Académique Documents
Professionnel Documents
Culture Documents
Top-View
Bottom-View
Features
Mechanical Parameters
z Dimensions: 67 x 37 mm
z Working temperature: 0~70 Celsius
z Humidity Range: 20% ~ 90%
z Power Consumption: 1A @ 3.3V
Processor
z TI DM3730 DaVinci Digital Media Processor (pin-to-pin compatible with TI AM3715)
- Up to 1-GHz ARM Cortex-A8 Core, also supports 300, 600, and 800-MHz operation
- Up to 800-MHz TMS320C64x+ DSP Core, also supports 260, 520 and 660-MHz
operation (DM3730 only)
- NEON SIMD Coprocessor
- POWERVR SGX Graphics Accelerator
- ARM: 32KB I-Cache; 32KB D-Cache; 256KB L2 Cache
- Onchip 32KB ROM and 64KB Shared SDRAM
Memory
z 256MB DDR SDRAM, 32-bit
z 512MB NAND Flash, 16-bit
Onboard Headers and Signals Routed to Pins
z 12-bit Camera interface (30-pin FPC connector, support CCD or CMOS camera)
z 1-channal 4-wire JTAG interface (10-pin 1.0mm pitch connector)
z 6 LEDs (programmable status LEDs)
z 2-channel SPI
z GPMC bus (16-bit data bus, 10-bit address bus, 4 chip-selection signals and several
control signals)
z 3-channel 5-wire UARTs
z 1-channel ULPI (USB1 HS)
z Audio in/out
1
z
z
z
z
1-channel I2C
2-channel McBSP (McBSP1 and McBSP3, McBSP3 is multiplex with UART2)
2-channel SD/MMC: MMC1 (8-wire), MMC2 (4-wire)
24-bit DSS interface
General Description
Embest Mini8510 processor card is based on TIs DM3730 DaVinci Digital Media processor
which is powered by 1GHz ARM Cortex-A8 and 800MHz C64x+ DSP core. The Mini8510
hardware is compatible with Embest Mini8100 OMAP3530 processor card which is convenient
for customers who used Mini8100 before to upgrade to Mini8510 so as to migrate from the
OMAP3530 to DM3730 for their embedded designs.
The SBC8100 expansion board for integration of the Embest Mini8100 processor card can be also
used for Mini8510. The processor card is connected with SBC8100 expansion board through two
1.27mm space 2*45-pin dip connectors. We call the upgraded DM3730 system SBC8100 Plus.
Embest offers Linux 2.6.32 and WinCE6.0 BSP for this board. Customers can leverage our
experience to increase your own productivity. The optimal embedded microprocessor solution
provides users with a flexible development environment based on DM3730 and a shortened
development timeframe.
Nand Flash
JTAG
TV
GPIO
UART
DM3730 / AM3715
1GHz ARM Cortex-A8
800MHz TMS320C64x (DM3730 only)
GPMC NEON, SGX Graphics Accelerator
512MB 16bit
Audio in
I2C
Audio out
SDRC
DDR
SDRAM
OTG
DSS
256MB 32bit
TPS65930
Power
Management
USB
Interface
CCD/CMOS
Interface
MMC
Keyboard
CONNECTOR to MAINBOARD
Dimensions
Camera interface
Embest Mini8510 processor card uses a 30-pin FPC connector, supporting CCD or CMOS camera.
Detailed pin explanation is as following:
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
Signal
GND
D0
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
GND
PCLK
GND
HS
VDD50
VS
VDD33
XCLKA
XCLKB
GND
FLD
WEN
STROBE
SDA
SCL
GND
VDD18
Description
GND
Digital image data bit 0
Digital image data bit 1
Digital image data bit 2
Digital image data bit 3
Digital image data bit 4
Digital image data bit 5
Digital image data bit 6
Digital image data bit 7
Digital image data bit 8
Digital image data bit 9
Digital image data bit 10
Digital image data bit 11
GND
Pixel clock
GND
Horizontal synchronization
5V
Vertical synchronization
3.3V
Clock output a
Clock output b
GND
Field identification
Write Enable
Flash strobe control signal
IIC master serial clock
IIC serial bidirectional data
GND
1.8V
JTAG interface
Embest Mini8510 processor card has a 10-pin 1.0mm pitch JTAG connector on board. Detailed
pin explanation is as following:
Pin
1
2
3
4
5
6
7
8
9
10
Signal
VDD18
TMS
TD1
NTRST
TD0
RTCK
TCK
EMU0
EMU1
GND
Description
1.8V output
Test mode select
Test data input
Test system reset
Test data output
Receive test clock
Test clock
Test emulation 0
Test Emulation 1
GND
Signal
G_NWE
G_NOE
G_NCS7GPT8G_DIR
G_NCS4GPT9DMAREQ1
G_NCS6GPT11DMAREQ3
6
7
8
9
10
11
12
13
14
15
16
17
18
19
G_NCS3DMAREQ0
GND
G_WAIT0
G_NBE0 / G_CLE
G_NATV_ALE
G_NBE1
HDQ_SIO
MMC1_D0
MMC1_D1
MMC1_D2
MMC1_D6/IO128
MMC1_D5/IO127
MMC1_D4/IO126
MMC1_D7/IO129
Description
GPMC Write Enable
GPMC Read Enable
GPMC Chip Select bit 7PWM or event for GP timer
8GPMC IO direction control for use with external
transceivers
GPMC Chip Select bit 7PWM or event for GP timer
9External DMA request 1
GPMC Chip Select bit 7PWM or event for GP timer 11
External DMA request 3
GPMC Chip Select bit 7External DMA request 0
GND
External indication of wait
Lower Byte Enable. Also used for Command Latch Enable
Address Valid or Address Latch Enable
Upper Byte Enable
Bidirectional HDQ 1-Wire control and data
MMC/SD Card Data bit 0
MMC/SD Card Data bit 1
MMC/SD Card Data bit 2
MMC/SD Card Data bit 6
MMC/SD Card Data bit 5
MMC/SD Card Data bit 4
MMC/SD Card Data bit 7
6
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
MMC1_D3
GND
MMC1_CLK
MMC1_CMD
VMMC1
UART3_RX_IRRX
UART3_CTS_RCTX
UART3_TX_IRTX
UART3_RTS_SD
DSS_ACBIAS
DSS_VSYNC
GND
DSS_HSYNC
DSS_CLK
DSS_D6
DSS_D8
DSS_D7
DSS_D9
DSS_D20
DSS_D17
DSS_D16
DSS_D18
DSS_D10
DSS_D5
DSS_D4
GND
DSS_D2
DSS_D3
DSS_D0
DSS_D15
DSS_D11
DSS_D23
DSS_D22
DSS_D14
DSS_D19
DSS_D13
DSS_D21
DSS_D1
DSS_D12
GND
MCBSP1_FSR/IO157
MCBSP1_CLKR/IO156
MCBSP1_FSX/IO161
MCBSP1_CLKS/IO160
MCBSP1_CLKX/IO162
MCBSP1_DR/IO159
MCBSP1_DX/IO158
GND
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
TV_OUTC
TV_OUTY
VDD33
IIC3_SCL
IIC3_SDA
IO25
IO27
BOOTJUMP
GND
VBUS
USB_DN
USB_ID
USB_DP
PWM0
KR0
KR1
KR2
KR3
KR4
VDD18
GND
VDD18
BKBAT
Signal
GND
G_D14
G_D13
G_D10
G_D8
G_D9
G_D5
G_D7
G_D3
G_D6
G_D12
G_D2
G_D11
G_D1
G_D4
G_D0
G_A2
G_A3
G_A1
G_A6
G_A4
Description
GND
GPMC data bit 14
GPMC data bit 13
GPMC data bit 10
GPMC data bit 8
GPMC data bit 9
GPMC data bit 5
GPMC data bit 7
GPMC data bit 3
GPMC data bit 6
GPMC data bit 12
GPMC data bit 2
GPMC data bit 11
GPMC data bit 1
GPMC data bit 4
GPMC data bit 0
GPMC address bit 2
GPMC address bit 3
GPMC address bit 1
GPMC address bit 6
GPMC address bit 4
8
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
G_A7
G_A5
G_A8
G_A9
G_D15
G_A10
GND
SPI2_CS1 GPT8
SPI2_CS10 GPT11
SPI2_SIMO GPT9
SPI2_CLK
SPI2_SOMI GPT10
SPI1_CS3
SPI1_CS0
SPI1_SIMO
SPI1_SOMI
SPI1_CLK
GND
GPIO0
MMC2_D2 SPI3_CS1
MMC2_D3SPI3_CS0
MMC2_D0SPI3_SOMI
MMC2_D1
MMC2_CMDSPI3_SIMO
MMC2_CLKSPI3_CLK
BSP3_DRUART2_RTS
BSP3_CLKUART2_TX
BSP3_FSXUART2_RX
BSP3_DXUART2_CTS
GND
UART1_CTS
UART1_TX
UART1_RX
UART1_RTS
USB1HS_STP
USB1HS_D3
USB1HS_D5
USB1HS_6
USB1HS_D7
USB1HS_D1
USB1HS_D2
USB1HS_D4
USB1HS_D0
USB1HS_NXT
USB1HS_CLK
GND
USB1HS_DIR
SYS_CLKOUT1
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
LEDA
LEDB
ADCIN0
NRESPWRON
NRESWARM
SYSEN
GND
REGEN
ADCIN1
KC0
KC1
KC2
KC3
AUDIO_IN
AUDIO_OR
AUXR
AUDIO_OL
GND
VBAT
ON/OFF
VBAT
LED leg A
LED leg B
ADC input0 (Battery type)
Power On Reset
Warm Boot Reset (open drain output)
System enable output
GND
Enable signal for external LDO
ADC input1 (General-purpose ADC input)
Keypad column 0
Keypad column 0
Keypad column 0
Keypad column 0
Analog microphone bias 1
Predriver output right P for external class-D amplifier
Auxiliary audio input right
Predriver output left P for external class-D amplifier
GND
Power supply (3V - 4.2V 1.5A)
Input; detect a control command to start or stop the systerm
Power supply (3V - 4.2V 1.5A)
Order Information
Order No.
Item
Options
Price
T400304
Embest Mini8510 Processor Card
Embest SBC8100 Plus Single Board Computer
Please contact Embest