarks
Press the ? key in MID field of *GASKET SECTION [GASKET_SECTION] card and choose
between the material or gasket behavior so as to define the MATERIAL or BEHAVIOR parameter
respectively.
Specify the direction thickness by picking two grid points from the screen (Press F1 key in one of
the N1, N2 and N3 fields).
Type any name in Name field of the specific *GASKET SECTION [GASKET_SECTION]
card to specify the ELSET parameter. See also GENERAL REMARKS how to determine the
names of ELSET, MATERIAL, BEHAVIOR and ORIENTATION parameters.
Set DEFINED option to YES (located at the top of *GASKET SECTION
[GASKET_SECTION] card) so as the specific *GASKET SECTION option to be written to the
output file (.inp).
Keyword
Created by
Remarks
Set DEFINED option to YES (located at the top of GASKET BEHAVIOR [GASKET
BEHAVIOR] card) so as the specific *GASKET THICKNESS BEHAVIOR option to be written
to the output file (.inp).
The temperature values may be specified only if DEP option (of each DIRECTION) is set to YES.
They are introduced in the last column for each selected DIRECTION respectively (Press the ?
key in DATA TABLE to define the corresponding table according to the VARIABLE and TYPE
that is chosen in each case). DEPENDENCIES parameter is supported if the data table defined in
above manner contains other columns after the 'Temperature' one. The number of these columns
(var(i)) determines the number of DEPEDENCIES parameter.
190
Keyword
Created by
ANSA v13.x
*GEOSTATIC
Using AUXILIARIES>STEP>NEW and then selecting the *GEOSTATIC option into the pull
down menu of ANALYSIS section.
Remarks
Keyword
Created by
*GLOBAL DAMPING
Remarks
191
ANSA v13.x
Keyword
*HEADING
Created by
Remarks
Keyword
*HEAT TRANSFER
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *HEAT TRANSFER option into the pull
down menu of ANALYSIS section.
Remarks
Keyword
*HEATCAP
Created by
Using MENUBAR>Windows>Properties>HEATCAP
Remarks
Set DEFINED option to YES (located at the top of *HEATCAP [HEATCAP_PROP] card) so as
the specific *HEATCAP option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to DEP. They are introduced in
the last column of the table (Press the ? key in C-T field to define the capacitance-temperature
table). DEPENDENCIES parameter is supported if the data table defined in above manner contains
other columns after the 'Temperature' one. The number of these columns (var(i)) determines the
number of DEPEDENCIES parameter.
192
Keyword
ANSA v13.x
*HYPERELASTIC
Created by
Using
MENUBAR>Windows>Materials>NEW>MATERIAL
*HYPERELASTIC option to YES ('Elasticity'=HYPERELASTIC).
and
switching
the
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *HYPERELASTIC option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE to define the corresponding table
according to the N that is chosen).
Keyword
*HYPERFOAM
Created by
Using
MENUBAR>Windows>Materials>NEW>MATERIAL
*HYPERFOAM option to YES while 'Elasticity'=HYPERFOAM.
and
switching
the
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *HYPERFOAM option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE to define the corresponding table
according to the N that is chosen).
193
ANSA v13.x
Keyword
Created by
Remarks
Keyword
*INCLUDE
Use MENUBAR>Windows>Database>Includes.
2.
3.
Keep both flags (inline and read-only) inactive or activate only the read-only flag so as to
write out its reference in the main file.
Edit to the Name field of the specific include and type any name to specify the INPUT parameter.
See also GENERAL REMARKS how to determine the name of INPUT parameter.
*INCREMENTATION OUTPUT
Created by
Remarks
Press the Output Variables button and activate any variable to be written to the output database.
Select DYNAMIC, EXPLICIT ANALYSIS because *INCREMENTATION OUTPUT can be used
only in an Abaqus/Explicit analysis.
Keyword
Created by
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *INELASTIC HEAT FRACTION option to be written to the output file (.inp).
194
Keyword
ANSA v13.x
*INERTIA RELIEF
Created by
Remarks
To define a local coordinate system for PARAM=ORIENTATION, press the ? key in 'coordinate'
field to select an already existing coordinate system or to create a new one from COORDINATE
SYSTEMS HELP card.
Keyword
Created by
Remarks
The node set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the node set names.
The field values supported are at up to 5 temperature points.
Keyword
Created by
INIT.CONDIT.>INIT.COND.>FLUID PRESSURE>Node.
Remarks
195
Keyword
Created by
ANSA v13.x
INIT.CONDIT.>INIT.COND.>HARDENING>Element.
INIT.CONDIT.>INIT.COND.>HARDENING>Set.
Remarks
The element set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the element set names.
Up to 16 section points may be specified to define a piecewise hardening variation through the
thickness of a shell section.
Data lines for TYPE=HARDENING, CROSS SECTION can only be specified. Data lines for other
cases (REBAR etc.) are not supported.
Keyword
Created by
Remarks
The keyword is valid only if 'Output Format' option is switched to 6.5, 6.6, 6.7 or 6.8 (ABAQUS
Output Parameters window.
The INPUT parameter is supported only during input. In output, the data lines are always written
under keyword line (*INITIAL CONDTIONS, TYPE=NODE REF COORDINATE).
Keyword
Created by
INIT.CONDIT.>INIT.COND.>STRAIN>Element.
INIT.CONDIT.>INIT.COND.>STRAIN>Set.
Remarks
The element set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the element set names.
Up to 16 section points may be specified to define initial plastic strains within an element.
196
Keyword
ANSA v13.x
Created by
Remarks
ANSA assigns automatically the same element id with the corresponding membrane element ids
where the nodes belong to. If referenced mesh is specified with nodes that do not reside in
membrane elements then the reference coordinates cannot be written out.
The INPUT parameter is supported only during input. In output, the data lines are always written
under keyword line (*INITIAL CONDTIONS, TYPE=REF COORDINATE).
Keyword
Created by
INIT.CONDIT.>INIT.COND.>VELOCITY>Rotating Vel.
Remarks
The node set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the node set names.
Keyword
Created by
INIT.CONDIT.>INIT.COND.>STRESS>Element.
INIT.CONDIT.>INIT.COND.>STRESS>Set.
Remarks
The element set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the element set names.
Up to 16 section points may be specified to define initial stresses within an element.
197
Keyword
Created by
ANSA v13.x
Remarks
The node set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the node set names.
Up to 5 temperature values may be specified.
Press '?' key in 'file_name' field (when following case 3. to define FILE and subsequent parameters)
in order to select *.fil or *.odb file (through File Manager that opens) from which data will be read.
Keyword
Created by
INIT.CONDIT.>INIT.COND.>VELOCITY>Node.
INIT.CONDIT.>INIT.COND.>VELOCITY>Set.
Remarks
The node set names can be specified through the Name field of the specific SET [SET] card.
See also GENERAL REMARKS how to determine the node set names.
Specify the translational velocities through vx, vy and vz fields (1, 2, 3 DOF) and the rotational
velocities through vxr, vyr and vzr fields (4, 5, 6 DOF).
Keyword
Created by
*INTEGRATED OUTPUT
198
ANSA v13.x
Using AUXILIARIES>SECTION>Assistant, activating the 'Create integrated output for step' flag
of SECTION ASSISTANT-Preview card and pressing the '?' key in the corresponding field to
select the step in which the current *INTEGRATED OUTPUT will be defined. The 'SECTION
PLANE' field is automatically filled with the id of the created cross section.
Remarks
Press the Output Variables button and activate any variable to be written to the output database.
Select DYNAMIC, EXPLICIT ANALYSIS because *INCREMENTATION OUTPUT can be used
only in an Abaqus/Explicit analysis.
Press the ? key in SECTION PLANE field to create a new section by filling the fields of
SECTION [CUTTING_SURFACE] card as needed. In this case the SURFACE parameter is
specified. If the INTEGRATED OUTPUT SECTION option of SECTION
[CUTTING_SURFACE] card is set to YES the SECTION parameter is specified. The user is able
to select more than one sets at once in order to define more than one output requests quickly (when
switching to SURFACE or ELSET options).
The names of SURFACE and SECTION parameters can be specified through the Name field of
SECTION [CUTTING_SURFACE] card. See also GENERAL REMARKS how to determine the
names of SURFACE and SECTION parameters.
Keyword
Created by
Remarks
199
Keyword
ANSA v13.x
*INTERACTION OUTPUT
Created by
Remarks
Press the ? key in INTERACTION field to create a new interaction. If NSET field of
*INTERACTION OUTPUT [INTERACTION_ OUTPUT] card is specified, the NSET
parameter is written out instead of NAME parameter.
Press the Output Variables button and activate any variable to be written to the output database.
The NAME and NSET parameters of the created interaction can be determined through the
INTERACTION VARIABLES card (Output Variables button) as well. See also GENERAL
REMARKS how to determine the names of NAME and NSET parameters.
Keyword
*INTERACTION PRINT
Created by
Remarks
Press the ? key in INTERACTION field to create a new interaction. If NSET field of
*INTERACTION OUTPUT [INTERACTION_ OUTPUT] card is specified, the NSET
parameter is written out instead of NAME parameter.
Press the Output Variables button and activate any variable to be written to the output database.
The NAME and NSET parameters of the created interaction can be specified through the
INTERACTION VARIABLES card (Output Variables button). The other optional parameters
(FREQUENCY, SUMMARY, TOTALS) can be specified through this card as well. See also
GENERAL REMARKS how to determine the names of NAME and NSET parameters.
200
ANSA v13.x
Keyword
*JOINT
Created by
MENUBAR>Windows>Properties>NEW>JOINT
Remarks
Switch the desired SPRING_i or/and DASHPOT_i pull down menus to YES to define joint behavior
for the each of the six local directions.
See GENERAL REMARKS how to determine the names of ELSET and ORIENTATION
parameters.
Set DEFINED option to YES (located at the top of *JOINT [JOINT_PROP] card) so as the
specific *JOINT option to be written to the output file (.inp).
201
ANSA v13.x
Keyword
Created by
*KINEMATIC
Remarks
Keyword
Created by
*KINEMATIC COUPLING
Remarks
COUPLING
COUPLING
through
the
*COUPLING
The degrees of freedom to be constrained, may be specified either in Ci fields at each coupling
node or in C field if set of nodes is used (*COUPLING [COUPLING] card).
See GENERAL REMARKS how to determine the name of ORIENTATION parameter.
202
ANSA v13.x
Keyword
*LOAD CASE
Created by
AUXILIARIES>STEP>NEW and use 'New *LOAD CASE' option by right clicking on step item.
Remarks
Press ? key in Step field to define a step that is required for the load case definition (through
MENUBAR>windows>Database).
Type any name in Name field of *LAOD CASE card to specify the NAME parameter(through
MENUBAR>windows>Database). Left click on 'Name' column field of ACTIVE TASK card
(AUXILIARIES>STEP) to specify the name of current *LOAD CASE item. See also GENERAL
REMARKS how to determine the name of NAME parameter.
Press ? key in BOUNDARY/LOAD field, select the desired load or boundary condition from
the corresponding card and click INSERT button to include loads and boundary conditions within a
load case definition (through MENUBAR>windows>Database). Alternatively drag and drop
*BOUNDARY , *CLOAD and *DLOAD items in order to add or remove them from the current
*LOAD CASE item accordingly (through ACTIVE TASK card).
203
ANSA v13.x
Keyword
*M1
Created by
Remarks
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *M1 option to be written to the output file (.inp).
Switch 'M1 behavior' to ELASTIC and 'M1 variation' to LINEAR to define the corresponding
options.
All the properties (stiffness, axial force, strain etc.) are given in a tabular form through M1 D.
TABLE field (Press the ? key in M1 D. TABLE field to define the corresponding table, if
LINEAR option is specified the above field appears by setting M1 DEP option to YES).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
Keyword
*M2
Created by
Remarks
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *M2 option to be written to the output file (.inp).
Switch 'M2 behavior' to ELASTIC and 'M2 variation' to LINEAR to define the corresponding
options.
All the properties (stiffness, axial force, strain etc.) are given in a tabular form through M2 D.
TABLE field (Press the ? key in M2 D. TABLE field to define the corresponding table, if
LINEAR option is specified the above field appears by setting M1 DEP option to YES).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
204
Keyword
Created by
ANSA v13.x
*MASS
ELEMENTs>MASS>Node.
ELEMENTs>MASS>Set.
ELEMENTs>UTIL>Mass Balance.
Remarks
Type any name in Name field of the specific *ELEMENT MASS&*ELEMENT ROTARY
[MASS] card to specify the ELSET parameter. See also GENERAL REMARKS how to determine
the name of ELSET parameter.
If PER ELEMENT or PER ELEMENT AREA TYPE (*ELEMENT MASS&*ELEMENT
ROTARY [MASS] card) is selected, the mass points are written out in a *NONSTRUCTURAL
MASS keyword in case that ELEMENTs> MASS>Set is performed.
Keyword
*MASS DIFUSSION
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *MASS DIFUSSION option into the
pull down menu of ANALYSIS section.
Remarks
Keyword
*MATERIAL
Created by
MENUBAR>Windows>Materials>NEW>MATERIAL.
Remarks
Type any name in Name field of the specific MATERIAL [MATERIAL] card to specify the
NAME parameter. See also GENERAL REMARKS how to determine the name of NAME
parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *MATERIAL option to be written to the output file (.inp).In order to avoid the above
activate 'set default' or 'set default for prop=any section' options of an already existing MATERIAL
in MATDB. Then when creating a new MATERIAL or a section type (SHELL_SECTION,
SOLID_SECTION etc.) according to which type is activated in 'set default for prop' option
respectively, this will take the properties of the MATERIAL in MATDB and the DEFINED=YES
205
ANSA v13.x
automatically.
Keyword
*MEMBRANE SECTION
Created by
Remarks
Type any name in Name field of the specific SHELL SECTION & ELEMENT TYPE
[MEMBRANE SECTION] card to specify the NAME parameter. See also GENERAL
REMARKS how to determine the names of NAME, MATERIAL, CONTROLS and
ORIENTATION parameters.
The most simple way to define the NODAL THICKNESS parameter:
1. Use ELEMENTs>INFO>FILT.MOD.SHELL
2. Select the desired membrane elements defined by the specific *MEMEBANE SECTION
3. Type any value in t1, t2, t3, and t4 fields so as to define varying thickness in membrane
elements.
4. Activate the Output elements thickness flag in conjunction with - as NODAL
THICKNESS option through ABAQUS Output Parameters card during output.
If nodal thickness has been assigned at least in all nodes of an element then in all other elements
that reside in the same property will be assigned automatically nodal thickness during output.
Set DEFINED option to YES (located at the top of SHELL SECTION & ELEMENT TYPE
[MEMBRANE SECTION] card) so as the specific *MEMBRANE SECTION option to be written
to the output file (.inp).
Keyword
*MODAL DAMPING
Created by
Remarks
Press the Output Variables button and activate any variable to be written to the results file.
Alternatively, type the identifying keys for the modal variables, separated with commas, through
the corresponding (Identifying Keys) field of MODAL VARIABLES window.
206
ANSA v13.x
Press DEFINE button of DATA LINES section in order to specify the data lines according to the
selected PARAMETER and DEFINITION options. This way the data line can be repeated as many
as desired to define modal damping in different modes or frequencies.
Keyword
*MODAL DYNAMIC
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *MODAL DYNAMIC option into the
pull down menu of ANALYSIS section.
Remarks
Keyword
*MODAL FILE
Created by
Remarks
Press the Output Variables button and activate any variable to be written to the results file.
Alternatively, type the identifying keys for the modal variables, separated with commas, through
the corresponding (Identifying Keys) field of MODAL VARIABLES window.
Keyword
*MODAL OUTPUT
Created by
Remarks
Press the Output Variables button and activate any variable to be written to the output database.
Alternatively, type the identifying keys for the modal variables, separated with commas, through
the corresponding (Identifying Keys) field of MODAL VARIABLES window.
Keyword
*MODAL PRINT
207
ANSA v13.x
Created by
Remarks
Press the Output Variables button and activate any variable to be printed. Alternatively, type the
identifying keys for the modal variables, separated with commas, through the corresponding
(Identifying Keys) field of MODAL VARIABLES window.
Keyword
*MODEL CHANGE
Created by
Remarks
If TYPE=CONTACT is used, press DEFINE button and then the INSERT button to choose the
contact pair(s)( click or drag to select more than one CONTACT PAIRs and press ADD) that will
be removed or reactivated. The Ctrl, Shift and Ctrl+A keys also work for the selection of contact
pairs through CONATCT PAIRS LIST HELP card.
If TYPE=ELEMENT is used, type ? key in the appropriate field to choose the sets of elements
that will be removed or reactivated. The user is able to select more than one sets at once in order to
define more than one output requests quickly.
See GENERAL REMARKS how to determine the names of element set, the slave and master
surfaces.
Keyword
*MOLECULAR WEIGHT
Created by
Remarks
Set DEFINED option to YES (located at the top of FLUID BEHAVIOR [FLUID BEHAVIOR]
card) so as the specific *MOLECULAR WEIGHT option to be written to the output file (.inp).
208
Keyword
ANSA v13.x
*MONITOR
Created by
Remarks
Press F1 key either in NODE field to pick a node from the screen or in NSET field to select a
node set from the relative card. The node set should contain only one node. See also GENERAL
REMARKS how to determine the node set name.
Keyword
Created by
*MPC
CONSTRAINTs>MPC>CONSTRAINT>MANY NODES.
CONSTRAINTs>MPC>CONSTRAINT>TWO NODES.
CONSTRAINTs>MPC>CONSTRAINT>SET.
CONSTRAINTs>MPC>MESH.REF>NODES.
CONSTRAINTs>MPC>MESH.REF>SET.
CONSTRAINTs>MPC>MESH.REF>AUTO.
Remarks
Use options from CONSTRAINT menu to create BEAM, TIE, PIN and LINK types and options
from MESH>REF menu for LINEAR type.
When CONSTRAINTs>MPC>CONSTRAINT>TWO NODES is performed (TYPE= BEAM) the
displacements and rotations of the second selected node are constrained to the displacements and
rotations of the first selected node.
When MESH.REF>SET option is used each of the three sets should contain only one node. ANSA
cannot respect the order of nodes as written in *NSET keyword and so the definition of LINEAR
MPCs with node sets comprised of more than one node may be changed and become not valid.
See GENERAL REMARKS how to determine the node sets names. Node set names for MASTER
(independent) nodes are supported only during input.
Keyword
*MULLINS EFFECT
209
Created by
Remarks
ANSA v13.x
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *MULLINS EFFECT option to be written to the output file (.inp).
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in DATA TABLE to define the corresponding r-m-bT table).
210
ANSA v13.x
Keyword
Created by
*NMAP
1.
Using AUXILIARIES>NMAP>NEW (either from button at bottom of *NMAP card or by
right clicking inside area of card), switching to SET or INCLUDE to select a set or an include file
(press ? key in the corresponding field), switch TYPE=RECTANGULAR in second pull down
menu of *NMAP card, enforcing any geometry function (TRANSLATION, ROTATION, SCALE,
TRANS123, TRANS CS) and pressing the APPLY button to declare the definition (*NMAP
card).
The
NMAP
will
be
defined
for
TYPE
=
RECTANGULAR
,DEFINITION=COORDINATES in the above case. DEFINITION=NODES is not supported for
this type.
2.
Using AUXILIARIES>NMAP>NEW (either from button at bottom of *NMAP card or by
right clicking inside area of card), switching to SET or INCLUDE to select a set or an include file
(press ? key in the corresponding field), switch TYPE=OPTION in second pull down menu of
*NMAP card, switch OPTION to TRANSLATION, ROTATION or SCALE, select between
COORDINATES and NODES in DEFINITION menu to specify the corresponding option for
DEFINITION parameter and pressing the APPLY button to declare the definition (*NMAP
card). The NMAP will be defined for TYPE = TRANSLATION, ROTATION, SCALE,
DEFINITION = COORDINATES, NODES according to the selected options in OPTION and
DEFINITION menus. Perform TRANS123 or/and TRANS CS for TYPE=TRANSLATION and
ROTATION, DEFINITION=COORDINATES.
Remarks
Type any name in NAME field of the selected SET to specify the name of the NSET parameter.
See also GENERAL REMARKS how to determine the node set name.
Switch first pull down menu to blank in order to disable the current NMAP definition. This way
the NMAP card exists in database and it is not needed to delete and redefine it any time it is
desired or not in output.
Control the default type (Rectangular or option) when creating new NMAPs by the setting
'Default Abaqus NMAP type' existing in Windows>Options...>Settings>DECKS.
Keyword
Created by
*NO COMPRESSION
211
Remarks
Keyword
Created by
Remarks
Keyword
Created by
ANSA v13.x
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *NO COMPRESSION option to be written to the output file (.inp).
*NO TENSION
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *NO TENSION option to be written to the output file (.inp).
*NODAL THICKNESS
Remarks
212
Keyword
ANSA v13.x
*NODE
Created by
Using any function from the NODE>NEW button (NUMERIC, RELATIVE, INSERT, LINE).
Remarks
Assign a rectangular, cylindrical and spherical coordinate system in SYSTEM field of *NODE
[NODE] card to define SYSTEM=R, SYSTEM=C and SYSTEM=S at the node respectively. The
node is displayed in the new local coordinate system if SYSTEM field is specified.
Keyword
Created by
Remarks
*NODE FILE
Press the Output Variables button and activate any variable to be written to the results file.
Alternatively, type the identifying keys for the nodal variables, separated with commas, through
the corresponding (Identifying Keys) field of NODAL VARIABLES window.
Press F1 or ? key in NSET field to select a node set from the relative card for which the output
is being written to the results file. The user is able to select more than one sets at once in order to
define more than one output requests quickly. See also GENERAL REMARKS how to determine
the name of NSET parameter.
Keyword
*NODE OUTPUT
Created by
Remarks
Press the Output Variables button and activate any variable to be written to the output database.
Alternatively, type the identifying keys for the nodal variables, separated with commas, through
the corresponding (Identifying Keys) field of NODAL VARIABLES window.
Press F1 or ? key in NSET field to select a node set from the relative card for which the output
is being written to the output database. The user is able to select more than one sets at once in
order to define more than one output requests quickly. See also GENERAL REMARKS how to
213
ANSA v13.x
Keyword
*NODE PRINT
Created by
Remarks
Press the Output Variables button and activate any variable to be printed in the data file.
Alternatively, type the identifying keys for the nodal variables, separated with commas, through
the corresponding (Identifying Keys) field of NODAL VARIABLES window.
Press F1 or ? key in NSET field to select a node set from the relative card for which the output
is being printed in the data file. The user is able to select more than one sets at once in order to
define more than one output requests quickly. See also GENERAL REMARKS how to determine
the name of NSET parameter.
Keyword
*NONSTRUCTURAL MASS
Created by
Remarks
Edit to the elements set over which the nonstructural mass is distributed and type any name in
Name field of the specific SET [SET] card to specify the name of the ELSET parameter. See
also GENERAL REMARKS how to determine the name of ELSET parameter.
When PER ELEMENT AREA option is used, the specified mass is automatically calculated per
element area (MASS/ area of all elements included in the set) and it is written out with
UNITS=MASS PER AREA parameter during output.
Keyword
Created by
*NSET
214
Remarks
ANSA v13.x
The NSET parameter can be specified through the Name field of the specific SET [SET]card.
See also GENERAL REMARKS how to determine the name of NSET parameter.
Switch AUXILIARY option to NO and 'DEFINED' to YES so as the specific *NSET option to be
exported (SET [SET] card).
215
ANSA v13.x
Keyword
Created by
*ORIENTATION
Remarks
for
for
DEFINITION=COORDINATES
DEFINITION=COORDINATES
and
and
SYSTEM=
SYSTEM=
The NAME parameter can be specified through the Name field of the specific coordinate system
card. See also GENERAL REMARKS how to determine the name of NAME parameter.
Specify 'RID' field (Local coordinate system card) in order to define a local coordinate system in
relation to another already existing coordinate system (just for DEFINITION =COORDINATES,
COORDs>CORD functions).
Select the local direction from 'rotation axis' menu in order to specify additional rotation for this
axis (through 'rotation angle' field).
Keyword
Created by
*OUTPUT
216
ANSA v13.x
Using AUXILIARIES>SECTION>Assistant, activating the 'Create integrated output for step' flag
of SECTION ASSISTANT-Preview card and pressing the '?' key in the corresponding field to
select the step in which the current *OUTPUT, HISTORY will be defined.
Remarks
Press F1 or ? key in FILTER field to create a new filter so as to specify the FILTER parameter.
See also GENERAL REMARKS how to determine the name of FILTER parameter.
217
ANSA v13.x
Keyword
*PHYSICAL CONSTANTS
Created by
AUXILIARIES>STEP>*PHYSICAL CONSTANTS.
Remarks
The SPL REFERENCE PRESSURE parameter is written out provided the 'Output Format' is
switched to 6.8 (ABAQUS Output Parameters window).
Keyword
Created by
Remarks
Each row of the specified data table implies one data line during output. DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *PLANAR TEST DATA option to be written to the output file (.inp).
218
Keyword
ANSA v13.x
*PLASTIC
Created by
Remarks
Press the ? key in DATA TABLE field to define the corresponding variables at each
HARDENING option in a tabular form. The temperature values are introduced in the last column
of the table.
The RATE parameter can be specified through the table definition. Edit to the Rate field and type
a value. Have in mind to create a TABLE and not a D. TABLE in this case. DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *PLASTIC option to be written to the output file (.inp).
Keyword
Created by
*PRE-TENSION SECTION
Remarks
Type any name in Name field of the SET that is used to define the surface, so as to specify the
name of the SURFACE parameter. See also GENERAL REMARKS how to determine the name of
SURFACE parameter.
If the specific set is needed to be output only as *SURFACE, switch the Output as: pull down
menu to Surface (SET [SET] card).
The normal to the section can be defined through the X1, X2 and X3 fields.
219
ANSA v13.x
The node set name (for NODE parameter) is supported only during input. The element set name is
not supported.
In Assistant function the user is able to prescribe the pre-tension load or tightening adjustment on
pre-tension node by activating the 'Create *CLOAD' or 'Create *BOUNDARY' flags respectively.
The pre-tension node is an arbitrary free grid created automatically by this tool.
Keyword
*PREPRINT
Created by
AUXILIARIES>STEP>*PREPRINT.
Remarks
MASS PROPERTY parameter is written out only if 'Abaqus/Explicit output' flag is active and
'Output Format' is set to 6.8 (ABAQUS Output Parameters window). The 'Abaqus/Explicit output'
flag is automatically activated when DYNAMIC, EXPLICIT ANALYSIS is selected through
STEP card.
Keyword
*PRESSURE PENETRATION
Created by
AUXILIARIES>CONTACT>PRESSURE PENETRATION>NEW
Remarks
The SLAVE and MASTER parameters are defined through CONTACT field (*PRESSURE
PENETRATION [*PRESSURE PENETRATION] card) by selecting a contact pair in the relative
list that opens with '?' key. Thus, the above parameters are filled automatically by the master and
slave surfaces of the selected contact respectively.
Press '?' key in STEP field to select the step that the current pressure penetration will reside in.
See GENERAL REMARKS how to determine the names of MASTER, SLAVE and AMPLITUDE
parameters.
Keyword
Created by
220
Remarks
ANSA v13.x
The MASS parameter is written out provided the 'Output Format' is switched to 6.7 or 6.8
(ABAQUS Output Parameters window).
221
ANSA v13.x
Keyword
Created by
*RADIATE
LOADs>RADIATE>Element.
LOADs>RADIATE>Set.
Remarks
See GENERAL REMARKS how to determine the name of AMPLITUDE and the element set
names.
For sets the option 'Output as: should be switched to Set in order to output *RADIATE keyword.
If Radiate flag into RESET region of STEP card is active, all of *RADIATE options in this
step obtain OP=NEW parameter.
Keyword
*RANDOM RESPONSE
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *RANDOM RESPONSE option into
the pull down menu of ANALYSIS section.
Remarks
Keyword
Created by
Remarks
*RATE DEPEDENT
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *RATE DEPEDENT option to be written to the output file (.inp).
222
ANSA v13.x
The temperature values may be specified only if DEP option is set to YES. They are introduced in
the last column of the table (Press the ? key in TEST DATA to define the corresponding table).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
Keyword
Created by
*REBAR LAYER
Remarks
Keyword
Press ? key in mat i field to define the material forming the rebar layer. The name can be
specified trough the Name field of the specific MATERIAL [MATERIAL] card. See also
GENERAL REMARKS how to determine the name of ORIENTATION parameter as well as the
material names.
*RELEASE
Created by
Using ELEMENTs>BEAM to create beams and choosing the desired release combination codes
(M1, M2, T, M1-M2, M1-T, M2-T, ALLM) from the RELEASE S1 and RELEASE S2 pull
down menus respectively (BEAM ELEMENT CARD).
Remarks
Keyword
Created by
*RESTART
223
Remarks
ANSA v13.x
When method 1. is used, leave ANALYSIS menu blank to fit parameters of READ and WRITE
according to Standard analyses and switch to EXPLICIT to adjust READ and WRITE parameters
according to Explicit analyses.
The CYCLE parameter of READ is exported only if the 'Output Format' is switched to 6.8
(ABAQUS Output Parameters window).
Keyword
*RETAINED EIGENMODES
Created by
Remarks
The keyword is valid only if the 'Output Format' is switched to 6.8 and earlier (ABAQUS Output
Parameters window).
Keyword
Created by
1. BOUNDARY>RETAINED>Nodes or Set
2. Automatically by using AUXILIARIES>SUBSTR>LIST>NEW. When finishing with
substructure definition the retained nodal dofs are generated during output. Press '?' key in
'Additional Retained Nodal DOFS set:' field of SUBSTRUCTURE ANALYSIS CREATOR
card to select a set in which additional nodal dofs will be defined. (see also tutorial 11 of docs
folder included in distribution package for more details concerning the substructure definitions).
Remarks
If following method 1., press '?' key in STEP filed of *RETAINED NODAL DOFS card to select
the *SUBSTRUCTURE GENERATE step to be assigned for these retained nodal dofs. If
following method 2. the STEP field is filled by the step id specified in 'Substructure Step:' field.
See also GENERAL REMARKS how to determine name of node sets which define the retained
nodal dofs.
224
Keyword
Created by
ANSA v13.x
*RIGID BODY
AUXILIARIES>R.BODY>NEW>ELSET.
AUXILIARIES>R.BODY>NEW>ANALYTICAL SURFACE.
Remarks
Keyword
Created by
The names of ANALYTICAL SURFACE, ELSET, PIN NSET and TIE NSET parameters can be
specified through the Name field of the corresponding card (SET [SET] and ANALYTICAL
SURFACE [SURFACE] cards). See also GENERAL REMARKS how to determine the names of
the above parameters. The node set name of REF NODE parameter is supported only during input.
*RIGID SURFACE
Remarks
Keyword
Created by
The name of NAME parameter can be specified through the Name field of the corresponding
card (ANALYTICAL SURFACE [SURFACE]). See also GENERAL REMARKS how to
determine the name of NAME parameter.
*ROTARY INERTIA
Using ELEMENTs>MASS>Node to create mass points and typing a value at least in one of the
I11, I22, I33, I12, I13and I23 fields of *ELEMENT MASS & *ELEMENT ROTARYI
[MASS] card.
Using ELEMENTs>MASS>Set and typing a value at least in one of the I11, I22, I33, I12,
I13and I23 fields of *ELEMENT MASS & *ELEMENT ROTARY [MASS] card while ON
EACH NODE TYPE is set.
225
Remarks
ANSA v13.x
The name of ELSET parameter can be specified through the Name field of the corresponding
card (*ELEMENT MASS & *ELEMENT ROTARYI [MASS]). See also GENERAL
REMARKS how to determine the names of ELSET and ORIENTATION parameter
226
ANSA v13.x
Keyword
*SECTION CONTROLS
Created by
AUXILIARIES>CONTROLS>*SECTION CONTOLS>NEW.
Remarks
Keyword
Created by
Remarks
Keyword
*SELECT EIGENMODES
Created by
Remarks
The keyword is valid only if the 'Output Format' is switched to 6.9 (ABAQUS Output Parameters
window).
227
Keyword
ANSA v13.x
*SFILM
Created by
LOADs>FILM>Set.
Remarks
For sets the option 'Output as: should be switched to Surface in order to output *SFILM keyword.
If Film flag into RESET region of STEP card is active, all *SFILM options in this step
acquire OP=NEW parameter.
The surface name obtains the same name with the set that is used to define the surface. See also
GENERAL REMARKS how to determine the surface and film property names as well as the
names of AMPLITUDE and FILM AMPLITUDE parameters.
Keyword
Created by
*SHEAR CENTER
Remarks
Keyword
*SHEAR FAILURE
Created by
Remarks
The temperature values (of TYPE=TABULAR) may be specified only if DEP option is set to
YES. They are introduced in the 4th column of the table (Press the '?' key in DATA TABLE field
to define the table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *SHEAR FAILURE option to be written to the output file (.inp).
228
Keyword
Created by
ANSA v13.x
Remarks
Each row of the specified data table implies one data line during output
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *SHEAR TEST DATA option to be written to the output file (.inp).
Keyword
Created by
*SHELL SECTION
Remarks
or
LAMINATE
for
*SHELL
229
ANSA v13.x
If nodal thickness has been assigned at least in all nodes of an element then in all other elements
that reside in the same property will be assigned automatically nodal thickness during output.
The SHELL THICKNESS parameter is defined automatically by following case A) of
*DISTRIBUTION keyword. See also Remarks of *DISTRIBUTION keyword for details
regarding the determination of the name of this parameter.
Use AUXILIARIES>LAMINATE tool for further manipulation of the layers for a COMPOSITE
or LAMINATE property. The advantage of a LAMINATE property is that it is possible to remove
or add shells in the creation of new layers. So the LAMINATE property is broken in more
composite properties in output and the number of them depends on the shells participating in each
layer. Refer also to users_guide.pdf for details about this tool.
See GENERAL REMARKS how to determine the names of ELSET, MATERIAL, CONTROLS
and ORIENTATION parameters.
Set DEFINED option to YES (located at the top of SHELL SECTION & ELEMENT TYPE
[SHELL_SECTION] card) so as the specific *SHELL SECTION option to be written to the
output file (.inp).
Keyword
Created by
of SHELL TO
Remarks
The CONSTRAIN NAME parameter may be specified in Name field of SHELL TO SOLID
COUPLING card. See also GENERAL REMARKS how to determine the names of
CONSTRAIN NAME parameter.
When New by proximity is used to create shell to solid coupling the 'search distance' and
'projection distance' options correspond to INFLUENCE DISTANCE and POSITION
TOLERANCE parameters respectively.
230
Keyword
Created by
ANSA v13.x
Remarks
Each row of the specified data table implies one data line during output.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *SIMPLE SHEAR TEST DATA option to be written to the output file (.inp).
Keyword
Created by
*SOLID SECTION
MENUBAR>Windows>Properties>NEW>SOLID
MENUBAR>Windows>Properties>NEW>TRUSS
Remarks
See GENERAL REMARKS how to determine the names of ELSET, MATERIAL, CONTROLS
and ORIENTATION parameters.
Set DEFINED option to YES (located at the top of SOLID SECTION & ELEMENT TYPE
[SOLID_SECTION] card) so as the specific *SOLID SECTION option to be written to the
output file (.inp).
Keyword
Created by
*SPECIFIC HEAT
231
Remarks
Keyword
ANSA v13.x
If DEP option is set to YES the specific heat is defined as a function of temperature (Press the ?
key in DATA TABLE field to define the specific heat - temperature table). DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
DEPEDENCIES parameter.
*SPRING
Created by
MENUBAR>Windows>Properties>NEW>SPRING.
Remarks
Switch to Fixed Dir. TYPE to define spring behavior for SPRING1 and SPRING2 elements and
Axial TYPE for SPRINGA elements.
Switch to NONLINEAR BEHAVIOR to include this parameter during output (nonlinear spring
behavior).
If DEP option is set to DEP the spring stiffness is defined as a function of frequency (only for
linear spring behavior) and temperature (Press the ? key in S-F-T and D-F-T fields to define
the tables for linear and non-linear spring behavior respectively). DEPENDENCIES parameter is
supported if the data table defined in above manner contains other columns after the 'Temperature'
one. The number of these columns (var(i)) determines the number of DEPEDENCIES parameter.
See GENERAL REMARKS how to determine the names of ELSET and ORIENTATION
parameters.
Set DEFINED option to YES (located at the top of *SPRING [SPRING_PROP] card) so as the
specific *SPRING option to be written to the output file (.inp).
Keyword
*SRADIATE
Created by
LOADs>RADIATE>Set.
Remarks
For sets the option 'Output as: should be switched to Surface in order to output *SRADIATE
keyword.
If Radiate flag into RESET region of STEP card is active, all of *SRADIATE options in this
step acquire OP=NEW parameter.
The surface name obtains the same name with the set that is used to define the surface. See also
GENERAL REMARKS how to determine the surface name as well as the name of AMPLITUDE
parameter.
232
Keyword
ANSA v13.x
*STATIC
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *STATIC option into the pull down
menu of ANALYSIS section.
Remarks
Keyword
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *STEADY STATE DYNAMICS option
into the pull down menu of ANALYSIS section.
Remarks
Keyword
Created by
Remarks
233
ANSA v13.x
*STEP
Created by
AUXILIARIES>STEP>NEW.
Remarks
All available parameters are placed at the top section of the STEP window.
See GENERAL REMARKS how to determine the name of NAME parameter.
Keyword
*SUBCYCLING
Created by
Using AUXILIARIES>SUBCYCL.>NEW.
Remarks
The element set of a subcycling zone is defined through ELSET field (press the ? key to select
existing sets from the SETS HELP card). See also GENERAL REMARKS how to determine the
name of ELSET parameter.
Since the above keyword is valid only for a Abaqus/Explicit analysis in order to output the
'Abaqus/Explicit output' flag of Other Options section of Miscellaneous tab should be activated
during output (ABAQUS Output Parameters window). If *DYNAMIC, EXPLICIT ANALYSIS is
selected from STEP card (AUXILIARIES>STEP>NEW) then the above flag is automatically
activated. In addition, the 'Output Format' flag should be set equal to 6.8 in order to write out the
keyword.
Keyword
Created by
*SUBSTRUCTURE GENERATE
Remarks
234
ANSA v13.x
To specify the substructure identifier of TYPE parameter either type a value in 'TYPE Z' field of
'Parameters' button (STEP card) or type a value in 'ELEMENT, TYPE=Z' field of
SUBSTRUCTURE ANALYSIS CREATOR card if following the method 2. to define the
keyword (this case it is possible to press 'Edit' button to open STEP card and specify TYPE
parameter through 'Parameter' button).
See also GENERAL REMARKS how to determine the element and node set name when defining
ELSET and NSET parameters respectively (through 'Parameters' button in STEP card).
Keyword
Created by
Following one of the methods to define *SUBSTRUCTURE GENERATE step (see also the
*SUBSTRUCTURE GENERATE keyword), switching to *SUBSTRUCTURE MATRIX OUTPUT
Keyword and pressing the INSERT button to declare the definition.
Remarks
Keyword
Created by
*SUBSTRUCTURE PROPERTY
Remarks
When following the method 2. type a value in Position Tolerance field in order to specify the
POSITION TOL parameter of the keyword (the POSITION TOL filed of card is filled by this
option).
Specify values in tx, ty, tz fields of SUBSTRUCTURE PROPERTY card in order to perform
translation of substructures in each global direction. Do the same in fields rax, ray, raz, rbx, rby,
rbz, angle to perform rotation in substructures and reflections when typing values in pax, pay, paz,
pbx, pby, pbz, pcx, pcy, pcz fields.
Set DEFINED option to YES (located at the top of *SUBSTRUCTURE PROPERTY
[SUBSTRUCTURE_PROPERTY] card) so as the specific *SUBSTRUCTURE PROPERTY
keyword to be written to the output file (.inp).
235
ANSA v13.x
See also GENERAL REMARKS how to determine name when of ELSET parameter.
Keyword
Created by
*SURFACE, TYPE=ELEMENT
Remarks
The REGION TYPE and TRIM parameters can be defined through the *CONTACT
DEFINITION [CONTACT_PAIR] and *TIE DEFINITION [CONTACT_PAIR] cards.
236
ANSA v13.x
The MAX RATIO, NO OFFSET, NO THICK and SCALE THICK parameters can be defined
through *CONTACT DEFINITION [CONTACT_PAIR]card.
The NAME parameter obtains the same name with the name of the set that defines the surface. See
also GENERAL REMARKS how to determine the name of NAME parameter.
Switch AUXILIARY option to NO so as the specific *SURFACE option to be exported (SET
[SET] card).
Keyword
Created by
*SURFACE, TYPE=NODE
Using AUXILIARIES>SET>INFO>NEW to create new sets and switching Output as: pull down
menu to Surface. The sets should contain only nodes and ranges of nodes.
CONSTRAINTs>KINEM>NODES or SET.
CONSTRAINTs>DISTR>NODES, SET or FACET.
AUXILIARIES>CONTACT>INFO>NEW>CONTACT (Press the ? key in SSID and MSID
fields of *CONTACT DEFINITION [CONTACT_PAIR] card to select the set that will define
the surface while NODE SLAVE and/or NODE MASTER is set).
AUXILIARIES>CONTACT>INFO>NEW>TIE (Press the ? key in SSID and MSID fields of
*TIE DEFINITION [CONTACT_PAIR] card to select the set that will define the surface while
NODE SLAVE and/or NODE MASTER is set).
Remarks
The REGION TYPE and TRIM parameters can be defined through the *CONTACT
DEFINITION [CONTACT_PAIR] and *TIE DEFINITION [CONTACT_PAIR] cards.
The MAX RATIO, NO OFFSET, NO THICK and SCALE THICK parameters can be defined
through *CONTACT DEFINITION [CONTACT_PAIR]card.
The NAME parameter obtains the same name with the name of the set that defines the surface. See
also GENERAL REMARKS how to determine the name of NAME parameter. Only for couplings,
ANSA automatically assigns an arbitrary surface name with the following format: NAME =
SURF_COUPLING_(arbitrary number).
Switch AUXILIARY option to NO so as the specific *SURFACE option to be exported (SET
[SET] card).
237
Keyword
Created by
ANSA v13.x
Remarks
The REGION TYPE and TRIM parameters can be defined through the *CONTACT
DEFINITION [CONTACT_PAIR] and *TIE DEFINITION [CONTACT_PAIR] cards.
The MAX RATIO, NO OFFSET, NO THICK and SCALE THICK parameters can be defined
through *CONTACT DEFINITION [CONTACT_PAIR]card.
The NAME parameter can be specified through the Name field of. ANALYTICAL SURFACE
[SURFACE] card. See also GENERAL REMARKS how to determine the name of NAME
parameter.
Keyword
Created by
AUXILIARIES>SECTION>INFO>NEW.
AUXILIARIES>SECTION>Assistant.
Remarks
The NAME parameter can be specified through the Name field of. SECTION
[CUTTING_SURFACE] card. See also GENERAL REMARKS how to determine the name of
NAME parameter and the element set.
DEFINITION parameter is written out if 'Output Format' is switched to 6.7 or 6.8 (ABAQUS
Output Parameters window).
238
Keyword
Created by
ANSA v13.x
*SURFACE BEHAVIOR
Remarks
Keyword
*SURFACE INTERACTION
Created by
AUXILIARIES>S.INTER>INFO>NEW.
Remarks
The out-of-plane thickness of the surface or cross-sectional area for every node in the node-based
surface can be specified through THICKNESS field of SURFACE INTERACTION/CONTACT
PROPERTIES [SURFACE_INTERACTION] card.
The NAME parameter can be specified through the Name field of. SURFACE INTERACTION/
CONTACT PROPERTIES [SURFACE_ INTERACTION] card. See also GENERAL REMARKS
how to determine the name of NAME parameter.
Keyword
Created by
Remarks
The surface names are the same with the names of the sets used to define the surfaces. See also
GENERAL REMARKS how to determine the surface names.
Leave the SURFACE field blank to omit surface names during output (blank data line).
See also *CONTACT keyword because it is required for the *SURFACE PROPERTY
ASSIGNMENT.
239
ANSA v13.x
Leave 'STEP' field blank to write out as model data or else specify the step id of an
ABAQUS/Explicit analysis to write out as history data. Due to the fact that it is valid only in an
ABAQUS/Explicit analysis activate 'Abaqus Explicit Output' flag during output.
The primary and secondary feature edge criteria are exported only if 'Abaqus Version' menu is
switched to 6.7 or 6.8 during output.
Keyword
Created by
*SURFACE SECTION
MENUBAR>Windows>Properties>NEW>SURFACE.
Automatically by AUXILIARIES>AIRBAG>Enclose Cavity.
Remarks
The ELSET parameter can be specified through the Name field of. *SURFACE SECTION
[SURFACE_SECTION] card. See also GENERAL REMARKS how to determine the name of
ELSET parameter.
Set DEFINED option to YES (located at the top of SURFACE SECTION
[SURFACE_SECTION] card) so as the specific *SURFACE SECTION option to be written to the
output file (.inp).
Keyword
Created by
*SYSTEM
Edit to the *NODE [NODE] card of a node (NODE>INFO>INFO) and specify the SYSTEM
field (Press ? key to select an existing local system or to create a new one).
Remarks
240
ANSA v13.x
Keyword
*TEMPERATURE
Created by
Remarks
See GENERAL REMARKS how to determine the node set names and the name of AMPLITUDE
parameter.
If Temperature flag into RESET region of STEP card (AUXILIARIES>STEP>NEW) is active,
all of *TEMPERATURE options in this step enquire OP=NEW parameter.
Up to 5 temperature points are supported.
Press '?' key in 'file_name' field (when using File option to define FILE parameter and subsequent
parameters) in order to select *.fil or *.odb file (through File Manager that opens) from which data
will be read.
Keyword
*THERMAL EXPANSION
Created by
Remarks
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *THERMAL EXPANSION option to be written to the
output file (.inp).
If TE DEP option is set to YES the specific thermal coefficient is defined as a function of
temperature (Press the ? key in TE D. TABLE field to define the specific thermal coefficient temperature table). DEPENDENCIES parameter is supported if the data table defined in above
manner contains other columns after the 'Temperature' one. The number of these columns (var(i))
determines the number of DEPEDENCIES parameter.
Keyword
*TIE
241
ANSA v13.x
Created by
AUXILIARIES>CONTACT>INFO>NEW>TIE.
Remarks
The name of NAME parameter can be specified through Name field of *TIE DEFINITION
[CONTACT_PAIR] card. See also GENERAL REMARKS how to determine the name of MAME
parameter, the surface (master, slave) and node set names.
Keyword
*TORQUE
Created by
Remarks
Set DEFINED option to YES (located at the top of BEAM SECTION & ELEMENT TYPE
[BEAM SECTION] card) so as the specific *TORQUE option to be written to the output file
(.inp).
Switch 'TQ behavior' to ELASTIC and 'TQ variation' to LINEAR to define the corresponding
options.
All the properties (stiffness, axial force, strain etc.) are given in a tabular form through TQ D.
TABLE field (Press the ? key in TQ D. TABLE field to define the corresponding table, if
LINEAR option is specified the above field appears by setting TQ DEP option to YES).
DEPENDENCIES parameter is supported if the data table defined in above manner contains other
columns after the 'Temperature' one. The number of these columns (var(i)) determines the number
of DEPEDENCIES parameter.
Keyword
*TRANSFORM
Created by
Edit to the *NODE [NODE] card of a node (NODE>INFO>INFO) and specify the
TRANSFORM field (Press ? key to select an existing local system or to create a new one).
Remarks
The NSET parameter obtains the same name with the selected coordinate system. The *NSET
option is automatically created during output and contains all the nodes in which the
TRANSFORM field has been specified. See also GENERAL REMARKS how to determine the
name of NSET parameter.
The TYPE parameter is determined by the type of selected coordinate system. Thus, if rectangular
system is selected then TYPE=R will be defined, if cylindrical system TYPE=C and if spherical
system TYPE=S.
242
Keyword
Created by
ANSA v13.x
Remarks
Keyword
*TRS
Created by
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *TRS option to be written to the output file (.inp).
243
ANSA v13.x
Keyword
Created by
Remarks
Each row of the specified data table implies one data line during output. DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *UNIAXIAL TEST DATA option to be written to the output file (.inp).
Keyword
*USER MATERIAL
Created by
Remarks
Each constant can be specified through 'constants' field separated with commas.
244
ANSA v13.x
Keyword
Created by
Remarks
The ELSET parameter obtains the same name with name of the set that is used. The user is able to
select more than one sets at once in order to define more than one output requests quickly. See also
GENERAL REMARKS how to determine the name of ELSET parameter.
Select DYNAMIC, EXPLICIT ANALYSIS because *VARIABLE MASS SCALING makes sense
only in an Abaqus/Explicit analysis.
Keyword
*VISCO
Created by
Using AUXILIARIES>STEP>NEW and then selecting the *VISCO option into the pull down
menu of ANALYSIS section.
Remarks
Keyword
*VISCOELASTIC
Created by
Using
MENUBAR>Windows>Materials>NEW>MATERIAL
*VISCOELASTIC option to YES.
Remarks
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *HYPERELASTIC option to be written to the output file (.inp).
and
switching
the
245
ANSA v13.x
In options where 'DATA' field appears, specify the data lines in tabular form (press ? key in
'DATA' field and DATA TABLE window will appear to specify data values in rows and
columns, each row corresponds to one data line).
Keyword
Created by
Remarks
Each row of the specified data table implies one data line during output. DEPENDENCIES
parameter is supported if the data table defined in above manner contains other columns after the
'Temperature' one. The number of these columns (var(i)) determines the number of
DEPEDENCIES parameter.
Set DEFINED option to YES (located at the top of MATERIAL [MATERIAL] card) so as the
specific *VOLUMETRIC TEST DATA option to be written to the output file (.inp).
246