Académique Documents
Professionnel Documents
Culture Documents
LocalLoadingTool(LLT)
ForTELIUMTerminals
Ingenico190192avenueCharlesdeGaulle92200NeuillysurSeine
Tl.33(0)146258200Fax33(0)147725695ingenico@.ingenico.com
Copyright2009Ingenico
Allrightsreserved
900001549R1100001_2961074102/96
Copyright2009Ingenico
Allrightsreserved
900001549R1100001_2961074103/96
Copyright2009Ingenico
Allrightsreserved
CONTENTS
1. INTRODUCTION _______________________________________________6
2. Environment__________________________________________________6
3. Softwareinstallation ___________________________________________6
4. Softwareremoval _____________________________________________ 7
5. UseofLLTfunctions ___________________________________________ 7
5.1. Softwarecomponentdownloading ______________________________________ 7
5.2. Parameterfilesdownloading ___________________________________________ 7
5.3. Knowingthepresentcomponentlistintheterminal ________________________ 8
5.4. Uploadingdiagnosticfiles ______________________________________________ 8
5.5. Connectingtotheterminal _____________________________________________ 8
5.6. Disconnectingtotheterminal __________________________________________ 9
5.7. Selectionandfiletransfer ______________________________________________ 9
5.8. Displayingandconsultation ____________________________________________ 11
5.9. Displayingandconsultation ____________________________________________14
6. FileLIFECOUNTER.DIA_________________________________________ 17
6.1. FileLIFECOUNTER.DIA_________________________________________________ 17
7. FileBOOSTERDIA ____________________________________________ 17
7.1. ConsultingofBoosterdiafiles: _________________________________________ 17
8. FileAPPDEFAULT.DIA _________________________________________ 18
8.1. ConsultationofAppDefault.dia.files:_____________________________________18
9. FileAPPCOUNTER.DIA _________________________________________ 18
9.1. ConsultationofAppCounter.dia.files: ____________________________________18
900001549R1100001_2961074104/96
Copyright2009Ingenico
Allrightsreserved
FileLLT.PRM ____________________________________________________ 20
10.3.
FileLLT.LNG _____________________________________________________ 20
10.4.
FileLLT.BMK ____________________________________________________ 20
10.5.
ChangingLLTlanguage ____________________________________________ 20
10.6.
Defininganewtranslationlanguage _________________________________ 20
10.7.
LLTuseincommandmode __________________________________________ 21
10.8.
DisplayingtheUSBconnectionportnumber __________________________ 24
11. Appendices__________________________________________________ 25
11.1. Listofshortcutkeys __________________________________________________25
11.2. Listoficonsandtheirfunction _________________________________________ 26
11.3. ProblemsandSolutions_______________________________________________ 26
12. ConnectionConfigurationwithterminal__________________________ 27
12.1. WithWindows2000Professional________________________________________27
12.2.WithWindows2003Serveur___________________________________________ 40
12.3.
WithWindowsXPProfessional______________________________________ 55
12.4.
WithWindowsVistaProfessional____________________________________ 65
12.5.
WithWindowsSevenProfessional___________________________________ 79
900001549R1100001_2961074105/96
Copyright2009Ingenico
Allrightsreserved
1. INTRODUCTION
This document describes the manner in which to install and use the Local Loading Tool (LLT). This tool
allowstheusertodownloadapplicationsintheterminalswithTELIUMtechnology.
Inthecontinuationofthisdocument,thefollowingdesignations:
terminalswithTELIUMtechnology
willbereplacedindifferentlyby:
thewordterminalortheabbreviationEFT.
ToinstallandusetheLLTsoftwarefollowthedifferentstepsdescribedbelow:
Softwareinstallation
ConnectionConfigurationwithterminalaccordingtotheusedWindowsplatform.
UseofLLTfunctions
2. Environment
LLTsoftwarerunsunderMicrosoftWindowsplatform:
Windows2000ProfessionalServicePack2Minimum.
Windows2003Server
WindowsXP
WindowsVistaProfessional
WindowsSevenProfessional
InorderforthesoftwaretorunthecomputerwherethesoftwareisinstalledmusthaveaCDROMdrive
andaserialorUSBport.
3. Softwareinstallation
You must have administrative privileges to install and to uninstall this program. This includes having
administrativeprivilegesthefirsttimeyoustartyourcomputerafterinstallingoruninstalling.
LLT use port IP 6000 for data exchange. The use of this port must not be forbidden by the network
administration(Firewall,VirtualPrivateNetwork(VPN))ormustnotbeusedbyanotherapplication.
BeforeinstallingtheLLTapplication,makesurethatallapplicationsareclosed.
Then,inserttheCDROMcontainingtheLLTsoftwareandfollowinstructionsoftheLLTsetup.
If your PC doesn't run the setup automatically, click "Start" button from the task bar, choose "Run ...",
then "Browse ..." CD drive and select "LLT_setup.exe". Launch setup after clicking on the "Open" and
"OK"Button.
Onceyouhavecompletedthesetupprocedure,youcanlaunchthetoolbydoubleclickingontheLLTicon
orfromStartbutton,
choosePrograms>TELIUMTools>LLT>LLT.
900001549R1100001_2961074106/96
Copyright2009Ingenico
Allrightsreserved
4. Softwareremoval
FromtaskbarclickStartandchoosePrograms>TELIUMTools>LLT>UninstallLLT.
5. UseofLLTfunctions
LLT allows downloading software components or parameter files in the terminal during a downloading
activity.Italsomayallowuploadingdiagnosticfileduringadiagnosticormaintenanceactivity.
5.1.
Softwarecomponentdownloading
SelectthedownloadingactivityintheLLTmenu.ActivityDownloading
Connecttotheterminal(seeConnectingtotheterminal)
MoveintheLLTexplorerinordertoselectthecatalogfilescorrespondingtothecomponentsto
bedownloaded(seeFileselection).
Downloadthecomponent(s)intheSWAPdirectoryoftheterminal(seeFiletransfer).
Disconnect(seeDisconnectingtotheterminal).Thevalidcomponentsaretransferredinthe
SYSTEMdirectoryinordertobeused
5.2. Parameterfilesdownloading
YoucandownloadaparameterfileusablebyanapplicationintheHOSTdirectoryoftheterminal.
Note:theapplicationusingthisparameterfilewillhavetodeleteitafterusing.
SelectthedownloadingactivityintheLLTmenu.ActivityDownloading
Connecttotheterminal(seeConnectingtotheterminal)
iconorwithCTRL+Bkeys.
GotoHOSTdirectorybyclicking
MoveintheLLTexplorerinordertoselectthefilestobedownloaded(seeFileselection).
Downloadthecomponent(s)intheHOSTdirectoryoftheterminal(seeFiletransfer).
Disconnect(seeConnectingtotheterminal).
900001549R1100001_2961074107/96
Copyright2009Ingenico
Allrightsreserved
5.3. Knowingthepresentcomponentlistintheterminal
SelectthedownloadingactivityintheLLTmenu.ActivityDownloading
Connecttotheterminal(seeDisconnectingtotheterminal)
DoubleclickonRUNNING.LSTorViathemenu"Terminal"|"componentlist"orCTRL+Fkeysto
displaythecomponentlist.
5.4. Uploadingdiagnosticfiles
SelectthedownloadingactivityintheLLTmenu.ActivityDiagnostic
Connecttotheterminal(seeConnectingtotheterminal)
Selectthediagnosticfilesintheterminalviewtobeuploaded(seeFileselection).
Transferthefile(s)inaPCdirectory(seeFiletransfer).
Disconnect(seeDisconnectingtotheterminal).
Displaycontentofdiagnosticfiles(seeFileLIFECOUNTER.DIA,FileBOOSTERDIA,File
APPDEFAULT.DIAorFileAPPCOUNTER.DIA)
5.5. Connectingtotheterminal
Beforethefirstconnection,
CheckConnectionConfigurationwithterminalinfunctionofplatformMicrosoftWindowsused.
makesuretheserialportcableortheUSBcableiscorrectlyconnectedtothePCandterminal.
CheckTerminalisreadytobeconnectedwithLLT.TheterminalmustdisplayLLT.
Differentwaysofconnecting:
o
o
o
withmouse:byclickingontheicon
viathemenu:"Terminal"|"connection"
withkeyboard:F4key
900001549R1100001_2961074108/96
Copyright2009Ingenico
Allrightsreserved
Graphicmode:
1. IfOptionUSBEnumison(yes)(seeFileLLT.INT)
PriorityisgiventoUSBlink.
IfmorethenoneterminalareconnectedwithUSBlinks,alistoflinksisproposed.
IfnoterminalconnectedwithUSBlinks,theconnectionismadewiththeportselectedinthe
Connexion|Configurationconnexiondialog.
2. IfOptionUSBEnumisoff(no)
TheconnectionismadewiththeportselectedintheConnexion|Configurationconnexion
dialog.
Commandemode(voirCommandmode):
1. IfOptionUSBEnumison(yes)(seeFileLLT.INT)
PriorityisgiventoUSBlink.
IfoneterminalconnectedwithUSBlinks,theconnectionismadewiththisport.
If more than one or no terminal connected with USB links, the connection is made with the
portspecifiedinthecommandline
(xnumberofport)or(ifomitted)thelastportusedbyLLT.
2. IfOptionUSBEnumisoff(no)
Theconnectionismadewiththeportspecifiedinthecommandline
(xnumberofport)or(ifomitted)thelastportusedbyLLT.
5.6. Disconnectingtotheterminal
TheterminalwillonlyactivatetransferredfilesonceLLTisdisconnectedfromtheterminal.
Differentwaysofdisconnecting:
Withmouse:byclickingontheicon
Viathemenu:"Terminal"|"disconnection"
Withkeyboard:CTRL+F4keys
5.7. Selectionandfiletransfer
5.7.1.
Fileselection
The selection of .Mxx (Mxx corresponding to the catalog file extension ) allows the user to view only
catalogfilesoftheselection.Insuchmode,ifacatalogfiletransferiscarriedout,allfilespresentinthat
filewillbetransferred,exceptedthecatalogfiles(*.Mxxextension).
associated to the file list, allows the user to view all files and sub
Selecting *.* in the list
directoriesfromthecurrentdirectory.Inthismodeallselectedfileswillbetransferred.
5.7.1.1. Selectingafile
withmouse:clickingonthefile
withkeyboard:NavigatingwithUpandDownkeysonceviewisselected(seeSelectingaLLTview)
900001549R1100001_2961074109/96
Copyright2009Ingenico
Allrightsreserved
5.7.1.2. Selectingagroupofcontiguousfiles
withmouse:selectionismadeinthesamewayasWindowsExplorer
withkeyboard:selectionismadeinthesamewayasWindowsExplorer
5.7.1.3. Selectingagroupofnoncontiguousfiles
withmouse:selectionismadeinthesamewayasWindowsExplorer.
withkeyboard:notsupported.
5.7.1.4. Selectingallthefiles
withkeyboard:onceviewisselected(seeSelectingaLLTview),presssimultaneouslyCtrlandAkeys.
5.7.1.5. Unselectingallthefiles
withmouse:clickingonafreespaceintheview.
5.7.2.
Filetransfer
Onceconnectionhasbeenestablished.(SeeConnectingtotheterminal)andoncefileshavebeenselected
(seeFileselection).
Viathemenu"Terminal"|"filedownloading"or"Terminal"|"fileuploading"
Withmouse:draganddropinthecorrespondingwindow.
Withkeyboard:F2ouCTRL+F2keys
Bydefaulttheremotedownloadingactivityisselected.Maintenanceanddiagnosticsactivitiesare
alsopossiblefromLLTbyselectingthemenu"Activity".
5.7.3.
CopyFileList
Youcancopythelistofselectedfilefromthecurrentviewtotheclipboardwiththepopupmenu
orwiththeCTRL+Ckeys.
900001549R1100001_29610741010/96
Copyright2009Ingenico
Allrightsreserved
5.8. Displayingandconsultation
5.8.1.
Directaccesstoadirectoryofthecomputer
Selectthedirectoryinthelistofthefavouritedirectories.
Toaddapathinthelistselectadirectoryinthetreeviewthen
UseSHIFT+Inskeys
Orusethepopupmenu(withtherightbuttonofthemouse).
Todeleteapathinthelist,selectthedirectorynameinthetreeviewthen
UseSHIFT+DELkeys
Orusethepopupmenu(withtherightbuttonofthemouse).
WhentheLLTapplicationisclosed,thecurrentdirectoryisstoredinthelistofthefavouritedirectories.At
thenextLLTexecution,thisdirectorywillbethecurrentdirectory.
5.8.2.
Directaccesstoadirectoryofthecomputer
FromPCViewuseCTRLJkeystogotoTerminalvieworclickontheTerminalview.
FromTerminalViewuseCTRLKkeystogotoPCvieworclickonthePCview.
5.8.3.
Directaccesstoadirectoryofthecomputer
AdoubleclickonthefileitselforpressReturnkeyafterselectingthefiledisplaysinawindowthefile
contentsintextmode.
900001549R1100001_29610741011/96
Copyright2009Ingenico
Allrightsreserved
5.8.4.
Componentsignatureconsultation
Select*.*inthelist
thenDoubleclickonthe*GNcorrespondingtoasignedcomponentto
consult(OptionCertif_SGNon).
5.8.5.
Componentsignatureconsultation
Once connection has been established, terminal characteristics can be consulted Via the menu
"Terminal"|"Information"orbyclickingonicon
orwithCTRL+Ikeys.
900001549R1100001_29610741012/96
Copyright2009Ingenico
Allrightsreserved
900001549R1100001_29610741013/96
Copyright2009Ingenico
Allrightsreserved
5.9. Displayingandconsultation
5.9.1.
Consultingcatalogfile
Thecatalogdescription
isdisplayedeachtimeacatalogfileisselected.
ContextualmenuorF9keyafterselectingafile.allowstheusertoviewthecatalogfilecontentsandalso
viewingtheassociateddescriptorfileandthesignedfile(seeComponentsignatureconsultation)contents
byselectingitinthefilelist.
900001549R1100001_29610741014/96
Copyright2009Ingenico
Allrightsreserved
5.9.2.
Consultingcatalogfile
UsecontextualmenuorF7keyafterselectingfiles.Thisallowstheusertocreatecatalogfilesforanother
producttypefromanexistingone.
5.9.3.
Consultingcatalogfile
Thisfunctionallowstheusertocreateacatalogfilelisttodownload.Thisfunctionisonlyaccessibleafter
selectingthe*.Mxx(Mxxcorrespondingtothecatalogfileextension)inthelistassociatedtothefilelist.
Selectingthecatalogfilestoincludethenusethecontextualmenu
900001549R1100001_29610741015/96
Copyright2009Ingenico
Allrightsreserved
orF8keytocreateanewcatalogfilegroupingseveralcatalogfilesforasameterminalstoredinthesame
directory.
5.9.4.
Deletionofacatalogfile
When you delete a catalog file, the software deletes associated files, only if they are not used by other
files.
900001549R1100001_29610741016/96
Copyright2009Ingenico
Allrightsreserved
6. FileLIFECOUNTER.DIA
6.1. FileLIFECOUNTER.DIA
ForviewaLifeCounter.diafile,youmustdoubleclickonthefile,andaftertheinformationofthisfileare
decodedinawindow.
7. FileBOOSTERDIA
7.1.
ConsultingofBoosterdiafiles:
For view a Booster.dia file, you must doubleclick on the file, and after the information of this file are
decodedinawindow.
900001549R1100001_29610741017/96
Copyright2009Ingenico
Allrightsreserved
8. FileAPPDEFAULT.DIA
8.1. ConsultationofAppDefault.dia.files:
ForviewaAppDefault.diafile,youmustdoubleclickonthefile,andaftertheinformationofthisfileare
decodedinawindow.
9. FileAPPCOUNTER.DIA
9.1. ConsultationofAppCounter.dia.files:
ForviewaAppCounter.diafile,youmustdoubleclickonthefile,andaftertheinformationofthisfileare
decodedinawindow.
900001549R1100001_29610741018/96
Copyright2009Ingenico
Allrightsreserved
10. LLTSetting
10.1. FileLLT.INT
ItconfiguresLLT.
Optionslist(yes/no):
RemoteDirectory(yesdefaultvalue):displayingnetworkdisks.
Certif_SGN(nodefaultvalue):displayingcertificateof*.?GNfiles.
Auto_bmk(nodefaultvalue):automaticstorageoflastdirectoryused
(inbmkfile).
EnumUSB(yesdefaultvalue):automaticenumerationofterminals
connectedtoPCusinganUSBlink.
Example:
;LLTconfiguration
;
[Protocol]
ConnectionName=LLTConnection
;nameofconnectiondefinedvia
;remotenetwork
[Files]
Language=LLT.lng
;nameoflanguagefiletobeused
CataExt=LLT.prm
;namelistofcatalogfileextensions
Bookmark=LLT.bmk
;listofthefavouritedirectories
[Options]
RemoteDirectory=no ;nodisplayingnetworkdisksintheLLTexplorer
Certif_SGN=yes;displayingcertificateof*GNfiles
900001549R1100001_29610741019/96
Copyright2009Ingenico
Allrightsreserved
10.2. FileLLT.PRM
ItallowstheusertodefineproductcodelistdefinedforEFTandtheassociatedterminaldescription.
Thisproductcodecorrespondstocatalogfilesextension.
Syntax:
Mxy:productdescription
Example:
M30:stationary
M31:portable
10.3. FileLLT.LNG
It contains the list of messages to be displayed by LLT. These messages are written in 2 different
languages:thelocallanguage(Englishbydefault)andFrench.
10.4. FileLLT.BMK
ItcontainsthelistofthefavouritedirectoriesthattheusercanaccessinoneclickfromLLT.Theusercan
writethedirectoriestobeaccessedeasilyinit.
10.5. ChangingLLTlanguage
Atfirststartup,LLTscreensaredisplayedinEnglish.
ThelanguagemaybemodifiedviatheMenu"Language"orfunctionkeysCTRL+EorCTRL+L.
Atnextstartup,LLTscreenswillbedisplayedinthelastselectedlanguage.
10.6. Defininganewtranslationlanguage
Alanguagefile(filewithextension.lng)isusedtotranslatethedifferentscreens,menus,andmessagesof
thetool.
Bydefaultthisfilecontains2languages(EnglishandFrench).
Nevertheless,anylanguagecanbeused.Tousethelocallanguage,replaceinthelanguagefiletheFrench
translationbythelocaltranslation.
900001549R1100001_29610741020/96
Copyright2009Ingenico
Allrightsreserved
10.7. LLTuseincommandmode
10.7.1. Actions
c=downloadingthefileslistedincatalogfile
u=uploadingthefileslistedincatalogfile
d=deletingthefileslistedincatalogfile
10.7.2. Switches
r=filenamewhereisstoredtheresultingcode(ifomitted,returncodewillbestoredinResBatch.txtin
theLLTinstallationdirectory
e = name of the directory in the terminal where are downloaded the files contained in catalog file
(downloadingmode)orfromwhereareuploadedthefilescontainedincatalogfile(uploadingmode)or
wherearedeletedthefilescontainedincatalogfile(deletingmode)(ifomitted,swapdisk)
a=numberofactivity(ifomitted,1)(1=downloading,2=diagnostic,3=maintenance)
x=numberofserialport(ifomitted,lastportusedbyLLT)
n=withoutdialogboxdisplayed
10.7.3. Syntax
Downloading:
LLT.EXE c<path and catalog file name> r<path and result file name> a<N of activity> e<name of the
directoryinterminalwherearedownloadedthefiles>x<Nofserialport>
Uploading:
LLT.EXE u<path and catalog file name> r<path and result file name> a<N of activity> e<name of the
directoryinterminalfromwhereareuploadedthefiles>x<Nofserialport>
Deleting:
LLT.EXE d<path and catalog file name> r<path and result file name> a<N of activity> e<name of the
directoryinterminalwherearedeletedthefiles>x<Nofserialport>
900001549R1100001_29610741021/96
Copyright2009Ingenico
Allrightsreserved
10.7.4. Returncodes
ThedownloadingreturncodeisnumericalASCIIcodedintheresultingfilefollowedbyatext.
"0":OK
"1":missingparameter
"2":catalogfileaccessproblem
"3":resultingfileaccessproblem
"4":downloadablefilesaccessproblem
"5":LLTalreadyrunning
"6":LLTconfiguringfilemissing(LLT.INI,LLT.LNG,LLT.PRM)
"7":connectionname("LLTConnection")notfoundinWindowsRAS.
"8":PPPconnectionproblem(RASerror+errornumber)
"9":FTPconnectionproblem
"10":FTPerrorduringfiletransfer
"11":terminalnotrespondingoncePPPconnectionhasbeenestablished
"12":LLTcannotberunonsuchWindowsplatform
"13":LLTidentificationnotrecognizedbytheterminal
"14":unauthorizedactivity
"15":activitybadlyfinished
"17":cannotdownloadafileadiagnosticactivity
"18":cannotfoundtheRASphonebook
"19":COMportunknown
900001549R1100001_29610741022/96
Copyright2009Ingenico
Allrightsreserved
10.7.5. Returncodes
Catalogfilename:31140210.M30
Withvalues:;DownloadfilestoSWAP
31140210.ADF
31140210.SGN
;Changedestinationdirectoryanddownloadafile
eHOST
Param.txt
Commandefile:LoadingTest.bat
Withvalues:
@echooff
setPATH=C:\ProgramFiles\TELIUMTools\LLT
setNB=1
set/PPORT=EnterCOMportnumberor[ENTER]forCOM%NB%:
if.%PORT%.==..gotoLabel0
setNB=%PORT%
:Label0
echoEnterLLTToolsinstalldirectoryor[ENTER]for
set/pLLT_TOOLS="%PATH%":
if.%LLT_TOOLS%.==..gotoLabel1
setPATH=%LLT_TOOLS%
:Label1
setLLT="%PATH%\LLT.EXE"
echoLaunchLLTToolsontheterminal
set/pT=When"LLT"displayed,pressakeytocontinue...
echoCatalogueloadinginprogress...
%LLT%c31140210.M30eSWAPa1x%NB%
echoLoadingisfinished.
set/pT=Pressakeytocontinue...
900001549R1100001_29610741023/96
Copyright2009Ingenico
Allrightsreserved
10.8. DisplayingtheUSBconnectionportnumber
LaunchtheDevicemanagerpanelviathemenuConnection|DevicemanagerofLLT.
900001549R1100001_29610741024/96
Copyright2009Ingenico
Allrightsreserved
11. Appendices
11.1. Listofshortcutkeys
Each LLT function is accessible via the menu and is also accessible via a keyboard function key or a
combinationofthesekeys.Thistoolcanbeusedwithoutamouse,eachmenufunctionisalsoaccessibleby
pressingALT+menuletter.Oncethemenuisopened,accesstosubmenusisavailableviathekeyboard
bypressingSHIFT+letterofsubmenu.
Function
Connecttoterminal
Disconnectfromterminal
Filesdownloading
Filesuploading
Refreshtheviewcontents
Creatingacatalogfilefromanexistingone
Creatingafamily
Consultacatalogfile
Changealanguage
Openafileoradirectory
Deletesomefilesfromtheview
Selectthefavouritedirectorylist
Addadirectorytothefavouritedirectorylist
Deleteadirectoryfromthefavouritedirectorylist
Selectallthefiles
Gobacktotheparentdirectory
Copyfilelistfromtheviewtoclipboard
Displaythelistofmodulespresentintheterminal
TerminalInformation
Terminalviewisactiveview
PCviewisactiveview
ExitfromLLT
Short Cut
F4
CTRL+F4
F2
CTRL+F2
F5
F7
F8
F9
CTRL+E(English)
CTRL+L(Locallanguage)
Returnkey
Delkey
SHIFT+F
SHIFT+Ins
SHIFT+Del
CTRL+A
CTRL+B
CTRL+C
CTRL+F
CTRL+I
CTRL+J
CTRL+K
CTRL+Q
900001549R1100001_29610741025/96
Copyright2009Ingenico
Allrightsreserved
11.2. Listoficonsandtheirfunction
Foreachviewaniconbarallowstheusertoaccesstosomefunctions.
icon or Del key or popup menu to delete selected file(s) from the current view and from the
Use
correspondingdirectory (Note:Suchfunctioncanbeunauthorisedontheterminal).When youdelete a
catalogfile,thesoftwaredeleteassociatedfiles,onlyiftheyarenotusedbyotherfiles.
Use
iconorF5keyrefreshviewcontents.
permetdevisualiserdansl'ordrelesfichiersdelavuesouslaformede:grandesicnes,
petitesicnes,liste,oudtails.
Use
iconorCTRL+Bkeynavigateandviewtheparentdirectory.
11.3. ProblemsandSolutions
Someerrorsareclassifiedbycode,theirdescriptionisgivenbelowinordertocheckpotentialproblems.
Errornumber error
Whattodo?
Ras602
Theportisalreadyopen.
The serial port used by LLT is already used by another
application.
Ras624
RasPhone2000.pbk
FirstlocatetheRasphone2000.pbkfile(filelocatedintheRAS
subdirectoryoftheLLTdirectoryapplication)andmakesure
thatthereadonlyfilepropertyinthePropertiesdialogboxis
notselected.
Ras629
Theportwasdisconnected Check that hardware flow control hardware is still activated
bytheremotemachine.
onLLTorcheckthatterminaliswaitingforconnection.
Ras633
The remote computer is in CheckUSBportispresentinthelistofmodemorcheckifthe
used
USBcableisconnectedtotheUSBportdeclaredonPC.
Ras721
The remote computer did ThepluggedportCOMxisnotselected.SeechapterSelecting
communicationportorseechapterInstallingthenullmodem
notrespond.
drivertodefinetheusedserialinterface.
Ras651orRas Yourconnectingdevicehas Terminalisnotresponding.Checkconnection(checktheserial
777
reportedanerror.
cable or USB cable is correctly plugged) and check that
terminal is waiting for a connection. If not check Selecting
communicationportorInstallingthenullmodemdriver.
FTP12002
Internetconnected
StoptheWificonnectiononthePC.
FTP12163
Internetdisconnected
InwebbrowserdeletecheckfromtheProperty"workingoff
line"
LLT
displays
PPP LLTusesportIP6000fordataexchange.Checkthattheuse
Connected
then of this port is not forbidden by the network administration
automatically
(Firewall, Virtual Private Network (VPN)) or check the port is
disconnecting
notusedbyanotherapplication.
900001549R1100001_29610741026/96
Copyright2009Ingenico
Allrightsreserved
12. ConnectionConfigurationwithterminal
ConnectionconfigurationisdifferentfollowingtheMicrosoftWindowsplatformused.
12.1. WithWindows2000Professional
12.1.1.
Connectionwithserialinterface
To be connected to a terminal a serial cable must be used. Configure the PC by selecting a null modem
driverandselecttheserialportthatwillbeusedwiththisconnection.
12.1.1.1. Installingthenullmodemdriver
Configuretheserialinterfaceviathemenu.Connection|SerialinterfacepropertiesofLLT.
If no modem has been installed on this computer, the following screen appears:
900001549R1100001_29610741027/96
Copyright2009Ingenico
Allrightsreserved
Keyinanyvalueforyourareacode,thenclosethewindowbybuttonOK.
Click"Add"buttontoinstallthenullmodemdriver.
Then,
900001549R1100001_29610741028/96
Copyright2009Ingenico
Allrightsreserved
Checktheoption "Don't detect my modem; I will select it from a list " and then click "Next" buttonto
selectthenullmodemdriverfromalist.
Inthatcaseselect(StandardsModemTypes)fromthelistManufacturersandCommunicationscable
betweentwocomputersfromthelist"Models".
Thenclick"Next"buttontoselecttheserialportthatwillbeusedfortheconnection.
900001549R1100001_29610741029/96
Copyright2009Ingenico
Allrightsreserved
SelectaspecificportorAllportsifyouwanttobeabletouseeitheroneortheother.
Continuebyclicking"Next"button
Thenclick"Finish".
Thenewinterfaceappearsnowfromthelist.
900001549R1100001_29610741030/96
Copyright2009Ingenico
Allrightsreserved
Click"Properties"buttontoconfiguretheserialinterface.
In"General"tab,
SelecttheMaximumPortSpeed:115200.
ClickOKofthedifferentwindowsthathavebeenopenedtovalidatealltheseparametersandterminate
thisconfiguration.
900001549R1100001_29610741031/96
Copyright2009Ingenico
Allrightsreserved
12.1.1.2.Useofanotherserialport
ItispossibletodefineseveralserialportsinordertoselectlatertheavailableportduringstepSelecting
communicationport.Todefineanewinterfaceandanewserialport(forexampleusingCOM2),repeat
forthenewportthestepsdescribedinInstallingthenullmodemdriver.
12.1.1.3. Selectingcommunicationport
SelecttheserialportusedfromConnection|ConnectionconfigurationofLLTmenu.
Selecttheporttousefromdevicelist
If the serial port is not displayed in the device list, check if it has correctly been defined (see chapter
Installingthenullmodemdriver).
12.1.1.4. Communicationportconfiguration
UsedcommunicationportconfigurationismadefromLLTmenuConnection|Connectionconfiguration
900001549R1100001_29610741032/96
Copyright2009Ingenico
Allrightsreserved
ClickConfigure
Thenchooseinitialspeed:115200andenablehardwareflowcontrol.
900001549R1100001_29610741033/96
Copyright2009Ingenico
Allrightsreserved
Click
OKinthedifferentopenedwindowstovalidthesesettings.
12.1.2. ConnectionwithUSBcable
TobeconnectedtoaterminalaUSBcablemaybeusediftheterminalsoftwareconfigurationauthorizes
it.
12.1.2.1.TeliumUSBdriverinstallation
PuttheterminalinLLTmode(terminalmustdisplayLLT).
ConnectUSBcablebetweenterminal(USBSlave)andPC(USBHost).
WhenyouplugtheterminalwithUSBcable,Windows2000detectsthenewdevice.
ThensuggestinstallinganewdriverinordertomanageUSBterminalconnection.
900001549R1100001_29610741034/96
Copyright2009Ingenico
Allrightsreserved
Click"Next"
Click"Next"toselectUSBdriverforconnectedTerminal.
900001549R1100001_29610741035/96
Copyright2009Ingenico
Allrightsreserved
Click"Next"andgivethedirectoryofLLTapplication
andconfirmbyOK.
Ifthedriverhasbeenfound,thefollowingscreenisdisplayed:
900001549R1100001_29610741036/96
Copyright2009Ingenico
Allrightsreserved
Click"Next"
900001549R1100001_29610741037/96
Copyright2009Ingenico
Allrightsreserved
Then"Finish".Now,theUSBdriverisinstalledandreadytobeused.TheUSBconnectionisseenbyLLTas
aserialport.Youmustconfigurethisnewport(SeeInstallingthenullmodemdriver).Choosethenew
portwhichisdisplayedinthelistcorrespondingtotheestablishedUSBconnection.
Now,thenewcommunicationcableappearsfromthelist.
900001549R1100001_29610741038/96
Copyright2009Ingenico
Allrightsreserved
ClickOK.
SelecttheserialportusedfromConnection|ConnectionconfigurationofLLTmenu.
Selecttheporttousefromdevicelist
900001549R1100001_29610741039/96
Copyright2009Ingenico
Allrightsreserved
andclickOK.Now,yourconnectionisconfigured.YoucanconnecttheLLTtotheterminal(seeConnecting
totheterminal).
12.2. WithWindows2003Serveur
12.2.1. Connectionwithserialinterface
To be connected to a terminal a serial cable must be used. Configure the PC by selecting a null modem
driverandselecttheserialportthatwillbeusedwiththisconnection.
900001549R1100001_29610741040/96
Copyright2009Ingenico
Allrightsreserved
12.2.1.1.Installingthenullmodemdriver
Configuretheserialinterfaceviathemenu.Connection|SerialinterfacepropertiesofLLT.
Ifnomodemhasbeeninstalledonthiscomputer,thefollowingscreenappears:
Click"Add"buttontoinstallthenullmodemdriver.
Then,
900001549R1100001_29610741041/96
Copyright2009Ingenico
Allrightsreserved
Checktheoption "Don't detect my modem; I will select it from a list " and then click "Next" button to
selectthenullmodemdriverfromalist.
Inthatcaseselect(StandardsModemTypes)fromthelistManufacturersandCommunicationscable
betweentwocomputersfromthelist"Models".
Thenclick"Next"buttontoselecttheserialportthatwillbeusedfortheconnection.
900001549R1100001_29610741042/96
Copyright2009Ingenico
Allrightsreserved
SelectaspecificportorAllportsifyouwanttobeabletouseeitheroneortheother.
Continuebyclicking"Next"button
900001549R1100001_29610741043/96
Copyright2009Ingenico
Allrightsreserved
Thenclick"Finish".
Thenewinterfaceappearsnowfromthelist.
Click"Properties"buttontoconfiguretheserialinterface.
In"Modem"tab,
selecttheMaximumPortSpeed:115200.
ClickOKofthedifferentwindowsthathavebeenopenedtovalidatealltheseparametersandterminate
thisconfiguration.
12.2.1.2. Useofanotherserialport
ItispossibletodefineseveralserialportsinordertoselectlatertheavailableportduringstepSelecting
communicationport.Todefineanewinterfaceandanewserialport(forexampleusingCOM2),repeat
forthenewportthestepsdescribedinInstallingthenullmodemdriver.
12.2.1.3.
Selectingcommunicationport
SelecttheserialportusedfromConnection|ConnectionconfigurationofLLTmenu.Selecttheportto
usefromdevicelist
900001549R1100001_29610741044/96
Copyright2009Ingenico
Allrightsreserved
If the serial port is not displayed in the device list, check if it has correctly been defined (see chapter
Installingthenullmodemdriver).
900001549R1100001_29610741045/96
Copyright2009Ingenico
Allrightsreserved
12.2.1.4.
Communicationportconfiguration
UsedcommunicationportconfigurationismadefromLLTmenuConnection|Connectionconfiguration
ClickConfigure
900001549R1100001_29610741046/96
Copyright2009Ingenico
Allrightsreserved
Thenchooseinitialspeed:115200andenablehardwareflowcontrol.
Click
OKinthedifferentopenedwindowstovalidthesesettings.
12.2.2. ConnectionwithUSBcable
TobeconnectedtoaterminalaUSBcablemaybeusediftheterminalsoftwareconfigurationauthorizes
it.
12.2.2.1. USBTeliumdriverInstallation
PuttheterminalinLLTmode(terminalmustdisplayLLT).
ConnectUSBcablebetweenterminal(USBSlave)andPC(USBHost).
WhenyouplugtheterminalwithUSBcable,Windows2000detectsthenewdevice.
ThensuggestinstallinganewdriverinordertomanageEFT30USBterminalconnection
900001549R1100001_29610741047/96
Copyright2009Ingenico
Allrightsreserved
Click"Next"
900001549R1100001_29610741048/96
Copyright2009Ingenico
Allrightsreserved
Click"Next"andgivethedirectoryofLLTapplication
900001549R1100001_29610741049/96
Copyright2009Ingenico
Allrightsreserved
Click"Next".
Ifthefilehasbeenfound,thefollowingscreenisdisplayed:
900001549R1100001_29610741050/96
Copyright2009Ingenico
Allrightsreserved
Click"Next".
Then"Finish".Now,theUSBdriverisinstalledandreadytobeused.TheUSBconnectionisseenbyLLTas
aserialport.Youmustconfigurethisnewport
900001549R1100001_29610741051/96
Copyright2009Ingenico
Allrightsreserved
(SeeInstallingthenullmodemdriver).Choosethenewportwhichisdisplayedinthelistcorrespondingto
theestablishedUSBconnection.
Now,thenewcommunicationcableappearsfromthelist.
900001549R1100001_29610741052/96
Copyright2009Ingenico
Allrightsreserved
ClickOK.
SelecttheserialportusedfromConnection|ConnectionconfigurationofLLTmenu.
Selecttheporttousefromdevicelist
900001549R1100001_29610741053/96
Copyright2009Ingenico
Allrightsreserved
andclickOK.Now,yourconnectionisconfigured.YoucanconnecttheLLTtotheterminal(see
Connectingtotheterminal).
900001549R1100001_29610741054/96
Copyright2009Ingenico
Allrightsreserved
12.3. WithWindowsXPProfessional
12.3.1. Connectionwithserialinterface
Tobeconnectedtoaterminalaserialcablemustbeused.ForthatconfigurethePCbyselectinganull
modemdriveranddeterminetheserialportthatwillbeusedwiththisconnection.
12.3.1.1. Installingthenullmodemdriver
Configuretheserialinterfaceviathemenu.Connection|SerialinterfacepropertiesofLLT.
Ifnomodemhasbeeninstalledonthiscomputer,thefollowingscreenappears:
Keyinanyvalueforyourareacode,thenclosethewindowbybuttonOK.
900001549R1100001_29610741055/96
Copyright2009Ingenico
Allrightsreserved
Click"Add"buttontoinstallthenullmodemdriver.
Then,
900001549R1100001_29610741056/96
Copyright2009Ingenico
Allrightsreserved
Checktheoption"Don'tdetectmymodem;I willselectitfromalist"andthenclick"Next"buttonto
selectthenullmodemdriverfromalist.
900001549R1100001_29610741057/96
Copyright2009Ingenico
Allrightsreserved
Inthatcaseselect(StandardsModemTypes)fromthelistManufacturersandCommunicationscable
betweentwocomputersfromthelist"Models".
Thenclick"Next"buttontoselecttheserialportthatwillbeusedfortheconnection.
900001549R1100001_29610741058/96
Copyright2009Ingenico
Allrightsreserved
SelectaspecificportorAllportsifyouwanttobeabletouseeitheroneortheother.
Continuebyclicking"Next"button
thenclick"Finish".
Thenewinterfaceappearsnowfromthelist.
900001549R1100001_29610741059/96
Copyright2009Ingenico
Allrightsreserved
Click"OK"tovalidatethesesettings.
12.3.1.2.
Useofanotherserialport
Itispossibletodefineseveralserialportsinordertoselectlatertheavailableport(SeechapterSelecting
communicationport).Todefineanewinterfaceandanewserialport(forexampleusingCOM2),repeat
thepreviousstepdescribedinInstallingthenullmodemdriver
12.3.1.3. Selectingcommunicationport
SelecttheserialportusedfromConnection|ConnectionconfigurationLLTmenu.
Selecttheporttouseinthedevicelist.
Iftheserialportisnotdisplayedinthedevicelist,checkifithascorrectlydefined(seechapterInstalling
thenullmodemdriver).
BeforeusingLLTapplicationcheckthatLLTcableiscorrectlypluggedintotherightserialconnector.
900001549R1100001_29610741060/96
Copyright2009Ingenico
Allrightsreserved
12.3.1.4. Communicationportconfiguration
UsedcommunicationportconfigurationismadefromLLTmenuConnection|Connectionconfiguration
ClickConfigure
Thenchooseinitialspeed:115200andenablehardwareflowcontrol.
900001549R1100001_29610741061/96
Copyright2009Ingenico
Allrightsreserved
Click
OKinthedifferentopenedwindowstovalidthesesettings.
12.3.2. ConnectionwithUSBcable
Tobeconnectedtoaterminal,anUSBcablemaybeusediftheterminalsoftwareconfigurationauthorizes
it.
12.3.2.1.
TeliumUSBdriverInstallation
PuttheterminalinLLTmode(terminalmustdisplayLLT).
ConnectUSBcablebetweenterminal(USBSlave)andPC(USBHost).
WhenyouplugtheterminalwithUSBcable,WindowsXPsuggeststoinstallanewdriverinorderto
manageUSBterminalconnection.
Click"Next"
900001549R1100001_29610741062/96
Copyright2009Ingenico
Allrightsreserved
ClickBrowsetoselectthedriverssubdirectorylocatedintheLLTinstallationdirectory.Thenclick
Next.
Then"Finish".Now,theUSBdriverisinstalledandreadytobeused.TheUSBconnectionisseenbyLLTas
aserialport.Youmustconfigurethisnewport(Installingthenullmodemdriver).Choosethenewport
whichisdisplayedinthelistcorrespondingtotheestablishedUSBconnection.
900001549R1100001_29610741063/96
Copyright2009Ingenico
Allrightsreserved
Now,thenewcommunicationcableappearsfromthelist.
ClickOK.
900001549R1100001_29610741064/96
Copyright2009Ingenico
Allrightsreserved
SelecttheserialportusedfromConnection|ConnectionconfigurationofLLTmenu.
Selecttheporttousefromdevicelist
andclickOK.Now,yourconnectionisconfigured.YoucanconnecttheLLTtotheterminal(seeConnecting
totheterminal).
12.4. WithWindowsVistaProfessional
12.4.1. Connectionwithserialinterface
Tobeconnectedtoaterminalaserialcablemustbeused.ForthatconfigurethePCbyselectinganull
modemdriveranddeterminetheserialportthatwillbeusedwiththisconnection.
12.4.1.1.
Installingthenullmodemdriver
Configuretheserialinterfaceviathemenu.Connection|SerialinterfacepropertiesofLLT.
Ifnomodemhasbeeninstalledonthiscomputer,thefollowingscreenappears:
900001549R1100001_29610741065/96
Copyright2009Ingenico
Allrightsreserved
Click"Add"buttontoinstallthenullmodemdriver.Then,
Check the option "Don't detect my modem; I will select it from a list " and then click "Next" button to
selectthenullmodemdriverfromalist.
900001549R1100001_29610741066/96
Copyright2009Ingenico
Allrightsreserved
Inthatcaseselect(StandardsModemTypes)fromthelistManufacturersandCommunicationscable
betweentwocomputersfromthelist"Models".
Thenclick"Next"buttontoselecttheserialportthatwillbeusedfortheconnection.
SelectaspecificportorAllportsifyouwanttobeabletouseeitheroneortheother.
Continuebyclicking"Next"button
900001549R1100001_29610741067/96
Copyright2009Ingenico
Allrightsreserved
thenclick"Finish".
Thenewinterfaceappearsnowfromthelist.
900001549R1100001_29610741068/96
Copyright2009Ingenico
Allrightsreserved
Click"OK"tovalidatethesesettings.
900001549R1100001_29610741069/96
Copyright2009Ingenico
Allrightsreserved
12.4.1.2. Useofanotherserialport
It is possible to define several serial ports in order to select later the available port (See Selecting
communicationport).Todefineanewinterfaceandanewserialport(forexampleusingCOM2),repeat
thepreviousstepdescribedinInstallingthenullmodemdriver
12.4.1.3. Selectingcommunicationport
SelecttheserialportusedfromConnection|ConnectionconfigurationLLTmenu.
Selecttheporttouseinthedevicelist.
Iftheserialportisnotdisplayedinthedevicelist,checkifithascorrectlydefined(seeInstallingthenull
modemdriver)
BeforeusingLLTapplicationcheckthatLLTcableiscorrectlypluggedintotherightserialconnector.
900001549R1100001_29610741070/96
Copyright2009Ingenico
Allrightsreserved
12.4.1.4.
Communicationportconfiguration
UsedcommunicationportconfigurationismadefromPCmenustart|Parameter|configurationmanager
|Modemsandtelephonieoptions|Modem
SelecttheportandclickProperties
900001549R1100001_29610741071/96
Copyright2009Ingenico
Allrightsreserved
CliquersurUpdateparameters.
900001549R1100001_29610741072/96
Copyright2009Ingenico
Allrightsreserved
SelectModemandchoose,maximalespeedforport:115200.
SelectAdvancedandChangeDefaultPreference,verifyPortspeedandFlowcontrol(None).
ClickOKinthedifferentopenedwindowstovalidthesesettings
WARNING:ThePCmustberestarted.
12.4.2. ConnectionwithUSBcable
Tobeconnectedtoaterminal,anUSBcablemaybeusediftheterminalsoftwareconfigurationauthorizes
it.
12.4.2.1.
TeliumUSBdriverInstallation
PuttheterminalinLLTmode(terminalmustdisplayLLT).
ConnectUSBcablebetweenterminal(USBSlave)andPC(USBHost).
WhenyouplugtheterminalwithUSBcable,WindowsVistasuggeststoinstallanewdriverinorderto
manageUSBterminalconnection
ClickFindandinstallsoftwaredriver(recommended)
900001549R1100001_29610741073/96
Copyright2009Ingenico
Allrightsreserved
ClickDontsearchinline
900001549R1100001_29610741074/96
Copyright2009Ingenico
Allrightsreserved
ClickFindsoftwaredriveronmycomputer
900001549R1100001_29610741075/96
Copyright2009Ingenico
Allrightsreserved
ClickBrowsetoselectthedriverssubdirectorylocatedintheLLTinstallationdirectory.Thenclick
Next.
ClickInstall
900001549R1100001_29610741076/96
Copyright2009Ingenico
Allrightsreserved
Then"Finish".Now,theUSBdriverisinstalledandreadytobeused.TheUSBconnectionisseenbyLLTas
aserialport.Youmustconfigurethisnewport(SeeInstallingthenullmodemdriver).Choosethenew
portwhichisdisplayedinthelistcorrespondingtotheestablishedUSBconnection.
900001549R1100001_29610741077/96
Copyright2009Ingenico
Allrightsreserved
Now,thenewcommunicationcableappearsfromthelist.ClickOK.
SelecttheserialportusedfromConnection|ConnectionconfigurationofLLTmenu.Selecttheportto
usefromdevicelist
900001549R1100001_29610741078/96
Copyright2009Ingenico
Allrightsreserved
andclickOK.Now,yourconnectionisconfigured.YoucanconnecttheLLTtotheterminal(Connectingto
theterminal).
12.5.
WithWindowsSevenProfessional
12.5.1. Connectionwithserialinterface
To be connected to a terminal a serial cable must be used. For that configure the PC by selecting a null
modemdriveranddeterminetheserialportthatwillbeusedwiththisconnection.
12.5.1.1.
Installingthenullmodemdriver
ConfiguretheserialinterfaceviatheLLTmenu:Connection|Serialinterfaceproperties.
Ifnomodemhasbeeninstalledonthiscomputer,thefollowingscreenappears:
900001549R1100001_29610741079/96
Copyright2009Ingenico
Allrightsreserved
Click"Add"buttontoinstallthenullmodemdriver.
900001549R1100001_29610741080/96
Copyright2009Ingenico
Allrightsreserved
ChecktheoptionDon'tdetectmymodem;IwillselectitfromalistandthenclickNextbuttontoselect
thenullmodemdriverfromalist.
900001549R1100001_29610741081/96
Copyright2009Ingenico
Allrightsreserved
In that case select (Standards Modem Types) from the list Manufacturer and Communications cable
betweentwocomputersfromthelist"Models".
ThenclickNextbuttontoselecttheserialportthatwillbeusedfortheconnection.
900001549R1100001_29610741082/96
Copyright2009Ingenico
Allrightsreserved
SelectaspecificportorAllportsifyouwanttobeabletouseeitheroneortheother.
ContinuebyclickingNextbutton
thenclickFinish.
Thenewinterfaceappearsnowfromthelist.
900001549R1100001_29610741083/96
Copyright2009Ingenico
Allrightsreserved
ClickOKtovalidatethesesettings.
12.5.1.2.
Useofanotherserialport
Itispossibletodefineseveralserialportsinordertoselectlatertheavailableport(SeechapterSelecting
communicationport.Todefineanewinterfaceandanewserialport(forexampleusingCOM2),repeat
thepreviousstepdescribedinInstallingthenullmodemdriver
12.5.1.3. Selectingcommunicationport
SelecttheserialportusedviatheLLTmenu:Connection|Connectionconfiguration.
Selecttheporttouseinthedevicelist.
Selecttheporttouseinthedevicelist.
Iftheserialportisnotdisplayedinthedevicelist,checkifithascorrectlydefined(seeInstallingthenull
modemdriver)
BeforeusingLLTapplicationcheckthatLLTcableiscorrectlypluggedintotherightserialconnector.
900001549R1100001_29610741084/96
Copyright2009Ingenico
Allrightsreserved
12.5.1.4. Communicationportconfiguration
SelecttheserialportusedviatheLLTmenu:Connection|Serialinterfaceproperties.
SelecttheportandclickProperties.
900001549R1100001_29610741085/96
Copyright2009Ingenico
Allrightsreserved
SelectChangesettings.
900001549R1100001_29610741086/96
Copyright2009Ingenico
Allrightsreserved
InModempanel,chooseMaximumPortspeed:115200.
InAdvancedpanel,selectChangeDefaultPreferences
900001549R1100001_29610741087/96
Copyright2009Ingenico
Allrightsreserved
AndverifyPortspeed(115200)andFlowcontrol(None).
ClickOKinthedifferentopenedwindowstovalidthesesettings.
WARNING:ThePCmustberestarted.
12.5.2. ConnectionwithUSBcable
Tobeconnectedtoaterminal,anUSBcablemaybeusediftheterminalsoftwareconfigurationauthorizes
it.
12.5.2.1. TeliumUSBdriverInstallation
PuttheterminalinLLTmode(terminalmustdisplayLLT).
ConnectUSBcablebetweenterminal(USBSlave)andPC(USBHost).
WhenyouplugtheterminalwithUSBcable,WindowsSevendisplaysthefollowingmessage.
ToinstallanewdriverinordertomanageUSBterminalconnection,selectviatheLLTmenu:Connection|
Devicemanager.
900001549R1100001_29610741088/96
Copyright2009Ingenico
Allrightsreserved
Warning:ifthedevicemanagerpanelisnotdisplayed,closeandrestarttheLLTapplication.
SelecttheUnknowndeviceand(witharightclick)UpdateDriverSoftware
Afterlocateandinstalldriversoftwaremanually(Browsemycomputerfordirversoftware):
900001549R1100001_29610741089/96
Copyright2009Ingenico
Allrightsreserved
ClickBrowsetoselectthesubfolderdriversunderLLTinstallationfolderandclickNext.
CheckUSBdriveriscorrectlyinstalledandclickClose.
900001549R1100001_29610741090/96
Copyright2009Ingenico
Allrightsreserved
Now,thenewdeviceisdisplayed.
900001549R1100001_29610741091/96
Copyright2009Ingenico
Allrightsreserved
Now,theUSBdriverisinstalledandreadytobeused.TheUSBconnectionisseenbyLLTasaserialport.
Youmustbuildthisinterface.
Tobuildthisinterface,selectviatheLLTmenu:Connection|Serialinterfaceproperties.
AndselectAdd.
SelectDontdetectmymodemandclickNext
900001549R1100001_29610741092/96
Copyright2009Ingenico
Allrightsreserved
SelectCommunicationcablebetweentwocomputersandclickNext
900001549R1100001_29610741093/96
Copyright2009Ingenico
Allrightsreserved
SelecttheportnumberandclickNext
ClickFinish
900001549R1100001_29610741094/96
Copyright2009Ingenico
Allrightsreserved
Warning: if the following screen is displayed, check Public networks for this program (LLT) and click
Allowaccess.
Ifnot,thefollowingwindowswillbedisplayedafterLLTconnectionaction.
900001549R1100001_29610741095/96
Copyright2009Ingenico
Allrightsreserved
*296107410*
Yourcontact
Ingenico
192avenueCharlesdeGaulle
92200NeuillysurSeineFrance
Tl.:+33146258200Fax:+33147725695
www.ingenico.com