Académique Documents
Professionnel Documents
Culture Documents
Whereas the Parliament of India has set out to provide a practical regime of right to
information for citizens to secure access to information under the control of public authorities,
in order to promote transparency and accountability in the working of every public authority,
and whereas the attached publication of the Bureau of Indian Standards is of particular interest
to the public, particularly disadvantaged communities and those engaged in the pursuit of
education and knowledge, the attached public safety standard is made available to promote the
timely dissemination of this information in an accurate manner to the public.
1 +, 1 +
01 ' 5
Jawaharlal Nehru
! $ ' +-
Satyanarayan Gangaram Pitroda
! > 0 B
BharthariNtiatakam
UDC 6218822166
: 6217533
IS : 7479 - 1985
Indian Standard
El
SPECIFICATION
RECESS PENETRATION
( First
( Reaffirmed 2001 )
FOR
GAUGES
Revision )
33
GA
BO
ZERO
POSITION
FIG. 1
3. Dimensions
CONTROL
POSITION
The dimensions
4. Finish - The gauge point shall be hardened to 750 HV minimum [see IS : 1501-1969
Vickers hardness test for steel (first revision ) I and ground to obtain a good finish.
,5. Material
6. General
Method
of
Requirements
Shall be designated
recess penetration
gauge shall
conform
to IS : 2092-1983
Example :
A recess penetration
Gauge 2 IS : 7479
Or 2
I
INDIAN
MANAK
STANDARDS
SHAVAN,
as:
INSTITUTION
ZAFAR MARG
0 BAHADUd
SHAH
NEW DELHI llOqO2
1s : 7479
- 1985
TABLE
GAUGE DIMENSIONS
FOR RECESS TYPE H
( Clause 3 )
All dimensions in millimetres.
SECTION XX
VIEW
Gauge No.
1'001
064
-CO25
1530
0813
+oo026
2286
127
0.38
025
+:*13
038
0613
0315
-i-025
1102
- .
-_
061
031
--JO6
-
317
3.16
038
.-
. _
- .
146
153
6 45
6 45
874
714
112
140
2738
097
471
138
7
-
038
-_
- _
+15
0
-k
508
__
Min
391
2098
0.64
_-
cc
3674
. -
-_
2497
__
se
me
-_
.b
IS : 7479
8. Packing - Gauges shall be coated with
damage during transit.
9. Marking
a suitable
rust
preventive
and packed
with
- 1985
so as to
prevent
the following:
name or trade-mark.
Marking
Details available
with
the Indian
Standards
APPENDIX
Institution.
( Clause 1 )
METHOD
OF PENETRATION
GAUGING
OF CROSS
RECESSES
A-l.
The penetration
depth of the depth gauge ( minimum dimensions ) is indicated
product standards.
It is the test dimension for the usability of the cross recess.
in the different
A sleeve serves
A-2. The point of the gauge is identical with the point of the respective screwdriver.
This plane passes through the point of intersection
to guide the ~gauge and fix the reference plane.
It corresponds thus to the surface of a
of the recess wings and the top surface of the screw head.
screw with flat head.
In the case of crowned screw heads, it lies below the crown in the transition
For these screw heads, the reference plane is
area from the recess wings to the surface of the head.
fixed with the help of the bearing surfaces of the gauge sleeve.
A-3. The penetration
The zero and control
A typical
of recess penetration
EXPLANATORY
a dial
an inaccuracy
gauge.
of up to
NOTE
Cross recesses
taken
for
up to align
screws
issued
this
by
3
Printed at Printrade,