Académique Documents
Professionnel Documents
Culture Documents
December 2012
Analyzer Update
1 In this version
This release contains support for new and updated file formats. There are updates for most
technologies that Actix supports, with changes falling under the following categories:
Platform improvements:
Support has been added for UTF-8 cellrefs files (as exported
from ActixOne).
A problem with the TAB export feature in the map has been
corrected that affected enumerated attributes.
December 2012
[Case 69662] In LTE, a problem that could cause Analyzer to crash has
been resolved with the decoding of the scanner message Enhanced Top
N Pilot Scan Response.
In LTE, the special encoding of Qualcomm message 0xB126 used by
TEMS is now supported.
[Case 64237] In GSM, when an Ericsson handset is used as a scanner,
the messages that report measurements for a subpart of the GSM
frequency band are now aggregated so that the GSM scanner attributes
set by Analyzer (such as ScanSortSigLevel_by_SigLevel) are set for
the whole GSM frequency band at once.
[Case 49792, 80200] Added support for Ascom TEMS Symphony version
6.1.3.
[Case 69278] In UMTS, a problem has been resolved that could make
Analyzer crash when the message HSDPA HS DPCCH reported no subframe.
[Case 66850] Added support for RSSI Scan message type.
December 2012
[Case 1464] A problem has been resolved in decoding the log files
header that could prevent some log files from loading in Analyzer.
[Case 14506] A problem has been resolved with Nemo Indoor marker
file support, which could cause Analyzer to only use one set of GPS
coordinates instead of all the markers.
[Case 68767] A problem has been resolved with superstreaming that
affected Nemo files loaded with preference General Settings > Nemo >
Auto-load device files enabled.
[Case 49947] The GSM Hopping stateform now also displays GSM C/I
for Nemo files.
[Case 69189] In LTE, a problem has been resolved that could prevent
LTE RRC attributes from being set for CDMA/EVDO capable devices.
2.11 Generic
In LTE, the ASN.1 containers (such as Source-ToTargetTransparentContainer in S1AP protocol) are now decoded.
December 2012
[Case 80016] In LTE, a problem has been resolved whereby LTE NAS
ciphered messages could cause Analyzer to crash.
[Case 65987] In LTE, the event detection now uses the T300 values
indicated in the RRC messages to detect RRC Connection Setup failure
events.
[Case 70722] In UMTS, a problem has been resolved that could prevent
the attribute Uu_HSPACallDropped from being set.
[Case 31655] In UMTS, a problem has been resolved that could cause
more cell reselection events to be detected by Analyzer when Load All
preference was selected instead of Load Time Message Filtering.
[Case 80042] In UMTS, a problem as been resolved that could prevent
the RRC attributes set at Measurement Control messages for event 2d
and event 2f from being set (such as Uu_RRC_Event2d_hysteresis).
In addition new attributes are set for inter-frequency measurement
parameters:
[Case 63632, 65914] A problem has been resolved that caused the
preference General Settings > Disable Scanner Load Time Message
Filtering to be ignored if the preference General Settings > Merge
Scanner and Handset Data was enabled.
December 2012
In LTE, a new KPI was added for inter-frequency handover failure rate.
[Case 67555] In LTE, the diagnostic for RRC dropped connections and
for failed handovers has been improved.
December 2012
[Case 61409] In GSM, RxQual is now displayed on the map when the
RxQual KPI is selected in Radio Network Explorer.
December 2012
4 Platform improvements
4.1 General
[Case 69292] Support has been added for UTF-8 cellrefs files (as
exported from ActixOne).
[Case 5723] A problem has been resolved that could cause Analyzer to
crash because of a lack of memory when the GetFormatted function
was used in queries.
[Case 66840] A problem has been resolved whereby Network Explorer
did not display correctly when a Site Id was 0.
[Case 58155] A problem has been resolved that could cause queries to
produce incorrect results when a query was edited and re-run in the
same Analyzer session.
[Case 6900] A problem has been resolved that caused TAB exports of
enumerated attributes to contain only 0 values instead of the expected
text values.
December 2012
5 Documentation
None
December 2012
None
December 2012
10
December 2012
11
US:
AE
AU
BR
CN:
DE:
HK:
JP:
SG:
UK:
Support
+44 (0)20 8735 6303