Académique Documents
Professionnel Documents
Culture Documents
This activity is a follow-up on the skills learned in the File Folder tutorial. The tray
itself has no specific purpose. It was designed to teach additional sheet metal
modeling skills not already covered in the previous exercise. Before attempting
this tutorial, please review the File Folder exercise.
Procedure:
Launch the Inventor Program. Create a folder and a path file for this tutorial.
Each sheet metal part has a number of Parameters, which can be established at
the beginning of the part creation. They include defining the extrude distance
(which stays constant throughout the part model), the material the part is to be
made from, the bends and the corners.
From the panel bar heading, choose Sheetmetal Features from the drop-down
menu. This will bring up the sheet metal tool bar.
Click on the
Click on the New button to establish a new Sheet Metal Style. Highlight the
words Copy of Default and type: Sheet Metal Tray.
In the Sheet tab of the dialog box, change the material to Stainless Steel 440C
and enter .050 as its thickness.
Under the Bend tab, change the Relief Shape to Round, and under the Corner
tab leave the Corner Relief shape as Trim to Bend.
Click on the Save button to save the new Sheet Metal Style. Click on the arrow
in the Active Styles window and make Sheet Metal Tray the active sheet metal
style. Click on the Done button.
Click on the Offset button to change the direction that the face will be created
(arrow should point to the back), and then click OK.
Notice that the tool panel on the left side of the screen has changed to the Sheet
Metal settings.
Choose
The Flange dialog box will open. With the selection arrow depressed, click on
the right edge of the sheet metal plate to establish the location of the flange.
Enter the formula 2 in /sin(60 deg) for the Distance. (This is so the height of
the end wall will match the height of the sidewalls.)
Depress the Edge button so that the thickness of the flange will point away from
the plate. (See Figure below.)
Click Apply.
Depress the Edge button so that the thickness of the Flange will point away from
the plate. (See Figure below.)
The next step is to create the side Flanges. Since they are not rectangular in
shape, the sides will be created with a Sketch rather than the use of the Flange
command. The sides can expand to fill the space created by the angled ends.
Rotate and Zoom the part to create a Sketch Plane on the long, angled edge of
the model (see below).
Draw a rectangle Coincident to the top edge of the face with no specific width,
but with a Dimensioned height of 2-inches.
Right click to exit the Dimension tool. Right click again and select Create
Feature Face. Choose the profile of the Sketched rectangle. Click the
Offset button to change the direction of the thickness so that it is pointing away
from the model as shown below.
Click OK to complete.
The Corner Seam command will be used to extend the square edges of the new
side to the angled edges of the end walls. This command is used to create
Seams between faces that are intersecting or coplanar.
Choose
The Corner Seam dialog box will open. Select the outside edges of the two
intersecting sides on the right end of the box as shown below.
Enclose the 4th side by following the steps just covered: create a Sketch Plane,
draw a rectangle of no specified width and 2 inches high, create the face being
sure to identify the correct direction, and use the Corner Seam command to
extend the sides to meet.
Cutting Holes
The next step is to put a set of holes in the bottom of the tray.
Place a Point, Hole Center and dimension its distance from the edges as shown
below.
Choose
from the panel tool bar. The Holes dialog box will open.
Change the Hole diameter to 0.5 in. and the Termination to Through All, as
shown in the Figure below.
Place a new Sketch Plane on the top side of the bottom of the tray.
This will open the Cut dialog box. (Another way to find the dialog box is to rightclick Finish Sketch and choose the Cut icon in the panel tool bar.)
Click OK.
Adding Flanges
The next step will be to add Flanges to the Perimeter of the tray, as if it were to
be mounted on the inside of a cutout.
Click on the Flange tool. Begin with the long side of the tray.
Enter and Angle of 90.0. (This will keep the flange parallel to the base.)
The Flanges for the remaining two sides will have to be created with an angle
equal to the angle of the side.
The next step will be to have the flanged edges meet at a mitered corner.
Click the
Select the top edges of two adjacent flanges to form the miter.
Click Apply.
Practice Exercise: