Académique Documents
Professionnel Documents
Culture Documents
CONTENTS
Description ............................................................................................................................................. 3
1.1
1.2
Specifications ........................................................................................................................ 5
1.3
2.1
Mounting................................................................................................................................. 7
2.2
Operation ............................................................................................................................. 11
2.3
Settings................................................................................................................................. 14
2.4
Range Settings.................................................................................................................... 16
Description
1.1 Entrance Control System 61-200-3103
1.2 Specifications
1.3 Packing list
Entrance:
After confirming the equipment conformity, the tripod is unlocked.
The operator can enter by pushing the upper arm to rotate the tripod.
Exit:
Tripod is unlocked via button.
Features:
Arms are locked when they are not turned after a passage authorization
Pictograms display the respective walking directions while entering or leaving the EPA
1.2 Specifications
Power Voltage
240 VAC 10 %, 50 Hz
Test voltage
Test range
20 VDC 5%
Min : 100 k ; Max : 35 M
ca. 510 mm
3 seconds
4 x M12 lag bolt
Stainless steel
Turnstile : 30 Kg ; Packed : 55 Kg
Turnstile : 16,5 x 13 x 38,5 (W x D x H) ; Packed : 15,75 x 18,5 x 41,75
Warranty
1 year
Certifications
Turnstile 61-200-3103
Power cord
Footplate for 61-200-3103
Black cable-gland
Tripod system
3 Tripod fixation screws
One set of two (2) keys
This manual
2.1 Mounting
1. First, choose an installation position according to the site and ensure that the turnstile
correctly prevents access to the EPA. For a better adaptation to different configurations,
the turnstile is equipped with grommet on the right side, the left side and the rear.
2. Open the front panel with the keys provided.
3. With a permanent marker, draw the position of the mounting holes on the floor.
4. Move the turnstile and drill the holes with a hammer drill.
5. Place the dowels into the holes, reposition the turnstile and tighten the four lag bolts so
that the turnstile is completely stable.
If the pre-drilled mounting holes do not correspond to the site configurations, it is possible to
drill new holes using a metal cutting drill.
6. Pass the power cord inside the cable-gland and fix it to the turnstile.
! Ensure the correct plug colour is connected to the corresponding right/left shoe
electrode!
10. Place the tripod system on the turnstile and fix it with the 3 bolts (use a size 6 Allen key)
11. Check if wires/bolts are correctly fixed and if nothing is obstructing the rotation of the
arms.
12. Switch the turnstile power on and close the front panel.
13. To lock the middle arm, push it down to its maximum and then lift it until hearing the
sound of the magnet.
For safety reasons, emergency stop can be installed on the supply cord of the turnstile.
In case of Power interruption, the middle arm will fall.
2.2 Operation
To ensure the proper operation of the equipment, please:
-
Do not force the rotation of the arm when the passage is locked.
The turnstile should be used in an internal area protected from humidity.
1. Before testing, the top screen displays the following label, which indicates that the
passage is locked.
3. Attach the wrist strap to the connections on the front side of the turnstile.
Female banana
plug
4mm Snap
Male banana
plug
10 mm Stud
4. The measurement starts by touching the sensitive electrode on the top of the turnstile. A
bip sound and two green LEDs indicate the beginning of the test
6. If the test is compliant, the top screen displays a green arrow which indicates that the
passage is unlocked and which shows the entry direction.
7. Push the middle arm with body to rotate the tripod and enter the EPA.
8. If the test is not compliant, the top screen doesnt change and nothing happens.
9. To quit the EPA, no test is needed. Push the button on the side of the turnstile, the top
screen displays a green arrow which indicates the exit direction.
2.3 Settings
The 61-200-3103 turnstile is equipped with shoes & wrist strap tester. To suit all types of
needs, it is possible to choose the equipment to be tested: shoes only / wrist-strap only /
shoes & wrist-strap.
1. Open the top cover with the keys provided.
2. The tester mainboard is located on the right hand side, on the left of this electronic board
there is a setting button.
Wrist-strap only
Shoes only
2. The tester mainboard is located on the right hand side. A RS232 plug is connected under
this board. Unplug it and proceed to the following instructions :
3. Proceed in the same manner as in Chapter 2.3 and stop at point 4. Once the equipment
to be tested is selected, simultaneously press the setting and test buttons.
13. The green LED flashes once time and the Footplate Low limit's red LEDs are illuminated.