Académique Documents
Professionnel Documents
Culture Documents
Introduction
The Diagnostic Tester now incorporates a Key Code Utility Menu capable of performing
the following tasks for immobilizer functions:
S Key Code Registration
S Key Code Erasure
S AutoRegistration Closure
The Diagnostic Tester now incorporates a Key Code Utility Menu capable of performing
the following tasks for immobilizer functions:
Affected
Vehicles
Parts
Information
PART NUMBER
PART NAME
01001270
01001895005
NOTE:
Replacement Diagnostic Tester Kits or Software Cards may be ordered by calling OTC
at 18009338335.
Function
Description
(Key Code
Utility)
Key Registration
This function allows the registration of additional key codes for transponder keys
(Master/Sub Keys) using a Registered Master Key.
Key Code Erasure
This function allows the user to erase all the key codes for transponder keys except
the Registered Master Key used during this function.
Auto Registration Closure
This function allows the user to close Auto Registration Mode when less than three
keys have been registered.
NOTE:
When a new ECU is installed, it is in the Auto Registration Mode from the factory.
This allows Transponder Keys to automatically register as they are inserted into the
Ignition Cylinder. After three Transponder Keys are registered, the ECU closes Auto
Registration Mode. See the Repair Manual for further details.
Warranty
Information
OP CODE
DESCRIPTION
TIME
OPN
T1
T2
N/A
Page 1 of 9
Technical Service
Information Bulletin
SS00699
Title:
Operation
Procedures
This section provides the procedures necessary to access the IMMOBILIZER KEY CODE
UTILITY functions. Refer to the instructions below.
Verify
Immobilizer
Key Type
Before any IMMOBILIZER KEY CODE UTILITY function can be performed, the type of
Transponder Key must be verified. The following steps show how to verify the
Transponder Key type.
1. Connect the Diagnostic Tester to DLC3 and press the (ON) key.
2. Insert a Registered Master Key (Black Key Head) into the ignition key cylinder and
turn to the ON position.
HINT:
A Registered Master Key is required for KEY REGISTRATION, KEY CODE ERASURE,
and AUTO REGISTRATION CLOSURE. A Sub Key (Grey Key Head) will not perform
these functions.
Page 2 of 9
[NO]
NOTE:
If the Transponder Key is a Master Key, proceed to [4: KEY CODE UTILITY] by
pressing the (EXIT) key back to the DIAGNOSTIC MENU IMMOBILIZER (Screen C).
From the DIAGNOSTIC MENU IMMOBILIZER (Screen C), select [4: KEY CODE
UTILITY]
Page 3 of 9
Verify
Immobilizer
Key Type
(Continued)
Key
Registration
This function allows the registration of additional Key Codes for Transponder Keys
(Master/Sub Keys) using a Registered Master Key. The following screens show how to
perform Key Registration.
HINT:
This function requires the use of one Registered Master Key. The use of a Sub Key
will NOT complete Key Registration.
Page 4 of 9
Page 5 of 9
Key Code
Erasure
This function allows the user to erase all the Key Codes for Transponder Keys except the
Registered Master Key used during this function. The following screens show how to
perform Key Code Erasure.
HINT:
This function requires the use of one Registered Master Key. The use of a Sub Key
will NOT complete Key Code Erasure.
Page 6 of 9
Page 7 of 9
Auto
Registration
Closure
This function allows the user to close Auto Registration Mode when less than three keys
have been registered.
NOTE:
When a New ECU is installed, it is in the Auto Registration Mode. This mode allows
the Transponder Keys to automatically register as they are inserted into the Ignition
Cylinder. See the Repair Manual for further details.
CAUTION:
This function requires the use of one Registered Master Key. The use of a Sub Key
will NOT complete Auto Registration Closure. The use of a nontransponder key
during this function may damage the ECU.
Page 8 of 9
Page 9 of 9