Académique Documents
Professionnel Documents
Culture Documents
PRELIMINARY
Title page
Alcatel-Lucent
Remote Radio Head 2X60W - 850, 1900 MHz
Maintenance Guide
3MN-01477-0004-REZZA
Issue 0.02 | January 2014
PRELIMINARY
Alcatel-Lucent Proprietary
Use pursuant to applicable agreements
PRELIMINARY
PRELIMINARY
Alcatel, Lucent, Alcatel-Lucent and the Alcatel-Lucent logo are trademarks of Alcatel-Lucent. All other trademarks are the property of their respective
owners.
The information presented is subject to change without notice. Alcatel-Lucent assumes no responsibility for inaccuracies contained herein.
Copyright 2014 Alcatel-Lucent. All rights reserved.
Contains proprietary/trade secret information which is the property of Alcatel-Lucent and must not be made available to, or copied or used by anyone outside
Alcatel-Lucent without its written authorization.
Not to be used or disclosed except in accordance with applicable agreements.
Alcatel-Lucent Proprietary
Use pursuant to applicable agreements
............................................................................................................................................................................................. xi
xi
........................................................................................................................................................................ xi
xi
Intended audience
....................................................................................................................................................................... xii
xii
Supported systems
...................................................................................................................................................................... xii
xii
PRELIMINARY
Contents
........................................................................................................................................................ xii
xii
...................................................................................................................................................................... xii
xii
.................................................................................................................................................................................. xii
xii
Conventions used
........................................................................................................................................................................ xii
xii
....................................................................................................................................................................... xv
xv
Safety statements
Overview ...................................................................................................................................................................................... 1-1
1-1
Structure of safety statements ............................................................................................................................................... 1-2
1-2
Preventive maintenance
Overview ...................................................................................................................................................................................... 2-1
2-1
Preventive maintenance activity .......................................................................................................................................... 2-2
2-2
Corrective maintenance
Overview ...................................................................................................................................................................................... 3-1
3-1
Corrective maintenance
......................................................................................................................................................... 3-2
3-2
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
iii
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Contents
....................................................................................................................................................................................................................................
Introduction
Overview ...................................................................................................................................................................................... 4-1
4-1
RRH 2X60W solution ............................................................................................................................................................. 4-2
4-2
Hardware description
Overview ...................................................................................................................................................................................... 5-1
5-1
RRH 2X60-1900/1900A hardware description .............................................................................................................. 5-2
5-2
RRH 2X60-850 and hardware description
...................................................................................................................... 5-7
5-7
...................................................................................................... 5-11
5-11
PRELIMINARY
.............................................................................................................. A-2
A-2
........................................................................................................................ A-7
A-7
.............................................................................................................................................................. A-8
A-8
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
iv
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
v
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Contents
PRELIMINARY
PRELIMINARY
Contents
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
vi
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
.................................................................................................... xi
3-1
PRELIMINARY
List of tables
............................................................................................................................... 3-2
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
vii
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
List of tables
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
viii
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
4-1
............................................................................. 4-2
5-1
5-2
5-3
5-4
5-5
7-1
....................................................................................... 5-2
PRELIMINARY
List of figures
......................................................................................... 5-7
............................................................................................................. 5-8
................................................................................................................................ 7-5
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
ix
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
List of figures
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
x
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Purpose
The purpose of this document is to describe the preventive and corrective procedures
applicable to the following Alcatel-Lucent Remote Radio Head variants:
The reissue history for issue 0.02 is shown in the following table:
Table 1
Location
Change
Related information
The reissue history for issue 0.01 is shown in the following table:
Table 2
Location
Change
None
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
xi
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Intended audience
No specific recommendation applies regarding the way readers should read this
document.It applies to the AT&T dedicated products and configuration WCDMA with
9396 d2U or d4U OneBTS.
Safety information
For your safety, this document contains safety statements. Safety statements are given at
points where risks of damage to personnel, equipment, and operation may exist. Failure to
follow the directions in a safety statement may result in serious consequences.
Prerequisites
Alcatel-Lucent Remote Radio Head 2X60W - 850, 1900 MHz for W-CDMA Technical Description, 3MN-01477-0003-DEZZA
Conventions used
Vocabulary conventions
RRH
Typographical conventions
PRELIMINARY
Description
Italicized text
Emphasized information
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
xii
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
Appearance
Description
Related information
PRELIMINARY
For information on subjects related to the content of this document, refer to the
documents listed in the following table:
For information on subjects related to the content of this document, refer to the
documents listed in the following table:
At this location
http://support.alcatel-lucent.
com.
RRH2x
Alcatel-Lucent W-CDMA
System - Safety Guide,
9YZ-04088-0007-TQZZA
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
RRH configurations
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
RRH installation
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
xiii
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
PRELIMINARY
At this location
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
Fault management
http://support.alcatel-lucent.
com.
W-CDMA Remote
Maintenance Tool Online
Help
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
http://support.alcatel-lucent.
com.
Installation of lightning
protection systems
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
xiv
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
At this location
Recommended Practices on
Surge Voltages in Low Voltage
AC Power Circuits, IEEE
C62.41 (Latest Edition)
http://support.alcatel-lucent.
com.
Power
PRELIMINARY
Document support
For support in using this or any other Alcatel-Lucent document, contact Alcatel-Lucent at
one of the following telephone numbers:
Technical support
For technical support, contact your local Alcatel-Lucent customer support team. See the
Alcatel-Lucent Support web site (http://www.alcatel-lucent.com/support/) for contact
information.
How to order
To order Alcatel-Lucent documents, contact your local sales representative or use Online
Customer Support (OLCS) (http://support.alcatel-lucent.com)
How to comment
To comment on this document, go to the Online Comment Form (http://infodoc.alcatellucent.com/comments/) or e-mail your comments to the Comments Hotline
(comments@alcatel-lucent.com).
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
xv
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
xvi
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Safety statements
1
Overview
Purpose
This chapter provides information on the structure of safety statements which may arise
in the course of your work.
Contents
Structure of safety statements
1-2
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
1-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Safety statements
....................................................................................................................................................................................................................................
This topic describes the components of safety statements that appear in this document.
General structure
E
L
MP
CAUTION
Lifting hazard
SA
PRELIMINARY
F
G
H
Item
Structure element
Purpose
Safety symbol
Signal word
Hazard type
Safety message
Avoidance message
Identifier
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
1-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
Signal words
Meaning
DANGER
WARNING
CAUTION
NOTICE
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
1-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Safety statements
PRELIMINARY
PRELIMINARY
Safety statements
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
1-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Preventive maintenance
2
Overview
Purpose
This chapter describes the preventive maintenance activity applicable to the RRH
2X60W.
Contents
Preventive maintenance activity
2-2
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
2-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Preventive maintenance
....................................................................................................................................................................................................................................
The preventive maintenance is used to periodically test the items of equipment that do not
directly trigger any alarm at the WMS. However, the execution of preventive maintenance
procedures can trigger alarms at the WMS.
These procedures must be performed according to the following schedules.
It is possible to group some of the procedures, which reduces the intervention time. The
intervention time indicated corresponds to the intervention time for each item of
equipment.
Note: In certain environments, these procedures may be required more frequently:
Systems located in high seismic areas may require anchor bolts and mounting
hardware to be tightened periodically especially for field installed items.
Connectors may require periodic cleaning in dirty and high humidity areas.
Periodicity
Test duration
(approx.)
10 minutes
10 minutes
WARNING
Personal injury hazard
PRELIMINARY
The personnel working on the cabinet must be authorized to work according to the
applicable safety standards
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
2-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
PRELIMINARY
Preventive maintenance
Title
Main body with following information:
Intervention time
Tools required
Step-by-step actions
One or more figures to help you execute the actions
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
2-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Preventive maintenance
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
2-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Corrective maintenance
3
Overview
Purpose
This chapter describes the corrective maintenance activity applicable to the RRH 2X60W.
Contents
Corrective maintenance
3-2
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
3-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Corrective maintenance
Corrective maintenance
....................................................................................................................................................................................................................................
Corrective maintenance
Corrective maintenance activity
The network maintenance is based on the supervision of the network, by using the OAM
graphical interface. For more information, see Alcatel-Lucent 9353 Wireless Management
System - User Guide, 9YZ-04088-0014-PCZZA.
It is also based on the identification and replacement of faulty items of equipment, using
the alarms.
The process consists of two steps:
1. Locating and identifying the faulty RRH 2X60W through alarms at the WMS. See
"Fault management" chapter in Alcatel-Lucent 9353 Wireless Management System User Guide, 9YZ-04088-0014-PCZZA.
2. Replacing the faulty RRH 2X60W following the replacement procedure detailed in
this publication.
RRH 2X60W replacement
In the case of the RRH 2X60W, no separate module replacement exists: the whole RRH
2X60W is to be replaced. The procedure is detailed in Replacing an RRH 2X60W
(p. 8-2).
The following table indicates the orderable item (code) for each module or item to be
replaced from the RRH 2X60W variants.
PRELIMINARY
Table 3-1
RRH 2X60W
module/item
Orderable item
Provisioning rule
1AB187280063
1AB194670019
1AB187280065
849138136
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
3-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
Corrective maintenance
....................................................................................................................................................................................................................................
Title
Main body with the following information:
Intervention time
Tools required
Impact of the procedure, if necessary
PRELIMINARY
Corrective maintenance
Step-by-step actions
One or more figures are provided to help you execute the actions.
Intervention restrictions
There may be a lapse of time between the identification of the alarm at the Access OAM
Graphic User Interface (GUI) and the time you arrive at the site.
You must be synchronized with the access network controller or system administrator (by
telephone) before an on-site intervention, in the following cases:
Isolating procedures
Completion of an on-site intervention
Return to service procedure
The personnel must obey the safety instructions specific to the installation site:
Rules concerning the premises (see instructions posted on site or in the building)
Rules linked to general personnel safety instructions
The personnel working on the cabinet must be authorized to work according to security
standards.
Equipment safety instructions
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
3-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Corrective maintenance
Corrective maintenance
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
3-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Introduction
4
Overview
Purpose
4-2
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
4-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Introduction
....................................................................................................................................................................................................................................
The RRH 2X60W is a solution for a remote RF transceiver that can be located far away
(500 m to 20 km) from a main Node B and interface with this main Node B through an
optical fiber.
The RRH 2X60W provides an external optical interface to be connected to the optical
module of the main Node B.
It also provides an external radio interface according to UMTS standards.
The following figure shows the connections between RRHs and a d2U Node B in star
configuration.
For details concerning the configurations of implementation, refer to chapter 3 in the
document: Alcatel-Lucent Remote Radio Head 2X60W - 850, 1900 MHz - Technical
Description, 3MN-01477-0003-DEZZA.
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
4-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Hardware description
5
Overview
Purpose
5-2
5-7
5-11
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
5-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Hardware description
....................................................................................................................................................................................................................................
The following figure shows the top view of the RRH 2X60-1900 bulkhead:
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
5-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
The following figure shows the top view of the RRH 2X60-1900A bulkhead:
Figure 5-2 RRH 2X60-1900A four antennas bulkhead top view
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
5-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Hardware description
PRELIMINARY
Hardware description
....................................................................................................................................................................................................................................
The following figure shows the bottom view of the RRH 2X60-1900/1900A bulkhead:
Figure 5-3 RRH 2X60-1900/1900A bulkhead bottom view
Connector description
PRELIMINARY
This topic gives an overview of the connectors located on the RRH bulkhead.
Interface
Connector
Power
48 V DC
GND
Ground connection
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
5-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
Interface
Connector
TX1/RX1
TX2/RX2
PRELIMINARY
Hardware description
CPRI _PRI
CPRI_SEC
MAINT
Notes:
1.
The table below summarizes these states in priority order, from highest (1) to lowest (13).
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
5-5
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
There is only one green-red-yellow tri-colored LED. The Base Band Unit (BBU) gets the
LED status periodically and reports it to the management system.
PRELIMINARY
PRELIMINARY
Hardware description
....................................................................................................................................................................................................................................
Note that one states in the table is marked as not applicable (n/a) for the single LED
display (Background download). In these cases no LED setting is assigned and so the
LED setting defaults to the next lower priority active setting.
ID
RTU State
Description
LED
Display
No power Supplied.
Off
RTU is initializing.
Solid Red
Flash Red
Software download.
Flash Yellow
Nonrecoverable Critical
Failure.
Solid Red
Recoverable Critical
Failure.
Flash Red
Solid Yellow
Non-Critical
Nonrecoverable
Failure.
Solid Red
Non-Critical
Recoverable Failure.
Flash Red
10
External Antenna
Failure.
Flash Red
11
Background Software
Download.
n/a
12
Normal Operation.
Solid Green
13
Standby.
Flash Green
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
5-6
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
The following figures show the top view of the RRH 2X60-850 bulkhead:
Figure 5-4 RRH 2X60-850 two antennas bulkhead top view
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
5-7
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Hardware description
PRELIMINARY
Hardware description
....................................................................................................................................................................................................................................
The following figure shows the bottom view of the RRH 2X60-850 bulkhead:
Figure 5-5 RRH 2X60-850 bulkhead bottom view
Connector description
PRELIMINARY
This topic gives an overview of the connectors located on the RRH bulkhead.
Interface
Connector
Power
48 V DC
GND
Ground connection
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
5-8
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
Interface
Connector
TX/RX
ALM1-3, ALM4-6
PRELIMINARY
Hardware description
CPRI_SEC
AUX Rx
MAINT
Notes:
1.
The two AUX SMA ports are used for antenna sharing feature. They can be configured as
RX ports to bypass the Low Noise Amplifier (LNA) and filters inside the RRH. They also
can be configured as TX ports to output received signal of the main RX ports with 25 dB
gain.
2.
There is only one green-red-yellow tri-colored LED. The Base Band Unit (BBU) gets the
LED status periodically and reports it to the management system.
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
5-9
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
The table below summarizes these states in priority order, from highest (1) to lowest (13).
PRELIMINARY
PRELIMINARY
Hardware description
....................................................................................................................................................................................................................................
Note that one states in the table is marked as not applicable (n/a) for the single LED
display (Background download). In these cases no LED setting is assigned and so the
LED setting defaults to the next lower priority active setting.
ID
RTU State
Description
LED
Display
No power Supplied.
Off
RTU is initializing.
Solid Red
Flash Red
Software download.
Flash Yellow
Nonrecoverable Critical
Failure.
Solid Red
Recoverable Critical
Failure.
Flash Red
Solid Yellow
Non-Critical
Nonrecoverable
Failure.
Solid Red
Non-Critical
Recoverable Failure.
Flash Red
10
External Antenna
Failure.
Flash Red
11
Background Software
Download.
n/a
12
Normal Operation.
Solid Green
13
Standby.
Flash Green
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
5-10
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
PRELIMINARY
Hardware description
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
5-11
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Hardware description
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
5-12
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Overview
Purpose
This chapter describes how to power up and power down the RRH 2X60W.
Contents
Powering up an RRH 2X60W
6-2
6-4
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
6-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
....................................................................................................................................................................................................................................
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage.
For this reason, only trained and qualified personnel (electrical workers as defined in
IEC 60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA
No.10) may install or service the installation.
Procedure
Check that the circuit breaker dedicated to the RRH 2X60W is 15A.
...................................................................................................................................................................................................
Connect the power cable to the DC connector on the RRH 2X60W bulkhead, see Chapter
5, Hardware description
...................................................................................................................................................................................................
Connect the power cable to the power source ( 48 V DC) on the customer site.
...................................................................................................................................................................................................
Check that the status LEDs on the bulkhead display normal operation, see Chapter 5,
Hardware description. If a non-compliance LEDs status occurred then contact the site
coordinator before going on.
PRELIMINARY
...................................................................................................................................................................................................
On the xCCM optical port, check that the Tx and Rx LEDs are green.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
6-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
Check with the WMS administrator if there is not unexpected alarms and that the RRH
2X60W is operational.
E...................................................................................................................................................................................................
N D O F S T E P S
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
6-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
....................................................................................................................................................................................................................................
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage.
For this reason, only trained and qualified personnel (electrical workers as defined in
IEC 60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA
No.10) may install or service the installation.
Procedure
Switch OFF the circuit breaker on the customer power supply plant.
...................................................................................................................................................................................................
Check that the RRH 2X60W is powered off. All LEDs are OFF.
...................................................................................................................................................................................................
Disconnect the power cable dedicated to the RRH from the power source (-48 V DC) on
the customer site.
...................................................................................................................................................................................................
Unscrew the power cable from the RRH DC connector on the RRH 2X60W bulkhead, see
Chapter 5, Hardware description.
PRELIMINARY
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
6-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
7reventive maintenance
P
procedures
Overview
Purpose
This chapter contains the preventive maintenance procedures applicable to the RRH
2X60W.
Contents
Inspecting connectors
7-2
7-4
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
7-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Inspecting connectors
....................................................................................................................................................................................................................................
Inspecting connectors
Before you begin
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage.
For this reason, only trained and qualified personnel (electrical workers as defined in
IEC 60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA
No.10) may install or service the installation.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the WMS administrator of a
service outage before commencing.
Important! The personnel working on the cabinet must be authorized to work
according to the security standards.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
Carry out the following procedure to inspect the connector seals on an RRH 2X60W
bulkhead.
PRELIMINARY
...................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
7-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
Inspecting connectors
....................................................................................................................................................................................................................................
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
7-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
....................................................................................................................................................................................................................................
The RRH can be installed in an outdoor environment using one of the following mounting
kits:
Floor
Wall
Pole (50-152 mm)
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage.
For this reason, only trained and qualified personnel (electrical workers as defined in
IEC 60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA
No.10) may install or service the installation.
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the WMS administrator of a
service outage before commencing.
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
7-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
PRELIMINARY
Procedure
Carry out the following procedure to check the pole brackets and pole bands of the RRH
2X60W.
...................................................................................................................................................................................................
Check that the pole brackets are well tightened to the wall bracket. If not, go to Step 2
.
Check that the pole bands are well tightened around the pole. If not, go to Step 2.
...................................................................................................................................................................................................
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
7-5
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
PRELIMINARY
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
7-6
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
8 orrective maintenance
C
procedure
Overview
Purpose
This chapter describes the corrective maintenance procedure applicable to the RRH
2X60W.
Contents
Replacing an RRH 2X60W
8-2
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
8-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
....................................................................................................................................................................................................................................
An investigation was performed and it was determined that the unit to replace was
faulty.
The existing unit is locked at the WMS.
To replace the RRH 2X60W main body with another RRH 2X60W, you ordered one
of the following spare parts:
RRH 2X60-850, two antennae pre-integrated cabinet 3JR10601AA
RRH 2X60-1900, two antennae pre-integrated cabinet 3JR10801AA
RRH 2X60-1900A, four antennae pre-integrated cabinet 3JR39501AA
Note: For details, see Table 3-1, RRH 2X60W orderable items (p. 3-2)
Note: The RRH 2X60W remains supplied with the mains power supply.
Note: The RRH 2X60W has an integrated handle that does not detach from the unit
once it is installed.
Intervention time:
30 minutes
PRELIMINARY
Required tools
Tool
Quantity
Description,
Hexagonal Keys
6 mm
While the technician is on site, the local configuration data and TTLNA data fields are
set with the local management terminal. The technician needs to commission the RRH
with RMT. The initialization, reset, boot, software download, occur with the WMS. The
configuration of the RRH 2X60W with the proper parameter settings are also established
through the WMS. Many of the settings, commissioning data, local configuration data,
and parameters might not have to be changed at all with the replacement of a faulty unit
with a new hardware unit.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
8-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
WARNING
Electric-shock hazard
Some parts of all electrical installations are energized. Failure to follow safe work
practices and the safety warnings may lead to bodily injury and property damage.
For this reason, only trained and qualified personnel (electrical workers as defined in
IEC 60215 or EN 60215 + A1 or in the National Electrical Code or in ANSI/NFPA
No.10) may install or service the installation.
PRELIMINARY
NOTICE
Service-disruption hazard
This procedure will result in service disruption. Notify the WMS administrator of a
service outage before commencing.
Important! The personnel working on the cabinet must be authorized to work
according to the security standards.
NOTICE
ESD hazard
Electronic components can be destroyed by electrostatic discharge (ESD). Hold circuit
packs only at the edges or on the insertion and removal facilities. Always observe the
general ESD instructions.
Procedure
Preliminary operations:
Shut down the RRH 2X60W, see the procedure Powering down an RRH 2X60W
(p. 6-4).
Remove the solar shield, using the T25 TORX security drive, and store it in a safe
location.
Disconnect all external cables from the bulkhead.
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
8-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
Remove the two RF lightning protectors from the 7/16 female RF connectors (on top
of the main body) and store them in a safe location.
PRELIMINARY
....................................................................................................................................................................................................................................
...................................................................................................................................................................................................
...................................................................................................................................................................................................
Before sending the defective RRH 2X60W to the Repair Center, store the solar shield and
the RF lightning protectors, since these items will be reused for installation of the new
RRH 2X60W.
Note: Only the main body of the defective RRH 2X60W is to be sent to the Repair
Center.
...................................................................................................................................................................................................
Keep the existing cables and protect the connectors with caps near to the existing RRH to
be re-used if necessary.
...................................................................................................................................................................................................
Insert the two RF lightning protectors on the 7/16 female RF connectors (on top of the
main body).
...................................................................................................................................................................................................
Switch on the RRH 2X60, see the procedure Powering up an RRH 2X60W (p. 6-2).
...................................................................................................................................................................................................
Check with the WMS administrator that the RRH 2X60W is operational.
PRELIMINARY
E...................................................................................................................................................................................................
N D O F S T E P S
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
8-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
PRELIMINARY
Appendix A: Product
conformance statements
Overview
Purpose
A-2
A-4
A-5
A-7
Operating conditions
A-8
Cable specifications
A-9
Product labeling
A-10
PRELIMINARY
...................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
A-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
....................................................................................................................................................................................................................................
The RRH falls under the requirements of the Radio and Telecom Terminal Equipment
(R&TTE) European directive 1999/5/EC.
The R&TTE directive covers requirements in the following areas:
PRELIMINARY
Protection of the Health and Safety of users and all other persons, including objectives
with respect to safety requirements contained in the Low Voltage Directive
(73/23/EEC)
Electromagnetic compatibility (EMC) protection requirements contained in Directive
89/336/EEC.
This equipment generates, uses, and can radiate radio frequency energy. If not
installed and used in accordance with the instruction manual, it can interfere with
radio communications. However, there is no guarantee that interferences do not occur
in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on.
The user is encouraged to correct any interference problems. EMC requirements have
been selected to ensure an adequate level of compatibility for apparatus in residential,
commercial, and light industrial environments. Compatibility levels, however, do not
cover extreme cases that can occur in any location, but that have a low probability of
occurrence. In particular, they may not cover cases where a source of interference that
is producing repeated transient or continuous phenomena is permanently present. This
could include, for example, a radar or broadcast site in the near vicinity. In these
cases, it may be necessary to limit the source of interference, and/or apply special
protection to the interfered part.
Note: For operation or maintenance inside Alcatel-Lucent systems, the operator must
always wear the antistatic wrist strap to maintain the integrity of the product.
Effective use of the Radio spectrum allocated to terrestrial/space radio communication
and orbital resources to avoid interference. The routes and standards used to
demonstrate compliance with these requirements are outlined in the following
paragraphs:
Node B EMC
Compliance with essential EMC requirements was demonstrated using E301489-1
& -23.
Node B radio compliance
Compliance with the requirements of effective use of the radio spectrum was
demonstrated using E301908-1 & -3.
Node B safety
Compliance with essential safety requirements was demonstrated using EN60950.
Node B health protection
Compliance with essential health requirements was demonstrated using E50385.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
A-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
A-3
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
PRELIMINARY
....................................................................................................................................................................................................................................
The statements that follow are the product conformance statements that apply to the
Alcatel-Lucent Remote Radio Head 2X60W when deployed in the Americas Region.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
A-4
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
PRELIMINARY
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
FCC Part 68
FIC
04DU9-1SN.
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
A-5
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
This equipment complies with Part 68 of the FCC rules and the requirements adopted by
the ACTA. At the upper-right-hand corner inside the cabinet assembly of this equipment
is a label that contains, among other information, a product identifier in the format of
AAAEQ##TXXXX. If requested, this number must be provided to the telephone
company.
PRELIMINARY
....................................................................................................................................................................................................................................
SOC
6.0N
PRELIMINARY
This equipment complies with Part 24 - Personal Communications Services, Subpart E Broadband PCS.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
A-6
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
....................................................................................................................................................................................................................................
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
A-7
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Operating conditions
....................................................................................................................................................................................................................................
Operating conditions
Operating conditions
The product compliance standards mentioned above are based on the following operating
conditions:
PRELIMINARY
Any changes or modifications made to the product without written approval from
Alcatel-Lucent releases Alcatel-Lucent from responsibility regarding standards
compliance.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
A-8
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
Cable specifications
....................................................................................................................................................................................................................................
Cable specifications
Cable specifications
PRELIMINARY
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
A-9
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
PRELIMINARY
Product labeling
....................................................................................................................................................................................................................................
Product labeling
Product labeling
The product label can be located on the inside or the outside of the product, provided that
the operation and/or maintenance personnel have the information when working on the
product.
Node B labelling for European countries
To indicate compliance with the European R&TTE Directive, the RRH bears the
following label in a visible location:
Manufacturers name
Equipment designation
PRELIMINARY
Labelling for other regions and countries is performed as appropriate and required by the
local regulatory framework.
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
A-10
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014
procedure, 7-2
.............................................................
I
inspecting
pole bands, 7-4
pole brackets, 7-4
.............................................................
PRELIMINARY
Index
procedure
connectors, 7-2
.............................................................
R replacement procedure, 3-2
replacing procedure
RRH 2X60W, 8-2
requirement, 5-11
.............................................................
S Safety statements, 1-1, 1-2
M maintenance
preventive, 2-2
.............................................................
O orderable items, 3-2
.............................................................
P pole bands
inspecting, 7-4
pole brackets
inspecting, 7-4
powering down
RRH 2X60W, 6-4
....................................................................................................................................................................................................................................
Alcatel-Lucent RRH 2X60W
Alcatel-Lucent Proprietary
IN-1
3MN-01477-0004-REZZA
Use pursuant to applicable agreements
Issue 0.02 January 2014
PRELIMINARY
powering up
PRELIMINARY
PRELIMINARY
Index
....................................................................................................................................................................................................................................
....................................................................................................................................................................................................................................
Alcatel-Lucent Proprietary
Alcatel-Lucent RRH 2X60W
IN-2
Use pursuant to applicable agreements
3MN-01477-0004-REZZA
Issue 0.02 January 2014