Académique Documents
Professionnel Documents
Culture Documents
ABSTRACT
This paper deals with the design & analysis of the Microcontroller based Smart battery charger specifically designed for
multimode operation to ensure no power cut. The main objective of this paper is to provide uninterrupted power supply to a
load by selecting the power supply from multiple sources such as Mains, Solar Power, Battery Bank and Generator
automatically on the basis of their priority. The design and performance analysis of a power factor corrected (PFC), single
switch forward buck converter of proposes Smart Charger is carried out for low power battery charging applications. The
battery charger main highlighting features are low cost, fast charging, high power factor, high efficiency, minimum ripple and
high reliability. The converter is designed with the help of an isolated single switch forward buck converter topology operating
at discontinuous mode.
Keywords: Battery Charger, Microcontroller, Single switch, isolated forward Converter, DCM, Power factor,
Efficiency.
1. INTRODUCTION
The demand for electricity is increasing day by day and frequent cuts are causing many problems in various areas like
industries, hospitals and houses. An alternative arrangement for power source is a must. We are facing many real time
challenges in day to day activities due to limited electricity supply. Even after having electrification, solar panels and
backup of different sources, simultaneous functioning of their operations and handling are herculean tasks. .Out of
these challenges, important one is availability of electricity which is variable and unreliable.
To overcome this, many solar power system solutions are available. But it these are economically not viable for heavy
load since there is a need of excess backup capacity. Also due to fluctuating weather conditions makes the system more
vulnerable to power outage.
To overcome these shortcomings, a smart power system block diagram Fig.-1 is proposed to work either on solar panel
or local power distribution. In both available power scenarios the solar power is considered as reference one.
Page 7
Page 8
The data collected after different simulation and experiments on platform are satisfactory and performance of our
proposed converter has been improved. The observation shows the power factor at AC input mains is 0.986 and full
load efficiency order of 82.6%.
Tri-state charging [2] method is used for maximizing the extraction of available solar energy for fulfillment of second
criterion. In first state, the battery is charged at maximum solar current till the battery voltages reaches first threshold
voltage. In next state the charging current is in burst of pulses where the time between two bursts increases with
increase in state of charge of battery thus the charging current is in burst of pulses where the time between two bursts
increases with increases in state of charge of battery thus the charging current matches change in impedance of battery
bank.
3. ELECTRONIC CONTROL CIRCUIT DESIGN
This module [7] has four switches which are used to demonstrate the respective failure of respective power supply.
When any of the switches is pressed it shows the absence of that particular source, switches are connected to
microcontroller as input signals. A microcontroller of 8051 family or by using a 16bit INTEL80196 C the designing
will be done according to the hour of need. Inbuilt A/D converters will measure the change in charging current, battery
voltage to estimate change in state of charge (SOC) of battery bank..The output of microcontroller is given to the relay
driver IC , which switches appropriate relay to maintain uninterrupted supply to the load . The output shall be observed
using a lamp drawing power supply from mains initially. On failure of the mains supply (which is actuated by sing the
appropriate switch) the loads gets supply from the next available source, say an inverter .If the inverter also fails it
switches over to the next available sources and so on .the current status ,as to which source supplies the load is also
displayed on an LCD. As it is not feasible to provide all 4 different sources of supply, one source with alternate switches
are provided to get the same function.
Page 9
This project can be further enhanced by using other sources like wind power also and then taking into consideration for
using the best possible power whose tariff remains lowest at that moment. .
3. CONCLUSIONS
The simulated and experimental results shows the developed charger is highly efficient and meets the regulatory
requirement of emission standards [4], [5] since it has high power factor with low current harmonics. It also meets
green product criteria as it gives precedence to renewable energy source and charge battery bank to its utmost capacity
by matching the charging current to change in impedance according to charging state.
REFERENCES
[1] P.R.K. Chetty, Switch-Mode Power Supply Design, BPB Publications, 1987.
[2] B.K. Bose, Recent advances in power electronics, IEEE Trans. On Power Electronics, Vol.7,No.1, pp.
2~16,Jan.1992.
[3] Bhim Singh and Ganesh Dutt Chaturvedi, Analysis, Design and Development of a Single Switch Flyback BuckBoost AC-DC Converter for Low Power Charging Applications, Journal of Power Electronics, Vol. 7, No. 4,
October2007.
[4] IEEE Guide for harmonic control and reactive compensation of Static Power Converters
IEEE standards 5191992.
[5] Limits for harmonic current emissions, International Electrotechnical Commission Standards 61000-3-2, 2004.
[6] R. Navaneethan, E. Annie Elisabeth Jebaseel I, A Single Phase Ac-Dc Converter with Improved Power Factor
And Harmonic Reduction, IJTEEER, Vol.2, Issue 3.
[7] Adamu Murtala Zungeru, Ambafi James Garba, Jonathon Gana Kolo, Mahmud Shehu Ahmed and Ijarotimi
Olumide, Design Of A Smart Embedded Uninterrupted Power Supply System For Personal Computers
Page 10