Académique Documents
Professionnel Documents
Culture Documents
SDG963 SDG96NSDG96E
ELECTRIC POWER METER
Users manual
SYO
CATALOG
1 General Description ..................................................................................................... 3
1.1
1.2
Main Function..................................................................................................... 3
1.2.1
1.2.2
I/O Functions.............................................................................................. 3
1.2.3
Communications ........................................................................................... 4
1.2.4
Memory ........................................................................................................ 4
1.2.5
Installation .......................................................................................................... 4
2.2
Connection .......................................................................................................... 4
2.2.1
2.2.2
3.2
SYO
1 General Description
SDG96 is an intelligent multi-parameter meter and control device. It is widely used in
electric power system. It directly measures power parameters as follows: voltage, current, power,
power factor, frequency, electric energy and etc. It monitors four switch inputs and outputs two
relays.
SDG96 has one independent RS485 communication interfaces which enable convenient
communications with other devices. It also has opening communication agreement open to users.
1.2.1 Measurements
SDG96 provides real time parameters as follows:
VoltagesUaUbUcUabUbcUca
CurrentsIaIbIc
Four quadrant active powersPaPbPcPs
Four quadrant reactive powersQaQbQcQs
Apparent powersVaIaVbIbVcIc
Power factorsPFaPFbPFcPF
FrequencyF
Energy measurementspositive active energynegative active energy, positive reactive
energynegative reactive energy
1.2.2
I/O Ports
SYO
1.2.3
Communications
SDG96 has one independent RS485 communication interfaces which to receive and
send
1.2.4
Memory
To set one of the parameters, use the buttons on the panelsuch as the ratio of current
or voltagecommunication address, baud and so on. All settings are reserved in the EEROM
which does not lose any data even when power is off.
Installation
2.1
Installation
Attentions
SDG96 has no adjustable element. Dont open the crust; otherwise the power will be off.
2.2
Connection
2.2.1
Terminals
SYO
21 22 23 24 25 26 27 28
29 30 31 32 33 34
RS485
4-20mA
N PE PE
AC/DC 80 265V
11 12 13 14 15 16 17 18 19 20
IN1 IN2 IN3 IN4 INGND
J1 J1 J2 J2
Ia Ia Ib Ib Ic Ic Ua Ub Uc Un
1
2.2.2
Measurement loop
1. 3-phase/4-wires(3-CT)
2. 3-phase/3-wires(2-CT)
9 10
SYO
2.2.3
Connection Attentions
SDG96
3.1
Display setting
Keys layout
ESC
MOV
ADD
ENT
MOVThe
ADDThe
1:
2:
3:
Example 1:Selecting 3,To display 3-phase total active powers , 3-phase total
reactive powers , 3-phase average power factor .The unit is M.
The setting step is:
1 3: M
SYO
1. ADD 3 MOV
M
1.To press ADD key lighting arrowhead 3,to press MOV lighting M.
2. MOVADD3
2.To press MOVorADDfor three seconds ,This setting will write into The
meter which will work according to the setting.
K
M
V A W Wh
V
Var
A Varh
V PF
A Hz
To press [ESC][ENT] for three seconds at same time ,you can set parameters:PO-P9.
[ESC][ENT]3 P0-P9
_P0_
CT
LED1 LED2 LED3 LED4
Note: LED1,LED2,LED3,LED4 are fore digit tubes.
LED1,LED2,LED3,LED4 .
When you enter the interface of parameter setting ,The keys are defined as follows:
ESCEscape
MOVRight move
ADDAdd 1
ENTenter
P0: Setting the ratio of current transformer CT .The default value is 1.
CT 1
The range is 09999the setting value=main current/secondary current.
SYO
09999= /
Example 2: The ratio of currents is 100/5,then setting value CT=20.
2 100/5A CT = 100/5 = 20
The steps are:
1. To press [ESC] and [ENT] keys for three seconds at same time ,It will enter
the interface of setting parameters ,it shown as:
[ESC][ENT]3
_P0_
CT
2.To press ENT key ,it will enter the menu.ENT
_P0_
CT
1
3. To press MOV key to change the parameter.MOV
_P0_
CT
0001
Note: The digit selected will be flash ,to press ADD once the digit
will be add one.
ADD 1
4. To press MOV twice ,the third digit will be selected ,To pressADD
key twice change the digit to two ,then press MOVkey once the forth digit will
be selected, to pressADDkey change the digit to zero.
MOV 2 3 ADD 2MOV 1 4
ADD 0
5.To press ENT key to write the parameters into the meter.
ENT
_P0_
CT
20
6.To press ESC key return to the main menu . To press ADD key to change
other parameters.
SYO
_P0_
CT
_P1_
PT
ADD
_P2_
ADD
ADD
LED4connection mode
33-phase /3-wires 4
3-phase/4-wires
Example 2:setting steps
2.
P4: To setting voltage and connection mode, the default value is 14.
14
LED3: Setting voltage mode,
1:line voltage, 2:phase voltage.
LED3
12
LED4: connection mode
3:3 phases 3 wires ,4:3 phases 4 wires
SYO
LED4
34
Setting steps are shown as example 2.
2.
P5:Setting analog output(4-20mA)
P_05
A
P_05
A1.00
577
2. To press ADDselecting chanel A1,A2,A3.
ADD A1,A2,A3
A1: AO1A2: AO2, A3: AO3
3. To press MOVsetting parameter needed
MOV
P_05
A1.00
577
The parameter type, the order is showed in communication list,
10
SYO
Example 3: A01 to output 3phases average voltage, The second voltage is 57.7V
A02 to output 3phases average current, The second current is 5A.
3A01: 57.7V
A02: 5A
P_05
A1.03
577
After setting ,To press ENTkey, then press ADDselecting channel A2.
ENTADD A2
P_05
A2.00
577
To press MOVkey setting the parameter you need.
MOV
P_05
A2.07
5000
After setting to press ENTkey, then ESCkey to exit.
ENTESC
P6: To permit
YES NO NO
P_06
Clre
11
SYO
P_06
Clre
no
2. To press ADDkey to select YES or NO.
ADD YES-NO
3. To press ENTkey to write the setting into the meter
ENT
4. To press ESC key once to exit, to press ESC key twice to exit main
menu
ESCESC
P7: To execute the energy reset YES or No , the default value is NO.
YES NO NO
After reset P6 and P7 return to default value.
P6,P7
P_07
Clr
P_07
Clr
no
2. To press ADDkey to select YES .
ADD YES
12
SYO
P_07
Clr
yes
3. To press ENTkey to clear energy at zero.
Note :To execute the energy reset need that P6 is selected YES at first and P7
is selected YES, After reset shown as follow:
ENT
P6: YES P7:
YES
P_07
Clr
0000
4. To press ENTkey once to exit, to press ENTkey twice to exit from setting
menu.
ESCESC
P8The states of switch IN and OUT
P_08
00
0000
switch out J1
switch in .
O:open
J2. J1 J2
1:close.
13
SYO
P-09
C-1
P-09
2010.
02.28
Date: 2010.02.28
2010.02.28
2. To press MOVkey, the selected digital will be flash, To press ADD
key to change it. After change it, to press ENTkey to finish calendar setting.
To press ADDkey again enter time setting in same way as calendar.
MOVADD
ENTADD
P-09
15.
26.38
Time:15:26:38
15.26.38
3. To press ESCkey return to main menu.
ESC
* P10: setting energy time interval
14
SYO
P-10
C-2
P-10
b0_0
00.00
b0~b7 express respectively 8 time interval.
b0_x
b0~b7 8
b0_x
x: 0- 1- 2- 3- 4-
LED1 LED2:
LED3 LED4:
2. To press MOVkey, the selected digital will be flash, To press ADD
key to change it. After change it, to press ENTkey to finish . To press ADDkey again
enter next time interval setting in same way .
MOVADD
ENTADD
P-10
b1_1
07.30
3. To press ENTkey enter the setting menu.
15
SYO
ESC
P-11
C-3
P-11
C-3
01.00
scope()01.00~28.23
P-12
LOP
16
SYO
P-12
LOP
ON
2. To press ADDkey to select ON-OFF.
ADD ON-OFF
3. After selecting ,to press ENTto write into meter.
ENT
4.To press ESCkey enter the setting menu.
ESC
P13: Factory check menu, entering need password.
P-13
PSD
* SDG96
17
SYO
The product will be packed when it is transported. Keep it clean and uncrushed. The ambient
temperature range is 2070. Relative humidity must not exceed 90%
Technology Targets
As follows in list 4:
parameters
U, I are 0.2%P, Q are 0.2%
Ep is 0.2%Eq is 0.2%
Precision level
Display
0.4LED
Connection
3-phase 3-wire/4-wire
AC100V220V400V
Range
10288V(phase voltage)
Over load
Consumption
<0.2VA(per phase)
Impedance
>300k
Rating
AC 1A5A
Range
0.0056A
Over load
Consumption
<0.4VA(per phase)
Impedance
<20m
Voltage
Rating
AC Inputs
Current
Frequency
50/60Hz10%
Electric energy
Power
supply
Output
Size
43
Range
ACDC 80V270V
Consumption
0.4VA
Communication
RS485MODBUSRTU
Pulse output
Relays ability
AC 220V 5A
Input
Ordinary opening
Work condition
1055relative humidity93%
Sea level2500m
Insulation voltage
input>2kVoutput>2kV
power supply>1.5kV
Insulation resistance
100M
Panel size
9696mm
Hole size
9191mm
18
SYO
Packing size
lengthwidthheight: 157140110
19