Académique Documents
Professionnel Documents
Culture Documents
constructive solutions
Liquid
applied
single
component
elastomeric waterproofing membrane
Uses
Advantages
One component; ready to apply direct from the can.
Properties
App. 2 hours
App. 48 hours at 1.3 mm
thickness
o
Page 1
Nitoproof 600
Chemical properties
Application instructions
Preparation
All surfaces to be waterproofed should be sound, clean
and dry.
Concrete surfaces should have a light steel-trowel
followed by a fine hair-broom or equivalent finish which is
dry and free of dust, oil and other contaminants. All high
spots should be removed.
Application
Nitoproof 600 should be applied by brush, trowel, roller,
squeegee or airless spray (two coat application for
standard grade on vertical surfaces) at a minimum wet film
thickness of 1.3 mm (1.5 kg/m2). This is in addition to the
preparatory work.
Priming
Priming is not normally required on good quality concrete
substrates. However, high absorbent surfaces such as
porous concrete, sand/cement and cement boards will
require sealing to prevent absorption of Nitoproof 600.
This should be done using 1:1 mixture of Nitoproof 600
and Fosroc Solvent 101. Use Nitoflor FC130 Clear as a
primer for bituminous surfaces and Fosroc Primer 4 for
metal, glazed and PVC surfaces. All metal and PVC
surfaces should be cleaned and abraded before priming.
Movement joints
All expansion and movement joints should be sealed with
Nitoseal 200 or Nitoseal 220 (or as per Fosroc
representative recommendations). When cured, Nitoseal
Debonding Tape should be applied to the top surface of
the sealant and the joint then over-coated with a 1.3 mm
thick application of Nitoproof 600 extending 150mm each
side of the tape. Embed a 100 mm or 150 mm wide strip
of Nitoproof Scrim, then allow to cure before general
application.
Cracks
constructive solutions
Page 2
Nitoproof 600
constructive solutions
Page 3
Nitoproof 600
Flood test
Storage
Shelf life
At least 9 months if stored in original unopened containers
under normal warehouse conditions.
Storage conditions
Nitoproof 600 membrane must be cured for a minimum of
24 hours at 25oC before placing protection. Where damage
to the membrane is possible (by traffic, back-filling etc.) it
should be protected by a cementitious screed or protection
boards. A dust coat of cement should be used to prevent
adhesion of the membrane to the boards. Where a bond
with the topping is not required, a separator sheet should be
used.
Fire
Nitoproof 600, Fosroc Primer 4, Nitoproof Reflectacoat and
Fosroc Solvent 101 contain flammable solvents. Do not
use near an open flame or smoke during use.
Estimating
Supply
Nitoproof 600:
Nitoflor FC130 Clear:
Nitoproof Reflectacoat:
Nitoproof Scrim:
Fosroc Primer 4:
Fosroc Solvent 101:
Flash points
25 kg pails
5 kg pack
5 and 25 litre containers
100mm and 150mm width
rolls
1 litre packs
5 and 25 litre containers
Coverage
Nitoproof 600:
Nitoflor FC130 Clear:
Fosroc Primer 4:
o
45 C
o
10 C
o
40 C
o
23 C
Important note:
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions
for the Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that
any advice, recommendation, specification of information it may give is accurate and correct, it cannot, because it has no direct
or continuous control over where or how its products are applied, accept any liability either directly or indirectly arising from the
use of its products, whether or not in accordance with any advice, specification, recommendation of information given by it.
www.fosroc.com
email: fosam@fosroc.com
Regional Offices
Jeddah Sales Office
Jeddah Showroom
Riyadh
Dammam
Khamis Mushayt
Registered Office: Industrial Area, Phase 4, Road No. 414, Street No. 407
Page 4
FO SA/Nitoproof 600/05/A