Académique Documents
Professionnel Documents
Culture Documents
Marder
Monster models
Baja Buggy
The handling with fuels requires circumspective and careful hand- Comments regarding the construction manual:
ling. Imperatively observe the security advices. Before starting the assembly please see through this construction
manual. This way you will get an overview of the whole execution.
-Refuel only if the engine is switched off!
-Take off the body. Please check by means of the parts or bag list if the construction kit is
-Thoroughly clean the area around the fuels nipple. complete and also check the weight of the individual bags for the posi-
-Remove the fuel filler cap and carefully fill in the fuel mixture. tions. Only this way you may be sure that all parts which you need for
-Smoking or any kind of open fire is not admitted. the assembly are available. If a part is missing, please immediately
-Fuels might contain solvent-like substances. Avoid contact with skin contact your specialized dealer.
and eyes. Wear gloves for refueling. Do not inhale fuel vapors.
-Do not spill any fuel. If you have spilled fuel immediately clean the Contents
engine and the model.
-Make sure that no fuel will get into the soils (environmental protecti- Position 1-2: Front and rear differential gear
on). Use an appropriate mat. Position 3-7: Belt drive, belt stretcher, chassis structure
-Do not refuel in enclosed rooms. Fuel vapors accumulate at the soil Position 8-15: Rear axle
(risk of explosion). Position 14-15: Front and rear shock absorber
-Transport and store fuels only in admitted and labeled canisters. Keep
fuel out of the range of children. Position 16-26: Front axle, front bumper
-The operator is responsible for any damages caused to third persons Position 30-36a: Engine, clutch, gear, air filter, tank
in the operating range of the model, respectively of the engine, if they Position 37-43: RC-plate, receiver box, servo saver
are injured or in case of property damage. Position 44-46: Roll cage, throttle rods
-The model must only be passed on to persons who are familiar with
this model and its operation, always provide the operating manual. Position 47-50: Body mounts, side plates, roll cage parts
-Persons with implanted heart pacemakers must not work on running Position 52-56: Body trimmings
engines and on live parts of the ignition system when the engine is
being started.
-The engine must neither be started nor operated in enclosed rooms
(without sufficient ventilation).
-When starting the engine, avoid inhaling the exhausts.
-The model must neither be started nor operated without air filter or
without exhaust system.
-Before every start perform a functional check of the safety-relevant
parts.
-The throttle rods must always return automatically to the idle position.
-Any cleaning, maintenance and repair works must only be performed
with the engine being switched off. The engine and silencers are get-
ting very hot. In particular do not touch the silencer.
Ball bearing
12x28x8
Steel gearwheel
48 teeth
Screw
M4x40 Rear plastic gear
disk 42 teeth
Stop nut M4
Diff. bevel
gear axle
Position 1 Rear
Parts are in Steel gearwheel Plastic stop
48 Zähne differential
bag B disk right
Ball bearing Slant to the
12x28x8 inside Lubricate
slightly
Differential
housing Mounting of the rear differential gear
1. Press the ball bearing 12x28x8 on the differential housing.
Ball diff.
driving axle 2. Insert the differential bevel gearwheels in the differential housing as
pictured in position 1. When using the FG mounting tool Item N°.
08505 the inserting of the bevel gearwheels will be eased considerably.
3. Lubricate the diff. driving axles slightly with grease and push them in
Stop nut M4
the diff. housing.
4. Mount the diff. bevel gear axle. If the bevel gear axle resperctively
the driving axles can only be pushed in severely or if it is impossible to
push them in at any position, you have to disassemble the bevel
gearwheels again and insert them once more.
Screw Rear plastic gear
5. Lubricate the gearwheels slightly with multipurpose grease, e.g. Item N°.
M4x40 disk 42 teeth 06501.
Slant to the
inside 6. Now press the parts on the diff. housing as described in position 1
and in the given sequence: Steel gearwheel 48 teeth ( consider moun-
ting direction of the slant), rear plastic gear disk 42 teeth, plastic stop
disk right. Fix the complete unit with the M4x40 countersunk screws
and stop nuts M4 (impress the M4 stop nuts in the plastic stop disk
Inserting of the diff. right and use the screw retention high-strength).
bevel gearwheels or
of the complete
package is much
easier if you use the
FG mounting tool
08505.
Front plastic
Position 2
stop disk Parts are in
right bag C
Front
Differential differential
housing
Stop nut M4
Right plastic
Mounting of the front differential gear stop disk
1. For mounting of the front differential gear you have to disassemble
the differential from your 2WD model, remove diff. bushing and steel Bearing
Screw
gearwheel 48 teeth. M4x40 Slant to the shaft 6x50
2. Now mount the parts on the diff. housing as described in position 2 outside
and in the given sequence: Front plastic stop disk left (consider moun- Deflection roller
ting direction of the slant), front plastic toothed belt wheel 42 teeth, pla- Front plastic 16mm
stic stop disk right. Fix the complete unit with the M4x40 countersunk toothed belt
wheel 42 teeth
screws and the stop nuts M4 (impress the M4 stop nuts in the plastic
stop disk right and use the screw retention high-strength).
Toothed belt
3. Push the bearing shafts 6x50mm centrally in the deflection roller wheel 12 teeth
Bearing
16mm and in the 12-teeth toothed belt wheel. shaft 6x50
Front differential
Position 3 mounted 2. Mount front differential gear, deflection roller
Parts are in 16mm, toothed belt wheel 12 teeth in the left
bag C front axle housing as described in position 3.
Front axle
housing left
3. Now put the toothed belt on the front dif-
ferential gear, also deflection roller 16mm,
toothed belt wheel with 12 teeth as descri-
bed in position 3.
Position 4
Parts are in
bag C
Front axle
1. Impress ball bearings 6x16x6 in both front housing left
axle housings left and right.
Alloy chassis
Front axle
housing right
Position 5
Parts are in
bag B+C
1. Place the lower part of the belt channel (with the closed side facing
upwards) on the bottom part of the toothed belt. Then push the top part
of the belt channel in the bottom part. Now insert the complete belt
channel in the opening of the front axle housing (see position 5a). Make
sure that the toothed belt is running smoothly.
Rear axle mount 2. Fix the belt channel from underneath to the alloy chassis using the
right
4,2x16 countersunk screws.
Countersunk
screw M4,2x16
Front axle hou-
sing left
Position 5a
Parts are in
bag B+C
Fix the belt channel from underneath to the alloy
chassis with the 4,2x16 countersunk screws.
Alloy chassis
Front axle
Upper part housing
belt channel right
Toothed belt
Screw
M4x14
1. Impress the plastic bearing seat
Disk Ø4,3 with inbound collar (pay attention to
fitting position) in the left and right
Countersunk Screw Fitting position for
4,2x16 toothed belt wheel stretching pulley housing as descri-
screw M4,2x16 40 teeth bed in position 6.
Tipp: The position of the front bearing seat is made for Fitting position for
the front plastic toothed belt wheel with 42 teeth. The toothed belt
wheel 42 teeth
position of the rear bearing seat is made for the front
Stretching pulley
plastic toothed belt wheel with 40 teeth. housing left
2. Push the bearing shaft for the stretching pulley Ball bearing
housing centrically in the 3 ball bearings 10x19x7. 10x19x7
Plastic
All metric screws need to be secured with thread lock fluid. bearing seat
Stretching pul-
ley housing
Position 7 right
Parts are in bag B
1. Place the mounted stretching pulley housing ob toot-
hed belt and belt channel as described in position 7
and fix it on the alloy chassis using the 4,2x16 counter-
sunk screws. For this purpose, slightly move the belt.
2. When the assembly is performed, turn the belt in run-
ning direction. Make sure the belt is easily rotatable.
Stretching pulley
housing mounted
Countersunk
screw 4,2x16
Alloy chassis
1. Push the rear axle cover between the left
Position 8 and right rear axle mounts and fix it with the
Parts are in Stabilizer
bag D alloy connection brace, M4x20 pan-head
5mm
screw and disk Ø4,3.
Screw 2. Disassemble the rear lower wishbone with
4. Impress the stabilizer 5mm (only for Monster/Stadium M4x20
models) in the plastic braces for stabilizer. stabilizer from your 2WD model (stabilizer
Disk
Ø4,3 only in Monster/Stadium models).
Rear axle mount
right 3. Fix the rear lower wishbones to the front
Alloy connec- ball-and-socket joints using M5x30 counter-
tion brace sunk screws and 4 disks Ø5,3 (between ball-
Rear axle cover
and-socket joints and alloy chassis), then fix
all with M5 stop nuts to the alloy chassis.
Now fasten the rear ball-and-socket joints
with M5x25 countersunk screws and M5
stop nuts to the alloy chassis. Make sure the
mounted wishbones can be moved easily up
and down.
Ball-and-
Stop nut M5 socket joint
Adjusting screw
r/l 32mm
Position 9
Parts are in
bag D
m
8m
.3
ox
pr
ap
m
7,5m
ox. 3
appr
Screw
4,2x22
Screw
4,2x9,5
Disk Ø4,3
Rear lower
wishbone
Rear axle
mount left
Rear lower
wishbone pin
Rear driving
shaft Retaining
washer Ø5
Rear upright
left
Position 11
Parts are in bag D
Retaining
washer Ø5
Adjusting clips Rear upper
wishbone pin
Headless pin
M5x25
Rear upper
wishbone
Rear wishbone
thread rod
M10/M8 84mm
Ball-and-socket joint
Left upright
Disk Ø5,3
4. Push two adjusting clips each in the rear upper Screw
M5x35
wishbone pins in the front between rear axle mounts Steel ball
and rear upper wishbones, then push one adjusting 10x13
clip each in the rear upper wishbone pins in the rear Make sure the rear wishbones
Position 13 between rear damper plate and rear upper wishbones. can be moved easily up and
BaustufeParts
14 are in down.
Teile sind bag
in D
Beutel
m
7m
Screw .7
M5x35 prox
ap
Disk
Ø5,3
Damper piston
Hint: Slightly lubricate the o-rings with Retaining
silicone oil when mounting. If you use washer Ø3,2
the FG mounting tool 06853 + 06854,
the mounting of the shock absorbers Lower shock
will be eased considerably. absorber locking B O-ring
4x2
Lower shock
absorber locking A
Damper piston
rod long
Damper fixing
short
Screw
M5x25
Rear damper
plate
Rear shock absor-
ber mounted
3. Insert the front lower wishbones in the front axle housings, then
push the front lower wishbone pins with threaded hole towards
Screw the front in the front axle housings and press them through the
4,2x16
pre-assembled front lower wishbones. Make sure the wishbones
can be moved easily up and down.
Front axle
housing left
1. Screw the headless pin M5x16 from the
Headless bottom into the front lower wishbone until
Front lower pin
Guide for wishbone pin M5x16 approx. 2mm thread are visible.
stabilizer
4. Impress the stabilizer guide as
locking device for the front lower
wishbone pins into the left and right
front axle housings and fix it using
4,2x16 pan-head screws.
Front lower 2. Disassemble the steel balls from the front axle of your exi-
wishbone sting 2WD model and push them into the front lower wishbo-
nes, then screw in the 2,9x13 pan-head screws.
Screw Steel ball
2,9x13
Fixing nut for
front upright Front upright
Position 17
Position 18 Parts are in
Parts are in Front upright 4WD right
4WD left bag F
bag F
Ball bearing
17x26x7
Ball bearing
8x22x7
1. Impress mounting nuts for front uprights from the Fixing nut for
front upright
inside into the left and right uprights.
2. Push the ball bearing 17x26x7 from the inside into
the left and right upright.
3. Disassemble the ball bearing 8x22x7 from the
upright of your existing 2WD model and push it into the
front upright 4WD.
Disk
Ø8,4
Retaining
Adjusting washer Ø5 Diff. dri- 1. Screw the front wishbone thread rods M10/M8
clips ving axle 66mm into the front upper wishbones, then turn
Front upper the ball-and-socket joints on the front wishbone
wishbone Front axle Front lower
pin housing wishbone
thread rods M10/M8 66mm.
2. Dismount the steel balls from your existing
2WD model and press them into the ball-and-
Headless socket joints.
pin Screw 3. Press the front upper wishbone pins through
Front upper M5x25 M5x30
wishbone the pre-assembled front upper wishbones into the
front axle housings as described in position 19.
Disk
Ø5,3 Fix the front upper wishbone pins with Ø5 retai-
Front dri-
ving shaft ning washers.
Disk 4. Withdraw the diff. driving axles from the front
Ø5,3 differential and press them with disk Ø8,4 in the
Front wishbone front differential again.
thread rod 5. Push the front driving axles into the pre-assem-
M10/M8 66mm Front upright bled left and right uprights. Dismount square
Front 4WD left
driving wheel driver from your existing 2WD model and
axle
mount it on the faces of the front driving axles
Headless pin
M6x6 with the crank facing the bearing.
Ball-and-socket joint Steel
ball
Screw Square wheel
M5x30 driver 14mm
Disk
Disk Ø5,3
Ø5,3
approx. 7,5mm
ap
pr
ox
..4
9,
5m
m
Screw
ap M5x30
pr
ox
Impress four adjusting clips each in the .19 Disk Mount the left and right
,5m Ø5,3
front between front axle housing and front m uprights to the lower wishbo-
upper wishbones into the front upper nes and to the ball-and-socket
wishbone pins. joints of the upper withbones
using Ø5,3 disks between
steel ball, screw and uprights.
At the same time mount the
driving shaft between front
driving axle and diff. driving
Make sure the driving shaft has not more than 2mm Front upright
clearance in horizontal position. Corresponding to the left axle.
adjustment of the upper wishbone (camber) you have
to mount or dismount enclosed steel disk Ø8,4 bet-
ween diff. axle and ball bearing.
Baja Buggy Position 20+21 Stop nut M4
1. Fix the front shock mount 4WD to Position 20 Screw
Parts are in M4x16 Disk
the reinforcing plate for the front axle bag G Ø4,3
by using M4x16 countersunk screws,
Ø4,3 disks and M4 stop nuts. Baja Buggy Screw
4,2x13 Reinforcing plate
Disassemble countersunk screw for front axle
M4x25 and M4 nut from the shock
mount of your existing 2WD model and
mount them at the front shock mount
4WD.
2. Mount the plastic fixing plate with
brake guide rail and alloy distances
between brake guide rail and reinfor- Plastic fixing
Screw plate
cing plate to the reinforcing plate for M4x25
the front axle using M4x30 cylinder
screws, disks Ø4,3 and M4 stop nuts. Nut Brake
M4 guide
rail
Front shock
mount 4WD
Alloy
distance
Position 21 Disk
Ø4,3
Parts are in
bag G
Screw
Disk M4x30
Baja Buggy
Ø4,3
Stop nut M4
Reinforcing brace
for front axle
Screw
M4x25
Marder/Baja Buggy Position 23 Disk
Ø4,3
Parts are in
bag G Screw
Stop nut 4,2x13
M4
Stop
nut M4
Screw
4,2x16
Nut M5
Screw
4,2x16
Screw
4,2x32
Body support
Screw
4,2x13
Body clip
Screw
4,2x16
Dampening rubber Screw
for body support 4,2x13
Monster/Stadium Position 25
Parts are in
Monster/Stadium Position 24-25 bag G
1. Mount front shock mount 4WD to the reinforcing plate for front axle
using 4,2x16 countersunk screws.
2. Dismount the plastic parts for reinforcing brace from the shock mount of
your existing 2WD model and fix them to the front shock mount 4WD by
using 4,2x32 countersunk screws (position 25).
3. Screw the headless pins M5x45 from the front into the front shock
mount 4WD until they are flush with the rear side of the shock mount.
Then counter the headless pins witrh M5 nuts.
4. Disassemble the adjustable body mounts from the shock mount of
your existing 2WD model and mount them to the front shock mount
4WD by using 4,2x16 pan-head screws.
5. Fix the body clips in the adjustable body mounts as described in position Nut M5
25 and press on the body support. Use the body clips and the body sup- Plastic
port from your existing 2WD model. Headless mount
pin M5x45
Screw
4,2x32
Position 26
Parts are in
bag G
Monster/Stadium
Stop
nut M5
Monster/Stadium Position 26
1. Fix the assembled reinforcing plate for front axle
on the front axle carrier using 4,2x13 pan-head
screws.
2. Mount the front shock absorbers to the front lower
wishbones with M4x14 cylinder screws, then fix the
Screw
4,2x16 shock absorbers at the top with M5 stop nuts.
3. Assemble the front bumper at the alloy chassis
using M4x8 pan-head screws and disks Ø4,3, then fix
it with 4,2x16 pan-head screws at the front axle car-
riers.
Front bumper
Disk
Screw Ø4,3
M4x8
Screw M4x14
Position 30 1. Cover the outlet port of the engine
Parts are in with an adhesive tape.
bag H
2. Saw off the housing part
with an metal hand saw, see Position 31a
also illustration in position 31. Parts are in
bag H
on
cti
ire
gd
Clutch spring
ivin
Dr
Clutch blocks
Position 30b
Parts are in
bag H
Position 30d
Parts are in
bag H
Plastic engine
mount large
4WD
Ball bearing
10x19x7
Disk
6x15x1
Steel fixing plate long
Shaft washer
Steel fixing plate short Screw
4,2x13 Dowel screw for
Screw clutch blocks
4,2x13
Make sure that driving gearwheels, driving shafts
Position 32
Parts are in a.s.o. can be turned easily without any resistance. Foam filter
Screw
bag I Screw 4,2x16
Basic 4,2x13
Airfilter
adapter body
Filter cover
O-ring for airfilter
adapter
Insert the o-ring for the airfilter
Screw
4,2x13 adapter in the basic body and
Plastic engine fasten it to the airfilter adapter
mount large
4WD Gearwheel using 4,2x13 countersunk screws.
cover gear
Press the oiled foam filter of your
Screw existing 2WD model on the basic
M6x16
ge
flan body and fix it with filter cover and
lutchl
C 4,2x16 countersunk screw.
Screw
Gear Headless 4,2x13
shaft pin
4WD Steel M5x5
gearwheel Mount the gearwheel cover at the large plastic
14 teeth
engine mount 4WD using 4,2x13 pan-head
Gear screws as described in position 32+34.
plate
1. Remove the adhesive
tape from the outlet port of
the engine and re-assemble 3. Push the gear shaft 4WD through the ball bearing of the large
muffler with muffler gasket plastic engine mount 4WD and re-assemble the gear plate at the
from your existing 2WD clutch flange using M6x40 cylinder screws and Ø6,4 disks.
model. Disk 4. Press steel gearwheel 14 teeth on the gear shaft 4WD as pic-
Ø6,4
tured and fix it on the surfaces of the gear shaft 4WD using
M5x5 headless pins, secure with M6x16 countersunk screw and
use a high-strength screw retention (Position 32+34).
Screw
M6x40
Hint: Rinse the existing foam filter (if it is dirty) with rinsing water,
2. Remove retaining washer Ø7 of the gear shaft from the plastic let it dry and oil it again. To oil the foam filter knead it in a plastic
gearwheel. Dismount headless pin M5x5 of the brake square and pull bag with FG filter oil Item N°. 06441 repeatedly.
out the 2WD geart shaft from the gear plate. Then press the 4WD
gear shaft through the brake square, gear plate, shim ring 1x16x1
and plastic gearwheel and secure it with retaining washer Ø7. Mount
brake square backlash-free on the surface of the gear shaft 4WD
using the headless pin M5x5.
Gear Shim ring
Position 33 10x16x1
Parts are in plate
Plastic Position 34
bag I gearwheel Parts are in
bag I
Gear Brake
shaft square
4WD
Headless
pin
M5x5
Clutch bell
Retaining
washer Ø7
Headless
pin
M5x5
Retaining
washer Ø7
Tank complete
Tank mount
Engine fixing
disk
Screw
4,2x16
Alloy chassis 1. Insert the complete engine in the
Screw alloy chassis and fasten it with
4,2x16 4,2x32 pan-head screw and disk
Ø4,3 through the rear axle mount.
Do not tighten the 4,2x32 pan-head
screw yet, see also position 36a.
Screw 2. Fix the pre-assembled engine
4,2x16
using 4,2x16 countersunk screws
All metric screws need to be secured Tank base
and engine fixing disks from
with thread lock fluid. underneath on the alloy chassis.
Position 36
Parts are in
bag I
Position 36a
Parts are in
bag I
Alloy connec-
ting brace
Screw
4,2x32
Plastic engi- Disk Ø4,3
ne mount
large 4WD Rear axle
mount left
Position 37 Flexible aerial Hint: Fill the bottom part of the receiver box 1. Dismount the rc-plate from your existing 2WD
Parts are in with some foam to protect the receiver model, remove battery mount, servos and receiver
bag J against vibrations. box.
Receiver 2. Mount the throttle/brake servo and the stee-
box ring servo in the plastic rc-plate 4WD as descri-
bed in position 37.
3. Fix the receiver box to the plastic rc-plate
Battery mount with 4WD using 2,9x13 pan-head screws, connect
Steering servo receiver battery
the servo cables, battery cables to the receiver
again and check the function. Now stow the
receiver and the rest of the servo cables in the
receiver box, lead the aerial cable of the receiver
in the flexible aerial.
Screw 4. Press the collar disk for the 4WD rc-plate into
2,9x13 Body clip the plastic rc-plate 4WD.
5. Mount the bolts for the battery mounts to the
plastic rc-plate 4WD using 2,9x13 pan-head
screws. Fix the battery mount with receiver bat-
tery with body clips to the bolts.
6. Now press the servo arm back on the steering
Bolt for bat- servo as described in position 38 and fix it with
Collar disk for tery mount
enclosed screw. The servo arm should be in a
rc-plate 4WD Screw
2,9x13 90-degree position to the steering servo at neu-
Plastic rc-plate Gas/brake tral position of the radio control, change the
4WD servo position of the servo arm correspondingly.
Screw
2,9x13
Position 38
Parts are in
bag J
Plastic rc-plate
4WD Collar disk for
must face the servo saver) rc-plate 4WD
to the servo saver by
using M4x20 cylinder 1. Impress the tension sleeve for servo saver Position 39
screws and M4 stop nuts. Parts are in
from above through servo saver part B and bag J
servo saver part A.
2. Mount the servo saver spring with the Servo saver
M10 nut on the thread of the tension slee- axle
ve and check on free movement.
3. Lubricate the servo saver axle slightly
Servo rods and press it from the top into the tension
Joint mounted
ball sleeve for servo saver. Secure the servo Tension sleeve for
saver axle with an M5x10 pan-head servo saver
Screw
M4x20 screw. Use screw retention lacquer.
Servo saver
mounted Servo
saver
Part A
Stop nut Servo
M4 Steel ball saver
7mm Part B
Ball bearing Rods M4x51
Track rod 7mm
mounted
Servo
6. Dismount the servo rods from your existing 2WD model saver
Screw spring
2,9x19 and remove the ball-and-socket joints from the linkage.
7. Screw the ball-and-socket joints 7mm on the rods M4x51
and press the steel balls 7mm into the ball-and-socket joints. Nut M10 for
8. Fix the servo rods (collar of the steel ball must face the servo saver
servo saver) at the inner hole of the servo saver using 2,9x19
Screw
pan-head screws as pictured. M5x10
Position 41 Steering servo
Parts are in Screw
bag J M5x16
Disk
Front axle Ø5,3
stiffening
Servo
saver
Plastic rc-plate 4WD
Servo rods
Track rod
Alloy chassis
Screw
4,2x16
Screw Screw
Front upright 4,2x16 2,9x16
left 1. Mount the plastic rc-plate 4WD underneath the front axle stif-
fening to the alloy chassis using 4,2x16 countersunk screws.
Stop nut Disk 2. Now mount the servo saver underneath the plastic rc-plate
M4 Ø4,3
Screw 4WD by using M5x16 pan-head screw and Ø5,3 disk as pictu-
M4x20 red. Use screw retention lacquer.
Track rod
Position 43
Parts are in
bag J
Disk Screw
Ø4,3 M4x20
Front upright Stop nut
left M4
Position 45
Parts are in
bag K
1. Mount the throttle rods to the carburetor arm using
collets and M3x3 headless pins as described in positi-
on 45. Keep some clearance between the collets and Carburetor
the carburetor arm. Make sure the carburetor arm can arm Headless
be easily moved and does not jam. pin M3x3
Headless
Collet pin M3x3
Collet
s
rod
tle
rot
Th
s
rod
rake
B
Tipp: Do not tighten the M3 stop nut at the throttle Headless pin
pivot post. The throttle pivot post and the throttle rods M3x3
must run smoothly, move easily and should neither
touch nor clamp in any position.
Monster/Stadium models
Position 47 1. Dismount roll bar and reinforcing brace from your existing 2WD
Parts are in model.
bag K
2. Mount the plastic parts for the reinforcing braces at the roll bar
again using 4,2x32 pan-head screws as pictured. Push the reinforcing
Spoilerhalter
braces into the plastic parts for the braces at the front shock mount
Kunststoff and fix them using 2,9x9,5 pan-head screws.
strebe kurz
Screw
2,9x9,5 Reinforcing brace
Scheibe
Plastic part for
Ø4,3
reinforcing brace
Schraube
Schraube 4,2x13
4,2x22 Auspuffrohr
Halterung für
Auspuffrohr
Roll bar
Dämpferplatte
hinten 4WD
Baustufe 50
Alloy chassis
Teile sind in Baja
Screw
Schraube Beutel 4,2x16 3. Mount the roll bar to the alloy chassis
M6x75
using 4,2x16 countersunk screws.
1. Disassemble the left and right alloy side plates from your existing 2WD model and mount them to
the alloy chassis using M4x8 pan-head screws. Fix the left and right alloy side plates to the front
shock mount using 4,2x16 pan-head screws, Ø4,3 disks and plastic bushes 4/6x5.
2. Fasten the left alloy side plate with M6x75 cylinder screw, Ø6,4 disk and alloy distance 10x34.
Position 48 3. Fasten the right alloy side plate with M4x45 cylinder screw, Ø4,3 disk and alloy distance 8x27.
4. Dismount the complete rear spoiler mount from your existing 2WD model and fix it at the rear shock
mount 4WD by using M4x20 cylinder screws and M4 stop nuts. Spoiler mount and rear body mounts
can differ for Hummer, Jeep and Beetle Pro models.
5. Mount the long plastic braces with 4,2x32 pan-head screws and roll bar.
Plastic brace
Screw long
Monster/Stadium models 4,2x32
Plastic
bush
4/6x5mm
Disk
Ø4,3
Screw Allloy distance
4,2x16 10x34
Alloy side
plate left
Screw
4,2x13
Screw Allo
M4x8 y ch
Marder/ ass
Rocker is
panel left
Baja Buggy Screw
M4x8
Rear damper
1. Dismount the left and right rocker panels from your existing plate 4WD
2WD model and fix them to the alloy chassis by using M4x8 pan-
head screws. Screw
M4x20
2. Remove the complete rear spoiler mount from your existing
2WD model and fix it at the rear 4WD shock mount using M4x20
cylinder screws and M4 stop nuts.
3. Mount the long plastic braces with M4x50 headless pins (for
Marder only with 4,2x32 pan-head screws) and plastic parts for
reinforcing brace to the roll bar.
Alloy cover
Screw
2,9x9,5
Position 50
Parts are in Long alloy
bag K brace Baja 4WD
Screw
2,9x9,5
Drill 2,5mm
Baja Buggy Front
Plastic brace for
cover
alloy plate
Front plastic
fixing plate
Position 52
Hummer
Position 53 Cut out the left and right wheel cases of the front body-
Baja Buggy shell a little more as pictured by using a scissors or a
model knife to prevent the bodyshell from rubbing
against the wheels.
Monster Truck
Jeep
Jeep
Position 56
Marder
Marder
Marder
66305 66304
06086
06089
06445
68140/02
06421/05 06088
68140/01
07091
68150/01
06093
06732/03
06093 06088
06092
68155 07087/01
06714/19
06022/01
60215/05 06714/13
06714/09
06714/09
06540
60236
60237
8
28
66
09
4/
671
0
66200
05718/16
3 60235 68240
06734/04 23
60 3
01
06 66285/01
682
06011
58
662
080
66287
93
04 06013
06738/04 34/
20/
25 067 8/04
3
067 067 06731/08
662
53
682 06731/08
662
067
06726/16
067
06739/04
56
52
54
57 682
25/
662
20/
06734/05
662
66286
30
06013 06712/16
40
54
060
66255
64
067
66245
38/
060
5
63/0 01
04
060 26/
30
682
06069/01 71 0
662 25/2
66244
50
76
067 06714/16
6 68
16/1 682 06730/16 06029/07
067 68323
06714/19
662
5
34/0
067
67
06734/04
682
060
1
50/0 68271
662 06029/07 68325
65
28/
68270 06722/30
06731/08
060
01
06734/04 68326
08
66230
60230 06725/20
06081/01 06734/06 06735/10
06714/13 06112 06738/06 06081/01 06738/04
06030
06712/13 06712/16
07384 06451/03 06464/04
66218/01
06464/05
8
30/0 5 06465/01
073
34/0
067 06451/04
06465-Set
FG Modellsport GmbH
Spanningerstr. 2
5 06038 06712/16 73650 Winterbach-Germany
6 738/0 1 Phone: +49 7181 9677-0
0
07332 34/0 06723/16 Fax: +49 7181 9677-20
061 13 66217 info@fg-modellsport.de
6/
07329/01
06728/03 1
08345 067 www.fg-modellsport.de
06020 11 06730/05
06726/40 662
06716/32
07331/06 6
3 24 06734/04
8/0 68 06728/03
06738/03 0672020 06727/10
06036/05
06 07315 06020
06728/03 3 1
6716/1 6037/0 68216 06126
06020 0 0 /08
06738/03 15 06039/07 06724
68 2
06534/02 06739/03 06730/05 06045/03
07315/01
06038
01
07316
37/
6 06042/01
05019/01 39/0
060
061
07317/11 06724/08
06044/01
06732/05
07318 06036/05
06745 08456 06045/01
06724/18
06049/01 06050
06137/01
06734/06 06051
06040/05
06727/40
06730/05 06732/07
06432
06427
06732/07
06725/20 60238
66210 60239/01
06013
067
06716/22
34/
06730/30 06033
31 21 06068
060 682 06738/05 06716/22
06064
06029/08
06066/02
662
06081/01
12
06063/05 06712/16
05 06726/25
38/ 06722/25
067 68205
00 06029/08 03 06739/05
662 00/
061
30
22/ 06 06738/05 08523
067 081
/01
067
32/0
067 5 06072/02 06069/01 66304
34/0
5 100
37
5
07
662
30/2
75
060
067
06729/30
06036/05 06073 06080
16 06350
12/ 68225 06732/05
067
07353 66222 06078/05 60209/05
07351 06077
66223 66226
01
38/ 06077/08
662 07352 06712/16
06734/05
06078/05
68220 06079
06077/05 06733/06
07348 06734/04
06734/06
66238/02 06712/16 06731/14 06029/08 66230
06722/35 06738/06 06112
Spare parts list for 68040R - 68050R Item N°. Description Item N°. Description Item N°. Description
1:6 BAJA BUGGY 4WD 06510/20 Oil for shock absorber 2000, 1pce. 07352 Fuel tube/Zenoah, 1pce. 68265 Front lower plastic wishbone 4WD, 1pce.
06534/02 Throttle pivot post 2,1 mm, set 07353 Rubber gasket f. tank, 1pce. 68266 Front upper plastic wishbone 4WD, 2pcs.
1:6 Marder Off-Road Buggy 4WD 06540 Receiver box, 1pce. 07384 FG Zenoah engine G260RC 68268 Front lower wishbone pin 106mm, 2pcs.
06546 FG receiver battery NiCd 6V/1500mAh, 1pce. 07561 Hitec RCS Aggressor FM/DCX receiver, set 68270 Front plastic upright 4WD, 2pcs.
Item N°. Description 06546/04 Single storage batt. NiCd 1,2V/800mAh, 4pcs. 08093 Brake guide rail, 1pce. 68271 Fixing nut f. front upright, 2pcs.
05014/05 Bolt for battery holder, 2pcs. 06548 Charger 220V/Fut., Hitec, 1pce. 08345 Coupling flange Zenoah 1:6, 1pce. 68276 Front driving axle 4WD, 1pce.
05019/01 Pressure spring 0,4x5x25mm, 2pcs. 06712/13 Counters.sh.met.screws,4.2x13mm,20pcs. 08456 Steel brake plates, 2pcs. 68277 Front driving shaft 4WD, 1pce.
06011 Side guards l./r. each, 1pce. 06712/16 Counters.sh.met.screws,4.2x16mm,20pcs. 08523 Rear shock absorber set, long, 2pcs. 68323 Servo saver A/B, 1pce.
06013 Body clips, 10pcs. 06714/09 Pan-head tap.screws, 2.9x9.5mm, 15pcs. 60209/05 Baja tires S wide glued, 2pcs. 68324 Servo saver axle new, 1pce.
06020 Collets 2,1 mm, 5pcs. 06714/13 Pan-head tap.screws, 2.9x13mm, 15pcs. 60215/05 Baja tires M narrow glued, 2pcs. 68325 Servo saver spring 2,0mm, 4WD, 1pce.
06022/01 Flexible aerial and mount, 1pce. 06714/16 Pan-head tapping screw 2,9x16mm, 15pcs. 60230 Front bumper Baja, 1pce. 68326 Nut M10 f. servo saver, 1pce.
06026/01 Rods M4 x 51mm, 2pcs. 06714/19 Pan-head tapping screw 2,9x19mm, 15pcs. 60233 Roll cage parts front, 2pcs. 68327 Tension sleeve f.servo saver new, 1pce.
06028/01 Track rod right/left 1:6, 74mm, 2pcs. 06716/13 Pan-head tap.screws, 4.2x13mm, 15pcs. 60235 Front alloy plate, 1pce.
06029/07 Ball-and-socket joint for M6, 4pcs. 06716/16 Pan-head tap.screws, 4.2x16mm, 15pcs. 60236 Alloy cover, 1pce.
06029/08 Ball-and-socket joint for M8, 4pcs. 06716/22 Pan-head tap.screws, 4.2x22mm, 15pcs. 60237 Plastic brace for cover, 2pcs.
06030 Steel balls 10 x 10,75, 4pcs. 06716/32 Pan-head tap.screws, 4.2x32mm, 15pcs. 60238 Plug protection, 1pce.
06031 Roll cage, 1pce. 06720/25 Rec. counters.head screws,M4x25mm,10pcs. 60239 Plastic brace long, 2pcs.
06033 Wing mount, 1pce. 06720/40 Rec.counters.head screws,M4x40mm,10pcs. 60239/01 Plastic brace short, 2pcs.
06034/01 Plastic part f. stiffening brace, 2pcs. 06722/25 Rec.counters.head screws,M5x25mm,10pcs. 60240 Rear body mount Baja, 2pcs.
06036/05 FG ball bearing 10x19x7 w. grease fill., 2pcs. 06722/30 Rec.counters.head screws,M5x30mm,10pcs. 66155 Model sticker f. Baja Buggy 4WD comp., set
06037/01 Steel fixing plates, 2pcs. 06722/35 Rec.counters.head screws,M5x35mm,10pcs. 66200 Alloy chassis 4WD, 1pce.
06038 Engine mount washers, 4pcs. 06723/16 Rec.counters.head screws,M6x16mm, 10pcs. 66207 Plastic gear disk rear 42t. 4WD, 1pce.
06039/06 Gear plate 06, 1pce. 06724/08 Socket head cap screws 8.8,M3x8mm,10pcs. 66208 Steel gear wheel 48t. 4WD, 1pce.
06039/07 GRP brake plate, 1pce. 06724/18 Sock. head cap screws 8.8,M3x18mm,10pcs. 66210 Rear axle cover 4WD, 1pce.
06040/05 FG ball bearing 10x22x6 w. grease fill., 2pcs. 06725/14 Socket head cap screws M4x14mm,10pcs. 66211 Gear wheel protection 4WD, 1pce.
06042/01 Brake square 97, new 1pce. 06725/20 Socket head cap screw M4x20mm, 10pcs. 66212 Alloy connection rod gear 4WD, 1pce.
06044/01 Brake disk epoxy 97, new 1pce. 06726/16 Socket head cap screw M5x16mm, 10pcs. 66217 Steel gear wheel 14t. narrow, 1pce.
06045/01 Brake operating shaft 97, new each 1pce. 06726/25 Socket head cap screw M5x25mm, 10pcs. 66218/01 Basic body f. inlet silencer, 1pce.
06045/03 Brake lever 30mm, 1pce. 06726/40 Socket head cap screw M5x40mm, 10pcs. 66222 Bear.shaft f. tension. pulley housing 4WD,1pce.
06049/01 Clutch bell, 1pce. 06727/10 Socket head cap screws M6x10mm,5pcs. 66223 Plastic bearing seat 4WD, 2pcs.
06050 Plastic gear carrier 60 mm, 1pce. 06727/40 Sock. head cap screws 8.8,M6x40mm, 5pcs. 66226 Wishbone thread rod M10/M8x84mm, 2pcs.
06051 Dampening rubber, 4pcs. 06728/03 Headless pin M3x3mm, 15pcs. 66230 Alloy square wheel driver 14mm/M6, 2pcs.
06063/05 FG ball bearing 12x28x8w. grease filling, 2pcs. 06729/30 Headless pin M4x30, 15pcs. 66235 Lower part belt channel, 1pce.
06064 Differential housing, 1pce. 06729/50 Headless pin M4x50, 8pcs. 66236 Upper part belt channel, 1pce.
06066/02 Diff. gearwheel A reinforced, 2pcs. 06730/05 Headless pin M5x5mm, 15pcs. 66237 Toothed belt, 1pce.
06067/02 Diff. gearwheel B reinforced, 2pcs. 06730/16 Headless pin M5x16mm, 15pcs. 66238/01 Lower tank mount 4WD, 1pce.
06068 Bevel differential gear axle, 1pce. 06730/25 Headless pin M5x25mm, 15pcs. 66238/02 Upper tank mount 4WD, 1pce.
06069/01 Diff.driving axle, pluggable, 1pce. 06730/30 Headless pin M5x30mm, 15pcs. 66244 Ball-and-socket joint 7mm f.M4, 8pcs.
06072/02 Adj. rear lower wishbone Monster, 1pce. 06731/08 Tallow-drop screw M4x8mm, 15pcs. 66245 Steel ball 7mm, 4pcs.
06073 Rear lower wishbone pin, 2pcs. 06731/14 Tallow-drop screw M4x14mm, 15pcs. 66250/01 Guide f. front stabi 4mm 4WD, 2pcs.
06075 Rear upper wishbone pin, 2pcs. 06732/03 Retain.washers-spring steel,3.2mm, 15pcs. 66254 Bearing shaft, 6x50mm, 1pce.
06077 Rear upright raised l./r., 2pcs. 06732/05 Retain.washers-spring steel, 5mm, 15pcs. 66255 Ball bearing 6x15x5, 4pcs.
06077/05 Steel ball 10x13 for rear upright, 2pcs. 06732/07 Retain.washers-spring steel, 7mm, 15pcs. 66256 Front plastic toothed belt wheel 42t. 4WD,1pce.
06077/08 Distance bush for rear upright, 2pcs. 06733/06 Headless pin, M6x6mm, 15pcs. 66257 Front plastic stop disk left 4WD, 1pce.
06078/05 FG ball bearings 8x22x7 w. grease filling, 2pcs. 06734/04 Washers, steel 4.3mm, 15pcs. 66258 Plastic stop disk right 4WD, 1pce.
06079 Rear driving axle, 1pce. 06734/05 Washers, steel 5.3mm, 15pcs. 66267 Wishbone thread rod M10/M8x66mm, 2pcs.
06080 Rear dogbone, 1pce. 06734/06 Washers, steel 6.4mm, 15pcs. 66271 Ball bearing 17x26x7, 2pcs.
06081/01 Ball 5/10x15 M5, 4pcs. 06735/10 Pan-head cap screw M5x10, 10pcs. 66285 Reinforcing plate f. front axle Baja 4WD, 1pce.
06086 Rear shock absorber housing, 1pce. 06738/03 Self-locking hexagon nut, M3, 15pcs. 66285/01 Alloy distance SW 10x7, 2pcs.
06087 Upper shock plug M4, 2pce. 06738/04 Self-locking hexagon nut, M4, 15pcs. 66286 Plastic fixing plate front Baja 4WD, 1pce.
06087/01 Upper shock plug M5, 2pce. 06738/05 Self-locking hexagon nut, M5, 15pcs. 66287 Front alloy shock mount Baja 4WD, 1pce.
06088 Lower shock plug A+B, 2pcs. 06738/06 Self-locking hexagon nut, M6, 15pcs. 66288 Alloy brace long Baja 4WD, 2pcs.
06089 Shock piston 2-hole, 2pcs. 06739/03 Hexagon nut M3, 15pcs. 66304 Damper press. spring blue 2,1x100mm, 2pcs.
06092 Spring plate, 2pcs. 06739/05 Hexagon nut M5, 15pcs. 66305 Damper press. spring violet 2,2x100mm, 2pcs.
06093 Shock seal kit, 4pcs. 06745 Shim rings 10x16x1mm, 10pcs. 68140/01 Body Baja Buggy 4WD painted, 1pce.
06100/03 Turnbuckle right/left, 36 mm, 2pcs. 07058 Body screws, 15pcs. 68140/02 Rear Spoiler Baja Buggy 4WD painted, 1pce.
06112 M6 nuts with disk, 10pcs. 07087/01 Lower shock retaining, short 2pcs. 68150/01 Body Baja Buggy 4WD clear, 1pce.
06126 Brake rods compl./1:6, set 07091 Shock piston shaft long, 1pce. 68205 Plastic rear axle mount left 4WD, 1pce.
06134/01 Engine mount small/G230 RC/Marder, 1pce. 07100 Adjusting clips for front axle 16pcs. 68206 Plastic rear axle mount right 4WD, 1pce.
06137/01 Bolt f. gear unit 24,5/26,5mm, 3pcs. 07102 Front wishbone pin, 2pcs. 68213 Plastic damper plate rear 4WD, 1pce.
06268 Battery holder, 1pce. 07315 Clutch block carrier, 1pce. 68215 Plastic engine mount large 4WD, 1pce.
06350 Fuel tube, 1pce. 07315/01 Screw for carrier/Zenoah, 1pce. 68216 Gear shaft 4WD, 1pce.
06421/05 Polycarbonate rear spoiler f.1:6 OR, 1pce. 07316 Clutch blocks, 2pcs. 68220 Hous. f. plastic tension. pulley left 4WD, 1pce.
06427 Plastic gearwheel 46 teeth, 1pce. 07317/11 Clutch spring Ø G230/240/260/270, 1pce. 68221 Hous. f. plastic tension. pulley right 4WD, 1pce.
06432 Steel gearwheel 18 teeth, 1pce. 07318 Dowel screws f.clutch blocks/Zenoah, 2pcs. 68225 Rear upper plastic wishbone 4WD, 2pcs.
06445 Shock absorber collet, 8pce. 07328/05 Metal coating for standard plug cap, 1pce. 68240 Plastic RC-plate 4WD, 1pce.
06451/03 Air filt. adapt.f. Zen.G230/G260,CY23/26, 1pce. 07329/01 Silencer f. Marder/Zenoah, 1pce. 68246 Throttle rods 4WD compl., set
06451/04 O-rings f. air filter adapt.19x1,5/ 57x2,5 , 2pcs. 07330/08 Scews f. silencer M5x60, 2pcs. 68250 Plastic front axle housing left 4WD, 1pce.
06464/05 Foam filter oiled, 2pcs. 07331/06 Silicone tube 14x3x40, 2pcs. 68251 Plastic front axle housing right 4WD, 1pce.
06465 FG inlet air filter 1:6 OR complete, set 07332 Silencer gasket, 2pcs. 68252 Plastic toothed belt wheel 12t. 4WD, 1pce.
06465/01 Filter cover, 1pce. 07348 Tank complete/Zenoah, 1pce. 68253 Plastic deflection roller 16mm, 1pce.
Spare parts list for 1:6 Monster Truck, Item N°. Description Item N°. Description Item N°. Description
Monster Hummer, Monster Jeep 4WD/ 06185 Side body mounts, 2pcs. 06745 Shim rings 10x16x1mm, 10pcs. 66250/01 Guide f. front stabi 4mm 4WD, 2pcs.
1:6 Stadium Truck, Stadium Hummer, 06227/07 Monster Truck tires S 14mm glued, 2pcs. 07058 Body screws, 15pcs. 66254 Bearing shaft, 6x50mm, 1pce.
06228/07 Monster Truck tires M 14mm glued, 2pcs. 07071/01 Stabilizer 5mm rear, 1pce. 66255 Ball bearing 6x15x5, 4pcs.
Stadium Jeep 4WD 06230/07 Stadium Truck tires M/14mm glued, 2pcs. 07071/02 Plastic brace f.stabilizer long, 6pcs. 66256 Front plastic toothed belt wheel 42t. 4WD,1pce.
06231/07 Stadium Truck tires S/14mm glued, 2pcs. 07087/01 Lower shock retaining, short 2pcs. 66257 Front plastic stop disk left 4WD, 1pce.
06268 Battery holder, 1pce. 07091 Shock piston shaft long, 1pce. 66258 Plastic stop disk right 4WD, 1pce.
Item N°. Description 06350 Fuel tube, 1pce. 07100 Adjusting clips for front axle 16pcs. 66267 Wishbone thread rod M10/M8x66mm, 2pcs.
05014/05 Bolt for battery holder, 2pcs. 06427 Plastic gearwheel 46 teeth, 1pce. 07102 Front wishbone pin, 2pcs. 66271 Ball bearing 17x26x7, 2pcs.
05019/01 Pressure spring 0,4x5x25mm, 2pcs. 06432 Steel gearwheel 18 teeth, 1pce. 07154 Body mount adjustable, 1pce. 66284 Reinforcing plate f.fr.-axle Monst./Stad.4WD,1p.
06013 Body clips, 10pcs. 06445 Shock absorber collet, 8pce. 07154/01 Body mount adjustable 80mm, 1pcs. 66287/01 Front shock mount Monster/Stadium 4WD, 1p.
06020 Collets 2,1 mm, 5pcs. 06451/03 Air filt. adapt.f. Zen.G230/G260,CY23/26, 1pce. 07155 Body mount short, adjustable, 1pce. 66287/02 Headless pin M5x45mm, 2pcs.
06022/01 Flexible aerial and mount, 1pce. 06451/04 O-rings f. air filter adapt.19x1,5/ 57x2,5 , 2pcs. 07315 Clutch block carrier, 1pce. 66291/05 Lower shock retaining, long 4WD, 2pcs.
06026/01 Rods M4 x 51mm, 2pcs. 06464/05 Foam filter oiled, 2pcs. 07315/01 Screw for carrier/Zenoah, 1pce. 66304 Damper pressure spring blue 2,1x100mm,2pcs.
06028/01 Track rod right/left 1:6, 74mm, 2pcs. 06465 FG inlet air filter 1:6 OR complete, set 07316 Clutch blocks, 2pcs. 66305 Dampfer pressure spring violet 2,2x100mm,2p.
06029/07 Ball-and-socket joint for M6, 4pcs. 06465/01 Filter cover, 1pce. 07317/11 Clutch spring Ø G230/240/260/270, 1pce. 68205 Plastic rear axle mount left 4WD, 1pce.
06029/08 Ball-and-socket joint for M8, 4pcs. 06510/20 Oil for shock absorber 2000, 1pce. 07318 Dowel screws f.clutch blocks/Zenoah,2pcs 68206 Plastic rear axle mount right 4WD, 1pce.
06030 Steel balls 10 x 10,75, 4pcs. 06534/02 Throttle pivot post 2,1 mm, set 07328/05 Metal coating for standard plug cap, 1pce. 68213 Plastic damper plate rear 4WD, 1pce.
06031 Roll cage, 1pce. 06540 Receiver box, 1pce. 07330/08 Scews f. silencer M5x60, 2pcs. 68215 Plastic engine mount large 4WD, 1pce.
06033 Wing mount, 1pce. 06546 FG receiver battery NiCd 6V/1500mAh, 1pce. 07331/03 Silencer, 1pce. 68216 Gear shaft 4WD, 1pce.
06033/01 Body support, 1pce. 06546/04 Single storage batt. NiCd 1,2V/800mAh, 4pcs. 07331/04 Exhaust pipe bended, 1pce. 68220 Housing f. plastic tensioning pulley left 4WD,1p.
06034 Stiffening brace f. Monster Truck, 2pcs. 06548 Charger 220V/Fut., Hitec, 1pce. 07331/06 Silicone tube 14x3x40, 2pcs. 68221 Housing f.plastic tensioning pulley right 4WD,1p
06034/01 Plastic part f. stiffening brace, 2pcs. 06565/29 Cable clamps black, 4.8x290mm, 25pcs. 07331/07 Mount for exhaust, 1pce. 68225 Rear upper plastic wishbone 4WD, 2pce.
06036/05 FG ball bearing 10x19x7 w. grease fill., 2pcs. 06712/13 Counters.sh.met.screws 4.2x13mm, 20pcs. 07331/08 Silicone tube f. 7331/7, 2pcs. 68241 Plastic RC plate 4WD f. 9960MG, 1pce.
06037/01 Steel fixing plates, 2pcs. 06712/16 Counters.sh.met.screws 4.2x16mm, 20pcs. 07332 Silencer gasket, 2pcs. 68246 Throttle rods 4WD compl., set
06038 Engine mount washers, 4pcs. 06712/32 Counters.sh.met.screws 4,2x32mm, 20pcs. 07348 Tank complete/Zenoah, 1pce. 68250 Plastic front axle housing left 4WD, 1pce.
06039/11 Gear plate 09, 1pce. 06714/09 Pan-head tap.screws 2.9x9.5mm, 15pcs. 07352 Fuel tube/Zenoah, 1pce. 68251 Plastic front axle housing right 4WD, 1pce.
06039/12 GRP brake plate, 1pce. 06714/13 Pan-head tap.screws 2.9x13mm, 15pcs. 07353 Rubber gasket f. tank, 1pcs. 68252 Plastic toothed belt wheel 12t. 4WD, 1pce.
06040/05 FG ball bearing 10x22x6 w. grease fill., 2pcs. 06714/16 Pan-head tap.screws 2,9x16mm,15pcs. 07384 FG Zenoah engine G260RC 68253 Plastic deflection roller 16mm, 1pce.
06042/01 Brake square 97, new 1pce. 06714/19 Pan-head tap.screws 2,9x19mm, 15pcs. 07561 Hitec RCS Aggressor FM/DCX receiver, set 68265 Front lower plastic wishbone 4WD, 1pce.
06044/05 Metal brake disk, 1pce. 06716/09 Pan-head tap.screws 4,2x9.5mm, 15pcs. 08345 Coupling flange Zenoah 1:6, 1pce. 68266 Front upper plastic wishbone 4WD, 2pcs.
06045/01 Brake operating shaft 97 new, each 1pce. 06716/13 Pan-head tap.screws 4.2x13mm, 15pcs. 08456 Steel brake plates, 2pcs. 68268 Front lower wishbone pin 106mm, 2pcs.
06045/03 Brake lever 30mm, 1pce. 06716/16 Pan-head tap.screws 4.2x16mm, 15pcs. 08462/01 Plastic bush 4/6x5mm, 4pcs. 68270 Front plastic upright 4WD, 2pcs.
06047/01 Steel gearwheel 15theeth widened, 1pce. 06716/22 Pan-head tap.screws 4.2x22mm, 15pcs. 08523 Rear shock absorber set, long, 2pcs. 68271 Fixing nut f. front upright, 2pcs.
06049/01 Clutch bell, 1pce. 06716/32 Pan-head tap.screws 4.2x32mm, 15pcs. 26100/01 Body Monster/Stadium Truck 4WD white, 1pce. 68276 Front driving axle 4WD, 1pce.
06050 Plastic gear carrier 60 mm, 1pce. 06720/40 Rec.counters.head screws M4x40mm,10pcs. 26100/02 Front body Monst./Stad./Street Truck white,1p. 68277 Front driving shaft 4WD, 1pce.
06051 Dampening rubber, 4pcs. 06722/25 Rec.counters.head screws M5x25mm,10pcs. 26110/01 Body Monster/Stadium Truck 4WD yellow, 1pce 68323 Servo saver A/B, 1pce.
06052 Plastic gearwheel 48 teeth, 1pce. 06722/30 Rec.counters.head screws M5x30mm,10pcs. 26110/02 Front body Monst./Stad./Street Truck yellow,1p. 68324 Servo saver axle new, 1pce.
06063/05 FG ball bearing 12x28x8w. grease fill., 2pcs. 06722/35 Rec.counters.head screws M5x35mm,10pcs. 26150/01 Body Monst/Stad./ Truck 4WD transparent, 1p. 68325/01 Servo saver spring 2,4mm, 1pce.
06064 Differential housing, 1pce. 06723/16 Rec.counters.head screws M6x16mm, 10pcs. 26150/02 Front body Monst./Stad./Str.Truck transp., 1pc. 68326 Nut M10 f. servo saver, 1pce.
06066/02 Diff. gearwheel A reinforced, 2pcs. 06724/08 Sock. head cap screws 8.8,M3x8mm,10pcs. 26155 Model stickers f.Monster/Stad. Truck 4WD, set 68327 Tension sleeve f.servo saver new, 1pce.
06067/02 Diff. gearwheel B reinforced, 2pcs. 06724/16 Sock. head cap screws M3x16mm,10pcs. 36110 Body Monster/Stadium Hummer H2 yellow,1p.
06068 Bevel differential gear axle, 1pce. 06724/18 Sock. head cap screws 8.8 M3x18mm,10pcs. 36130 Body Monster/Stadium Hummer H2 black, 1p.
06069/01 Diff. driving axle, pluggable, 1pce. 06725/14 Socket head cap screws M4x14mm,10pcs. 36150 Body Monster/Stadium Hummer H2 transp.,1p.
06072/02 Adj. rear lower wishbone Monster, 1pce. 06725/20 Socket head cap screws M4x20mm,10pcs. 36155 Model stickers for Hummer H2 4WD, set
06073 Rear lower wishbone pin, 2pcs. 06726/16 Socket head cap screws M5x16mm,10pcs. 46120 Body Monster/Stadium-Jeep 4WD, red, 1pce.
06075 Rear upper wishbone pin, 2pcs. 06726/25 Socket head cap screws M5x25mm,10pcs. 46130 Body Monster/Stadium-Jeep 4WD, black, 1pce.
06077 Rear upright raised l./r., 2pcs. 06726/40 Socket head cap screws M5x40mm,10pcs. 46150 Body Monster/Stadium Jeep 4WD transp.,1p.
06077/05 Steel ball 10x13 for rear upright, 2pcs. 06727/10 Socket head cap screws M6x10mm, 5pcs. 46155 Model stickers for Jeep 4WD, set
06077/08 Distance bush for rear upright, 2pcs. 06727/40 Socket head cap screws 8.8,M6x40mm, 5pcs. 60230 Front bumper Baja, 1pce.
06078/05 FG ball bearings 8x22x7 w. grease fill., 2pcs. 06728/03 Headless pin M3x3mm, 15pcs. 60239 Plastic brace long, 2pcs.
06079 Rear driving axle, 1pce. 06729/30 Headless pin M4x30mm, 15pcs. 60239/01 Plastic brace short, 2pcs.
06080 Rear dogbone, 1pce. 06730/05 Headless pin M5x5mm, 15pcs. 66200 Alloy chassis 4WD, 1pce.
06081/01 Ball 5/10x15 M5, 4pcs. 06730/16 Headless pin M5x16mm, 15pcs. 66207 Plastic gear disk rear 42t. 4WD, 1pce.
06086 Rear shock absorber housing, 1pce. 06730/25 Headless pin M5x25mm, 15pcs. 66208 Steel gear wheel 48t. 4WD, 1pce.
06087/01 Upper shock plug M5, 2pce. 06730/30 Headless pin M5x30mm, 15pcs. 66210 Rear axle cover 4WD, 1pce.
06088 Lower shock plug A+B, 2pcs. 06731/08 Tallow-drop screw M4x8mm, 15pcs. 66211 Gear wheel protection 4WD, 1pce.
06089 Shock piston 2-hole, 2pcs. 06731/14 Tallow-drop screw M4x14mm, 15pcs. 66212 Alloy connection rod gear 4WD, 1pce.
06092 Spring plate, 2pcs. 06732/03 Retain.washers-spring steel,3.2mm, 15pcs. 66217 Steel gear wheel 14t. narrow, 1pce.
06093 Shock seal kit, 4pcs. 06732/05 Retain.washers-spring steel, 5mm, 15pcs. 66218/01 Basic body f. inlet silencer, 1pce.
06100/03 Turnbuckle right/left, 36 mm, 2pcs. 06732/07 Retain.washers-spring steel, 7mm, 15pcs. 66222 Bearing shaft f.tension. pulley housing 4WD,1p.
06112 M6 nuts with disk, 10pcs. 06733/06 Headless pin, M6x6mm, 15pcs. 66223 Plastic bearing seat 4WD, 2pcs.
06126 Brake rods compl./1:6, set 06734/04 Washers, steel 4.3mm, 15pcs. 66226 Wishbone thread rod M10/M8x84mm, 2pcs.
06134/01 Engine mount small/G230 RC/Marder, 1pce. 06734/05 Washers, steel 5.3mm, 15pcs. 66230 Alloy square wheel driver 14mm/M6, 2pcs.
06137/01 Bolt f. gear unit 24,5/26,5mm, 3pcs. 06734/06 Washers, steel 6.4mm, 15pcs. 66230/05 Square wheel driver 14mm/M6 steel, 2pcs.
06175 Body support Monster models, 1pce. 06735/10 Pan-head cap screw M5x10, 10pcs. 66235 Lower part belt channel, 1pce.
06176 Dampening rubber f. body support, 4pcs. 06738/03 Self-locking hexagon nut, M3, 15pcs. 66236 Upper part belt channel, 1pce.
06183 Left alloy side plate, 1pce. 06738/04 Self-locking hexagon nut, M4, 15pcs. 66237 Toothed belt, 1pce.
06183/01 Alloy distance 8x27/ 10x34, 2pcs. 06738/05 Self-locking hexagon nut, M5, 15pcs. 66238/01 Lower tank mount 4WD, 1pce.
06183/02 Socket head cap screw M6x75mm, 1pce. 06738/06 Self-locking hexagon nut, M6, 15pcs. 66238/02 Upper tank mount 4WD, 1pce.
06183/03 Socket head cap screw M4x45mm, 2pcs. 06739/03 Hexagon nut M3, 15pcs. 66244 Ball-and-socket joint 7mm f.M4, 8pcs.
06184 Right alloy side plate, 1pce. 06739/05 Hexagon nut M5, 15pcs. 66245 Steel ball 7mm, 4pcs.
1:6 MONSTER/STADIUM TRUCK/ HUMMER/ JEEP 4WD
Exploded view for
1:6 Monster Truck, Monster Hummer, Monster Jeep 4WD
1:6 Stadium Truck, Stadium Hummer, Stadium Jeep 4WD
26100/02
26110/02 36155
26150/02 26155 46155
2 06734/04 06183/03
6/3 01
3
71 06
06
06230/07 06714/09 06183/01
1
4/0 18
4
603 07155 06
0 Hummer/Jeep
06185
Truck 06716/13
4
06716/16 03
06
06176 06714/09 8
1/0
73
06734/04 06
08462/01 01
34/
060
067
8
1/0
73
16/
06
32
16
12/
061
067
75
68241 66200
06013
16 06183/01
16/
067
07154/01
Hummer 66287/01
07154 02 06183/02
87/
Truck/Jeep 662
68251
05
06738/05 39/ 58
662
067 662
06183
84
662
56
08523 06738/04 40 13
065 14/
66305
06726/16 067
53
682 06712/16
662
067
52 19
682 14/
54
57 067
662
06734/05
662
20/
40
54
68324 06022/01
060
55 07102
14 662
64
06714/09
067
5 1
6/0
060
63/0
04
32/0 0
682
067
07
682
0 66244
28/ 71 25/2
76
50
06714/16
6 68 06029/07
69/
682 06730/16
16/1 68323
067 5 06714/19
662
4/0
01
73
06
67
060
682
06734/04 1 68271
50/0
662 68325/01
28/
65
68270 06722/30
01
06029/07
060
06731/08
68277 06078/05 06733/06
29/
06734/04 68326
08
66230 06725/20
60230 06734/06
06081/01 06735/10
06112 06738/04
06714/13 06738/06 06081/01 06030
06087/01 08523 Set
07384 06712/13 06712/16
06093
66218/01 06464/04 66305 66304
8 06451/03 06465/01
30/0 06451/04 06464/05
073 34/05 06465-Set 06086
067
06712/13
06738/05 06089
06726/40 06445
06716/13 38
73 32 06734/04 060 06134/01 06723/16
0
/13 66217
08345
71 6 06088
06
07091
07331/07
06730/05 06093
07331/03 1 /04 07331/08 66211
06716/32 06732/03
6 073 3
73 31/0 6 06734/04
0 4 06092
682 06036/05
06728/03
19/01 06020 06093 06088
050
06126
07315 06037/01 68216
06565/29 15 05724/08
682 07087/01 66291/05
06020 07315/01 06716/13 06042/01 06045/03
1 038
06534/02 07316 6 137/0 06
06728/03 0 06712/16 06039/12
06738/03 07317/11 06724/08
06044/05
06739/03 06732/05
07318 06036/05
06745 08456 06045/01
/11
06049/01 06039
06137/01 06050
06724/18
06734/06 06051
06040/05
06730/05 06732/07
06432 Stadium 06727/40
06047/01 Monster 06732/07 06427 Stadium
06052 Monster
06725/20
06175 06013
66210 07154
06176 06013
067 12
662
2
04
06730/3 06033
0
36
662 06231/07
60239/01
06712/16 06033/01
06
35 66258
662
73
8/
66207
04
68
06725/20
20
6
662 66304
30/2
75
060
067
06729/30
06712/16 06073 06080 06227/07
06350 06036/05
68225 06732/05
07353 66222 06078/05
06
71
01
38/
662
6
07352 06079
06734/05 06077/08
68220 06078/05
06734/04 06077/05 06733/06
07348 06029/08 06734/06
66238/02 66230/05
06712/16 06731/14 06722/35 06738/06 06112
Ersatzteilliste/ Spare parts list 7374 Vergaserhebel, 1 St. 7313/8 Crankshaft complete, 1 pce. 7339/8 Screws f.carb./G230/260RC,CY, 2pcs. 7385/1 Cylinder 26 ccm, 1 pce.
7375 Schraube f. Vergaserhebel, 1 St. 7313/1 Key for crankshaft, 1 pce. 7340/8 Circuit breaker/G230/260RC,CY,1pce. 7385/2 Piston 26 ccm, 1 pce.
7377/8 Choke-Welle m. Schraube, 2 St. 7314 Hexagon nut, 1 pce. 7341/8 Engine housing A, 1 pce. 7385/3 Piston ring 26 ccm, 1 pce.
7300/9 Zenoahmotor G230RC/04 7378/8 Choke-Klappe, 1 St. 7315 Clutch block carrier, 1 pce. 7342/8 Engine housing B, 1 pce. 7385/4 Gudgeon pin 26 ccm, 1 pce.
7384 Zenoahmotor G260RC 7379/8 Choke-Hebel, 2 St. 7315/1 Screw for carrier, 1 pce. 7343/8 Spark plug G230 RC,CY, 1pce. 8344/1 Coupling flange Solo/Zeno horizontal
7301/8 Kurbelgehäuse A+B, 1 St. 7385/1 Zylinder 26 ccm, 1 St. 7316 Clutch blocks, 2 pcs. 7344/8 Cable bush./G230/260RC,CY, 1pce. 8345 Coupling flange Zenoah vertical
7303/8 Dichtring, 2 St. 7385/2 Kolben 26 ccm, 1 St. 7317/8 Clutch spring, 1 pce. 7354/8 Spacer block/G230RC,CY, 1 pce.
7304/2 Kugellager, 2 St. 7385/3 Kolbenring 26 ccm, 1 St. 7318 Dowel screws f. clutch blocks, 2 pcs. 7355/8 Carburetor/G230/260RC,CY, 1pce.
7305/8 Kurbelgehäusedichtung, 1 St. 7385/4 Kolbenbolzen 26 ccm, 1 St. 7319/8 Cooling fan/G230/260RC,CY, 1pce. 7356/8 Air filter/G230/260RC,CY, 1pce.
7306/8 Zylinder-Fußdichtung, 1 St. 8344/1 Kuppl.-Flansch Zen. liegend, 1 St. 7323/8 Pull start unit/G230/260RC,CY, 1pce. 7357 Air filter foam, Zenoah,CY 2pcs.
7307/9 Zylinder G230/04,1St. 8345 Kuppl.-Flansch Zen. stehend, 1 St. 7323/9 Starter hous./G230/260RC,CY, 1pce. 7361/8 Needle(full-speed)/ spring, 2 pcs.
7307/10Tun.-Zylinder f. FG Zenoah02 ,1St. 7323/10 Spring assem./G230/260RC,CY, 1pce. 7362/9 Needle(idle speed)/spring G230/04,2pcs.
7308/9 Kolben G230/04, 1 St. 7300/9 Zenoah engine G230RC/04 7323/11 Rope pulley/G230/260RC,CY, 1pce. 7363 Diaphragm, 2 pcs.
7309/9 Kolbenring G230/04, 1 St. 7384 Zenoah engine G260RC 7323/12 Rope/G230/260RC,CY, 1pce. 7364 Carburetor cover, 1 pce.
7310 Kolbenbolzen, 1 St. 7301/8 Crank case housing A+B, 1 pce. 7323/13 Starter handle/G230/260RC,CY, 1pce. 7365 Throttle screw /spring, 2 pcs.
7311 Kolbenbolzensicherung, 2 St. 7303/8 Seal ring, 2 pcs. 7323/14 Starter ratchet/G230/260RC,CY, 1pce. 7366/8 Valve, 1 pce.
7312 Nadellager kompl., 1 St. 7304/2 Bearings, 2 pcs. 7323/15 Press. spring/G230/260RC,CY, 1pce. 7368 Leg spring, 1 pce.
7312/1 Zentrierscheiben f. Nadellager, 2 St. 7305/8 Crankshaft gasket, 1 pce. 7323/16 Screw,disks/G230/260RC,CY, 3pcs. 7370 Diaphragm set, 2 pcs.
7313/8 Kurbelwelle kompl., 1 St. 7306/8 Cylinder gasket, 1 pce. 7326/8 Securing ring/G230/260RC,CY, 1pce. 7371 Plastic part with carb. nipple, 1 pce. FG Modellsport GmbH
7313/1 Keil für Kurbelwelle, 1 St. 7307/9 Cylinder G230/04, 1 pce. 7328/2 Spark plug cap, 1pce. 7372 Metal part f. pump, 1 pce. Spanningerstr. 2
7314 Sechskantmutter, 1 St. 7307/10 Tun.-Cylinder f. FG Zen. 02, 1 pce.7328/8 Ignition coil/G230/260RC,CY, 1 pce. 7372/1 Screws f. metal part, 4 pcs. 73650 Winterbach-Germany
7315 Mitnehmer f. Kuppl.-Backen, 1 St. 7308/9 Piston G230/04, 1 pce. 7330/8 Scews f.silencer M5x60/Zen.,CY,2pcs. 7373 Pump, 1 pce. Phone: +49 7181 9677-0
7315/1 Schraube f.Mitnehmer, 1 St. 7309/9 Piston ring G230/04, 1 pce. 7332 Silencer gasket /Zenoah,CY, 2pcs. 7374 Carburetor arm, 1 pce. Fax: +49 7181 9677-20
7316 Kupplungsbacken, 2 St. 7310 Gudgeon pin, 1 pce. 7334/8 Screw set engine 7375 Screw f. carburetor arm, 1 pce. info@fg-modellsport.de
7317/8 Kupplungsfeder, 1 St. 7311 Gudgeon pin clips, 2 pcs.
7318 Passschrauben f. K.-Backen 2 St.
7335 Insulator gasket/Zenoah,CY, 1pce. 7377/8 Choke shaft w. screw, 2 pcs. www.fg-modellsport.de
7312 Needle bearing, 1 pce. 7336 Insulator, 1 pce. 7378/8 Choke flap, 1 pce.
7319/8 Lüfterrad/G230/260RC,CY, 1St. 7312/1 Spacer washer, 2 pcs. 7337 Carburetor gasket/Zenoah,CY, 1pce. 7379/8 Choke lever, 2 pcs.
7323/8 Seilzugstartv. kpl./G230/260RC,CY,1St
7323/9 Startergehäuse/G230/260RC,CY, 1St. EL.7300-9-280906
7323/10Federkassette /G230/260RC,CY, 1St.
7323/11Seilrolle/G230/260RC,CY, 1St. ohne Abb.
7323/12Starterseil/G230/260RC,CY, 1St. 7328/2
Kerzenstecker 7343/8
7323/13Startergriff/G230/260RC,CY, 1St.
7323/14Starterklinke/G230/260RC,CY, 1St. 7323/13
7373
7323/15Druckfeder/G230/260RC,CY, 1St.
7323/16Schraube/ Scheib./ G230/260RC,CY, 3St. 7342/8
7372/1
7326/8 Sicherungsring/G230/260RC,CY, 1St.
7328/2 Zündkerzenstecker, 1 St. 7372 7307/9
7307/10 7340/8 7323/12 7323/16
7328/8 Zündspule/ G230/260RC,CY, 1St. 7357 7385/1
7330/8 Schrauben f.Schalld.M5x60/Zen.,CY 2St. 7371 7379/8
7356/8 7330/8
7332 Schalldämpferdichtung /Zenoah,CY, 2St. 7370 7378/8 7323/10
7334/8 Schraubensatz-Motor, Set 7377/8 7323/15
7335 Dichtung f. Isolator /Zenoah,CY, 1St.
7361/8 7374/7375
7336 Isolator, 1 St. 7362/9 7323/14
7337 Dichtung f. Vergaser /Zenoah,CY, 1St. 7355/8
7339/8 Vergaserschrauben/ G230/260RC,CY, 2St. 7334/8
7340/8 Aus-Schalter/ G230/260RC,CY, 1St. 7323/11
7341/8 Motorgehäuse A, 1 St. 7354/8 7332
7368 7337 7336 7335 7341/8
7342/8 Motorgehäuse B, 1 St. 7308/9
7343/8 Zündkerze/ G230 RC,CY, 1St. 7385/2
7363 7311
7344/8 Kabeldurchführung/ G230/260RC,CY, 1St. 7366/8 7367/8
7354/8 Distanzstück/ G230 RC,CY, 1St. 7309/9 7310
7339/8 7385/4
7355/8 Vergaser/ G230/260RC,CY, 1St. 7385/3 7323/9
7365 7364
7356/8 Luftfilter/G230/260RC,CY,kompl., 1St. 7365/9
7357 Luftfilter-Einsatz / Zenoah,CY, 2St. 7306/8
7361/8 Vollgasdüsennadel/ Feder, 2 St. 7328/8 7334/8
7315/1
7362/9 Leerlaufdüsennadel/ Feder G230/04, 2 St. 7334/8 7344/8
7363 Membrane-Satz, 2 St. 7315
7364 Vergaserdeckel, 1 St. 7317/8 7312/1 7312
7365 Standgasschraube/ Feder, 2 St.
7365/9 Standgasschr./Feder G230/260RC04, 2St. 7326/8 7304/2
7366/8 Drosselklappenwelle m. Schraube, 2 St. 7313/8 7314
7367/8 Drosselklappe, 1 St. 7316
7368 Schenkelfeder, 1 St.
7370 Membrane-Satz, 2 St. 7303/8 7313/9 7303/8
7371 Kunststoffteil m. Vergaser-Nippel, 1 St. 8344/1 7301/8 7319/8
7318
7372 Metallteil f. Pumpe, 1 St. 7305/8
8345 7334/8
7372/1 Schrauben für Metallteil, 4 St. 7301/8
7373 Pumpe, 1 St.