Académique Documents
Professionnel Documents
Culture Documents
CALENT
CALEN TADOR
ADO R INST
INS TANTNEO
D E AGUA
AGU A A GAS
Instrucciones de instalacin, uso y conservacin
Modelos de instalacin
exclusivamente en el exterior:
COB 5 x
COB 10 x
NDICE
PG
PG.
CONJUNTOS FUNCIONALES
COB 5
COB 5 x
Modelos de 10 l/min
17,8 kW
(255 Kcal/min)
COB 10
COB 10 x
Modelo 14l/min
23,8 kW
(341 kcal/min)
COB 14
1. Cortatiro incorporado.
Asegura la correcta combustin aunque vare el tiro en el conducto de
evacuacin de gases quemados (chimenea). Gracias a su nueva concepcin,
la cubierta del calentador est exenta de rejillas.
2. Cambiador de calor.
De cobre electroltico puro, con recubrimiento calrico que asegura la
mxima transmisin del calor al agua.
3. Quemador
De avanzada tecnologa, que aprovecha al mximo el gas consumido.
7. Selector de temperatura.
Sirve para graduar a voluntad la temperatura del agua caliente.
no
no
INSTR
INSTRUCCIONES PARA EL USU
USUARIO
CALENT
CALENTADORES ELECTRNICOS (SIN PILOTO PERMANENTE)
- Comprobaciones previas
1. Asegrese que los grifos de agua caliente estn cerrados.
2. Abra la llave de paso de gas al calentador, situada en la acometida de gas al aparato.
3. Compruebe que las pilas (o bateras) de 1,5 V estn incorporadas en su alojamiento, con
la posicin correcta de la polaridad (+ y -), y est retirado el precinto de seguridad.
4. Que el estado de las mismas tienen carga suficiente para el funcionamiento del
calentador.
- Seleccin manual de la Potencia del Quemador
Para el encendido del aparato gire el mando de gas desde la posicin
hasta una de las 2
posiciones mnima o mximo.
Con el mando de gas, podemos seleccionar la potencia del calentador,mnima( ) o mxima
( ), y posiciones intermedias segn la intensidad del calentamiento del agua que se desee. Puesto el
mando de gas en la posicin
(llama grande), el aparato calienta el agua a plena
potencia. Si la temperatura de sta resultase excesivamente elevada, por ejemplo, en verano
o cuando se necesitan pequeos caudales de agua no muy caliente, para reducir la potencia
gire el mando a posicin (llama pequea), reducindose as tambin el consumo de gas.
- Seleccin de temperatura
temperatura
Con el Selector de Temperatura, se puede graduar fcilmente la temperatura del agua girando
el selector hacia la derecha para obtener mayor temperatura, o hacia la izquierda para obtener agua
menos caliente.
- Servicio de Agua Caliente
- Una vez seleccionadas las prestaciones anteriores, el calentador realizar su proceso
de puesta en marcha; al abrir un grifo de agua caliente, automticamente se generar un haz
de chispas continuas a travs de su electrodo de ignicin, produciendo el encendido del
quemador directamente.
- Todos los modelos electrnicos disponen de una sonda de ionizacin, que quedar
sumergida en la llama y con ello controlando la misma.
- Si por alguna circunstancia se ha producido una incidencia en el circuito de gas, y la sonda no
captara presencia de llama, automticamente el electrodo de ignicin generara nuevamente su haz
de chispas durante unos segundos, para encender el quemador; en
caso de no encenderse el calentador quedar fuera de servicio.
- Debe eliminar la causa o elemento que impide la llegada de gas al calentador, por ejemplo cierre
involuntario de la llave de paso, bombona de gas agotada, etc.
NOTA IMPORTANTE
Para cuidar el medio ambiente deposite las pilas gastadas en los contenedores
disponibles para este fin.
PANEL DE MANDOS
CALENT
CALENTADORES 5, 10 LITROS
SELECTOR DE TEMPERATURA
MANDO DE GAS
MUY IMPORTANTE
Se recomienda cerrar la llave de paso de gas de la instalacin, cuando no se use
el aparato con frecuencia.
ACOPLADOR 80 a 100
102.5 +0,5 INT.
101,5 +0,5 INT.
4,5 +0,5
21
0,5
17
0,5
44
~45
MODELOS de 10 y 14 l/min
400 (14 L)
328 (10 L)
130 mm
220 (14 L)
170 (10 L)
660 (14 L)
560 (10 L)
650 (14 L)
550 (10 L)
(*)
220 (14 L)
168 (10 L)
(*)
INSTR
INSTRUCCIONES PARA EL INST
INSTALADOR
El calentador debe ser instalado por un profesional con CARN DE INSTALADOR DE GAS AUTORIZADO. El
buen funcionamiento de su calentador COINTRA depende, en gran medida, de
su CORRECTA instalacin.
Su labor resultar ms fcil si se atiene a las indicaciones siguientes:
2. TUBERIAS.
2.1. Realice las conducciones de agua caliente lo ms cortas posibles. Asle los tramos largos para
evitar prdidas de calor.
2.2. Deje los extremos de los tubos de agua fra (F) y agua caliente (C) donde indica
el dibujo. Evite estrangulaciones y codos innecesarios. Recomendamos utilice un dimetro
mnimo de tubera de 1/2"; en caso de dbil presin de agua, 3/4".
En la conduccin de agua caliente, evite que se puedan formar bolsas de aire. Purgue las
tuberas de agua.
2.3. Conecte al tubo de agua fra la llave de paso suministrada con el calentador, en
la bolsa de accesorios.
2.4. En la acometida de gas al calentador, intercale una llave adecuada de paso de gas.
2.4.1. La unin entre la citada llave de paso y el codo entrada gas al calentador entregado en la
bolsa de accesorios, se debe de realizar mediante soldadura fuerte.
2.4.2. Los dimetros de los tubos de conexin gas, deben ser:
- Tubo 12 mm exterior, para los modelos COB 5 y COB 5 x.
- Tubo 15 mm exterior, para los modelos COB 10, COB 10 x y COB 14.
2.5. Conexiones hidrulicas del calentador.
2.5.1. Para facilitar la instalacin o sustitucin con modelos anteriores, se ha equipado los
calentadores con latiguillos flexibles.
2.5.2. Conecte los flexibles segn la siguiente indicacin:
- Flexible Hembra-Hembra; sirve para conectar la entrada de agua fra y la entrada del
calentador.
- Flexible Macho-Hembra; sirve para conectar la salida de agua caliente y la red de
distribucin.
2.5.3. Todas las conexiones indicadas, se realizan en rosca R 1/2.
2.5.4. asegrese de la correcta estanquidad de las uniones realizadas.
C
F
Fra
Caliente
Gas
3. COLOCACIN.
- Para el correcto funcionamiento del calentador, es necesario instalar el mismo en posicin completamente
vertical.
- Utilice la plantilla de instalacin incluida en el embalaje. A modo de ejemplo, vase la plantilla del modelo
de 14 l/min:
110
110
5
220
ZEFIRO 14
OPTIMA
14
660
650
400
220
110
110
15
COLD
GAS
ENTRADA
HOT
ENTRADA
WATER
INLET SALIDA
WATER
AGUA FRIA
INLET
GAS
AGUA
OUTLET
CALIENTE
10
5. MONT
MONTAJE DE CUBIER
CUBIERTA.
Si por alguna razn necesita desmontar la cubierta para la instalacin:
5.1. Desmonte los mandos de gas y selector de temperatura, tirando de ellos.
5.2. Desenrosque los tornillos que une la cubierta.
5.3. Monte los mandos, presionando los mismos hacia dentro.
COMPROBACIN Y ENTREGA
- Asegrese que la instalacin realizada cumple TODOS LOS REQUISITOS DE LA NORMATIVA EN VIGOR DEL PAIS EN EL
QUE ESTE INSTALADO.
- Compruebe la absoluta estanquidad de los circuitos de agua y gas.
- Ponga en marcha el calentador y verifique su funcionamiento durante 15 min, ensee al usuario la correcta manipulacin y
uso del calentador y entrguele el presente manual de instrucciones.
11
MUY IMPOR
IMPORTANTE
No olvide practicar, en el local de ubicacin del calentador, la abertura de entrada de aire
y en su caso, de salida del aire, segn lo ordena el Reglamento de Instalaciones de GAS. Para
mantener limpio el Medio Ambiente, recuerde depositar las pilas o bateras
agotadas, en los contenedores dispuestos para la recogida de estos productos.
GAS
Qm
Qn
Qm
Qn
Qm
g/s
g/s
g/s
g/s
g/s
g/s
G20
7,5
6,3
16,1
12,5
21,5
16,3
G30
7,1
5,9
15,1
11,7
20,2
15,3
12
DATOS TCNICOS
5 LITROS
DATOS TCNICOS
COB 5
10 LITROS
COB 5 x
COB 10
14 LITROS
COB 10 x
COB 14
CATEGORA
II2H3+
II2H3+
II2H3+
II2H3+
II2H3+
B 11BS
B 11BS
B 11
B 11BS
B 11
Interior
Exterior
Interior
Exterior
Interior
4,10
10,1
4,10
10,1
8,10
20,2
8,10
20,2
10,70
26,8
3,6
8,9
3,6
8,9
7,10
17,8
7,10
17,8
9,3
23,8
5,1
5,1
10,1
10,1
13,7
2,6
2,6
5,1
5,1
6,8
0,5
0,5
0,5
0,5
0,2
0,2
0,2
0,2
0,2
10
10
10
10
10
0,32
0,32
0,63
0,63
0,84
kg/h
0,79
0,79
1,58
1,58
2,09
m3 /h
0,43
1,07
0,43
1,07
0,86
2,14
0,86
2,14
1,13
2,83
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
20
En el quemador- Potencia
mxima ( ) (mbar)
Butano G-30
Propano G-31
Natural G-20
27,3
35,3
14,7
27,3
35,3
14,7
27,57
35,84
13,33
27,57
35,84
13,33
En el quemador- Potencia
mnima ( ) (mbar)
Butano G-30
Propano G-31
Natural G-20
TIPO DE APARATO
TIPO DE INSTALACIN
CONSUMO NOMINAL kW minimo
Mximo
POTENCIA UTIL - kW
mnima
Mxima
(d)
0,4
Butano G-30
Gas natural G-20
PRESIN DE GAS (mbar)
no
no
0461CN0998
CONTRASENA CE
28-30
37
20
27,57
35,84
13,33
no
0461BT0927
13
PREVENCIONES
CONTRA LA CAL
En zonas con agua dura, para evitar la deposicin de cal que dificulte la trasnsmisin de calor, conviene reducir la temperatura
de utilizacin, gradundola con el mando selector.
CONTRA EL HIELO
En zonas fras para evitar que se dae el calentador ante una inminente helada:
- Cierre la llave de entrada de agua al calentador
- Abra el grifo de agua caliente ms bajo (p.e. el bid)
- Afloje la vlvula de drenaje en la parte inferior del calentador, para que salga el agua y pueda entrar aire.
CONSERVACIN
Para la limpieza de la cubierta utilice un pao con agua jabonosa, evite detergentes abrasivos y disolventes.
Para prolongar la vida de su calentador, debe ser revisado y limpiado anualmente, para lo cual avise al Servicio de Asistencia
Tcnica Cointra.
NOTA IMPORTANTE: El tornillo de regulacin de caudal mnimo, sito en el cuerpo de agua, que se
encuentra lacrado, no ser manipulado en ningn caso.
14
MODELOS
DIMETRO
CDIGO
INYECTORES
G.P.L.
0,66
G.N.
1,0
MODELOS 10 l/min.
COB 10 y COB 10 x
MODELOS
DIMETRO
CDIGO
INYECTORES
G.P.L.
0,72
G.N.
1,15
MODELO 14 l/min.
COB 14
MODELOS
INYECTORES
DIMETRO
CDIGO
G.P.L.
0,66
15
G.N.
1,02
SERVICIO DE ASISTENCIA
TECNICA DEL FABRICANTE
Ms de 120 puntos en toda Espaa.
Estamos a su disposicin en el telfono:
902
902 40 20 10
Sello/Firma de convalidacin
Para colocar por el S.A.T., el cdigo de barras
contenido en la documentacin del producto
Cdigo SAT
N de fabricacin
Fecha de instalacin
Tipo de gas
Domicilio
C.P.
N
Localidad
Tel.
Domicilio
Prov.
C.P.
Fax / Mvil
Tel.
COD.A73016501
COINTRA GODESIA
Avda. De Italia, 2. (Edificio Ferroli)
28820 Coslada (Madrid)
16
N
Localidad
Prov.
Fax / Mvil
Las posibles reclamaciones debern efectuarse ante el organismo competente en esta materia.
17
OPTIMA
CHAUFFECHAUFFE-EAU INSTANTAN GAZ
Instructions d'installation, d'utilisation et d'entretien
Nous vous flicitons pour l'acquisition de notre produit.
Le chauffe-eau instantan gaz COINTRA que vous avez choisi a t conu et fabriqu avec soin par nos spcialistes et il a t soigneusement
test afin de satisfaire toutes vos exigences.
Pour que vous puissiez obtenir un confort maximum en eau chaude sanitaire grce votre nouveau chauffe-eau instantan gaz COINTRA,
nous vous recommandons de lire avec attention les instructions suivantes.
Pour l'installation, l'utilisation et la conservation de l'appareil sera ncessaire de respecter les avertissements.
PAGES
ENSEMBLES FONCTIONNELS
Modles de 10 l /min
17,8 kW (255 Kcal/min)
Modele 14l/min
23,8 kW
(341 kcal/min)
COB 5
COB 5 x
COB 10
COB 10 x
COB 14
1. Coupe-tirage incorpor
Il assure une bonne combustion mme si le tirage varie dans le conduit
d'vacuation de gaz brls (chemine). Grce sa nouvelle configuration, le
couvercle du chauffe-eau ne possde pas de grilles.
oui
oui
oui
oui
oui
2. changeur de chaleur.
En cuivre lectrolytique pur avec revtement calorique qui assure la
transmission maximum de la chaleur l'eau.
oui
oui
oui
oui
oui
3. Brleur
Avec une technologie de pointe qui rentabilise au maximum le gaz consomm.
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
7. Slecteur de temprature.
Il sert graduer volont la temprature de l'eau chaude.
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
non
oui
non
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
oui
- PANNEAU DE COMMANDES
CHAUFFE--EAU 5 ET 10 LITRES
CHAUFFE
SLECTEUR DE TEMPRATURE.
COMMANDE DE GAZ
TRS IMPORTANT
Il est recommand de fermer le robinet de fermeture du gaz de l'installation si l'appareil n'est pas .
souvent utilis.
4,5 +0,5
21
0,5
17
0,5
44
minimum
MODLES de 10 l/min
400 (14 L)
328 (10 L)
130 mm
220 (14 L)
170 (10 L)
660 (14 L)
560 (10 L)
650 (14 L)
550 (10 L)
(*)
220 (14 L)
168 (10 L)
(*)
2.4. Dans le branchement du gaz au chauffe-eau, intercalez un robinet de fermeture de gaz appropri.
2.4.1. L'union entre le robinet de fermeture et le coude entre gaz et le chauffe-eau fourni dans le sachet des
accessoires, doit tre ralis au moyen d'une soudure forte.
2.4.2. Les diamtres des tuyaux de connexion gaz, doivent tre:
- Tuyau 12 mm extrieur, pour les modles COB 5 et COB 5 x.
- Tuyau 15 mm extrieur, pour les modles COB 10, COB 10 x et COB 14.
2.5. Connexion hydraulique du chauffe-eau.
2.5.1. Pour faciliter l'installation ou le remplacement de modles antrieurs, les chauffe-eau sont quips de
cbles flexibles.
2.5.2. Connectez les cbles flexibles en suivant les instructions suivantes :
- Flexible Femelle-Femelle; il sert connecter l'entre de l'eau froide l'entre du chauffe-eau.
-Flexible Mle-Femelle; il sert connecter la sortie d'eau chaude au rseau de distribution.
2.5.3. Toutes les connexions indiques, se feront avec une vis R 1/2.
2.5.4. Vrifiez la correcte tanchit des unions ralises.
C
F
F Froid
C Chaud
Gaz
3. POSITIONNEMENT
- Pour un fonctionnement correct de l'appareil de chauffage, installer le mme dans la position verticale.
- Utilisez le gabarit de montage inclus dans le forfait. A titre d'exemple, voir le modle modle de 14 l / min:
110
110
5
220
ZEFIRO 14
OPTIMA
14
660
650
400
220
110
110
15
GAS
INLET
Arrive
gaz
HOT
Sortie
WATER
OUTLET
d'eau
COLD
Arrive
WATER
INLET
d'eau
chaudeinclusfroide
- Les lments de fixation sont dans le sac d'accessoires
avec le (Et les chevilles de fixation suprieure et tire-fonds
de fixation infrieures)
- Suspendre l'appareil de crochets et serrez les tire-fonds pour fixer l'appareil au mur.
- Connectez les cbles flexibles d'eau chaude et d'eau froide sans oublier de vrifier l'tanchit. Ne retirez pas le filtre
l'entre de l'eau froide afin d'viter tout problme dans la circulation.
10
Modle de 14litres
Qn
Qm
Qn
Qm
Qn
Qm
g/s
g/s
g/s
g/s
g/s
g/s
G20
7,5
6,3
16,1
12,5
21,5
16,3
G30
7,1
5,9
15,1
11,7
20,2
15,3
GAZ
11
DONNES TCHNIQUES
5 LITRES
DONNES TECHNIQUES
COB 5
10 LITRES
COB 5 x
COB 10
14 LITRES
COB 10 x
COB 14
CATGORIES
II2H3+
TYPE D'APPAREIL
TYPE D'INSTALLATION
CONSOMMATION NOMINALE- KW minimum
maximum
minimum
PUISSANCE UTILE-KW
maximu
m
DBITS D'EAU (l/min) ET
TEMPRATURE : (a)
40 C (= 25 C)
65 C (= 50 C)
PRESSION D'EAU MINIMALE (bar)
POUR TEMPRATURE: (b)
40 C (= 25 C)
65 C (= 50 C)
PRESSION D'EAU MAXIMUM (bar)
(d)
II2H3+
II2H3+
II2H3+
II2H3+
B 11BS
B 11
B 11BS
B 11
B 11BS
Intrieur
Extrieur
Intrieur
Extrieur
Intrieur
4,10
10,1
4,10
10,1
8,10
20,2
8,10
20,2
10,70
26,8
3,6
8,9
3,6
8,9
7,10
17,8
7,10
17,8
9,3
23,8
5,1
5,1
10,1
10,1
13,7
2,6
2,6
5,1
5,1
6,8
0,5
0,5
0,5
0,5
0,2
0,2
0,2
0,2
0,2
10
10
10
10
10
0,4
0,32
0,32
0,63
0,63
0,84
Propane G-31
Butane G-30
kg/h
0,79
0,79
1,58
1,58
2,09
m3 /h
0,43
1,07
0,43
1,07
0,86
2,14
0,86
2,14
1,13
2,83
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
20
27,3
35,3
14,7
27,3
35,3
14,7
27,57
35,84
13,33
27,57
35,84
13,33
non
no
0461CN0998
CODE CE
12
28-30
37
20
27,57
35,84
13,33
non
0461BT0927
PRVEN
PRVENT
VENTIONS
CONTRE LA CHAUX
L o leau est dure, pour eviter que la chaux se dpose en rendant difficile la transmission de la chaleur, il est conseill de reduir la temperature
dutilisation de leau, en la rglant avec la commande du slecteur.
CONTRA LE GEL
Si le chauffe-bain est install dans un endroit froid, pour eviter avant une glee inminente que le chauffe-bain peut sabmer:
- Fermer le robinet deau lentre du chauffe-bain
- Ouvrir le robinet deau chaude l eplus bas (celui du bidet par exemple)
- Desserrer le bouchon de purge sur la partie infrieure du chauffe-bain, pour que lair puisse entrer et leau sortir.
CONSERVATIO
CONSERVATION
TION
Pour nettoyer lenveloppe, utilisez un chiffon avec de leau savonneuse, evitez les dtergents abarsifs y les dissolvants. Pour
prolonger la vie de le chauffe-bain, il est conseill de le faire rviser et de le nettoyer une fois par an, vous debez faire appel au
Service dAssistance Technique Cointra.
ADAPTATIO
ADAPTATION
TION AUX
AUX DIFF
DIFFRENTS
FFRENTS GAZ
GAZ
Le chauffe-bain est prepar pour un type spcifique de gaz. Adaptation d'un chauffe-bain COINTRA un gaz different de l'usine
a t prpar doit tre effectue par habilites, utilisant des pices d'origine COINTRA et conformment la rglementation en
vigueur dans le pays dans lequel l'appareil est install. Cette adaptation doit tre comme suit:
1.
2.
3.
4.
NOTE IMPORTANTE : La vis de rglage de dbit minimum, situe dans le corps d'eau, qui est scell
ne sera pas manipule en aucune manire.
13
MODLES
MODLES
DIAMTRE
CODE
INJECTEURS
G.P.L.
0,66
G.N.
1,0
MODLES 10 l/min
COB 10 et COB 10 x
MODLES
DIAMTRE
CODE
INJECTEURS
G.P.L.
0,72
G.N.
1,15
MODLE 14
14 l/min
COB 14
MODLES
INJECTEURS
DIAMTRE
CODE
G.P.L.
0,66
14
G.N.
1,02
SCHMA
OBSERVATION: Le respect de la totalit des donnes cites dans le Certificat de Garantie est obligatoire. La
OBSERVATION
validation de la garantie devra tre ralise immdiatement, en y reportant la date et en l'envoyant ensuite
COINTRA GODESIA
Tous nos Services Techniques OFFICIELS disposent de l' accrditation correspondante de la part de Cointra. Exigez
cette accrditation lors de chaque intervention.
15
OPTIMA
ESQUENTADOR INST
INS TANTNEO D E GUA
GU A A GS
Instrues de instalao, uso e conservao
NDICE
PG
PG.
CONJUNTOS FUNCIONAIS
Modelos de 10 l/min
17,8 kW (255 Kcal/min)
Modelo 14l/min
23,8 kW
(341 kcal/min)
COB 5
COB 5 x
COB 10
COB 10 x
COB 14
1. Cortatiros incorporado.
Assegura a correcta combusto embora varie a tiragem na conduta de
evacuao de gases queimados (chamin). Graas sua nova concepo, a
cobertura do esquentador est isenta de grelhas.
SIM
SIM
SIM
SIM
SIM
2. Permutador de calor.
De cobre electroltico puro, com revestimento calrico que assegura a
mxima transmisso de calor gua.
SIM
SIM
SIM
SIM
SIM
3. Queimador
De avanada tecnologia, que aproveita ao mximo o gs consumido.
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
6. Comando de gs frontal.
Serve tambm para SELECCIONAR MANUALMENTE A POTNCIA
DESEJADA.
SIM
SIM
SIM
SIM
SIM
7. Selector de temperatura.
Serve para regular a temperatura da gua quente.
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
No
SIM
No
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
SIM
INSTR
NSTRUES PARA O UTILIZADOR
ESQUENTADORES ELECTRNICOS (SEM PILOTO PERMANENTE)
- Verificaes prvias
1. Assegure-se que as torneiras de gua quente esto fechadas.
2. Abra a torneira de segurana de passagem do gs para o esquentador, situada na ligao de gs do aparelho.
3. Verifique se as pilhas (ou baterias) de 1,5 V esto inseridas no seu alojamento, com
a posio de polarizao correcta (+ e -), e se est retirada a fita de segurana.
4. Se as mesmas tm carga suficiente para o funcionamento do esquentador .
- Seleco manual da Potncia do Queimador
Para acender o aparelho rode o comando de gs da posio
para uma das 2 posies,
mnima ou mxima.
Com o comando de gs,podemos seleccionar a potncia do esquentador,mnima( ) ou mxima
( ), e posies intermdias conforme a intensidade do aquecimento da gua que deseje. Colocado o
comando de gs na posio
(chama grande), o aparelho aquece a gua em plena
potncia. Se a temperatura desta excessivamente elevada, por exemplo, no Vero
ou quando so necessrios pequenos caudais de gua no muito quente, rode o referido comando
para a posio
(chama pequena), reduzindo a potncia (e o consumo de gs) praticamente para metade.
- Seleco de temperatura
Com o Selector de Temperatura, pode graduar facilmente a temperatura da gua, rodando o selector para a direita
para obter maior temperatura ou para a esquerda para obter gua menos quente.
- Servio de gua Quente
- Uma vez seleccionadas as prestaes anteriores, o esquentador realizar o seu processo
de entrada em funcionamento; ao abrir uma torneira de gua quente, sero geradas automaticamente fascas
contnuas atravs do seu elctrodo de ignio, produzindo o acender do queimador directamente.
- Todos os modelos electrnicos dispem de uma sonda de ionizao, que ficar submersa na
chama e, deste modo, controla-a.
- Se, por alguma circunstncia, ocorreu uma incidncia no circuito de gs, e a sonda no capta a
presena de chama, o elctrodo de ignio activaria automaticamente de novo o seu isqueiro durante
uns segundos, para acender o queimador; no caso de no acender, o esquentador ficar fora de
servio.
- Deve eliminar a causa ou elemento que impede a chegada de gs ao esquentador como, por
exemplo, fecho involuntrio da torneira de segurana, bilha de gs vazia, etc.
NOTA IMPORTANTE
PAINEL
AINEL DE COMANDOS
COMANDOS
ESQUENTADORES 5 e 10 LITROS
SELECTOR DE TEMPERATURA
COMANDO DE GS
MUITO IMPORTANTE
Recomenda-se fechar a torneira de segurana do gs da instalao quando no
se usar o aparelho com frequncia.
0,5
17
0,5
44
~45
MODELOS de 10 l/min
400 (14 L)
328 (10 L)
130 mm
220 (14 L)
170 (10 L)
660 (14 L)
560 (10 L)
650 (14 L)
550 (10 L)
(*)
220 (14 L)
168 (10 L)
(*)
2. TUBAGENS.
2.1. Faa as condutas de gua quente o mais curtas possveis. Isole os tramos largos para evitar perdas
de calor.
2.2. Deixe os extremos dos tubos de gua fria (F) e gua quente (C) onde indica
o esquema. Evite estrangulamentos e cotovelos desnecessrios. Recomendamos que
utilize um dimetro mnimo de tubagem de 1/2"; 3/4" em caso de presso dbil de gua.
Nas condutas de gua quente, evite que se possam formar bolsas de ar. Purgue as tubagens
de gua.
2.3. Ligue ao tubo de gua fria a torneira de segurana fornecida com o esquentador, na
bolsa de acessrios.
C
F
Fria
Quente
Gs
3. COLOCAO.
- Para o funcionamento correcto do aquecedor, instalar o mesmo na posio de cheio na posio vertical.
- Use o modelo de montagem includo no pacote. Como exemplo, veja o modelo modelo de 14 l / min:
110
110
5
220
ZEFIRO 14
OPTIMA
14
660
650
400
220
110
110
15
Verifique
Sada de
gs. GAS
gua
HOT
INLET
WATER
quente.
OUTLET
Entrada de
fria.
gua
COLD
WATER
INLET
- Os elementos de fixao esto no saco de acessrios includo com o (E buchas para fixao superior e
parafusos de fixao mais baixos)
- Pendure o aparelho de anzis e apertar os parafusos para prender a unidade para a parede.
- Ligue os tubos flexveis de gua quente e fria sem esquecer de verificar a estanqueidade. No
retire o filtro na entrada de gua fria para evitar problemas na circulao.
5. MONTAGEM DA COBERTURA.
Se por alguma razo necessita desmontar a cobertura para a instalao:
5.1. Desmonte os comandos de gs e selector de temperatura, puxando-os.
5.2. Desenrosque os parafusos que unem a cobertura.
5.3. Monte os comandos, pressionando-os para dentro.
TESTES E ENTREGA
- Certifique-se que a instalao se rene todos os requisitos dos regulamentos em vigor no pas em que tal
INSTALADO.
- Verificar a vedao completa dos circuitos de gs e gua.
- Ligue o aquecedor e verificar o seu funcionamento por 15 minutos, ensina o usurio a manipulao e uso
de aquecedor e dar a este manual de instrues.
10
6. DISPOSITIVO
DISPOSITIVO DE CONTROLO DE EVACUAO DE GASES (T.T.B.)
6.1. O elemento de segurana T.T.B. que equipa os esquentadores garante a correcta evacuao
dos produtos da combusto; por isso, o seu funcionamento no deve ser eliminado nem
devem ser efectuadas intervenes no controladas sobre o mesmo.
Em caso de distrbios na evacuao dos produtos de combusto, o dispositivo interrompe o fornecimento de
gs ao queimador.
6.2. Se, ao iniciar o funcionamento do esquentador, o dispositivo T.T.B. actua, reveja a sada dos gases
queimados, verificando a evacuao com um espelho arrefecido com gua corrente, ou com
qualquer aparelho de medida homologado para tal finalidade.
6.3. Em caso de avaria, utilize exclusivamente peas de substituio originais, porque, em
caso contrrio, o funcionamento do dispositivo T.T.B. pode ser incorrecto.
6.4. A substituio do dispositivo T.T.B. deve ser realizada por tcnicos especialistas procedendo da
seguinte forma:
- Desmontar o dispositivo T.T.B. defeituoso, soltando os dois parafusos que o fixam.
- Desmontar o termopar.
- Colocar um novo termopar original.
- Fixar o dispositivo T.T.B. caixa de fumos sem forar os parafusos.
- Comprovar o seu correcto funcionamento.
6.5. Os modelos de Instalao exclusivamente no exterior no precisam deste dispositivo.
MUITO IMPOR
IMPORTANTE
No se esquea de experimentar, no local de localizao do esquentador, a abertura da
entrada de ar e, se for o caso, a sada de ar, conforme indica o Regulamento de Instalaes de
GS. Para manter limpo o Meio Ambiente, lembre-se de que deve depositar as pilhas ou baterias
vazias nos contentores dispostos para a recolha destes produtos.
GS
Qm
Qn
Qm
Qn
Qm
g/s
g/s
g/s
g/s
g/s
g/s
G20
7,5
6,3
16,1
12,5
21,5
16,3
G30
7,1
5,9
15,1
11,7
20,2
15,3
11
DADOS TCNICOS
5 LITROS
DADOS TCNICOS
COB 5
10 LITROS
COB 5 x
COB 10
14 LITROS
COB 10 x
COB 14
CATEGORIA
II2H3+
TIPO DE APARELHO
TIPO DE INSTALAO
CONSUMO NOMINAL kW min.
Max.
POTNCIA TIL - kW
Mnima
Mxima
II2H3+
II2H3+
II2H3+
II2H3+
B 11BS
B 11BS
B 11
B 11BS
B 11
Interior
Exterior
Interior
Exterior
4,10
10,1
4,10
10,1
8,10
20,2
8,10
20,2
3,6
8,9
3,6
8,9
7,10
17,8
7,10
17,8
9,3
23,8
5,1
5,1
10,1
10,1
13,7
2,6
2,6
5,1
5,1
6,8
0,5
0,5
0,5
0,5
0,2
0,2
0,2
0,2
0,2
10
10
10
10
10
Interior
10,70
26,8
0,4
0,32
0,32
0,63
0,63
0,84
Propano G-31
Butano G-30
kg/h
0,79
0,79
1,58
1,58
2,09
Gs natural G-20
m3 /h
0,43
1,07
0,43
1,07
0,86
2,14
0,86
2,14
1,13
2,83
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
20
No queimador- Potncia
mxima ( ) (mbar)
Butano G-30
Propano G-31
Natural G-20
27,3
35,3
14,7
27,3
35,3
14,7
27,57
35,84
13,33
27,57
35,84
13,33
No queimador- Potncia
mnima ( ) (mbar)
Butano G-30
Propano G-31
Natural G-20
PRESSO DE GS (mbar)
No
no
0461CN0998
CDIGO CE
28-30
37
20
27,57
35,84
13,33
No
0461BT0927
12
PREVENES
CONTRA O CALCRIO
Onde a agua dura, o calcrio deposita-senas paredes, dificultando a transmisso de calor. Para o evitar convm limitar
temperatura de utilizao a gua, regulando-o com o comando do selector.
CONTRA O GELO
Se o seu esquentador est insatlado num lugar frio,para evitar perante uma geada eminente a gua pode congelar e danificlo, faa o seguinte:
- Feche a vlvula da gua entradad do esquentador
- Abra a torneira de gua quente mais baixa (p.e. no bid)
- Afrouxe a tampa de purga na parte inferior do esquentador para que possa entrarar e saia a agua pela torneira.
CONSERVAAO
CONSERVAAO
Para limpeza da cobertura utilize um pano com gua e detergente, no utilize detergentes abrasivos, nem disolventes.
conveniente, para prolongar a vida do seu esquentador, fazer a reviso e limp-lo uma vez por ano, deve contactar o Servio de
AssistnciaTcnica Oficial da Cointra.
ADAPTA
ADAPTAAO AOS DIVERSOS GASES
O esquentador est configurado para um tipo especfico de gs. Adaptao de esquentedores Cointra a gs diferentes das de
fbrica foi preparado deve ser realizado pelas autoridades competentes autorizado o uso de peas originais Cointra e em
conformidade com os regulamentos em vigor no pas em que o aparelho instalado. Esta adaptao deve ser a seguinte:
1.
NOTA IMPORTANTE: O parafuso de ajuste de fluxo mnimo, situado no corpo de gua, que selado
no ir ser manipulado de forma alguma.
13
MODELOS
DIMETRO
CDIGO
INJECTORES
G.P.L.
0,66
G.N.
1,0
COB 10 e COB 10 E x
G.P.L.
0,72
G.N.
1,15
COB 14
G.P.L.
0,66
G.N.
1,02
MODELOS 10 l/min.
MODELOS
INJECTORES
DIMETRO
CDIGO
MODELO 14 l/min.
MODELOS
INJECTORES
DIMETRO
CDIGO
14
As eventuais reclamaes devem ser efectuadas perante o organismo competente nesta matria.
15
OPTIMA
:
COB 5
COB 10
COB 5 x
COB 10 x
.
.
.
.
3................................................................
4............................................................................................
) (5........... ........................................................
5..................................................................................
5.......................................................................
5...............................................................................
5..................................................................................
6................................................................................
6..................................................................................
7........................................................................................
8..........................................................................
8...............................................................................................
10.............................................................................................
11.........................................................................
11......................................................................................
11..................................................................................
12...............................................................
13......................................................................................
14.............................................................................
14........................................................
1
.
) (
5
/
89 )1275
/(
5/
COB 14
89 ) 1275
/(
COB10
COB10x
COB5 COB5
.1 .
)( .
.
.2
.3
.
.5
.6 .
.
.7
.9
.
.
.
.13 :
.14 .
.
) (.13
.15 .
)
(.13
.16
.17
.18 ) . (
.19
.20
.21
) ( .
.1 .
.2 .
.3 15 ) + (
.
.4 .
)( ) (+
.
.
) ( .
.
.
.
.
.
4
.
. .
.
5 10.
5 /
80 100
100
=1 :2./1
=3 : . 2/1
=2 / 12 :
15 :
10 /
)400 (14 L
)328 (10 L
)220 (14 L
)170 (10 L
130 mm
)660 (14 L
)560 (10 L
)650 (14 L
)550 (10 L
)*(
)*(
=1 :2./1
=3 : . 2/1
=2 / 12 :
15 :
)220 (14 L
)168 (10 L
.
:
.1
1.1
.
) (.
) (12
1.2
1.3
.
.
.2
2.1 .
.
2.2 )( )( .
. "2/1
."4/3
2.3 .
2.4 .
2.4.1
.
2.4.2 :
12 COB 5 y COB 5 x
15 COB 14COB 10, COB 10x
2.5
2.5.1 .
2.5.2 :
.
.
2.5.3 R 1/2
2.5.4 .
.3
. . 14 /:110
110
5
220
ZEFIRO 14
OPTIMA
14
660
650
400
220
110
110
15
COLD
Arrive
WATER
INLET
d'eau
froide
HOT
Sortie
WATER
OUTLET
d'eau
GAS
INLET
Arriv
e gaz
chaude
-
) (
.
.
.4
4.1 .
:
COB 5 y COB 5 x
.
80
.
: 100
. 80 100
. 80 .
100 .
. COB 10 y COB 10x
11 ..
12 ..
.
. COB 14
130 mm
4.2 .11
4.3 .
.
4.4
. .
.5
:
5.1 .
5.2 .
5.3 .
. . 15
.-
10
.6 ) (
6.1
.
.
6.2
.
6.3
.
6.4 :
.
.
.
.
.
6.5 .
.
.
.. )(UNE-EN 26 5.2.1.4. b
10
10
Qm
Qn
Qm
Qn
Qm
Qn
g/s
g/s
g/s
g/s
g/s
g/s
16,3
21,5
12,5
16,1
6,3
7,5
G20
15,3
20,2
11,7
15,1
5,9
7,1
G30
.
11
14
10
COB 14
COB 10 x
II2H3+
II2H3+
II2H3+
B 11BS
B 11
B 11BS
COB 10
COB 5 x
COB 5
II2H3+
II2H3+
B 11
B 11BS
10,70
26,8
8,10
20,2
8,10
20,2
4,10
10,1
4,10
10,1
9,3
23,8
7,10
17,8
7,10
17,8
3,6
8,9
3,6
8,9
10,1
10,1
5,1
5,1
5,1
5,1
2,6
2,6
)65 C (= 50 C
0,5
0,5
0,5
0,5
)(bar
)(b
)40 C (= 25 C
0,2
0,2
0,2
0,2
0,2
)65 C (= 50 C
10
10
10
10
10
)(d) (bar
0,84
0,63
0,63
0,32
0,32
2,09
1,58
1,58
0,79
0,79
1,13
2,83
0,86
2,14
0,86
2,14
0,43
1,07
0,43
1,07
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
20
27,57
35,84
13,33
27,57
35,84
13,33
27,3
35,3
14,7
27,3
35,3
14,7
)(mbar
G-30
G-31
G-20
) (220V50 Hz
13,7
6,8
0,4
) /(
:
)(a) 40 C (= 25 C
) (1013 mbar/288 K) (c
G-31
kg/h
G-30
m3 /h
G-20
)(mbar
28-30
37
20
27,57
35,84
13,33
0461BT0927
CE
0461CN0998
15 (a) .
(b) .
84 (c) PCI.
(d 75
12
5/
COB 5 y COB 5 x
G.P.L.
G.N.
1,0
0,66
10/
COB 10 y COB 10
G.N.
G.P.L.
1,15
0,72
14 l
COB 14
G.P.L.
G.N.
1,02
0,66
.
.
M.G.
LIM
B
TTB
C1
L.E.
M.A.
L.B.
= LIM
= B
= M.G.
= M.A.
Electr. encend. =.
= Electr. ioniz.
= TTB
13
2003/23
.
.
)(
.
.
:
.
.
.
.
:
.
/
.
.
.
.
) (.
.
.
) (
.
.
: .
.
. .
.
14
OPTIMA
INSTANTANEOUS
INSTANT ANEOUS GAS WATER HEATER
Installation, use and maintenance instructions
Congratulations on purchasing our product.
The COINTRA instant gas water heater that you have chosen has been carefully designed and manufactured by our
specialists and thoroughly checked to meet all your requirements.
We recommend that you read these instructions carefully for you to get maximum hot water comfort with your new
COINTRA instant gas water heater.
For installation, use and conservation of the gas water heater will be necessary to respect the warnings.
CONTENTS
PAGE
PAGE
DEPENDING ON THE MODEL CHOSEN, THE WATER HEATER WILL COMPRISE THE
FOLLOWING COMPONENTS
5 l/min models
8.9 kW (127.5 Kcal/min)
FUNCTIONAL ASSEMBLIES
COB 5
1. Incorporated draught diverter.
Ensures proper combustion even when the draught changes in the burnt gas
evacuation duct (flue). With its new design, the heater cover is free of gratings.
Yes
COB 5 x
10 l/min models
17.8 kW (255 Kcal/min)
COB 10
COB 10 x
Yes
Yes
Yes
14l/min model
23,8 kW
(341 kcal/min)
COB 14
Yes
2. Heat exchanger.
Pure electrolytic copper with a caloric coating that ensures the highest
possible heat transfer to water.
Yes
Yes
Yes
Yes
Yes
3. Burner
Advanced technology that takes full advantage of the gas consumed
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
no
Yes
no
Yes
Yes
Yes
Yes
Yes
Yes
20 . Drainage valve.
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
USER INSTRUCTIONS
ELECTRONIC
ELECTRONIC WATER HEATERS (WITHOUT PERMANENT PILOT LIGHT)
- Prior checks
1. Make sure hot water taps are turned off.
2. Turn on the gas to water heater stopcock that is located where gas is supplied to the appliance.
3. Check that the 1.5 V batteries are correctly installed according to polarity (+ and -) and the safety seal has been
removed.
4. Check that they are sufficiently charged for the water heater to function.
- Manual selection of Burner Power
To ignite the appliance, turn the gas knob from the position
to one of the 2 minimum or
maximum positions.
The gas knob allows you to select the water heater power, minimum ( ) or maximum
( ), and intermediate positions according to the hot water intensity required. Turn the gas knob to
the
position (large flame), the unit heats the water at full
power. If the temperature is too high, for example in summer or if a small volume of not very hot
water is required, turn the knob to the position (small flame), reducing the power (and gas
consumption) almost by half.
- Temperature selection
With the Temperature Selector you can easily gauge the water temperature by turning the selector to the right to
achieve a higher temperature, or to the left to obtain less hot water.
- Hot Water Service
- Once the previous settings have been selected, the water heater will start the process; turning on the hot water tap
will automatically generate continuous sparks through its ignition electrode and directly light the burner.
- All the electronic models have an ionisation probe, which is immersed in the flame to control
it.
- If for any reason an issue has occurred in the gas circuit and the probe does not detect the flames
presence, the ignition electrode will automatically generate sparks for a few seconds to ignite the
burner; in the event that the water heater does not turn on, it will be out of service.
- You must remove the cause or element that prevents the gas from reaching the water heater, for
example if the stopcock has been inadvertently turned off, worn out gas cylinder, etc.
- The water heater block is deactivated by turning on and off the hot water tap;
- If the cause is removed and the hot water supply is not re-established after turning on the hot water, repeat the
operation. Contact Technical Support if the anomaly persists.
- The flames presence in the burner is seen through the window on the cover.
- Turning off the water heater
To turn the water heater off, turn the gas knob again to the position
IMPORTANT NOTE
To protect the environment, deposit used batteries in containers intended for this
purpose.
CONTROL PANEL OF
5- AND 1010-LITRE WATER HEATERS
TEMPERATURE SELECTOR
GAS KNOB
VERY IMPORTANT
It is recommended that the installations stopcock is turned off when the unit is not being
used frequently.
5-l/min MODELS
WATER HEATERS WITHOUT PILOT LIGHT
COUPLER 80 to 100
102.5 +0,5 INT.
101,5 +0,5 INT.
4,5 +0,5
21
0,5
17
0,5
44
~45
10-l/min MODELS
400 (14 L)
328 (10 L)
130 mm
220 (14 L)
170 (10 L)
660 (14 L)
560 (10 L)
650 (14 L)
550 (10 L)
(*)
220 (14 L)
168 (10 L)
(*)
INSTALLATION INSTRUCTIONS
The water heater must be installed by a professional that holds an AUTHORISED GAS INSTALLER PERMIT. The smooth
operation of your COINTRA water heater depends largely on it being installed CORRECTLY.
This task will be easier if you follow the guidelines below:
2. PIPES.
2.1. Make the hot water pipes as short as possible. Isolate long sections to avoid heat loss.
2.2. Leave the ends of the cold water (F) and hot water (C) pipes as shown in the diagram. Avoid unnecessary bends and
bottlenecks. We recommend using a minimum diameter of piping of and in the case of low water pressure. Make sure air
pockets are unable to form in the hot water conduit. Flush water pipes.
2.3. Connect the stopcock, which was supplied with the water heater in the accessories bag, to the hot water pipe.
2.4. Insert a suitable gas stop cock in the gas supply to the water heater.
2.4.1. The joining between this stopcock and the gas entry tube to the water heater included in the
accessories bag must be carried out by brazing.
2.4.2. The gas connection pipes must have the following diameters:
- External 12 mm pipe for models COB 5 and COB 5 x.
- External 15 mm pipe, for models COB 10, COB 10 x and COB 14
2.5. Water heater water connections.
2.5.1. To make installation easier or replace previous models, the water heaters have been equipped
with flexible hoses.
2.5.2. Connect the flexible hoses according to the following directions:
- Female-Female flexible hose is used to connect the cold water inlet with the water heater inlet.
- Male-Female flexible hose is used to connect the hot water inlet with the water mains.
2.5.3. All connections shown are carried out with R 1/2 screw.
2.5.4. Make sure the joints are tightened properly.
H
C
Cold
Hot
Gas
3. POSITIONING.
- For correct operation of the heater, install it in a vertical position.
- Use the mounting template included in the package. As an example, see template model 14 l / min:
110
110
5
220
ZEFIRO 14
OPTIMA
14
660
650
400
220
110
110
15
Gas
inlet
GAS
INLET
HOT
Hot
WATER
OUTLET
water
COLD
Clod
WATER
INLET
water
10
GAS
14-litre Models
Qn
Qm
Qn
Qm
Qn
Qm
g/s
g/s
g/s
g/s
g/s
g/s
G20
7,5
6,3
16,1
12,5
21,5
16,3
G30
7,1
5,9
15,1
11,7
20,2
15,3
11
TECHNICAL SPECIFICATIONS
5 LITRES
TECHNICAL SPECIFICATIONS
10 LITRES
COB 5 x
CATEGORY
II2H3+
II2H3+
II2H3+
II2H3+
II2H3+
APPLIANCE TYPE
B 11BS
B 11
B 11BS
B 11
B 11BS
Inside
Outside
Inside
Outside
Inside
4,10
10.1
4,10
10.1
8,10
20.2
8,102
0.2
10,70
26,8
3,6
8.9
3,6
8.9
7,10
17.8
7,101
7.8
9,3
23,8
5.1
5.1
10.1
10.1
13,7
2.6
2.6
5.1
5.1
6,8
0.5
0.5
0.5
0.5
0.2
0.2
0.2
0.2
0,2
10
10
10
10
10
TYPE OF INSTALLATION
NOMINAL CONSUMPTION kW min.
USEFUL POWER - kW
Max.
minimum
maximum
(d)
COB 10
14 LITRES
COB 5
COB 10 x
COB 14
0,4
0.32
0.32
0.63
0.63
0,84
kg/h
0.79
0.79
1.58
1.58
2,09
m3 /h
0.43
1.07
0.43
1.07
0.86
2.14
0.86
2.14
1,13
2,83
28-30
37
20
28-30
37
20
28-30
37
20
28-30
37
20
27.3
35.3
14.7
27.3
35.3
14.7
27.57
35.84
13.33
27.57
35.84
13.33
no
no
no
no
Propane G-31
Butane G-30
Natural gas G-20
GAS PRESSURE (mbar)
EC MARK
0461CN0998
12
28-30
37
20
27,57
35,84
13,33
no
0461BT0927
PREVENTIONS
PREVENTIONS
AGAINST LIME
In specific areas with hard water, in order to prevent the deposition of lime that can affect to the heat trasnmission, it is
recommended to limit the output temperature adjusting it by means of the temperature selector.
AGAINST ICE
In specific cold areas, to prevent the water haeter from being damaged as result of an inminent freeze:
- Close the water inlet valve to the heater
- Open the lowest hot water tap (e.g. the bidet)
- Open the drain valve in the lower part of the heater, so that water can come out and the air can enter.
MAINTENANCE
Use a cloth with soapy water to clean the front cover, avoid abarsive detergents and solvents. To increase the life of your water
heater, it should be maintained and cleaned once a year, please call our Technical Service.
Turn off the water and gas supply, remove the knobs and put off the front cover.
Replace the injector nozzles (see figure A) in the burner by those specific for the corresponding gas.
Replace the gas front valve mechanism (figure B), paying attention to mount it correctly..
Place the new technical data sticker on the previous one, to show the right gas adaption.
A
VERY IMPORTANT: The adjusting screw of minimum flow, situated in the body of water, which is
sealed will not be manipulated in any way.
13
MODELS
DIAMETER
CODE
INJECTORS
G.P.L.
0.66
G.N.
1.0
10 l/min MODELS.
COB 10 and COB10 x
MODELS
DIAMETER
CODE
INJECTORS
G.P.L.
0.72
G.N.
1.15
14 l/min MODELS.
COB 14
MODELS
INJECTORS
DIAMETER
CODE
G.P.L.
0.66
14
G.N.
1.02
15
16