Académique Documents
Professionnel Documents
Culture Documents
Trademarks
IBM, VGA, and PS/2 are registered trademarks of International
Business Machines.
Intel, Pentium II/III, Pentium 4, Celeron and MMX are registered
trademarks of Intel Corporation.
Microsoft, MS-DOS and Windows 98/ME/NT/2000/XP are
registered trademarks of Microsoft Corporation.
PC-cillin is a trademark of Trend Micro Inc.
AMI is a trademark of American Megatrends Inc.
It has been acknowledged that other brands or product names in
this manual are trademarks or the properties of their respective
owners.
Copyright 2004
All Rights Reserved
M909G Series, V5.0
I845/August 2004
i
Table of Contents
Trademark ................................................................................... i
Static Electricity Precautions ............................................................ iii
Pre-Installation Inspection ................................................................ iii
Features and Checklist Translation .................................................... v
Pre-Installation Inspection
1. Inspect this mainboard whether there are any damages to
components and connectors on the board.
2. If you suspect this mainboard has been damaged, do not
connect power to the system. Contact your motherboard
vendor about those damages.
iii
Notice:
Owing to Microsofts certifying schedule is various to every
supplier, we might have some drivers not certified yet by
Microsoft. Therefore, it might happen under Windows XP that
a dialogue box (shown as below) pop out warning you this
software has not passed Windows Logo testing to verify its
compatibility with Windows XP. Please rest assured that our
RD department has already tested and verified these drivers.
Just click the Continue Anyway button and go ahead the
installation.
iv
Caractristiques
Fonction
Supporte: CPU FSB: 533/400MHz
Technologie Hyper-Threading
DDR333/266; USB2.0; Ultra ATA 100/66/33
Supporte:CPU FSB: 533*/400MHz
DDR266; USB2.0; Ultra ATA 100/66/33
Ne supporte pas: Technologie Hyper-Threading
*: Surfrquenage
Support de Mmoire
Deux logements DIMM 184 broches pour DDR SDRAM modules mmoire
Supporte les DDR jusqu 333MHz (845GV) ou le bus mmoire DDR266MHz
(845GL)
La mmoire maximum installe est 2Go
AC97 Codec
Conforme aux spcifications AC97 2.3
Codec Full-duplex avec vitesse dchantillonnage indpendante et variable
Mmoire tampon dEcouteurs Intgre, SNR jusqu 90db
6Ch DAC, supporte 6 canaux de sorties haut-parleurs
Support de gestion dalimentation avance
Logements dExtension
Le carte mre possde les caractristiques suivantes :
Un logement AGPro (reportez-vous la page 20 pour plus de dtails)
Trois slots PCI 32 bits
Un slot CNR (Communications and Networking Riser)
Supporte matrise de bus Ultra DMA IDE avec vitesse de transfert de 100/
66/33 Mo/sec
vi
Ausstattung
Untersttz Socket-478-Prozessoren
Untersttzung fr Intel Pentium 4-CPUs mit/ohne Hyper-Threading-Technologie
Untersttzung von bis zu 533/400 MHz Front-Side Bus
Chipsatz
Der Intel 845GV/GL-Chipsatz verfgt ber den Intel 82845 Memory Control Hub
und den Intel 82801DB I/O Controller Hub (ICH4). Die Chipsatzarchitektur ist
in einem innovativen und skalierbaren Design gehalten und verspricht sowohl
Zuverlssigkeit als auch Leistungsstrke. Unten stehend finden Sie eine Liste mit
den Chipsatzteilen und deren jeweiligen Funktionen:
Northbridge
845GV
845GL
Funktion
Speicheruntersttzung
Zwei 184-pin DIMM Steckpltze fr DDR SDRAM Speichermodule
Untersttzung fr DDR bis zu 333MHz (845GV) oder DDR266MHz (845GL)
Speicherbus
Maximal auf 2GB Speicher erweiterbar
AC97 Codec
Entspricht AC97 2.3
Vollduplex-Codec mit unabhngiger und variabler Abtastrate
Integrierter Kopfhrer-Buffer, SNR bis zu 90db
6Ch DAC, untersttzt 6-Kanal-Lautsprecherausgang
Untersttzung fr Advanced Power Management
Erweiterungssteckpltze
Das Motherboard verfgt ber die folgenden Erweiterungsoptionen:
Ein AGPro-Slot (siehe Seite 20 fr mehr Details)
Drei 32-Bit PCI-Steckpltze
Ein CNR-Steckplatz (Communications and Networking Riser)
Untersttzung fr IDE Ultra DMA-Busmastering mit Transferraten von 100/66/
33 MB/Sek
vii
viii
Lista
Caratteristiche
Funzione
Supporta: CPU FSB: 533/400MHz
Tecnologia Hyper-Threading
DDR333/266;USB2.0; Ultra ATA 100/66/33
Supporta: CPU FSB: 533*/400MHz
DDR266 ; USB2.0; Ultra ATA 100/66/33
Non supporta: Tecnologia Hyper-Threading
*: Overclocking
Memoria Supporta
Due slot DIMM a 184 pin per moduli di memoria DDR SDRAM
Supporta DDR fino a 333MHz (845GV) o bus di memoria DDR266MHz
(845GL)
Quantit massima di memoria installabile, 2GB
AC97 Codec
Conforme con le specifiche AC`97 2.3
Codec full-duplex con frequenza di campionamento indipendente
e variabile
Memoria tampone integrata per auricolare, SNR fino a 90db
6 CanDAC, supporto di 6 uscite per le casse
Supporto per gestione energetica avanzata.
Opzioni di espansione
La scheda madre dotata delle seguenti opzioni di espansione:
Uno slot AGPro (fare riferimento alla pagina 20 per ulteriori dettagli)
Tre slot a 32-bit PCI
Uno slot CNR (Communications and Networking Riser)
Supporta gestione di canali IDE Ultra DMA con percentuali di campionamento
di 100/66/33/MB/sec.
ix
Caractersticas
Funcin
Soporta: CPU FSB: 533/400MHz
Tecnologa Hyper-Threading
DDR333/266; USB2.0; Ultra ATA 100/66/33
Soporta: CPU FSB: 533*/400MHz
DDR266 ; USB2.0; Ultra ATA 100/66/33
No soporta: Tecnologa Hyper-Threading
*: Sobre-cronometraje
Soporte de Memoria
Dos ranuras 184-pin DIMM para mdulos de memoria DDR SDRAM
Soporta DDR hasta bus de memoria de 333MHz (845GV) o DDR266MHz
(845GL)
Memoria mxima instalada es 2GB
AC97 Codec
Conforme con la especificacin AC97 2.3
Full-duplex Codec con ndice de muestreo independiente y variable
Buffer de Audfono Incorporado, SNR hasta 90db
6Ch DAC, soporte de altoparlante de 6 canales
Soporte de administracin de energa avanzada
Ranuras de Expansin
La placa principal viene con las sigtes. opciones de expansin:
Una ranura AGPro (refiera a la pg 20 para ms detalles)
Tres ranuras 32-bit PCI
Una ranura CNR (Communications and Networking Riser)
Soporta mastering de bus IDE Ultra DMA con ndices de transferencia de
100/66/33 MB/seg
xi
xii
Caractersticas
Funo
Suporta: CPU FSB: 533/400MHz
Teconologia Hyper-Threading, DDR333/266
USB2.0; Ultra ATA 100/66/33
Suporta: CPU FSB: 533*/400MHz
DDR266; USB2.0; Ultra ATA 100/66/33
No suporta: Teconologia Hyper-Threading
*: Overclocking
Suporte de memria
Dois sockets DIMM com 184 pinos para mdulos de memria DDR SDRAM
Suporta no mximo DDR at 333MHz (845GV) ou bus de memria
DDR266MHz (845GL)
A memria mxima instalada de 2GB
AC97 Codec
Compatvel com a especificao AC97 2.3
Full-duplex Codec com razo de amostra varivel independente
Buffer de Fone de Ouvido embutido, SNR at 90db
6 canais DAC, suporta 6 canais de altifalantes
Suporte de gerenciamento de fora avanado
Slots de expanso
A placa principal possui as seguintes slots de expanso:
Uno slot AGPro (fare riferimento alla pagina 20 per ulteriori dettagli)
Trs encaixes 32-bit PCI slots
Um encaixe para CNR (Communications and Networking Riser)
Suporta IDE Ultra DMA bus mastering com razo de transferncia de 100/66/
33 MB/seg
xiii
xiv
IDE
CD
Socket-478
/ Intel Pentium 4 CPU
533/400 MHz
845GV
845GL
*:
AC'97
AC97 2.3
SNR 90db
6DAC6
1 AGPro 2
3 32 PCI
(CNR)
IDE Ultra DMA 100/66/33 MB/sec
xv
LAN ()
(IEEE 802.3x)
USB 2.0
3 UHCI 6
1 EHCI USB 2.0 6
1 USB 2.0
S1-S5
/
xvi
Chapter 1: Introduction
Chapter 1 Introduction
This motherboard has a Socket-478 supporting Intel Pentium 4/
Prescott with Hyper-Threading Technology processors with
Front-Side Bus (FSB) speeds up to 533/400 MHz. HyperThreading Technology, designed to take advantage of the
multitasking features in Windows XP, gives you the power to do
more things at once.
Note: It supports Hyper-Threading Technology only when the
Intel 845GV is installed. Intel 845GL supports FSB 533 MHz
only by overclocking.
Key Features
The key features of this motherboard include:
Socket-478 Processor
Supports Intel Pentium 4 series CPU with/without
Hyper-Threading Technology
Supports up to 533/400 MHz Front-Side Bus
Chipset
There are Intel 845GV/GL chipsets that contain Intel 82845
Memory Controller Hub and Intel 82801 I/O Controller
Hub(ICH4) in accordance with an innovative and scalable
architecture with proven reliability and performance. Here is a list
of the chipset arrangement and their respective features:
Northbridge
845GV
845GL
Function
Support: CPU FSB: 533/400MHz
Hyper-Threading Technology
DDR333/266; USB2.0; Ultra ATA 100/66/33
Support: CPU FSB: 533*/400MHz
DDR266; USB 2.0; Ultra ATA 100/66/33
Doesnt support:Hyper-Threading Technology
* Supports FSB 533 MHz only by over-clocking
Memory Support
Two 184-pin DIMM sockets for DDR SDRAM memory
modules
Chapter 1: Introduction
AC97 Codec
Compliant with AC97 2.3 specification
Full-duplex Codec with independent and variable sampling
rate
Earphone Buffer Built-In, SNR up to 90db
6Ch DAC, support 6-channel speak-out
Advanced power management support
Expansion Options
The motherboard comes with the following expansion options:
USB 2.0
Includes three UHCI host controllers that support six
external ports
New: Includes one EHCI high-speed USB 2.0 Host Controller that supports all six ports
New: Supports a USB 2.0 high-speed debug port
Supports wake-up from sleeping states S1-S5
Supports legacy keyboard/mouse software
BIOS Firmware
This motherboard uses AMI BIOS that enables users to configure
many system features including the following:
Power management
Wake-up alarms
CPU parameters and memory timing
CPU and memory timing
Chapter 1: Introduction
Package Contents
Your motherboard package contains the following items:
The motherboard
The Users Guide
One diskette drive ribbon cable (optional)
One IDE drive ribbon cable
Software support CD
Optional Accessories
You can purchase the following optional accessories for this
motherboard.
Note: You can purchase your own optional accessories from the
third party, but please contact your local vendor on any issues
of the specification and compatibility.
Motherboard Components
Socket-478
ATX1
DDR1/2
PW1
IO
PORTS
CPU FAN
IDE2/1
AGP1
SIR1
JP2
AUDIO2
PLED1
CHS FAN
CD1
LABEL
DDR1-2
IDE1/2
ATX1
PW1
USB3
FLOPPY
PANEL1
CHS FAN
JP2
SPKR1
CD1
PLED1
CN R1
PCI1-3
FLOPPY
SPKR1
PANEL1
COMPONENTS
Two 184-pin DDR SDRAM sockets
Primary/Secondary IDE connectors
Standard 4-Pin ATX Power connector
Standard 20-Pin ATX Power connector
Front Panel USB header
Floppy Disk Drive connector
Front Panel Switch/LED header
System Fan connector
Clear CMOS jumper
Speaker header
Analog Audio Input header
Power-On indicator header
USB3
LABEL
SIR1
PCI 1-3
AUDIO2
CPUFAN
CNR1
AGP1
COMPONENTS
Infrared Port header
32-bit PCI slots
Front Panel Audio header
CPU Fan connector
Communications Networking Riser slot
AGPro slot *See page 21 for details
I/O Ports
The illustration below shows a side view of the built-in I/O ports
on the motherboard.
(Optional)
1
CPUFAN
Socket-478
DDR1 DDR2
10
3.
4.
11
Jumper Settings
Connecting two pins with a jumper cap is SHORT; removing a
jumper cap from these pins, OPEN.
1
JP2
12
ATX1
1
PW1
CHS FAN
1
PANEL1
Connect the power connector from the power supply to the PW1
connector on the motherboard. The ATX1 is a +12V connector
for CPU Vcore power.
If there is a cooling fan installed in the system chassis, connect the
cable from the cooling fan to the CHS FAN fan power connector
on the motherboard.
Connect the case switches and indicator LEDs to the PANEL1
header.
13
Pin
Signal
2 FP PWR/SLP(+)
4 FP PWR/SLP(-)
6 POWER_SW_P(+)
8 POWER_SW_N(-)
10 KEY
SIR1
1
1
PLED1
1
AUDIO2
1
SPKR1
1
USB3
14
1.
2.
3.
Pin
2
4
6
8
10
Signal
VERG_FP_USBPWR0
USB_FP_P1(-)
USB_FP_P1(+)
GROUND
USB_FP_OC0
15
Signal
GROUND
NC
POWER
1.
2.
Pin
2
4
6
Signal
KEY
GND
IRRX
16
IDE2 IDE1
FLOPPY
1
17
IDE Devices
IDE devices include hard disk drives, high-density diskette drives,
and CD-ROM or DVD-ROM drives, among others.
The motherboard ships with an IDE cable that can support one or
two IDE devices. If you connect two devices to a single cable,
you must configure one of the drives as Master and one of the
drives as Slave. The documentation of the IDE device will tell you
how to configure the device as a Master or Slave device. The
Master device connects to the end of the cable.
Install the device(s) and connect power from the system power
supply. Use the cable provided to connect the device(s) to the
Primary IDE channel connector IDE1 on the motherboard.
If you want to install more IDE devices, you can purchase a
second IDE cable and connect one or two devices to the Secondary IDE channel connector IDE2 on the motherboard. If you
have two devices on the cable, one must be Master and one must
be Slave.
18
CD1
When you first start up your system, the BIOS should automatically detect your CD-ROM/DVD drive. If it doesnt, enter the
Setup Utility and configure the CD-ROM/DVD drive that you
have installed. On the motherboard, locate the 4-pin header CD1.
Pin
1
2
3
4
Signal
CD IN L
GND
GND
CD IN R
19
Expansion Slots
This motherboard has one AGPro, one CNR and three 32-bit PCI
slots.
AGP1
PCI1
PCI2
PCI3
CNR1
20
AGP 4X/8X
ATI
4X
8x
NVIDIA
4X
SIS
8X
8X
CHIPSET
ATI Radeon 8500
ATI Radeon 9000 PRO
ATI Radeon 9200
ATI Radeon 9200
ATI Radeon 9500
ATI Radeon 9700 PRO
ATI Radeon 9800 PRO
ATI Radeon 9800 XT
TNT2 M64
GeForce 256
GeForce 256 DDR
GeForce 2 GTS
GeForce 2 GTS
GeForce 2 MX
GeForce 2 MX
GeForce 2 MX
GeForce 2 Ultra
GeForce 2 MX200
GeForce 2 MX400
GeForce 3
GeForce 3
GeForce 3 Ti500
GeForce 4 MX420
GeForce 4 MX440
GeForce 4 Ti4200
GeForce 4 Ti4400
GeForce 4 Ti4600
GeForce 4 Ti4200
GeForce 4 MX440
GeForce 4 MX4000
GeForce FX5200
GeForce FX5600
GeForce FX5700
GeForce FX5800
GeForce FX5900Ultra
GeForce FX5950Ultra
Xabre 200
Xabre 200
Xabre 400
Xabre 400
MANUFACTURE
ATI RADEON 8500 DDR
Gigabyte GV-R9000 PRO
ECS R9200LE / 64M
ECS R9200LE / 128M
Power Color ATI 9500
Power Color ATI 9700Pro
MIC Radeon9800Pro/128M
ECS 9800XT
Win Fast S325
Creative CT6940
ASUS V6800
Gigabyte GA-66032D
ELSA GLADIAC GTS DDR PRO/64M
ASUS AGP-V7100
ELSA Gladiac MX
Triplex Mohock
WINFAST GeForce 2 Ultra
Triplex-MX2200
ELSA GLADIAC 511
ELSA GLADIAC 920
ASUS V8200
ASUS V8200
WINFAST A170TH SDR
ASUS V8170DDR
WINFAST A250TD/64M
ELSA 725DVI
ELSA 925ViVo
ASUS V9280TD
ASUS V9180VS
WinFast A180B
ASUS V9520 Magic
ELSA FX 732
ELSA FX 736
Triplex FX5800TD
MSI FX5900Ultra
ELSA FX938Ultra
ECS AG200E4-D32
ECS AG200T8_D64
ECS AG400T8_D64
ECS-MM AG400T8_D64
Note: Please visit our website for the updated AGP graphics
card support list : Http://www.pcchips.com/support/FAQ
21
22
PCI Slot
You can install the 32-bit PCI interface expansion cards in the
slots.
CNR Slot
This slot is used to insert CNR (Communications and Networking
Riser) cards including LAN, Modem, and Audio functions.
Dual Monitor
In order to enable Dual Monitor Function, users must have
Two Monitors, Two Graphics Devices (one is for AGP
graphics card; the other one is for onboard VGA) and Windows
2000 or Windows XP that supports the Dual Monitor Function.
Users must follow the Dual Monitor Installation below or visit
our website at Http://www.pcchips.com/support/FAQ for
detailed information.
Dual Monitor Installation (For Windows XP)
If the onboard VGA is first installed, and you would like to use the
add-on AGP card. Please follow the installation steps 1-6. Users
may go to step 4 directly if the add-on AGP card is installed first
and then turned on the onboard VGA devices for secondary
display.
Step 1: Remove the Onboard VGA Driver
Go to Control Panel
Choose Add or Remove Programs
Choose Intel Extreme Graphics Driver
Click Remove
Shut down the computer
23
24
25
26
27
MEMO
28
29
Features Setup
CPU PnP Setup
Hardware Monitor
Change Password
Exit
Esc:Quit
:Select Item (Shift) F2: Change Color
F5: Old Values
F6: Optimal Values
F7: Best Performance Values
F10: Save&Exit
Standard COMOS setup for changing time, date, hard disk type, etc.
32Bit
Mode
On
On
On
On
ESC : Exit
: Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
F3 : Detect All HDD
31
Quick Boot
If you enable this item, the system starts up more quickly be
elimination some of the power on test routines.
1st Boot Device/2 nd Boot Device/3rd Boot Device
Use these items to determine the device order the computer
uses to look for an operating system to load at start-up time.
Try Other Boot Device
If you enable this item, the system will also search for other
boot devices if it fails to find an operating system from the first
two locations.
32
33
Yes
Enabled
Disabled
Disabled
15
12
30
30
Disabled
Disabled
N/A
ESC:Quit
:Select Item
F1 :Help
PU/PD/+/-:Modify
F5 :Old Values
(Shift)F2:Color
F6 :Load Optimal Values
F7 :Load Best Performance Values
36
37
38
OnBoard FDC
This item enables or disables the onboard floppy disk drive
interface.
OnBoard Serial Port A
These items enable or disable the onboard COM1 serial port, and
to assign a port address.
OnBoard IR Port
This item enables or disables the Infrared port, and assigns a port
address. If you select a specific address, the resources are
assigned to the IR port, and you can use these items below to
determine the operation of the IR port.
OnBoard Parallel Port
This item enables or disables the onboard LPT1 parallel port, and
to assign a port address. The Auto setting will detect and
available address.
39
INTEL P4
1.536V
20.0x
100Mhz
ESC:Quit
:Select Item
F1 :Help
PU/PD/+/- : Modify
F5 :Old Values (Shift)F2 : Color
F6 :Load Optimal Values
F7 :Load Best Performance Values
41
1.536 V
3.232 V
5.085 V
11.437V
4.848 V
3.120 V
0 RPM
3309 RPM
35C/95F
43C/109F
ESC:Quit
:Select Item
F1:Help
PU/PD/+/-:Modify
F5:Old Values
(Shift)F2:Color
F6:Load Optimal Values
F7:Load Best Performance Values
42
Change Password
If you highlight this item and press Enter, a dialog box appears that
you can enter a Supervisor password. You can enter no more than
six letters or numbers. Press Enter after you have typed in the
password. There will be the second dialog box asking you to
retype the password for confirmation. Press Enter after you have
retyped it correctly. Then, the password is required for the access
to the Setup Utility or for it at start-up, depending on the setting of
the Password Check item in Advanced Setup.
Exit
Highlight this item and press Enter to save the changes that you
have made in the Setup Utility configuration and exit the program.
When the Save and Exit dialog box appears, press Y to save and
exit, or press N to exit without saving.
43
44
Once any of the installation procedures start, software is automatically installed in sequence. You need to follow the onscreen
instructions, confirm commands and allow the computer to restart
as few times as needed to complete installing whatever software
you selected. When the process is finished, all the support software will be installed and start working.
46
47
Hyper-Threading CPU
You must update BIOS to initiate BIOS Hyper-Threading Function and use HT CPU function under WinXP Operating System; if
not, please disable this option.
When BIOS detects the HT CPU, it shows the HyperThreading Function (default Disabled) option, which you
must set Enabled if you want to test HT CPU function. If
there is no HT CPU, this option is hidden and default
Disabled.
48