Académique Documents
Professionnel Documents
Culture Documents
If the generating point is on the generating circle and the generating circle is outside the directing circle,
the curve obtained is:
(a) Inferior hypotrochoid (b) epicycloids (c) hypocycloid (d) superior trochoid
6. To obtain the true shape of the section of solid, an auxiliary plane is set
(a) Inclined at an angle of 45o to a cutting plane (b) parallel to XY (c) Parallel to a cutting plane(d)
perpendicular to a cutting plane
7. If a line is inclined to the Vertical Plane and parallel to Horizontal Plane, then which of the following
statements is always CORRECT?
(a) True Length = Plan Length (b) True Length Plan Length (c) True Length > Elevation Length (d)
True Length = Elevation Length
Q.1 (b) State true or false for the following sentences:
1. Dashed lines are used to show outlines of the adjacent part. Ans. False
2. Measurement of the distances is simpler in a diagonal scale than a vernier scale. Ans. True
3. If front view of a line is parallel to XY, its Top View gives True Length. Ans. True
4. The eccentricity of parabola is less than the eccentricity of a hyperbola. Ans. True
5. A horizontal section plane will create a sectional Front View. Ans. False
2.
A.
360
B.
180
C.
270
D.
310
A line drawn with a long section, short dash, and another long section is a ________.
A.
hidden feature
B.
center of a circle
C.
D.
center of a radius
3. Traditional drafters need to be able to create several different line widths because ________.
4.
5.
6.
7.
A.
B.
the line width has to do with how dark it appear in the finished drawing
C.
D.
it makes no difference
B.
45 degree triangle
C.
Circle template
D.
A civil engineer working on a bridge design would probably rely on his ________ scale for
checking printed drawings.
A.
engineer's
B.
metric
C.
architect's
D.
B.
C.
D.
An engineer's scale would be used to measure lines on a drawing where the scale factor reads
________.
8.
9.
A.
/4" = 1'-0"
B.
C.
1" = 100'
D.
/8" = 1'-0"
/4" = 1'-0"
Referring to the fractional inches to decimal inches to millimeter conversion chart on page 55 what
is the equivalent mm measurement of 3/16 inch.
A.
1.906
B.
4.7625
C.
5.958
D.
14.6844
Some traditional board drafters preferred the drafting machine over the parallel straight edge
because it could be used without the need for________.
A.
circle templates
B.
triangles
C.
technical pens
D.
lettering guides
.1
2.
3.
A.
B.
C.
align the paper so that it will be positioned square to the parallel bar
D.
If a designer is developing a plan for a project in which the entire part is made out of " thick
plywood and he only wants to use one view, he should use the ________ view.
A.
front
B.
top
C.
right
D.
back
In developing a multi-view drawing the drafter can use a ________ line to help locate the top and
right side views.
A.
object
B.
hidden
C.
dimension
D.
miter
The type of line that projects from an object for the express purpose of locating a dimension is a
________ line.
4.
5.
6.
7.
8.
A.
visible
B.
hidden
C.
extension
D.
dimension
arcs
B.
circles
C.
D.
Architectural drawings used to construct a house are often plotted with a scale of " = 1'-0".
What scale is this?
A.
Quarter
B.
Half
C.
Full
D.
Double
In multi-view drawing it is common practice to include three views, the front, the top and the right
side. If no dimensions are required on the right side view the drafter can ________.
A.
B.
C.
D.
The AutoCAD command used to combine two or more primitive shapes into a single complex 3dimensional model is ________.
A.
add
B.
union
C.
attach
D.
form
Most architectural drawings produced for field use by building contractors are printed on
architectural "D" size paper which measures ________.
A.
24" X 36"
B.
18" X 24"
C.
11" X 17"
D.
34" X 22"
2.
3.
5.
6.
7.
Drafters should use a ________ in a section view of a mechanical part that includes the cylindrical
view of a threaded hole.
A.
Center line
B.
Hatch line
C.
Poly line
D.
Dimension line
The section view drawing in which one fourth of an object has been marked for removal is known
as a ________ section.
A.
full
B.
half
C.
quarter
D.
When filling an area with a hatch pattern in AutoCAD the drafter needs to be able to ________.
A.
B.
set Ortho on
C.
D.
To avoid having to dimension to a hidden feature the drafter can utilize a ________ section.
A.
whole
B.
half
C.
broken out
D.
Objects that are symmetric can be shown effectively using this type of section:
A.
Quarter section
B.
Half section
C.
Full section
D.
Symmetric section
9.
By using a ________ section of a cylindrical mechanical part the drafter should be able to show
only one view of the part.
A.
half
B.
whole
C.
revolved
D.
broken out
10. In the section view, the areas that would have been in actual contact with the cutting plane are
shown with:
A.
B.
Section lining
C.
Visible lines
D.
12. In architectural drawing ________ are often used to illustrate and detail structural components.
A.
B.
Wall sections
C.
Building sections
D.
13. When only a small section of an interior area needs to be revealed the drafter can use a ________
section.
A.
half
B.
quarter
C.
full
D.
broken out
15. A ________ section allows the drafter to create a Cutting Plane line which is not in a straight line
across the part.
A.
Offset
B.
half
C.
whole
6.
1.
2.
This type of surface is tipped to all principal planes of projection and does not appear true size in
any standard view:
A.
Foreshortened
B.
Parallel
C.
Orthographic
D.
Oblique
Parallel lines converge toward a single point on the horizon called the vanishing point. True
B.
Minor diameter
C.
Major diameter
D.
3.
Idea or concept sketches are usually not considered to be technical drawings. False
4.
When creating a block the drafter needs to pay particular attention to selecting a base point
because it determines the ________.
A.
scale
B.
rotation angle
C.
insertion point
D.
color
5.
After a drawing has been released, an engineering change order is used to document and
approve drawing changes. True
6.
Traditional drafters need to be able to create several different line widths because ________.
A.
B.
the line width has to do with how dark it appear in the finished drawing
True
B.
False
Answer: Option B
Learn more problems on : Technical Sketching
Discuss about this problem : Discuss in Forum
14. An architect does not need to know how many people are going to live in a house before he
begins his design.
A.
True
B.
False
Answer: Option B
Learn more problems on : Technical Sketching
Discuss about this problem : Discuss in Forum
15. This type of section is not in direct projection from the view containing the cutting plane:
A.
Revolved section
B.
Removed section
C.
Broken-out section
D.
Full section
Answer: Option B
Learn more problems on : Sectional Views
Discuss about this problem : Discuss in Forum
16. Drafters should use a ________ in a section view of a mechanical part that includes the
cylindrical view of a threaded hole.
A.
Center line
B.
Hatch line
C.
Poly line
D.
Dimension line
Answer: Option A
Learn more problems on : Sectional Views
Discuss about this problem : Discuss in Forum
17. A groove weld is a type of arc and gas weld.
A.
True
Answer: Option A
Learn more problems on : Welding Representation
B.
False
True
B.
False
Answer: Option A
Learn more problems on : Gears and Cams
Discuss about this problem : Discuss in Forum
19. A plane surface always projects either on edge or as a surface in any view.
A.
True
B.
False
Answer: Option A
Learn more problems on : Orthographic Projection
Discuss about this problem : Discuss in Forum
20. The center line of a hidden cylinder feature appearing in the front view should line up with the
center mark in the corresponding circle which appears in the auxiliary view.
A.
True
B.
False
Answer: Option A
Learn more problems on : Auxiliary Views
Discuss about this problem : Discuss in Forum
1.
These include taper pins, straight pins, dowel pins, clevis pins, and cotter pins:
A.
Bolts
B.
General fasteners
C.
Machine pins
D.
Rivets
Answer: Option C
Explanation:
No answer description available for this question. Let us discuss.
View Answer Workspace Report Discuss in Forum
2.
3.
Lead
B.
Pitch
C.
Turn
D.
Crest
The standard number of threads per inch for various diameters is the:
A.
Series of thread
1.
B.
C.
D.
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Workspace Report Discuss in Forum
2.
B.
C.
D.
Answer: Option A
Explanation:
No answer description available for this question. Let us discuss.
View Answer Workspace Report Discuss in Forum
3.
Engineering process
B.
Design process
C.
Aesthetic process
D.
Functional process
Answer: Option B
Explanation:
No answer description available for this question. Let us discuss.
View Answer Workspace Report Discuss in Forum
4.
This is the range of digital or hard copy documents that specify the physical function requirements
for a product:
A.
Product design
B.
Product definition