Académique Documents
Professionnel Documents
Culture Documents
Introduction
There are a number of important reasons for determining areas. One is to include
the acreage of a parcel of land in the deed describing the property. Other purposes
are to determine the acreage of fields, lakes, etc., or the number of square yards to
be surfaced, paved, seeded, or sodded. Another important application is
determining end areas for earthwork volume calculations.
In plane surveying, area is considered to be the orthogonal projection of the surface
onto a horizontal plane. In the English system the most commonly used units for
specifying small areas are the ft2 and yd2, and for large tracts the acre is most often
used, where 1 acre = 43,560 ft 2. In the metric system, smaller areas are usually
given in and for larger tracts hectares are commonly used, where 1 hectare is
equivalent 10,000 m2.
Methods of Measuring Area
1.
2.
3.
4.
Division of the tract into simple figures( triangles, rectangles, and trapezoids)
Offset from a straight line
Coordinates
Double-meridian distances
Formulas for computing areas of rectangles and trapezoids are well known. The area
of a triangle whose lengths of sides are known can be computed by the formula
where a, b, and c are the lengths of sides of the triangle and s = (a+b+c).
Another formula for the area of a triangle is
Where b is the length of a common interval between offsets, h0, h1, ,hn are
the offsets. The regular interval for the example shown on the figure below is
half a station or 50-ft.
Example:
Compute the area of the tract shown in the figure 2.
Solution:
Area = 50( 0 + 5.2 + 8.7 + 9.2 + 4.9 + 10.4 + 5.2 + 12.2
+2.8/2 )
= 2860 ft2
In this example, a summation of offsets (terms within parentheses) can be secured
by the paper-strip method, in which the area is plotted to scale and the midordinate of each trapezoid is successively added by placing tick marks on a long
strip of paper. The area is then obtained by making a single measurement between
the first and last tick marks, multiplying by the scale to convert it to a field distance,
and then by multiplying by width b.
where a, b, c, are varying offset spaces, and h0, h1, h2, are the observed
offsets.
Example:
Compute the area of the tract shown in the figure 3.
Solution:
(1)
The area of each trapezoid, for example EEDDE can be expressed in terms of
lengths as
AreaEEDDE = EE + DD x ED
2
In terms of coordinate values, this same area EEDDE is
AreaEEDDE = XE + XD (YE - YD)
2
(2)
The equation above can be reduced to an easily remembered form by listing the X
and Y coordinates of each point in succession in two columns, as shown in the
equation below, with the coordinates of the starting point repeated at the end. The
products noted by diagonal arrows are ascertained with dashed arrows considered
plus and solid ones minus. The algebraic summation of all products is computed
and its absolute value divided by 2 to get the area.
(3)
The procedure indicated in Equation (3) is applicable to calculating any size
traverse. The following formula, easily derived from Equation (2), is a variation that
can also be used.
(4)
Example:
The figure below illustrates the same traverse as Figure 4. The computations in the
table apply to this traverse. Coordinate values shown in the below, however, result
from shifting the axes so that XA = 0.00 (A is the most westerly station) and Y C =
0.00 (C is the most southerly station). This was accomplished by subtracting
10,000.00 (the value of XA) from all coordinates, and subtracting 4408.22 (the value
of YC) from all Y coordinates. Compute the traverse Area by coordinate method. All
units are in feet.
PF + FG + GP
Thus, the meridian distance for any course of a traverse equals the meridian
distance of the preceding course plus one half the departure of the preceding
course plus half the departure of the course itself. It is simpler to employ full
departures of courses. Therefore, DMDs equal to twice the meridian distances that
are used, and a single division by 2 is made at the end of the computation.
Based on the consideration described, the following general rue can be applied in
calculating DMDs: The DMD for any traverse course is equal to the DMD of the
preceding course, plus the departure of the preceding course, plus the departure of
the course itself. Signs of the departures must be considered. When the reference
meridian is taken through the most westerly station of a closed traverse and
calculations of the DMDs are started with a course through that station, the DMD of
the first course is its departure. Applying these rules, for the traverse in Figure 6
DMD of AB = departure of AB
DMD of BC = DMD of AB + departure of AB + departure of BC
A check on all computations is obtained if the DMD of the last course, after
computing around the traverse, is also equal to its departure but has the opposite
sign. If there isadifference, the departures were notcorrectly adjusted before
starting, or a mistake was madein the computations. With reference to Figure 12.6,
the area enclosed by taverse ABCDEA may be expressed in terms of trapezoid areas
(shown by different color shading) as
Area = EEDDE + CCDDC (ABBA + BBCCB + AEEA)
The area of each figure equals the meridian distance of a course times its balanced
latitude. For example, the area of trapezoid CCDDC = QQ x CD, where QQ and
C D are the meridian distance and latitude, respectively, of line CD. The DMD of a
course multiplied by its latitude equals double the area. Thus, the algebraic
summation of all double areas gives twice the area inside the entire traverse. Signs
of the products of DMDs and latitudes must be considered. If the reference line is
passed through the most westerly station, all the DMDs are positive. The products of
DMDs and north latitudes are therefore plus and those of DMDs and south latitudes
are minus.
Example:
Using the balanced departures and latitudes listed in the table below for the
traverse of the figure 6, compute the DMDs of all courses.
Solution:
Computation of DMD
Example:
Using the DMD determined in the previous problem, calculate the area within the
traverse.
Computation of Area by DMD
SOLUTION
Computation for area by DMDs are generally arranged as in Table 12.4, although a
combined form may be substituted. Sums of positive and negative double areas are
obtained, and the absolute value of the smaller subtracted from that of the larger.
The result is divided by 2 to get the area (272,600 ft) and by 43,560 to obtain the
number of acres (6.258). note that the answer agrees with the one obtained using
the coordinate method.
If the total of minus double areas is larger than the total of plus values, it signifies
only that DMDs were computed by going around the traverse in a clockwise
direction.
AREA OF PARCELS WITH CIRCULAR BOUNDARIES
The area of a tract that has a circular curve for one boundary, as in Figure 12.7, can
be found by dividing the figure into two parts: polygon ABCDEGFA and sector EGF.
The radius R = EG = FG and either central angle = EGF or
R (
)
360